Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Membrane systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Experimentally Determined Overall Heat Transfer Coefficients for Spacesuit Liquid Cooled Garments

A Human-In-The-Loop (HITL) Portable Life Support System 2.0 (PLSS 2.0) test has been conducted at NASA Johnson Space Center in the PLSS Development Laboratory from October 27, 2014 to December 19, 2014. These closed-loop tests of the PLSS 2.0 system integrated with human subjects in the Mark III Suit at 3.7 psi to 4.3 psi above ambient pressure performing treadmill exercise at various metabolic rates from standing rest to 3000 BTU/hr (880 W). The bulk of the PLSS 2.0 was at ambient pressure but effluent water vapor from the Spacesuit Water Membrane Evaporator (SWME) and the Auxiliary Membrane Evaporator (Mini-ME), and effluent carbon dioxide from the Rapid Cycle Amine (RCA) were ported to vacuum to test performance of these components in flight-like conditions. One of the objectives of this test was to determine the overall heat transfer coefficient (UA) of the Liquid Cooling Garment (LCG). The UA, an important factor for modeling the heat rejection of an LCG, was determined in a variety of conditions by varying inlet water temperature, flow rate, and metabolic rate. Three LCG configurations were tested: the Extravehicular Mobility Unit (EMU) LCG, the Oceaneering Space Systems (OSS) LCG, and the OSS auxiliary LCG. Other factors influencing accurate UA determination, such as overall heat balance, LCG fit, and the skin temperature measurement, will also be discussed.

Bue, Grant↗
DOE OSTI2025

Fuel cells for single-aisle regional aircraft: System configuration, performance and cost

A hydrogen fuel cell propelled electric aircraft can compete with incumbent turbofan technologies for single-aisle regional aircraft by coupling design of stack, air handling, thermal management, propulsion, and airframe to optimize performance. The stack operates at 95°C to facilitate heat rejection during take-off and below 75°C during cruise to extend lifetime and is oversized to satisfy power requirements at end of life. A multi-stage turbocompressor with a compression ratio >10 is selected to reach high stack power density at 11,300-m cruise altitude. The propulsion system is configured to accommodate air handling within the core duct, an inclined heat exchanger in the outer duct to limit the nacelle size, and variable area nozzles to independently control mass flows through the core and bypass ducts. The airframe is modified for maximum lift coefficient and longer balanced field length for dramatically reduced thrust during take-off, and the fuselage is stretched by 20% to store liquid hydrogen (LH 2 ). Modularization of power systems promotes safety in one engine inoperative scenarios and allows reaching specific power metrics for stack, balance-of-plant and fuel cell system (FCS), necessary for acceptable take-off weight. In conclusion, cost parity requires increase in FCS lifetime, LH 2 cost reduction, and improved FCS specific power.

Catalyst durability↗
DOE OSTI2021

Vibronic coupling in light-harvesting complex II revisited

A growing body of work has pointed to vibronic mixing as a crucial design principle for efficient energy and charge transfer in natural and artificial systems.= Notable among these studies was the recent observation of vibronically promoted ultrafast energy flow in the major antenna complex of green plants and algae light-harvesting complex II (LHCII)—the most abundant membrane protein on the Earth—via the emerging experimental technique two-dimensional electronic-vibrational (2DEV) spectroscopy. This spectroscopy, which correlates electronic and nuclear degrees-of-freedom, shows promise for providing mechanistic insight into vibronic coupling; however, explicit theoretical input is necessary to extract such a detail. In a separate paper, we have developed a heterodimer model that describes various forms of vibronic coupling—which were speculated to be present in LHCII—resulting from diagonal electron–phonon coupling giving Franck–Condon (FC) activity and the nuclear dependence of the electronic transition dipole moment giving Herzberg–Teller (HT) activity. Here, we draw connections between this theoretical work and recent experimental studies in order to demonstrate how HT activity is leveraged in the function of LHCII.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Enhanced Energy Transfer to an Optomechanical Piston from Indistinguishable Photons

Thought experiments involving gases and pistons, such as Maxwell’s demon and Gibbs’ mixing, are central to our understanding of thermodynamics. In this paper, we present a quantum thermodynamic thought experiment in which the energy transfer from two photonic gases to a piston membrane grows quadratically with the number of photons for indistinguishable gases, while it grows linearly for distinguishable gases. This signature of bosonic bunching may be observed in optomechanical experiments, highlighting the potential of these systems for the realization of thermodynamic thought experiments in the quantum realm.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS2000

Modeling and Analysis of the Reverse Water Gas Shift Process for In-Situ Propellant Production

This report focuses on the development of mathematical models and simulation tools developed for the Reverse Water Gas Shift (RWGS) process. This process is a candidate technology for oxygen production on Mars under the In-Situ Propellant Production (ISPP) project. An analysis of the RWGS process was performed using a material balance for the system. The material balance is very complex due to the downstream separations and subsequent recycle inherent with the process. A numerical simulation was developed for the RWGS process to provide a tool for analysis and optimization of experimental hardware, which will be constructed later this year at Kennedy Space Center (KSC). Attempts to solve the material balance for the system, which can be defined by 27 nonlinear equations, initially failed. A convergence scheme was developed which led to successful solution of the material balance, however the simplified equations used for the gas separation membrane were found insufficient. Additional more rigorous models were successfully developed and solved for the membrane separation. Sample results from these models are included in this report, with recommendations for experimental work needed for model validation.

Whitlow, Jonathan E.↗
NASA NTRS2000

CHO cell enlargement oscillates with a temperature-compensated period of 24 min

The rate of increase in cell area of CHO cells when measured at intervals of 1 min using a light microscope equipped with a video measurement system, oscillated with a minimum period of about 24 min. The pattern of oscillations paralleled those of the 24 min period observed with the oxidation of NADH by an external cell surface or plasma membrane NADH oxidase. The increase in cell area was non-linear. Intervals of rapid increase in area alternated with intervals of rapid decrease in area. The length of the 24 min period was temperature-compensated (approximately the same when measured at 14 degrees C, 24 degrees C or 34 degrees C) while the rate of cell enlargement increased with temperature over this same range of temperatures.

Non-NASA Center↗
NASA NTRS2004

Emerging Fuel Cell Technology Being Developed: Offers Many Benefits to Air Vehicles

Fuel cells, which have recently received considerable attention for terrestrial applications ranging from automobiles to stationary power generation, may enable new aerospace missions as well as offer fuel savings, quiet operations, and reduced emissions for current and future aircraft. NASA has extensive experience with fuel cells, having used them on manned space flight systems over four decades. Consequently, the NASA Glenn Research Center has initiated an effort to investigate and develop fuel cell technologies for multiple aerospace applications. Two promising fuel cell types are the proton exchange membrane (PEM) and solid oxide fuel cell (SOFC). PEM technology, first used on the Gemini spacecraft in the sixties, remained unutilized thereafter until the automotive industry recently recognized the potential. PEM fuel cells are low-temperature devices offering quick startup time but requiring relatively pure hydrogen fuel. In contrast, SOFCs operate at high temperatures and tolerate higher levels of impurities. This flexibility allows SOFCs to use hydrocarbon fuels, which is an important factor considering our current liquid petroleum infrastructure. However, depending on the specific application, either PEM or SOFC can be attractive. As only NASA can, the Agency is pursuing fuel cell technology for civil uninhabited aerial vehicles (UAVs) because it offers enhanced scientific capabilities, including enabling highaltitude, long-endurance missions. The NASA Helios aircraft demonstrated altitudes approaching 100,000 ft using solar power in 2001, and future plans include the development of a regenerative PEM fuel cell to provide nighttime power. Unique to NASA's mission, the high-altitude aircraft application requires the PEM fuel cell to operate on pure oxygen, instead of the air typical of terrestrial applications.

Walker, James F.↗
DOE OSTI2021

Biological and algae harvesting and cultivation systems and methods

Algae harvesting and cultivating systems and methods for producing high concentrations of algae product with minimal energy. In an embodiment, an algae harvesting method is provided for performing dead-end filtration in an algae harvesting system having at least one treatment tank defining a plurality of filtration stages including at least a first filtration stage and a second filtration stage. An algae medium is pulled through the hollow fiber membranes such that a retentate and a permeate are produced.

Hazlebeck, David A.↗
NASA NTRS2011

Energy Storage Project

NASA's Exploration Technology Development Program funded the Energy Storage Project to develop battery and fuel cell technology to meet the expected energy storage needs of the Constellation Program for human exploration. Technology needs were determined by architecture studies and risk assessments conducted by the Constellation Program, focused on a mission for a long-duration lunar outpost. Critical energy storage needs were identified as batteries for EVA suits, surface mobility systems, and a lander ascent stage; fuel cells for the lander and mobility systems; and a regenerative fuel cell for surface power. To address these needs, the Energy Storage Project developed advanced lithium-ion battery technology, targeting cell-level safety and very high specific energy and energy density. Key accomplishments include the development of silicon composite anodes, lithiated-mixed-metal-oxide cathodes, low-flammability electrolytes, and cell-incorporated safety devices that promise to substantially improve battery performance while providing a high level of safety. The project also developed "non-flow-through" proton-exchange-membrane fuel cell stacks. The primary advantage of this technology set is the reduction of ancillary parts in the balance-of-plant--fewer pumps, separators and related components should result in fewer failure modes and hence a higher probability of achieving very reliable operation, and reduced parasitic power losses enable smaller reactant tanks and therefore systems with lower mass and volume. Key accomplishments include the fabrication and testing of several robust, small-scale nonflow-through fuel cell stacks that have demonstrated proof-of-concept. This report summarizes the project s goals, objectives, technical accomplishments, and risk assessments. A bibliography spanning the life of the project is also included.

Mercer, Carolyn R.↗
DOE OSTI2021

Maturation of Rhodobacter capsulatus Multicopper Oxidase CutO Depends on the CopA Copper Efflux Pathway and Requires the cutF Product (Final Report)

The goal is to achieve a comprehensive understanding of the nature, mechanism of function and biogenesis of c-type cytochromes and their oligomeric complexes. These cytochrome are ubiquitous heme proteins that are required for cellular bioenergetics, including photosynthesis (Ps) and respiration (Res), which are central to chemical energy (ATP) production by oxidative- and photophosphorylation. We contribute to the molecular characterization of individual and membrane-integral cytochromes as parts of Ps and Res electron transport (ET) pathways, using the facultative phototrophic bacteria of as excellent models for multidisciplinary investigations. Supported by this grant we discovered novel membrane-bound cytochromes and cyts c complexes that are important for Ps- and Res-ET. We worked out their biogenesis including maturation (covalent heme addition) and assembly of mature subunits into complexes. These involve fundamental process found virtually in all organisms and are fundamental processes with major significance to the “Photosynthetic Systems” program of DOE-BES, because the cytochromes are integral components of natural energy production systems. Elucidation of basic principles, and the knowledge gained by their study greatly impact on our ability to design, engineer, and create new natural, bio-hybrid, bio-inspired and artificial systems to better capture light, transduce and store its energy with improved efficacy and are of broad significance.

14 SOLAR ENERGY↗
NASA NTRS2000

Solar Power System Evaluated for the Human Exploration of Mars

The electric power system is a crucial element of any mission for the human exploration of the Martian surface. The bulk of the power generated will be delivered to crew life support systems, extravehicular activity suits, robotic vehicles, and predeployed in situ resource utilization (ISRU) equipment. In one mission scenario, before the crew departs for Mars, the ISRU plant operates for 435 days producing liquefied methane and oxygen for ascent-stage propellants and water for crew life support. About 200 days after ISRU production is completed, the crew arrives for a 500-day surface stay. In this scenario, the power system must operate for a total of 1130 days (equivalent to 1100 Martian "sols"), providing 400 MW-hr of energy to the ISRU plant and up to 18 kW of daytime user power. A photovoltaic power-generation system with regenerative fuel cell (RFC) energy storage has been under study at the NASA Glenn Research Center at Lewis Field. The conceptual power system is dominated by the 4000- m2 class photovoltaic array that is deployed orthogonally as four tent structures, each approximately 5 m on a side and 100-m long. The structures are composed of composite members deployed by an articulating mast, an inflatable boom, or rover vehicles, and are subsequently anchored to the ground. Array panels consist of thin polymer membranes with thin-film solar cells. The array is divided into eight independent electrical sections with solar cell strings operating at 600 V. Energy storage is provided by regenerative fuel cells based on hydrogen-oxygen proton exchange membrane technology. Hydrogen and oxygen reactants are stored in gaseous form at 3000 psi, and the water produced is stored at 14.7 psi. The fuel cell operating temperature is maintained by a 40-m2 deployable pumped-fluid loop radiator that uses water as the working fluid. The power management and distribution (PMAD) architecture features eight independent, regulated 600-Vdc channels. Power management and distribution power cables use various gauges of copper conductors with ethylene tetrafluoroethylene insulation. To assess power system design options and sizing, we developed a dedicated Fortran code to predict detailed power system performance and estimate system mass. This code also modeled the requisite Mars surface environments: solar insolation, Sun angles, dust storms, dust deposition, and thermal and ultraviolet radiation. Using this code, trade studies were performed to assess performance and mass sensitivities to power system design parameters (photovoltaic array geometry and orientation) and mission parameters (landing date and landing site latitude, terrain slope, and dust storm activity). Mission analysis cases were also run. Power results are shown in this graph for an analysis case with a September 1, 2012, landing date; 18.95 North latitude landing site; two seasonal dusts storms; and tent arrays. To meet user load requirements and the ISRU energy requirement, an 8-metric ton (MT) power system and 4000-m2 photovoltaic array area were required for the assumed advanced CuInS2 thin-film solar cell technology. In this figure, the top curve is the average daytime photovoltaic array power, the middle curve is average daytime user load power, and the bottom curve is nighttime power. At mission day 1, daytime user power exceeds 120 kW before falling off to 80 kW at the end of the mission. Throughout the mission, nighttime user power is set to the nighttime power requirement. In this analysis, "nighttime" is defined as the 13- to 15-hr period when array power output is below the daytime power requirement. During dust storms, power system capability falls off dramatically so that by mission day 900, a daily energy balance cannot be maintained. Under these conditions, the ISRU plant is placed in standby mode, and the regenerative fuel cell energy storage is gradually discharged to meet user loads.

Kerslake, Thomas W.↗
DOE OSTI2020

The Effect of Membrane Casting Irregularities on Initial Fuel Cell Performance

Membrane electrode assemblies (MEA) for polymer electrolyte membrane fuel cells (PEMFC) may possess as-manufactured non-uniformities in any of its constituent components. This article studies casting irregularities located within the PEM to understand their potential impact on MEA initial performance. Membrane material was cast on a lab-scale polymer casting line operating either within or at the boundaries of the process window. The resulting membrane material was either pristine in the former case, or, in the latter case, contained air bubbles, cracks, and other irregularities, ranging in size from about 0.6 to 3 mm. Spatial polarization experiments were conducted using a 121-channel segmented fuel cell system, and thermal imaging was performed subsequently to map hydrogen crossover to spatial performance. While total-cell polarization data was minimally impacted by the irregularities, the spatial diagnostics showed local performance impacts that, in operation over time, could cause degradation in performance or earlier failure of the MEA. Such impacts could lead to these irregularities being classified as defects, i.e., manufacturing variations that should be identified and not included in a fuel cell stack. Classification of irregularities as defects will ultimately assist the industry by contributing to the development of threshold detection limits for in-line quality control diagnostics.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS1993

The mechanosensory calcium-selective ion channel: key component of a plasmalemmal control centre?

Mechanosensory calcium-selective ion channels probably serve to detect not only mechanical stress but also electrical, thermal, and diverse chemical stimuli. Because all stimuli result in a common output, most notably a shift in second messenger calcium concentration, the channels are presumed to serve as signal integrators. Further, insofar as second messenger calcium in turn gives rise to mechanical, electrical, and diverse chemical changes, the channels are postulated to initiate regulatory feedbacks. It is proposed that the channels and the feedback loops play a wide range of roles in regulating normal plant function, as well as in mediating disturbance of normal function by environmental stressors and various pathogens. In developing evidence for the physiological performance of the channel, a model for a cluster of regulatory plasmalemmal proteins and cytoskeletal elements grouped around a set of wall-to-membrane and transmembrane linkers has proved useful. An illustration of how the model might operate is presented. It is founded on the demonstration that several xenobiotics interfere both with normal channel behaviour and with gravitropic reception. Accordingly, the first part of the illustration deals with how the channels and the control system within which they putatively operate might initiate gravitropism. Assuming that gravitropism is an asymmetric expression of growth, the activities of the channels and the plasmalemmal control system are extrapolated to account for regulation of both rate and allometry of cell expansion. Finally, it is discussed how light, hormones, redox agents and herbicides could in principle affect growth via the putative plasmalemmal control cluster or centre.

NASA Program Space Biology↗
DOE OSTI2025

Frontiers of Ionic Liquids in Carbon Dioxide Separation and Valorization

Ionic liquids (ILs) have emerged as highly tunable sorbents and membranes for gas separation, especially in the purification of CO 2 -containing gas streams such as air, natural gas, biogas, and syngas. Their negligible volatility, high thermal stability, and chemical versatility position them as promising alternatives to conventional amine and alkaline metal derivative-based systems, effectively addressing key challenges such as volatility, stability, and high regeneration energy. Here, this Review explores IL-derived systems for CO 2 -related gas separation across dense, porous, and supported categories. At the dense liquid level, we discuss strategies for tailoring IL properties to optimize CO 2 sorption, focusing on the correlation between IL-CO 2 interaction strength, uptake capacity, and regeneration energy. Key advancements in carbon capture, including amino-functionalized (AILs) and superbase-derived ILs (SILs), are highlighted, along with strategies such as chemical structure engineering, multiple binding site integration, alternative driving force exploration, and stability enhancement. Then, the porous liquids (PLs) scale focuses on the emerging field integrating IL properties with permanent porosity engineering, spanning ultramicropores (<5 Å) to macropores (around 100 nm). These innovations improve gas uptake capacity, accelerate transport kinetics, introduce the gating effect, and enable the coexistence of active sites with antagonistic properties within a single IL medium. At the supported IL scale, the discussion shifts to IL- and ionic pair-modified sorbents and membranes, emphasizing the modulation of cations and anions, confinement effects from porous supports, and the IL–interface interaction to enhance CO 2 separation performance, particularly in diluted gas streams. Beyond separation, this Review highlights IL-based integrated processes for CO 2 capture and conversion into value-added chemicals via thermocatalytic, electrocatalytic, and photocatalytic pathways. At each scale, advanced computational and experimental tools for IL design are also discussed, providing insights into stability enhancement, sorption efficiency, and process integration. The Review concludes by addressing existing challenges and outlining future directions for IL-driven innovations in gas separation technologies.

Qiu, Liqi [Univ. of Tennessee, Knoxville, TN (Unit↗
NASA NTRS2005

Improved Cathode Structure for a Direct Methanol Fuel Cell

An improved cathode structure on a membrane/electrode assembly has been developed for a direct methanol fuel cell, in a continuing effort to realize practical power systems containing such fuel cells. This cathode structure is intended particularly to afford better cell performance at a low airflow rate. A membrane/electrode assembly of the type for which the improved cathode structure was developed (see Figure 1) is fabricated in a process that includes brush painting and spray coating of catalyst layers onto a polymer-electrolyte membrane and onto gas-diffusion backings that also act as current collectors. The aforementioned layers are then dried and hot-pressed together. When completed, the membrane/electrode assembly contains (1) an anode containing a fine metal black of Pt/Ru alloy, (2) a membrane made of Nafion 117 or equivalent (a perfluorosulfonic acid-based hydrophilic, proton-conducting ion-exchange polymer), (3) a cathode structure (in the present case, the improved cathode structure described below), and (4) the electrically conductive gas-diffusion backing layers, which are made of Toray 060(TradeMark)(or equivalent) carbon paper containing between 5 and 6 weight percent of poly(tetrafluoroethylene). The need for an improved cathode structure arises for the following reasons: In the design and operation of a fuel-cell power system, the airflow rate is a critical parameter that determines the overall efficiency, cell voltage, and power density. It is desirable to operate at a low airflow rate in order to obtain thermal and water balance and to minimize the size and mass of the system. The performances of membrane/electrode assemblies of prior design are limited at low airflow rates. Methanol crossover increases the required airflow rate. Hence, one way to reduce the required airflow rate is to reduce the effect of methanol crossover. Improvement of the cathode structure - in particular, addition of hydrophobic particles to the cathode - has been demonstrated to mitigate the effects of crossover and decrease the airflow required.

Valdez, Thomas↗
DOE OSTI2020

Flue Gas CO 2 Capture via Electrochemically Mediated Amine Regeneration: Desorption Unit Design and Analysis

We analyzed the performance of an electrochemical desorption unit to be implemented in an electrochemically mediated amine regeneration (EMAR) process, which separates CO 2 and regenerates the amine upon modulation of a targeted species that complexes with the amine molecules. Using a simplified one-dimensional boundary layer model, we combined the kinetic expressions of the faradaic reactions with mass transfer effects to analyze the polarization behavior of the flow cell. Mass transfer limitations become dominant at high current densities, leading to increases in energy consumption. An understanding of scaling laws with key parameters, such as the Sherwood number, is required to achieve high power operation with minimal mass transfer losses. Because the EMAR chemistry is sensitive to temperature, heat distribution in the unit is also examined. Our results indicate that the desorption performance increases with addition of a high-temperature heat source. Additionally, incorporation of membrane crossover suggests energy losses because of diffusion and migration of active species. Furthermore, these findings inform on scaling laws for at-scale desorber design and provide a model for scaling up the EMAR system for larger scale operations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Separation of Hydrogen Using Pd/Ag Membranes: Experimental and Modeling Results with Potential Application to Direct Internal Recycle

Implementation of fusion energy requires processing the deuterium-tritium (D-T) mixture used to fuel the reaction, and separation of hydrogen isotopes from other gases is imperative. Specifically, the separation of hydrogen isotopes from helium is a matter of importance to the fusion fuel cycle community. Initial testing with a palladium-silver (Pd-Ag) membrane indicates that even moderate vacuum (~100 torr permeate pressure) can provide a high degree of separation (>90%) at a high ratio of H 2 to He. Given the presence of He in many fusion systems, a high technology readiness level (TRL) for Q 2 /He (where Q represents any isotope of hydrogen) separations is needed. This study demonstrates the efficacy of H 2 removal from He via permeation and potential applications for direct internal recycle. Modeling will accompany the experimental campaign to generate a predictive capability and quantify the separation performance. Modeling from previous hydrogen permeation studies has demonstrated that the typical Sieverts’ law fails to predict the measured permeation rates at high hydrogen fluxes. Existing models are being refined to integrate the effects of surface phenomena into permeation predictions, which have been expanded to account for mixtures with large ranges of Q 2 concentrations. These data will improve the TRL of permeators as a separation technology for the fusion fuel cycle.

08 HYDROGEN↗
NASA NTRS1975

Lead-oxygen closed-loop battery system

Calculations show that battery can deliver up to 35 watt-hours per pound, conventional lead-acid batteries deliver 10 to 15 watt-hours per pound. Weight reduction is due to replacement of solid lead-peroxide electrodes with metal current-collector screen, catalyst, and Teflon membrane.

Britz, W. J.↗