Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Spectral induced polarization (SIP) measurements across a PFAS-contaminated source zone

There is a pressing need for the development of field-scale, in situ screening technologies for assessing variations in aqueous film forming foam (AFFF) concentrations in soils at former fire training and storage sites. Field-scale Spectral Induced Polarization (SIP) geophysical measurements were acquired on a transect crossing an AFFF source zone. Soil samples were acquired from ten locations and used to determine variations in poly- and per-fluoroalkyl substances (PFAS) concentrations in soils and soil texture. These samples were also used to create triplicate soil columns for laboratory-grade SIP measurements. Field and laboratory observations provide evidence that SIP measurements are sensitive to the concentration of AFFF constituents associated with the pore surface in soils. The phase of the SIP measurements on the laboratory samples was linearly correlated with total soil-sorbed PFAS concentration. The phase from the field SIP measurements was highest over the location of maximum PFAS concentration measured on the laboratory samples, although a significant correlation between field-measured phase and laboratory-measured total PFAS concentration was not established. The sensitivity of the SIP response to the removal of soil PFAS using a methanol wash procedure (total PFAS concentration drop of 366 ppb) adds evidence for the case for SIP characterization of AFFF source zones. The results of these studies suggest that SIP might be developed into a field-scale technology for rapid, indirect assessment of AFFF source zones. Such a technology could improve the effectiveness of AFFF source zone characterization at reduced costs.

58 GEOSCIENCES↗

A unified approach to evaluating precipitation frequency estimates with uncertainty quantification: Application to Florida and California watersheds

Although a variety of climate datasets are now available, including observational and model products, there remains a pressing need for the development of a unified, automated and application-focused approach for evaluating and comparing climate extremes within and across these datasets. Precipitation frequency (PF) es- timates for extreme precipitation events are useful decision-relevant quantities among water managers. Our objective and quantitative framework for computing PF estimates of any duration uses known techniques in a novel combination. Our framework consists of three steps: (1) use of a regionalization-based statistical method for precipitation frequency estimation at observed sites; this involves hierarchical clustering (here we used Ward’s method) for delineating homogeneous regions, and regional frequency analysis using L-moments; (2) use of kriging for spatial mapping because of its advantages over other conventional interpolation methods; (3) use of z-scores accounts for estimation uncertainties when comparing PF estimates between datasets. The 24-h PF estimates in the Kissimmee-Southern Florida watershed (flat topography) and the Sacramento-San Joaquin watershed (complex topography) demonstrate the applicability of this approach in regions of any geographical complexity. Our results are shown to be reasonably calibrated using the probability integral transform (PIT) histogram of the best fitted distribution. Our results are compared with that of the NOAA Atlas 14 reports and show that for most of the stations the two estimates are statistically indistinguishable; and, the confidence intervals of our estimates are narrower than those of the NOAA estimates. Our approach is applicable to a variety of datasets and provides a baseline for assessing performance of climate models in historical simulations – a necessary first step towards analyzing future projections.

58 GEOSCIENCES↗

Characterization of Inconel 625 fabricated using powder-bed-based additive manufacturing technologies

The purpose of this study was to perform a comparative analysis of powder-bed-based additive manufacturing (AM) technologies during the production of metallic components using Inconel 625 powder material. The AM technologies explored in this study include electron beam powder bed fusion (EPBF), laser powder bed fusion (LPBF), and binder jetting technology. Samples were fabricated in two build directions (X and Z build orientations) for this evaluation process, where all specimens underwent a hot isostatic pressing (HIP) post-process. The comparison was made in terms of microstructure and mechanical properties including ultimate tensile strength (UTS), yield strength (YS), percent elongation, and modulus of elasticity (E). Microstructural characterization showed evidence of equiaxed grain formation for binder jetting and LPBF parts, whereas EPBF parts displayed a more columnar grain formation parallel to the build direction. Six specimens were tested per technology, three built in the X orientation and three built in the Z orientation. All six specimens were built in a single run of each AM machine. Results indicated that all three technologies are capable of meeting the minimum requirements of the ASTM F3056-14 standard for parts produced in the X orientation, with properties that are similar to wrought Inconel 625. In the Z orientation, however, only LPBF was able to meet the minimum standard requirements. Through the comparative analysis of the mechanical properties, here this work showed that LPBF outperformed the other technologies in a majority of the evaluated properties, followed by EPBF and binder jetting. An analysis of the fracture surfaces of tensile specimens was also performed, and it indicated ductile fracture (dimple rupture) for the specimens produced with all three of the AM technologies studied. Nevertheless, the characterization also showed certain differences in the fractured surfaces, such as the presence of un-sintered powder particles for the binder jetting processed Inconel 625, or the development of the so called woody structure for the EPBF processed material. This study can be used to determine distinct characteristics between the three powder-bed-based technologies for the fabrication of Inconel 625 that can further include other technologies and materials using similar approaches.

36 MATERIALS SCIENCE↗

Magnetic property and microstructure of single crystalline Nd2Fe14B ultrafine particles ball milled from HDDR powders

In this work we report the microstructure and magnetic property of single crystalline Nd2Fe14B ultrafine particles ball milled from HDDR Nd-Fe-B alloys. The average size of the particles is 283 nm, and TEM observation reveals that these particles are single crystalline. The coercivity of these particles is 6.0 kOe, which is much higher than that of the particles ball milled from sintered and hot pressed Nd-Fe-B magnets. Micromagnetic analysis shows that the coercivity degradation is caused by surface damage during ball milling. (C) 2013 Elsevier B.V. All rights reserved.

Li, WF↗

High temperature tensile properties of H13 tool steel fabricated via binder jet additive manufacturing

H13 is one of the most used steels for hot work tooling applications like die casting. Binder jet additive manufacturing (BJAM) offers a cost-effective solution to fabricate tools with performance enhancing features like internal cooling channels. While full densification of BJAM H13 has been demonstrated in the literature, the room and high temperature tensile properties of the material, and the effect of post-process treatments like hot isostatic pressing (HIP), and heat treatment (HT) are unknown. Here we use HIP+HT to obtain a combination of ultimate tensile strength (UTS) and elongation to failure that is superior to H13 fabricated via laser powder bed fusion and wire arc additive manufacturing. HIP+HT BJAM H13 has a superior UTS (1836 MPa) compared with conventionally processed (1671 MPa) H13 but has lower plastic elongation. We report that as-sintered samples have an extensive network of continuous grain boundary (GB) carbides that contribute to brittle fracture. HIP+HT results in partial dissolution of GB carbides and formation of a fine martensitic microstructure resulting in superior tensile strength and elongation compared with as-sintered H13. We use thermo-kinetic calculations to rationalize the effects of HIP+HT on microstructure and properties.

36 MATERIALS SCIENCE↗

High energy X-ray diffraction measurement of residual stresses in a monolithic aluminum clad uranium–10 wt% molybdenum fuel plate assembly

Residual stresses are expected in monolithic, aluminum clad uranium 10 wt% molybdenum (U–10Mo) nuclear fuel plates because of the large mismatch in thermal expansion between the two bonded materials. The full residual stress tensor of the U–10Mo foil in a fuel plate assembly was mapped with 0.1 mm resolution using high-energy (86 keV) X-ray diffraction. The in-plane stresses in the U–10Mo foil are strongly compressive, roughly -250 MPa in the longitudinal direction and -140 MPa in the transverse direction near the center of the fuel foil. The normal component of the stress is weakly compressive near the center of the foil and tensile near the corner. The disparity in the residual stress between the two in-plane directions far from the edges and the tensile normal stress suggest that plastic deformation in the aluminum cladding during fabrication by hot isostatic pressing also contributes to the residual stress field. A tensile in-plane residual stress is presumed to be present in the aluminum cladding to balance the large in-plane compressive stresses in the U–10Mo fuel foil, but cannot be directly measured with the current technique due to large grain size.

99 GENERAL AND MISCELLANEOUS↗

Solution-based approaches for making high-density sodalite waste forms to immobilize spent electrochemical salts

Three different solution-based approaches were taken to make sodalite minerals as a host for a mixed salt simulating the waste generated during the electrochemical separations process of nuclear fuel reprocessing that contains alkali, alkaline earth, and lanthanide chlorides plus trace iodine and actinides. All of the approaches included an aqueous solution of mixed chlorides (simulated waste) but the other reactants varied: (1) Al(OH)3 + NaOH + CS, (2) NaAlO2 + CS, and (3) Al2Si2O7 + NaOH, (CS = colloidal silica). The products were dried, ground, pressed into pellets, fired (650–950 °C), and characterized. Both 5 and 10 mass% of a Si-Na-B glass binder were introduced at different stages in the process. Route (2) proved the most successful at producing high sodalite fractions (up to 100%) with minimal glass binder additions and showed high consolidation potential (up to 91.4% of theoretical density). Detailed comparisons are provided of the results.

electrochemical↗

Neutron diffraction measurement of residual stresses, dislocation density and texture in Zr-bonded U-10Mo “mini” fuel foils and plates

Here, Al clad U-10Mo fuel plates are being considered for conversion of several research reactors from high-enriched to low-enriched U fuel. Neutron diffraction measurements of the textures, residual phase stresses, and dislocation densities in the individual phases of the mini-foils throughout several processing steps and following hot-isostatic pressing to the Al cladding, have been completed. Recovery and recrystallization of the bare U-10Mo fuel foil, as indicated by the dislocation density and texture, are observed depending on the state of the material prior to annealing and the duration and temperature of the annealing process. In general, the cladding procedure significantly reduces the dislocation density, but the final state of the clad plate, both texture and dislocation density, depends strongly on the final processing step of the fuel foil. In contrast, the residual stress state of the final plate is dominated by the thermal expansion mismatch of the constituent materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural and crystallographic effects of sol-gel synthesized Ti-doped UO 2 sintered under reducing conditions

Titanium (Ti)-doped UO 2 microspheres of three different Ti concentrations (1000, 2000, and 4000 wppm) were synthesized using an internal gelation process. The microspheres were pressed into pellets, and a two-step heat treatment was applied to form monolithic cylindrical pellets with high densities (≥95%TD). Microstructure of these samples consisted of equiaxed grains with >300% increase in average grain size compared to the undoped UO 2 pellets. Secondary Ti-rich chemical phases corresponding to a liquid eutectic formed during sintering were observed at grain boundaries of UO 2 for samples doped with 4000 wppm Ti. Furthermore, these Ti-rich chemical phases were not observed in 1000 or 2000 wppm Ti samples at microscale using electron microscopy investigations. The 0.02–0.04% lower lattice parameter values for the Ti-doped UO 2 samples compared to the undoped UO 2 confirms the incorporation of Ti into the UO 2 lattice.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural characterization of as-fabricated monolithic plates with boron carbide, aluminum boride, and zirconium boride burnable absorbers

The use of burnable absorbers can be beneficial for nuclear reactors by extending the fuel’s operational cycle, providing additional criticality control, and flattening the power profile. In this work, three burnable absorber materials (boron carbide, aluminum boride, and zirconium boride) embedded in aluminum have been fabricated into foils and clad in AA-6061 for potential use in high performance research reactors. The as-fabricated boron-containing phases were determined using transmission electron microscopy to be AlB2, B4C, and ZrB2. TEM also revealed weak bonding at the B4C-matrix interface. SEM showed a relatively uniform spatial distribution of boron-containing phases for all the candidate materials. Higher porosity was observed in the foil containing ZrB2 in its as-rolled condition. The porosity in the ZrB2 foil was reduced by hot isostatic pressing. The size and shape distributions of the boron-containing phases were analyzed on the criteria of cross-sectional area, perimeter, roundness, circularity, and aspect ratio. A method of converting the 2D burnable absorber dispersoids seen in cross-sectional microscopy images into 3D volumes was derived using both spherical and ellipsoidal geometry models. The difference in calculated burnable absorber dispersoid average volume between the two models ranges from 20% to 100%, which could impact burnable absorber burnout rates due to differences in neutron self-shielding.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Ion irradiation study of lithium silicates for fusion blanket applications

Here, this study reports on the microstructural and compositional evolutions, deuterium release and lithium loss behavior in lithium silicates. Pellets of biphasic Li 4 SiO 4 and Li 2 SiO 3 were fabricated using hot pressing of powders. Sequential irradiation with Si + , He + and D + ions was performed up to 773 K to emulate one-year 6 Li burnup in 6 Li 4 SiO 4 inside the SlimCS DEMO. Crystalline Li 4 SiO 4 phase was not observed in the irradiated depth region of all the samples in this study. In spite of full amorphization in the near-surface region, Li 2 SiO 3 irradiated to a high dose at 773 K remained crystalline in the damage peak region, suggesting that Li 2 SiO 3 is more irradiation resistant to amorphization than Li 4 SiO 4 . Radiolysis may be primarily responsible for silicate decomposition and amorphization. Data from this study also show that D release from the pellet is very efficient during ion irradiation at 773 K, which is accompanied with a significant Li loss. Thermal annealing for 10 min at 773 K for the room-temperature irradiated pellet leads to a nearly complete D release without an observable Li loss. A concept of Ni coating on tritium breeder materials is discussed with supporting data to minimize Li loss without a significant impact on tritium diffusion and release.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Porosity, swelling, and composition evolution in high-burnup monolithic U-Mo fuel

The microstructural progression of very high-burnup (>8 × 10 21 fissions/cm 3 ) monolithic uranium-molybdenum (U-10wt.%Mo) was analyzed, providing crucial insights into the behavior of post-recrystallized nuclear fuel, where scant data exists. Three focused ion beam cuboids sourced from a fuel plate with varying local burnups of 8.86 × 10 21 , 9.05 × 10 21 , and 9.36 × 10 21 fissions/cm 3 were characterized. The porosity and composition of the samples were evaluated to characterize the evolution of the microstructure as a function of fission density and different locations on the fuel plate, while simultaneously isolating plate-specific parameters such as Zr diffusion barrier thickness, hot-isostatic-pressing conditions, enrichment, and reactor conditions. The porosity was segmented, and the three-dimensional distribution of the porosity was extrapolated from the two-dimensional segmentation. The composition was assessed and quantified using energy-dispersive X-ray spectroscopy areal mapping. The porosity fraction increased as a function of the burnup from 27.77±0.51, 35.12±1.54, and 37.71±0.44 % for 8.86 × 10 21 , 9.05 × 10 21 , and 9.36 × 10 21 fissions/cm 3 , respectively. When compared to literature, the porosity volume fraction plateaus at burnups greater than 6 × 10 21 fissions/cm 3 , while the pore size grows linearly as a function of fission density. The number of large pores increased in number density as a function of burnup, while the smallest pores (<0.3 µm) increased up to 9.05 × 10 21 fissions/cm 3 , followed by a decrease at 9.36 × 10 21 fissions/cm 3 . The delamination and cracking in the fuel plate propagated through an interconnected porosity sublayer identified ∼5 µm from the diffusion barrier. The local swelling of the specimens was within or near the prediction bounds of the Robinson-Williams model for local swelling. The fission products, strontium, barium, cerium, and cesium, precipitated into the pores, while neodymium accumulated adjacent to the pores. Furthermore, these findings have direct implications for the development of fuel performance codes and the accurate documentation of the microstructure evolution in high burnup U-Mo, thus enhancing the safety and efficiency of nuclear fuel usage.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Micro-tensile testing of neutron-irradiated Al/Zr and Zr/U-Mo diffusion bonds

This study focuses on micro-tensile testing of neutron-irradiated Al/Zr and Zr/U-Mo diffusion bonds, which are integral to the structure and performance of nuclear fuel plates used in the fuel being developed for U.S. high-power research reactors. During fabrication, two distinct diffusion bonds occur—one at the Zr/U-10Mo interface via roll bonding, and the Zr/Al interface via hot isostatic pressing at 833 K. This work utilizes micro-tensile testing specimens approximately 7 × 7 × 18 μm 3 , which are sufficiently large to encompass the identified diffusion zones to evaluate the failure strength and identify the failure location. For the Zr/Al interface, all failures occurred in the bulk aluminum. The average yield strength, ultimate strength, and strain at failure for the two parent samples were: 125 ± 10 MPa, 139 ± 24 MPa, 156 ± 21 MPa, 185 ± 14 MPa, 37.9 ± 5.6 %, and 29.7 ± 3.4 %, respectively. For specimens across the Zr/U-Mo interface, failures occurred either in the bulk Zr or U-Mo, with no failures observed in the diffusion region. For specimens that failed in the bulk Zr the failure strength and strain for the two parent samples were 570 MPa, 710 ± 131 MPa, and 43.3 %, 27.3 ± 6.6 % respectively. The specimens that failed in the bulk U-Mo had failure strengths and strains of 596 ± 32 MPa, 548 ± 124 MPa, and 2.2 ± 1.3 %, 1.5 ± 0.6 % respectively. In conclusion, these findings support the development of accurate thermo-mechanical models for irradiated fuel performance by identifying the mechanical limits and failure locations within the bonded regions.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Electrical characterization and water sensitivity of Sr 2 Fe 1.5 Mo 0.5 O 6-δ as a possible solid oxide fuel cell electrode

Sr 2 Fe 1.5 Mo 0.5 O 6-δ (SFMO) powders were synthesized by combustion synthesis. Porous samples were formed by uniaxial pressing of powder compacts and sintering in air. Electrical conductivity was measured by a four-point DC technique over a temperature range from 200 °C to 800 °C in air and in hydrogen. Crystal structures were investigated by X-ray diffractometry. Stability of powder samples was investigated in H 2 O-containing atmospheres. It was observed that Sr 2 Fe 1.5 Mo 0.5 O 6-δ was stable at 800 °C in water-containing atmospheres. However, it reacts with water at low temperatures. Reaction of Sr 2 Fe 1.5 Mo 0.5 O 6-δ (SFMO) with water at low temperatures is a potential shortcoming of this material for application in solid oxide fuel cells (SOFC) due to concerns regarding degradation of the electrodes at low temperatures during cycling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Characterizing the Li–Li 7 La 3 Zr 2 O 12 interface stability and kinetics as a function of temperature and current density

The stability and kinetics of the Li–Li 7 La 3 Zr 2 O 12 (LLZO) interface were characterized as a function of temperature and current density. Polycrystalline LLZO was densified using a rapid hot-pressing technique achieving 97 ± 1% relative density, and <10% grain boundary resistance; effectively consisting of an ensemble of single LLZO crystals. It was determined that by heating to 175 °C, the room temperature Li-LLZO interface resistance decreases dramatically from 5822 (as-assembled) to 514 Ω cm 2 ; a > 10-fold decrease. In characterizing the maximum sustainable current density (or critical current density – CCD) of the Li-LLZO interface, several signs of degradation were observed. In DC cycling tests, significant deviation from Ohmic behavior was observed. In post-cycling tests, regions of metallic Li were observed; propagating parallel to the ionic current. For the cells cycled at 30, 70, 100, 130 and 160 °C, the CCD was determined to be 50, 200, 800, 3500, and 20000 μA cm –2 , respectively. As a result, the relationships and phenomena observed in this work can be used to better understand the Li-LLZO interface stability, enabling the use of batteries employing Li metal anodes.

36 MATERIALS SCIENCE↗

Facile and scalable fabrication of polymer-ceramic composite electrolyte with high ceramic loadings

Solid state electrolytes are a promising alternative to flammable liquid electrolytes for high-energy lithium battery applications. In this work polymer-ceramic composite electrolyte membrane with high ceramic loading (greater than 60 vol%) is fabricated using a model polymer electrolyte poly(ethylene oxide) + lithium trifluoromethane sulfonate and a lithium-conducting ceramic powder. The effects of processing methods, choice of plasticizer and varying composition on ionic conductivity of the composite electrolyte are thoroughly investigated. The physical, structural and thermal properties of the composites are exhaustively characterized. We demonstrate that aqueous spray coating followed by hot pressing is a scalable and inexpensive technique to obtain composite membranes that are amazingly dense and uniform. The ionic conductivity of composites fabricated using this protocol is at least one order of magnitude higher than those made by dry milling and solution casting. The introduction of tetraethylene glycol dimethyl ether further increases the ionic conductivity. The composite electrolyte's interfacial compatibility with metallic lithium and good cyclability is verified by constructing lithium symmetrical cells. As a result, a remarkable Li + transference number of 0.79 is discovered for the composite electrolyte.

36 MATERIALS SCIENCE↗