Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Optical Microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88
All sourcesNASA NTRSDOE OSTI
DOE OSTI2015

Assessment of retrogression and re-aging treatment on microstructural and mechanical properties of Al-Zn-Mg-Cu P/M alloy

In order to understand the importance of the retrogression and re-aging as a heat treatment for improving microstructural and mechanical properties of the Al-Zn-Mg-Cu powder metallurgy alloys, Al-Zn-Mg-Cu-Fe-Cr alloys were fabricated from the elemental powders. Green compacts are compressed under compaction pressure about 370 MPa. The sintering process carried out for the samples of aluminum alloys at temperature was 650°C under argon atmosphere for two hours. The sintered compacts were subjected into homogenizing condition at 470°C for 1.5 hours and then aged at 120°C for 24 hours (T6 temper) after that it carried out the retrogressed at 180°C for 30 min., and then re-aged at 120°C for 24 hours (RRA). Observations microstructures were examined using optical, scanning electron microscopy coupled with energy dispersive spectroscopy and X-ray diffraction. Density and porosity content was conducted for the samples of alloys. The result showing that the highest Vickers hardness exhibited for an Al-Zn-Mg-Cu alloy after underwent the retrogression and reaging treatment. Increasing in hardness was because of the precipitation hardening through precipitate the (Mg Zn) and (Mg{sub 2}Zn{sub 11}) phases during matrix of aluminum-alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Effect of ion-beam treatment on structure and fracture resistance of 12Cr1MoV steel under static, cyclic and dynamic loading

Features of the structure and properties modification of 12Cr1MoV steel subjected to irradiation by zirconium ion beam have been investigated with the use of optical and electron microscopy as well as microhardness measurement. It has been shown that upon treatment the structure modification occurred across the entire cross-section of specimens with the thickness of 1 mm. Changes in the mechanical properties of these specimens under static, cyclic and impact loading are interpreted in terms of identified structure changes.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Thermally driven smoothening of molecular thin films: Structural transitions in n-alkane layers studied in real-time

We use thermal annealing to improve smoothness and to increase the lateral size of crystalline islands of n-tetratetracontane (TTC, C{sub 44}H{sub 90}) films. With in situ x-ray diffraction, we find an optimum temperature range leading to improved texture and crystallinity while avoiding an irreversible phase transition that reduces crystallinity again. We employ real-time optical phase contrast microscopy with sub-nm height resolution to track the diffusion of TTC across monomolecular step edges which causes the unusual smoothing of a molecular thin film during annealing. We show that the lateral island sizes increase by more than one order of magnitude from 0.5 μm to 10 μm. This desirable behavior of 2d-Ostwald ripening and smoothing is in contrast to many other organic molecular films where annealing leads to dewetting, roughening, and a pronounced 3d morphology. We rationalize the smoothing behavior with the highly anisotropic attachment energies and low surface energies for TTC. The results are technically relevant for the use of TTC as passivation layer and as gate dielectric in organic field effect transistors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2016

Tunnelling anisotropic magnetoresistance at La{sub 0.67}Sr{sub 0.33}MnO{sub 3}-graphene interfaces

Using ferromagnetic La{sub 0.67}Sr{sub 0.33}MnO{sub 3} electrodes bridged by single-layer graphene, we observe magnetoresistive changes of ∼32–35 MΩ at 5 K. Magneto-optical Kerr effect microscopy at the same temperature reveals that the magnetoresistance arises from in-plane reorientations of electrode magnetization, evidencing tunnelling anisotropic magnetoresistance at the La{sub 0.67}Sr{sub 0.33}MnO{sub 3}-graphene interfaces. Large resistance switching without spin transport through the non-magnetic channel could be attractive for graphene-based magnetic-sensing applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2012

Images reveal that atmospheric particles can undergo liquid-liquid phase separations

A large fraction of submicron atmospheric particles contains both organic material and inorganic salts. As the relative humidity cycles in the atmosphere, these mixed particles can undergo a range of phase transitions, possibly including liquid-liquid phase separation. If liquid-liquid phase separation occurs, the gas-particle partitioning of atmospheric semi-volatile organic compounds, the scattering and absorption of solar radiation, and the uptake of reactive gas species on atmospheric particles will be affected, with important implications for climate predictions. The actual occurrence of these types of phase transitions within individual atmospheric particles has been considered uncertain, in large part because of the absence of observations for real-world samples. Here, using optical and fluorescence microscopy, we observe the coexistence of two non-crystalline phases in particles generated from real-world samples collected on multiple days in Atlanta, Georgia, and in particles generated in the laboratory using atmospheric conditions. These results reveal that atmospheric particles can undergo liquid-liquid phase separations. Using a box model, we show that liquid-liquid phase separation can result in increased concentrations of gas-phase NO3 and N2O5 in the Atlanta region, due to decreased particle uptake of N2O5.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2013

Exhaust Gas Recirculation Cooler Fouling in Diesel Applications: Fundamental Studies Deposit Properties and Microstructure

This paper reports on the results of experimental efforts aimed at improving the understanding of the mechanisms and conditions at play in the fouling of EGR coolers. An experimental apparatus was constructed to utilize simplified surrogate heat exchanger tubes in lieu of full-size heat exchangers. The use of these surrogate tubes allowed removal of the tubes after exposure to engine exhaust for study of the deposit layer and its properties. The exhaust used for fouling the surrogate tubes was produced using a modern medium-duty diesel engine fueled with both ultra-low sulfur diesel and biodiesel blends. At long exposure times, no significant difference in the fouling rate was observed between fuel types and HC levels. Surface coatings for the tubes were also evaluated to determine their impact on deposit growth. No surface treatment or coating produced a reduction in the fouling rate or any evidence of deposit removal. In addition, microstructural analysis of the fouling layers was performed using optical and electron microscopy in order to better understand the deposition mechanism. The experimental results are consistent with thermophoretic deposition for deposit formation, and van der Waals attraction between the deposit surface and exhaust-borne particulate.

EGR↗
DOE OSTI2024

Heat affected zone liquation cracking evaluation on FeMnAl alloys

FeMnAl steels are currently generating a lot of interest with potential applications for structural parts in armored vehicles due to their lower density and outstanding mechanical properties. Despite the extensive mechanical performance and heat treatment exploration of this alloy class, further weldability investigation is required for future large-scale deployment. In the present study, the liquation cracking of four heats of cast FeMnAl alloys was investigated by the spot-Varestraint technique. The study focuses primarily on the effect of the major elements of the FeMnAl system: C, Mn and Al. Optical and electron microscopy were employed to investigate the microstructural features, and CALPHAD was employed to aid the discussion regarding the alloy’s composition differences and their effect on the liquation cracking susceptibility. The study was able to identify that compositions with the higher Mn, C, and lower Al presented the highest liquation cracking susceptibility. Conversely, composition presenting lower Mn, C, and Al showed the most resistant behavior. Furthermore, lower Al content promoted a fully-γ microstructure at low temperatures, which encouraged the appearance of longer cracks as a γ-matrix is more susceptible to HAZ cracking than a fully ferritic (α) or duplex (α + γ) microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Quantization of surface charge density on hyperboloidal and paraboloidal domains with application to plasmon decay rate on nanoprobes

We report that field quantization in high curvature geometries help understanding the elastic and inelastic scattering of photons and electrons in nanostructures and probelike metallic domains. The results find important applications in high-resolution photonic and electronic modalities of scanning probe microscopy, nano-optics, plasmonics, and quantum sensing. We present a calculation of relevant photon interactions in both hyperboloidal and paraboloidal material domains. The two morphologies are compared for their plasmon dispersion properties, field distributions, and radiative decay rates, which are shown to be consistent with the corresponding quantities for the finite prolate spheroidal domains. Finally, the results are relevant to other material domains that model a nanostructure such as a probe tip, quantum dot, or nanoantenna.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

La 2 ⁢O 3 ⁢Mn 2 ⁢Se 2 : A correlated insulating layered d-wave altermagnet

Altermagnets represent a new class of magnetic phases without net magnetization, invariant under a combination of rotation and time reversal. Unlike conventional collinear antiferromagnets (AFM), altermagnets could lead to new correlated states and important material properties deriving from their nonrelativistic spin-split band structure. Indeed, they serve as the magnetic analogue of unconventional superconductors and can yield spin-polarized electrical currents in the absence of external magnetic fields, making them promising candidates for next-generation spintronics. Here, we report altermagnetism in the correlated insulator, magnetically ordered tetragonal oxychalcogenide, L⁢a 2 ⁢O 3⁢ M⁢n 2 ⁢S⁢e 2 . Symmetry analysis reveals a 𝑑 𝑥 2 −𝑦 2 -wave-like spin-momentum locking arising from the M⁢n 2 ⁢O Lieb lattice, supported by density functional theory (DFT) calculations. Magnetic measurements confirm the AFM transition below ∼166K while neutron pair distribution function analysis reveals a 2D short-range magnetic order that persists above the Néel temperature. Single crystals are grown and characterized using x-ray diffraction, optical and electron microscopy, and micro-Raman spectroscopy to confirm the crystal structure, stoichiometry, and uniformity. Furthermore, our findings establish L⁢a 2⁢ O 3 ⁢M⁢n 2⁢ S⁢e 2 as a model altermagnetic system realized on a Lieb lattice.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Three-dimensional coherent X-ray diffractive imaging of whole frozen-hydrated cells

Here, a structural understanding of whole cells in three dimensions at high spatial resolution remains a significant challenge and, in the case of X-rays, has been limited by radiation damage. By alleviating this limitation, cryogenic coherent diffractive imaging (cryo-CDI) can in principle be used to bridge the important resolution gap between optical and electron microscopy in bio-imaging. Here, the first experimental demonstration of cryo-CDI for quantitative three-dimensional imaging of whole frozen-hydrated cells using 8 Kev X-rays is reported. As a proof of principle, a tilt series of 72 diffraction patterns was collected from a frozen-hydrated Neospora caninum cell and the three-dimensional mass density of the cell was reconstructed and quantified based on its natural contrast. This three-dimensional reconstruction reveals the surface and internal morphology of the cell, including its complex polarized sub-cellular structure. Finally, it is believed that this work represents an experimental milestone towards routine quantitative three-dimensional imaging of whole cells in their natural state with spatial resolutions in the tens of nanometres.

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2022

Development of Fixtures and Methods to Assess the Durability of Balance of Systems Components

The degradation of photovoltaic (PV) balance of systems (BoS) components is not well studied, but the consequences include offline modules, strings, and inverters; system shutdown; arc faults; and fires. A utility provider experienced a ~30% failure rate in their power transfer chain, originally attributed to branch connectors. Field-failed specimen assemblies were, therefore, examined, consisting of cable connector, branch connector, and discrete fuse components. In this study, unused field-vintage specimens are examined using a benchtop prototype fixture to identify the most influential environmental stressors on BoS components as well as the effect of external mechanical perturbation. The prototype fixture was used to develop a perturbation capability for future use in the combined-accelerated stress testing chamber. The benchtop experiments were also used to develop the in-situ data acquisition of specimen current, voltage, and temperature. A significant increase in operating temperature (~100 °C from ~40 °C) and a different failure mode (arcing at the metal pins rather than overheating of the fuse filament) were observed promptly once periodic mechanical perturbation was applied. The current at failure was decreased from 35 A (measured for static specimens, with failure occurring in the fuses) to 15 A (for tests with mechanical perturbation, with failure at the male/female metal pin connection). After initial examination using X-ray computed tomography, the external plastic was machined away from failed specimens to allow for failure analysis, including the extraction of the internal convolute springs for morphological examination (optical and electron microscopy). Chemical composition analysis included energy-dispersive X-ray spectroscopy, differential scanning calorimetry, and Fourier transform infrared spectroscopy.

14 SOLAR ENERGY↗
DOE OSTI2022

Evaluating the Durability of Balance of Systems Components Using Combined-Accelerated Stress Testing

The degradation of photovoltaic (PV) balance of systems (BoS) components is not well-studied, but the consequences include offline modules, strings, and inverters; system shutdown; arc faults; and fires. A utility provider experienced a ~30% failure rate in their power transfer chain, originally attributed to branch connectors. Field-failed specimen assemblies were therefore examined, consisting of cable connector, branch connector, and discrete fuse components. In this study, unused field-vintage specimens are examined using combined-accelerated stress testing (C-AST) to clarify the most influential environmental stressors as well as the effect of external mechanical perturbation. A benchtop prototype fixture was used to develop the perturbation capability for the C-AST chamber. The benchtop experiments were also used to develop the in-situ data acquisition of specimen current, voltage, and temperature. A significant increase in operating temperature (~100 degrees C from ~40 degrees C) and a different failure mode were observed promptly once periodic mechanical perturbation was applied. The current at failure was decreased from 35 A (with failure in the fuses) to 15 A (failure at the male/female metal pin connection). After initial examination using X-ray computed tomography, the external plastic was machined away from failed specimens to allow for failure analysis, including the extraction of the internal convolute springs for morphological examination (optical and electron microscopy).

balance of systems↗
DOE OSTI2019

Steam pressure and velocity effects on high temperature silicon carbide oxidation

The effects of steam pressure, velocity, and composition on SiC oxidation kinetics were studied. Pressure effects were tested at 1200°C from 0.1 to 1.4 MPa at a steam velocity of 0.25 cm/s. Velocity effects were tested in two furnaces at 0.45 MPa, 1200°C and 0.1 MPa, 1600°C with velocities ranging from 0.25 to 137 cm/s. Steam composition was altered by changing the reaction vessel material. Oxide morphology and composition were determined using optical and electron microscopy, and X-ray diffraction. Porous oxides were observed whenever structural SiC from the reaction vessel saturated the steam with volatilized silica, H2, and CO. Oxidation kinetics were calculated by the change in SiC thickness. The steam velocity/recession rate followed a power-law relationship of ~ 0.35 while the steam pressure/recession rate followed a power-law relationship of ~ 1.78.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Application of X-ray microcomputed tomography in the characterization of irradiated nuclear fuel and material specimens

X-ray microcomputed tomography (µCT) was applied in characterizing the internal structures of a number of irradiated materials, including carbon-carbon fibre composites, nuclear-grade graphite and tristructural isotropic-coated fuel particles. Local cracks in carbon-carbon fibre composites associated with their synthesis process were observed with µCT without any destructive sample preparation. Pore analysis of graphite samples was performed quantitatively, and qualitative analysis of pore distribution was accomplished. It was also shown that high-resolution µCT can be used to probe internal layer defects of tristructural isotropic-coated fuel particles to elucidate the resulting high release of radioisotopes. Layer defects of sizes ranging from 1 to 5 µm and up could be isolated by to-mography. As an added advantage, µCT could also be used to identify regions with high densities of radioisotopes to deter-mine the proper plane and orientation of particle mounting for further analytical characterization, such as materialographic sectioning followed by optical and electron microscopy. Lastly, in fully ceramic matrix fuel forms, despite the highly absorbing matrix, characterization of tristructural isotropic-coated particles embedded in a silicon carbide matrix was accomplished usingµCT and related advanced image analysis techniques.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Conformal Pressure and Fast-Charging Li-Ion Batteries

Batteries capable of extreme fast-charging (XFC) are a necessity for the deployment of electric vehicles. Material properties of electrodes and electrolytes along with cell parameters such as stack pressure and temperature have coupled, synergistic, and sometimes deleterious effects on fast-charging performance. We develop a new experimental testbed that allows precise and conformal application of electrode stack pressure. We focus on cell capacity degradation using single-layer pouch cells with graphite anodes, LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC532) cathodes, and carbonate-based electrolyte. In the tested range (10–125 psi), cells cycled at higher pressure show higher capacity and less capacity fading. Additionally, Li plating decreases with increasing pressure as observed with scanning electron microscopy (SEM) and optical imaging. While the loss of Li inventory from Li plating is the largest contributor to capacity fade, electrochemical and SEM examination of the NMC cathodes after XFC experiments show increased secondary particle damage at lower pressure. We infer that the better performance at higher pressure is due to more homogeneous reactions of active materials across the electrode and less polarization through the electrode thickness. Our study emphasizes the importance of electrode stack pressure in XFC batteries and highlights its subtle role in cell conditions.

25 ENERGY STORAGE↗
DOE OSTI2021

Pore characterization of the Marcellus Shale by nitrogen adsorption and prediction of its gas storage capacity

In a shale gas reservoir, pore characterization is an important factor used to determine gas storage capacity. However, the nanometer (nm)-scale pore system in shale is difficult to explore by traditional optical, scanning electron microscopy, or even nuclear magnetic resonance well logging. We have investigated the pore structure and storage capacity of the Marcellus Shale through integration of petrophysical analysis from laboratory and well-logging data and nitrogen adsorption. The isotherm of Marcellus Shale is a composite isotherm, which has features of type I, type II, and type IV isotherms with type H4 of the hysteresis loop, suggesting slit-like pores developed in the Marcellus Shale. Quantitative analysis of pore volumes from the nitrogen adsorption indicates that density porosity may be more properly used to approximate the shale porosity and estimate the shale gas volume. In addition, the specific surface area, micropore, and mesopore volumes have a positive relationship with the kerogen volume and total organic content (TOC). By using the Langmuir and Brunauer-Emmet-Teller models, the simulated result indicates that the higher adsorbed quantity of the Marcellus Shale could be the result of the increase of micropore volume contributed, by the increase of kerogen or TOC content. The proposed equations rapidly compute TOC, a key parameter to predict gas storage capacity in overmature shale such as the Marcellus Shale.

Geochemistry & Geophysics↗
DOE OSTI2012

Development and calibration of mirrors and gratings for the Soft X-ray materials science beamline at the Linac Coherent Light Source free-electron laser

This article discusses the development and calibration of the x-ray reflective and diffractive elements for the Soft X-ray Materials Science (SXR) beamline of the Linac Coherent Light Source (LCLS) free-electron laser (FEL), designed for operation in the 500 – 2000 eV region. The surface topography of three Si mirror substrates and two Si diffraction grating substrates was examined by atomic force microscopy (AFM) and optical profilometry. The figure of the mirror substrates was also verified via surface slope measurements with a long trace profiler. A boron carbide (B 4 C) coating especially optimized for the LCLS FEL conditions was deposited on all SXR mirrors and gratings. Coating thickness uniformity of 0.14 nm root mean square (rms) across clear apertures extending to 205 mm length was demonstrated for all elements, as required to preserve the coherent wavefront of the LCLS source. The reflective performance of the mirrors and the diffraction efficiency of the gratings were calibrated at beamline 6.3.2 at the Advanced Light Source synchrotron. To verify the integrity of the nanometer-scale grating structure, the grating topography was examined by AFM before and after coating. This is to our knowledge the first time B 4 C-coated diffraction gratings are demonstrated for operation in the soft x-ray region.

36 MATERIALS SCIENCE↗