Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Performance Evaluation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Critical heat flux impact due to cladding surface condition

This paper demonstrates how the cladding surface condition can impact fuel rod heat transfer and critical heat flux (CHF) performance at Pressurized Water Reactor (PWR) type conditions. The cladding surface that is investigated here is a surface with a crud deposit similar to ones observed in a PWR reactor. Tests are performed in the Westinghouse WALT (Westinghouse Advanced Loop Tester) loop test facility where a single ZIRLO clad electrically heated rod with approximately one-foot length is tested at PWR thermal hydraulic conditions and chemistry. Tests are performed for a normal clean rod surface, an oxide surface and with CRUD deposits to investigate the impact on fuel rod heat transfer and CHF performance. The CRUD deposit is characterized for thickness, chimney size and porosity. Test results are presented for the different cladding surface conditions along with comparisons to evaluations performed in the literature for different surfaces at pool boiling conditions. The results indicate that the WALT loop test facility can produce CHF test results which are repeatable for the same heater rod and for different rods with the same surface condition. CHF test results for a ZIRLO cladding surface with a CRUD deposit near 20 microns typical of PWR deposits show similar CHF performance to clean rod surfaces. A noticeable increase in CHF performance was observed for a ZIRLO cladding surface with a thermal oxide layer based on one CHF measurement.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Examining the Role of IMU Health Characterization and Monitoring in UAS Safety

Inertial measurement units (IMUs) can be vital for vehicle attitude and position estimation in unmanned aerial vehicles (UAVs). Degradation in these units could result in incorrect position estimates that are utilized in vehicle control, trajectory prediction, and other critical systems; however, the modes and effects of degradation in these IMUs are not well understood. In order to quantify the risk posed by degradation in these sensors, a study was conducted on the types of IMUs prevalent in the commercial market, their known failure modes, and the applicability to health monitoring methods for risk reduction and increased safety in an increasingly autonomous airspace. First, use cases and failure modes of the various types and reliability of commercially available IMUs were reviewed, and knowledge gaps and issues in the field were identified. Noting that inexpensive and lightweight MEMS (Microelectromechanical Systems) IMUs are some of the most commonly used but least reliable sensors in sUAS (small Unmanned Aerial Systems), five inexpensive MEMS IMUs were chosen for a performance evaluation study, selected from the Pixhawk autopilot systems, hobby sUAS, and prior NASA experimental studies. For each of these IMUs, a 10-minute bias test and a 12-hour drift test were performed for the accelerometers in a benchtop setting, using a BeagleBone Black for data collection. Using these results, the sensors’ performance is compared to their reported specifications, and the utility of implementing diagnostic methods for MEMS IMUs for research and commercial applications is evaluated. The paper concludes with a planned study for the evaluation of vibration-induced degradation for the selected sensors.

IMUs↗

Modeling of Irradiation Hardening of Polycrystalline Materials

High energy particle irradiation of structural polycrystalline materials usually produces irradiation hardening and embrittlement. The development of predict capability for the influence of irradiation on mechanical behavior is very important in materials design for next generation reactors. In this work a multiscale approach was implemented to predict irradiation hardening of body centered cubic (bcc) alpha-iron. The effect of defect density, texture and grain boundary was investigated. In the microscale, dislocation dynamics models were used to predict the critical resolved shear stress from the evolution of local dislocation and defects. In the macroscale, a viscoplastic self-consistent model was applied to predict the irradiation hardening in samples with changes in texture and grain boundary. This multiscale modeling can guide performance evaluation of structural materials used in next generation nuclear reactors.

36 MATERIALS SCIENCE↗

Fine pointing of the Solar Optical Telescope in the Space Shuttle environment

Instruments requiring fine (i.e., sub-arcsecond) pointing, such as the Solar Optical Telescope (SOT), must be equipped with two-stage pointing devices, coarse and fine. Coarse pointing will be performed by a gimbal system, such as the Instrument Pointing System, while the image motion compensation (IMC) will provide fine pointing. This paper describes work performed on the SOT concept design that illustrates IMC as applied to SOT. The SOT control system was modeled in the frequency domain to evaluate performance, stability, and bandwidth requirements. The two requirements of the pointing control, i.e., the 2 arcsecond reproducibility and 0.03 arcsecond rms pointing jitter, can be satisfied by use of IMC at about 20 Hz bandwidth. The need for this high bandwidth is related to Shuttle-induced disturbances that arise primarily from man push-offs and vernier thruster firings. A block diagram of SOT model/stability analysis, schematic illustrations of the SOT pointing system, and a structural model summary are included.

Gowrinathan, S.↗

EVALUATION OF LVDTS FOR USE IN ATR IRRADIATION EXPERIMENTS

New materials are being considered for fuel, cladding, and structures in next generation and existing nuclear reactors. Such materials can experience significant dimensional changes during high temperature irradiation. Currently, these changes are determined by repeatedly irradiating a specimen for a defined period of time in the Advanced Test Reactor (ATR) and then removing it from the reactor for evaluation. The time and labor to remove, examine, and return irradiated samples for each measurement makes this approach very expensive. In addition, such techniques provide limited data and may disturb the phenomena of interest. To address these issues, the Idaho National Laboratory (INL) recently initiated efforts to evaluate candidate linear variable differential transducers (LVDTs) for use during high temperature irradiation experiments in typical ATR test locations. Two nuclear grade LVDTs are under consideration – a smaller diameter design qualified for temperatures up to 350 °C and a larger design with capabilities to 500 °C. Calibration and long duration performance evaluations are underway for temperatures up to 600 ºC. This paper presents results from these evaluations, which will ultimately lead to recommendations for an improved design for use in the ATR.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

SU-E-T-512: Intrinsic Characteristics of the Nine Detectors and Evaluation of Their Performance in Non-Equilibrium Radiation Dosimetry

Purpose The aim for the study was to compare intrinsic characteristics of the nine detectors and evaluate their performance in non-equilibrium radiation dosimetry. Methods The intrinsic characteristics of the nine detectors that were evaluated are based on the composition and size of the active volume, operating voltage, initial recombination of the collected charge, temperature, the effective cross section of the detectors. The shortterm stability and collection efficiency has been investigated. The minimum radiation detection sensitivity and detectors leakage current has been measured. The sensitivity to changes in energy spectrum as well as change in incident beam angles were measured an analyzed. Results The short-term stability of the measurements within every detector showed consistency in the measured values with the highest value of the standard deviation of the mean not exceeding 0.5%. Air ion chamber detectors showed minimum sensitivity to change in incident beam angles while diode detectors underestimated measurements up to 16%. Comparing the slope of the tangents for detector’s sensitivity curve, diode detectors illustrate more sensitivity to change in photon spectrum than ion chamber detectors. The change in radiation detection sensitivity with increase in dose delivered has been observed for semiconductor detectors with maximum deviation 0.01% for doses between 1 Gy and 10 Gy. Leakage current has been mainly influenced by bias voltage (ion chamber detectors) and room light intensity (diode detectors). With dose per pulse varying from 1.47E−4 to 5.1E−4 Gy/pulse the maximum change in collection efficiency was 1.4% for the air ion chambers up to 8% for liquid filled ion chamber. Conclusion Broad range of measurements performed showed all the detectors susceptible to some limitations and while they are suitable for use in broad scope of applications, careful selection has to be made for particular range of measurements.

60 APPLIED LIFE SCIENCES↗

Highly-Active and Contaminant-Tolerant Cathodes for Durable Solid Oxide Fuel Cells (Final Report)

The objective of this project is to investigate the fundamental degradation methods occurring in solid oxide fuel cell (SOFC) cathodes when exposed to chromium and carbon dioxide contamination and to rationally design alkaline earth-based catalysts to increase stability and tolerance to contaminate poisoning. With a mechanistic and fundamental understanding of the degradation methods, advanced catalytic surface modifications can be applied to reduce degradation. The specific technical objectives are: (1) To identify/develop new catalysts (alkaline-earth based-) that are compatible chemically with the state-of-the-art cathode materials at high temperatures required for fabrication and with contaminates commonly encountered under operating conditions; (2) To improve the infiltration process for optimal control of the thickness, composition, and uniformity of the catalyst coatings; (3) To evaluate the electro-catalytic activity toward ORR of the chemically-stable materials when exposed to different types of contaminants using electrical conductivity relaxation measurements on bar samples and performance evaluation of catalyst-infiltrated cathodes; (4) To unravel the contamination-tolerant mechanisms of the new catalyst coatings under realistic environmental conditions (with different types of contaminants) using powerful in situ and in operando characterization techniques performed on model cells with thin-film/pattern electrodes, as guided by modeling and simulation; (5) To establish scientific basis for rational design of new catalysts of high tolerance to contaminants; (6) To validate the long term stability of modified LSCF cathodes in commercially available cells/stacks under ROC. Alkaline earth-based catalysts have been systematically explored and tested under various contamination conditions. BaCoO 3-δ (BCO) was shown to produce the best catalytic activity enhancement as well as stability in a variety of contaminating conditions, including CO 2 and chromium. The microstructural evolution was investigated with SEM, EDS, and Raman spectroscopy, showing the BCO catalyst prevents the formation of insulating SrCrO 4 by forming electrically conductive BaCrO 4 . Electrochemical relaxation measurements determined the BCO catalyst coatings increased the surface diffusion coefficient but did not significantly affect the diffusion coefficient and determined an optimum surface modification layer of 100 nm. A novel Ba 0.9 Co 0.7 Fe 0.2 Nb 0.1 O x (BCFN) catalyst was also shown to have excellent stability in chromium containing atmospheres. A novel surface sol-gel (SSG) surface modification, which offers superior thickness and compositional control, was applied to SOFCs to produce BaO catalyst coatings. SSG BaO coatings were shown to produce conformal coatings on the electrode surface, greatly increasing stability in chromium containing atmospheres. An atomic level mechanistic approach was applied to investigate the stability of PrBa 0.8 Ca 0.2 Co2O 5+δ (PBCC) with respect to a variety of common contaminants, demonstrating thermodynamically its superior stability in CO2 containing atmospheres. Finally, the best catalyst coatings demonstrated in this project, BCO and PBCC, were applied to full cells which demonstrated superior stability for over 300 hours in CO 2 and Cr atmospheres.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Highly-Active and Contaminant-Tolerant Cathodes for Durable Solid Oxide Fuel Cells

The objective of this project is to investigate the fundamental degradation methods occurring in solid oxide fuel cell (SOFC) cathodes when exposed to chromium and carbon dioxide contamination and to rationally design alkaline earth-based catalysts to increase stability and tolerance to contaminate poisoning. With a mechanistic and fundamental understanding of the degradation methods, advanced catalytic surface modifications can be applied to reduce degradation. The specific technical objectives are: (1) To identify/develop new catalysts (alkaline-earth based-) that are compatible chemically with the state-of-the-art cathode materials at high temperatures required for fabrication and with contaminates commonly encountered under operating conditions; (2) To improve the infiltration process for optimal control of the thickness, composition, and uniformity of the catalyst coatings; (3) To evaluate the electro-catalytic activity toward ORR of the chemically-stable materials when exposed to different types of contaminants using electrical conductivity relaxation measurements on bar samples and performance evaluation of catalyst-infiltrated cathodes; (4) To unravel the contamination-tolerant mechanisms of the new catalyst coatings under realistic environmental conditions (with different types of contaminants) using powerful in situ and in operando characterization techniques performed on model cells with thin-film/pattern electrodes, as guided by modeling and simulation; (5) To establish scientific basis for rational design of new catalysts of high tolerance to contaminants; (6) To validate the long term stability of modified LSCF cathodes in commercially available cells/stacks under ROC. Alkaline earth-based catalysts have been systematically explored and tested under various contamination conditions. BaCoO 3-δ (BCO) was shown to produce the best catalytic activity enhancement as well as stability in a variety of contaminating conditions, including CO 2 and chromium. The microstructural evolution was investigated with SEM, EDS, and Raman spectroscopy, showing the BCO catalyst prevents the formation of insulating SrCrO 4 by forming electrically conductive BaCrO 4 . Electrochemical relaxation measurements determined the BCO catalyst coatings increased the surface diffusion coefficient but did not significantly affect the diffusion coefficient and determined an optimum surface modification layer of 100 nm. A novel Ba 0.9 Co 0.7 Fe 0.2 Nb 0.1 O x (BCFN) catalyst was also shown to have excellent stability in chromium containing atmospheres. A novel surface sol-gel (SSG) surface modification, which offers superior thickness and compositional control, was applied to SOFCs to produce BaO catalyst coatings. SSG BaO coatings were shown to produce conformal coatings on the electrode surface, greatly4 increasing stability in chromium containing atmospheres. An atomic level mechanistic approach was applied to investigate the stability of PrBa 0.8 Ca 0.2 Co 2 O 5+δ (PBCC) with respect to a variety of common contaminants, demonstrating thermodynamically its superior stability in CO 2 containing atmospheres. Finally, the best catalyst coatings demonstrated in this project, BCO and PBCC, were applied to full cells which demonstrated superior stability for over 300 hours in CO 2 and Cr atmospheres.

30 DIRECT ENERGY CONVERSION↗

Highly-Active and Contaminant-Tolerant Cathodes for Durable Solid Oxide Fuel Cells

The objective of this project is to investigate the fundamental degradation methods occurring in solid oxide fuel cell (SOFC) cathodes when exposed to chromium and carbon dioxide contamination and to rationally design alkaline earth-based catalysts to increase stability and tolerance to contaminate poisoning. With a mechanistic and fundamental understanding of the degradation methods, advanced catalytic surface modifications can be applied to reduce degradation. The specific technical objectives are: (1) To identify/develop new catalysts (alkaline-earth based-) that are compatible chemically with the state-of-the-art cathode materials at high temperatures required for fabrication and with contaminates commonly encountered under operating conditions; (2) To improve the infiltration process for optimal control of the thickness, composition, and uniformity of the catalyst coatings; (3) To evaluate the electro-catalytic activity toward ORR of the chemically-stable materials when exposed to different types of contaminants using electrical conductivity relaxation measurements on bar samples and performance evaluation of catalyst-infiltrated cathodes; (4) To unravel the contamination-tolerant mechanisms of the new catalyst coatings under realistic environmental conditions (with different types of contaminants) using powerful in situ and in operando characterization techniques performed on model cells with thin-film/pattern electrodes, as guided by modeling and simulation; (5) To establish scientific basis for rational design of new catalysts of high tolerance to contaminants; (6) To validate the long term stability of modified LSCF cathodes in commercially available cells/stacks under ROC. Alkaline earth-based catalysts have been systematically explored and tested under various contamination conditions. BaCoO 3-δ (BCO) was shown to produce the best catalytic activity enhancement as well as stability in a variety of contaminating conditions, including CO 2 and chromium. The microstructural evolution was investigated with SEM, EDS, and Raman spectroscopy, showing the BCO catalyst prevents the formation of insulating SrCrO 4 by forming electrically conductive BaCrO 4 . Electrochemical relaxation measurements determined the BCO catalyst coatings increased the surface diffusion coefficient but did not significantly affect the diffusion coefficient and determined an optimum surface modification layer of 100 nm. A novel Ba 0.9 Co 0.7 Fe 0.2 Nb 0.1 O x (BCFN) catalyst was also shown to have excellent stability in chromium containing atmospheres. A novel surface sol-gel (SSG) surface modification, which offers superior thickness and compositional control, was applied to SOFCs to produce BaO catalyst coatings. SSG BaO coatings were shown to produce conformal coatings on the electrode surface, greatly 4 increasing stability in chromium containing atmospheres. An atomic level mechanistic approach was applied to investigate the stability of PrBa 0.8 Ca 0.2 Co 2 O 5+δ (PBCC) with respect to a variety of common contaminants, demonstrating thermodynamically its superior stability in CO 2 containing atmospheres. Finally, the best catalyst coatings demonstrated in this project, BCO and PBCC, were applied to full cells which demonstrated superior stability for over 300 hours in CO 2 and Cr atmospheres

01 COAL, LIGNITE, AND PEAT↗

Parallel algorithms for simulating continuous time Markov chains

We have previously shown that the mathematical technique of uniformization can serve as the basis of synchronization for the parallel simulation of continuous-time Markov chains. This paper reviews the basic method and compares five different methods based on uniformization, evaluating their strengths and weaknesses as a function of problem characteristics. The methods vary in their use of optimism, logical aggregation, communication management, and adaptivity. Performance evaluation is conducted on the Intel Touchstone Delta multiprocessor, using up to 256 processors.

Nicol, David M.↗

Health Monitoring System for Composite Structures

An automated system was developed to monitor the health status of composites. It uses the vibration characteristics of composites to identify a component's damage condition. The vibration responses are characterized by a set of signal features defined in the time, frequency and spatial domains. The identification of these changes in the vibration characteristics corresponding to different health conditions was performed using pattern recognition principles. This allows efficient data reduction and interpretation of vast amounts of information. Test components were manufactured from isogrid panels to evaluate performance of the monitoring system. The components were damaged by impact to simulate different health conditions. Free vibration response was induced by a tap test on the test components. The monitoring system was trained using these free vibration responses to identify three different health conditions. They are undamaged vs. damaged, damage location and damage zone size. High reliability in identifying the correct component health condition was achieved by the monitoring system.

Tang, S. S.↗

Status of WSTF Pyrovalve Handbook Development in Year 2000

Significant data have been generated through various spacecraft propulsion system projects involving the use of pyrotechnically operated valves (pyrovalves). These data need to be analyzed, interpreted, summarized, associated, and formatted so they can be made available for spacecraft propulsion system design involving pyrovalves and used to specify test procedures in the performance evaluation and qualification of these systems. To meet this need, a Pyrovalve Handbook is being developed at the NASA White Sands Test Facility. Standards of performance for pyrovalve applications are being formulated under the sponsorship of the NASA Technical Standards Program, as are pyrovalve testing standards under the sponsorship of the NASA Safety and Risk Management Program. The ultimate goal is to have the Handbook adopted as a voluntary standard under the guidance of the AIAA Energetic Components and Systems Technical Committee and, in a more restrictive format, become an integral part of ISO standards for Explosive Systems and Devices Used on Space Vehicles. Feedback from both Government and industry is encouraged and will be the focus of the presentation. It is especially critical that feedback be received on content and formatting of the Handbook to maximize benefit to the technical community. Submission of validated data from organizations outside of NASA is also encouraged.

Howard, Julien L.↗

Cyber-Resilient Design Methodology for Microgrids

Recent advancement in tools has helped with microgrid design, development, planning and operation. Microgrids offer a unique application based on users with different requirements for tools. The process of designing, constructing, commissioning, and assessing a microgrid is not always straightforward due to these distinct requirements. Additionally, metrics are needed for performance evaluation. This panel will offer an overview and description of tools that helps with microgrid design, construction, planning, operation, cyber security, and metrics-driven performance assessment driven by multiple diverse applications and use cases.

CCE↗

Multifunctional cement for geothermal wells

This report compiles the work of BNL in support of Thermal Shock Resistant Cement evaluations (TSRC) by Schlumberger. BNL has worked on the formulation of thermal-shock resistant cement since 2011. All the materials on the blend including publications and presentations are in public domain and were sent to Schlumberger for review prior the beginning of the evaluations. Initial efforts focused on achieving long and controlled thickening time of TSRC at 85°C in thickening time tests in a pressurized consistometer. Since the results of BNL set control were not reproduced by Schlumberger technical feedback on Schlumberger testing was among the main efforts of the BNL team in the beginning of the collaboration. When it became clear that the main reason of results deviation was the difference in the mode of retarder addition (dry-blended at BNL and pre-dissolved at Schlumberger) the efforts shifted to the possible decrease in the cost of the formulation by changing concentrations and nature of the alkali activator as well as evaluating performance of more economical formulations with calcium-aluminate cement, Secar #51, Secar #71 and Ciment Fondu, suggested by Schlumberger based on communications with Kerneos (supplier of calcium aluminate cements). Another piece of information obtained by Schlumberger from Kerneos that prompted evaluations of different calcium-aluminate cements in the composition of TSRC was the fact that originally used Secar#80 contains some performance-improving additives that may interfere with the set control and rheological properties of the slurries. In summary, the report contains the following information: 1. Review of the setting behavior of TSRC slurries prepared by dry-blending TA powder or pre dissolving it in mix water in calorimetric tests at 85°C; 2. Results of evaluation of different alkali activators for improved compressive strength development and cost reduction; 3. Results of evaluation of Secar #51, 71 and cement Fondu as an alternative to Secar #80 in TSRC formulation – thermal shock tests and phases’ analyses of set cement; 4. A brief discussion of early-compressive-strength-development test conditions appropriate for geothermal wells.

15 GEOTHERMAL ENERGY↗

Multifunctional Cement for Geothermal Wells

This report compiles the work of BNL in support of Thermal Shock Resistant Cement evaluations (TSRC) by Schlumberger. BNL has worked on the formulation of thermal-shock resistant cement since 2011. All the materials on the blend including publications and presentations are in public domain and were sent to Schlumberger for review prior the beginning of the evaluations. Initial efforts focused on achieving long and controlled thickening time of TSRC at 85°C in thickening time tests in a pressurized consistometer. Since the results of BNL set control were not reproduced by Schlumberger technical feedback on Schlumberger testing was among the main efforts of the BNL team in the beginning of the collaboration. When it became clear that the main reason of results deviation was the difference in the mode of retarder addition (dry-blended at BNL and pre-dissolved at Schlumberger) the efforts shifted to the possible decrease in the cost of the formulation by changing concentrations and nature of the alkali activator as well as evaluating performance of more economical formulations with calcium-aluminate cement, Secar #51, Secar #71 and Ciment Fondu, suggested by Schlumberger based on communications with Kerneos (supplier of calcium aluminate cements). Another piece of information obtained by Schlumberger from Kerneos that prompted evaluations of different calcium-aluminate cements in the composition of TSRC was the fact that originally used Secar#80 contains some performance-improving additives that may interfere with the set control and rheological properties of the slurries. In summary, the report contains the following information: 1. Review of the setting behavior of TSRC slurries prepared by dry-blending TA powder or pre dissolving it in mix water in calorimetric tests at 85°C; 2. Results of evaluation of different alkali activators for improved compressive strength development and cost reduction; 3. Results of evaluation of Secar #51, 71 and cement Fondu as an alternative to Secar #80 in TSRC formulation – thermal shock tests and phases’ analyses of set cement; 4. A brief discussion of early-compressive-strength-development test conditions appropriate for geothermal wells.

36 MATERIALS SCIENCE↗

Fiscal year 1976 progress report on a feasibility study evaluating the use of surface penetrators for planetary exploration

The feasibility of employing penetrators for exploring Mars was examined. Eight areas of interest for key scientific experiments were identified. These include: seismic activity, imaging, geochemistry, water measurement, heatflow, meteorology, magnetometry, and biochemistry. In seven of the eight potential experiment categories this year's progress included: conceptual design, instrument fabrication, instrument performance evaluation, and shock loading of important components. Most of the components survived deceleration testing with negligible performance changes. Components intended to be placed inside the penetrator forebody were tested up to 3,500 g and components intended to be placed on the afterbody were tested up to 21,000 g. A field test program was conducted using tentative Mars penetrator mission constraints. Drop tests were performed at two selected terrestrial analog sites to determine the range of penetration depths for anticipated common Martian materials. Minimum penetration occurred in basalt at Amboy, California. Three full-scale penetrators penetrated 0.4 to 0.9 m into the basalt after passing through 0.3 to 0.5 m of alluvial overburden. Maximum penetration occurred in unconsolidated sediments at McCook, Nebraska. Two full-scale penetrators penetrated 2.5 to 8.5 m of sediment. Impact occurred in two kinds of sediment: loess and layered clay. Deceleration g loads of nominally 2,000 for the forebody and 20,000 for the afterbody did not present serious design problems for potential experiments. Penetrators have successfully impacted into terrestrial analogs of the probable extremes of potential Martian sites.

Blanchard, M. B.↗

Evaluation of advanced high rate Li-SOCl2 cells

Under NASA sponsorship, JPL is developing advanced, high rate Li-SOCl2 cells for future space missions. As part of this effort, Li-SOCl2 cells of various designs were examined for performance and safety. The cells differed from one another in several aspects, such as: nature of carbon cathode, catalysts, cell configuration, case polarity, and safety devices. Performance evaluation included constant-current discharge over a range of currents and temperatures. Abuse-testing consisted of shortcircuiting, charging, and over-discharge. Energy densities greater than 300 Wh/Kg at the C/2 rate were found for some designs. A cell design featuring a high-surface-area carbon cathode was found to deliver nearly 500 Wh/Kg at moderate discharge rates. Temperature influenced the performance significantly.

Deligiannis, F.↗