Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Matrix Theory”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

High temperature dynamic modulus and damping of aluminum and titanium matrix composites

Dynamic modulus and damping capacity property data were measured from 20 to over 500 C for unidirectional B/Al (1100), B/Al (6061), B/SiC/Al (6061), Al2O3/Al, SiC/Ti-6Al-4V, and SiC/Ti composites. The measurements were made under vacuum by the forced vibration of composite bars at free-free flexural resonance near 2000 Hz and at amplitudes below 0.000001. Whereas little variation was observed in the dynamic moduli of specimens with approximately the same fiber content (50 percent), the damping of B/Al composites was found at all temperatures to be significantly greater than the damping of the Al2O3/Al and SiC/Ti composites. For those few situations where slight deviations from theory were observed, the dynamic data were examined for information concerning microstructural changes induced by composite fabrication and thermal treatment. The 270 C damping peak observed in B/Al (6061) composites after heat treatment above 460 C appears to be the result of a change in the 6061 aluminum alloy microstructure induced by interaction with the boron fibers. The growth characteristics of the damping peak suggest its possible value for monitoring fiber strength degration caused by excess thermal treatment during B/Al (6061) fabrication and use.

Dicarlo, J. A.↗
DOE OSTI2022

Simultaneous stoquasticity

Stoquastic Hamiltonians play a role in the computational complexity of the local Hamiltonian problem as well as the study of classical simulability. In particular, stoquastic Hamiltonians can be straightforwardly simulated using Monte Carlo techniques. We address the question of whether two or more Hamiltonians may be made simultaneously stoquastic via a unitary transformation. This question has important implications for the complexity of simulating quantum annealing where quantum advantage is related to the stoquasticity of the Hamiltonians involved in the anneal. We find that for almost all problems no such unitary exists and show that the problem of determining the existence of such a unitary is equivalent to identifying if there is a solution to a system of polynomial (in)equalities in the matrix elements of the initial and transformed Hamiltonians. Furthermore, solving such a system of equations is NP-hard. We highlight a geometric understanding of this problem in terms of a collection of generalized Bloch vectors.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Quantum simulations of hadron dynamics in the Schwinger model using 112 qubits

Hadron wave packets are prepared and time evolved in the Schwinger model using 112 qubits of IBM’s 133-qubit Heron quantum computer ibm_torino. The initialization of the hadron wave packet is performed in two steps. First, the vacuum is prepared across the whole lattice using the recently developed SC-ADAPT-VQE algorithm and workflow. SC-ADAPT-VQE is then extended to the preparation of localized states, and used to establish a hadron wave packet on top of the vacuum. This is done by adaptively constructing low-depth circuits that maximize the overlap with an adiabatically prepared hadron wave packet. Due to the localized nature of the wavepacket, these circuits can be determined on a sequence of small lattices using classical computers, and then robustly scaled to prepare wave packets on large lattices for simulations using quantum computers. Time evolution is implemented with a second-order Trotterization. To reduce both the required qubit connectivity and circuit depth, an approximate quasilocal interaction is introduced. This approximation is made possible by the emergence of confinement at long distances, and converges exponentially with increasing distance of the interactions. Using multiple error-mitigation strategies, up to 14 Trotter steps of time evolution are performed, employing 13,858 two-qubit gates (with a CNOT depth of 370). The propagation of hadrons is clearly identified, with results that compare favorably with Matrix Product State simulations. Finally, prospects for a near-term quantum advantage in simulations of hadron scattering are discussed.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Scalable quantum simulations of scattering in scalar field theory on 120 qubits

Simulations of collisions of fundamental particles on a quantum computer are expected to have an exponential advantage over classical methods and promise to enhance searches for new physics. Furthermore, scattering in scalar field theory has been shown to be bounded-error quantum polynomial time (BQP) complete, making it a representative problem for which quantum computation is efficient. As a step toward large-scale quantum simulations of collision processes, scattering of wave packets in one-dimensional scalar field theory is simulated using 120 qubits of IBM’s Heron superconducting quantum computer ibm_fez. Variational circuits compressing vacuum preparation, wave packet initialization, and time evolution are determined using classical resources. By leveraging physical properties of states in the theory, such as symmetries and locality, the variational quantum algorithm constructs scalable circuits that can be used to simulate arbitrarily large system sizes. A new strategy is introduced to mitigate errors in quantum simulations, which enables the extraction of meaningful results from circuits with up to 4924 two-qubit gates and two-qubit gate depths of 103. The effect of interactions is clearly seen, and is found to be in agreement with classical matrix product state simulations. Finally, the developments that will be necessary to simulate high-energy inelastic collisions on a quantum computer are discussed.

quantum circuits↗
DOE OSTI2023

The Standard Model Theory of Neutron Beta Decay

We review the status of the Standard Model theory of neutron beta decay. Particular emphasis is put on the recent developments in the electroweak radiative corrections. Given that some existing approaches give slightly different results, we thoroughly review the origin of discrepancies, and provide our recommended value for the radiative correction to the neutron and nuclear decay rates. The use of dispersion relation, lattice Quantum Chromodynamics, and an effective field theory framework allows for high-precision theory calculations at the level of 10 –4 , turning neutron beta decay into a powerful tool to search for new physics, complementary to high-energy collider experiments. We offer an outlook to the future improvements.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Living on the edge: a non-perturbative resolution to the negativity of bulk entropies

Lin, Maldacena, Rozenberg, and Shan (LMRS) presented a new information paradox in black hole physics by noticing that the entanglement and Rényi entropies in a two-sided black hole can become negative when the geometry contains a very large number of matter excitations behind the black hole horizon. While originally this puzzle was presented in the context of BPS two-sided black holes in two-dimensional supergravity, the negativity in fact persists for more general two-sided black holes in the presence of a large number of matter excitations. Since the entanglement and Rényi entropies in ordinary quantum systems cannot be negative, resolving this puzzle is a necessary step towards understanding the quantum mechanical description of black holes. In this paper, we explain how to address the entanglement negativity puzzle, both in the original setting discussed by LMRS and in more general non-supersymmetric settings, by summing over all non-perturbative contributions to the gravitational path integral. We then interpret this result from the point of view of a dual matrix integral, which we use to extend our analysis beyond the regime of validity of the genus re-summation performed in the gravitational path integral. In this regime, positivity is rescued by new saddles of the matrix integral, a one-eigenvalue instanton and a two-eigenvalue instanton. Finally, we formulate a similar puzzle and its resolution using random tensor network techniques.

FOS: Physical sciences↗
NASA NTRS1985

Parametric Stiffness Control of Flexible Structures

An unconventional method for control of flexible space structures using feedback control of certain elements of the stiffness matrix is discussed. The advantage of using this method of configuration control is that it can be accomplished in practical structures by changing the initial stress state in the structure. The initial stress state can be controlled hydraulically or by cables. The method leads, however, to nonlinear control equations. In particular, a long slender truss structure under cable induced initial compression is examined. both analytical and numerical analyses are presented. Nonlinear analysis using center manifold theory and normal form theory is used to determine criteria on the nonlinear control gains for stable or unstable operation. The analysis is made possible by the use of the exact computer algebra system MACSYMA.

Moon, F. C.↗
NASA NTRS1987

A versatile and low order hybrid stress element for general shell geometry

A hybrid stress general shell element is developed based on the Hellinger-Reissner principle modified for relaxed element compatibility conditions. The element is based on a consistent first order thin shell theory with Love Kirchhoff hypotheses. It is of quadrilateral shape with only four corner nodes and five degrees of freedom per node. The geometry of the element is approximated through a bi-cubic polynomial surface patch. Numerical examples consist of torsion-loaded slit cylinder and pinched cylinder with open ends and rigid diaphragmed ends. Also, the representation of the rigid body motion is studied by series of parametric eigenvalue analysis of the stiffness matrix.

Kang, David S.↗
DOE OSTI2024

Effect of parallel flow on resonant layer responses in high beta plasmas

Abstract Resonant layers in a tokamak respond to non-axisymmetric magnetic perturbations by amplifying the mode amplitude and balancing the plasma rotation through magnetic reconnection and force balance, respectively. This resonant response can be characterized by local layer parameters and especially by a single quantity in the linear regime, the so-called inner-layer Δ. The computation of Δ under two-fluid drift-MHD formalism has been progressed by reducing the order of the system in the phase space, where the shielding current is approximated as being only carried by electrons, a posteriori . In this study, we relax the approximation and compute Δ accounted for by the parallel flow associated with the ion shielding current. The posteriori is numerically verified in great agreement with the original SLAYER developed in a previous paper (J.-K. Park 2022 Phys. Plasmas 29 072506). Extending the resonant layer response theory to high β plasmas, our research findings answer two important questions: how the parallel flow influences the resonant layer response and why the parallel flow effect appears in high β plasmas. The complicated plasma compression in high β regime allows the parallel flow response to give rise to the ion shielding current, which not only shifts the zero-crossing condition of the ExB flow but also enhances the field penetration threshold. Technically, the Riccati matrix transformation method is adapted to handle the numerical stiffness due to the increased order of the system. The high fidelity of this numerical method makes use of further extension of the model to higher-order systems to take other physical phenomena into account. This work is envisaged to predict the resonant layer response under high β fusion reactor conditions.

Lee, Yeongsun (ORCID:000000034474416X)↗
DOE OSTI2021

Orbital-resolved calculations of two-center interferences in linear triatomic molecules

In this report we perform ab initio calculations of high-harmonic spectroscopy (HHS) of two-center interference phenomena in oriented carbon-dichalcogen molecules, using time-dependent density functional theory (TDDFT). We show that by resolving the harmonic response into contributions from individual Kohn-Sham orbitals, we can extract target-specific characteristics for both the spectral amplitude and phase. We also discuss that this extraction is predicated on a careful analysis and normalization of the harmonic spectrum. Finally, we present field-free scattering calculations that mimic the recollision step in high-order-harmonic generation and allow the calculation of recombination dipole matrix elements without explicitly calculating the scattering states of a molecule. We show that the orbital-resolved TDDFT HHS results and results based on our field-free scattering calculations are in very good agreement with each other.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Ab initio benchmarks of neutrinoless double- β decay in light nuclei with a chiral Hamiltonian

Here, we report ab initio benchmark calculations of nuclear matrix elements (NMEs) for neutrinoless double-β (0νββ) decays in light nuclei with mass numbers ranging from A = 6 to A = 22. We use the transition operator derived from light-Majorana neutrino exchange and evaluate the NME with three different methods: two variants of in-medium similarity renormalization group (IMSRG) and importance-truncated no-core shell model (IT-NCSM). The same two plus three nucleon interaction from chiral effective field theory is employed, and both isospin-conserving (ΔT = 0) and isospin-changing (ΔT = 2) transitions are studied. We compare our resulting ground-state energies and NMEs to those of recent ab initio no-core shell model and coupled-cluster calculations, also with the same inputs. We show that the NMEs of ΔT = 0 transitions are in good agreement among all calculations, at the level of 10%. For ΔT = 2, relative deviations are more significant in some nuclei. The comparison with the exact IT-NCSM result allows us to analyze these cases in detail, and indicates the next steps toward improving the IMSRG-based approaches. The present study clearly demonstrates the power of consistent cross checks that are made possible by ab initio methodology. This capability is crucial for providing meaningful many-body uncertainties in the NMEs for the 0νββ decays in heavier candidate nuclei, where quasiexact benchmarks are not available.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1988

Influence of convection on microstructure

The influence was studied of convection during directional solidification on the resulting microstructure of eutectics, specifically lead/tin and manganese/bismuth. A theory was developed for the influence of convection on the microstructure of lamellar and fibrous eutectics, through the effect of convection on the concentration field in the melt in front of the growing eutectic. While the theory agrees with the experimental spin-up spin-down results, it predicts that the weak convection expected due to buoyancy will not produce a measurable change in eutectic microstructure. Thus, this theory does not explain the two fold decrease in MnBi fiber size and spacing observed when MnBi-Bi is solidified in space or on Earth with a magnetic field applied. Attention was turned to the morphology of the MnBi-Bi interface and to the generation of freezing rate fluctuations by convection. Decanting the melt during solidification of MnBi-Bi eutectic showed that the MnBi phase projects into the melt ahead of the Bi matrix. Temperature measurements in a Bi melt in the vertical Bridgman-Stockbarger configuration showed temperature variations of up to 25 C. Conclusions are drawn and discussed.

Wilcox, William R.↗
NASA NTRS1993

Computational strategies in the dynamic simulation of constrained flexible MBS

This research focuses on the computational dynamics of flexible constrained multibody systems. At first a recursive mapping formulation of the kinematical expressions in a minimum dimension as well as the matrix representation of the equations of motion are presented. The method employs Kane's equation, FEM, and concepts of continuum mechanics. The generalized active forces are extended to include the effects of high temperature conditions, such as creep, thermal stress, and elastic-plastic deformation. The time variant constraint relations for rolling/contact conditions between two flexible bodies are also studied. The constraints for validation of MBS simulation of gear meshing contact using a modified Timoshenko beam theory are also presented. The last part deals with minimization of vibration/deformation of the elastic beam in multibody systems making use of time variant boundary conditions. The above methodologies and computational procedures developed are being implemented in a program called DYAMUS.

Amirouche, F. M. L.↗
NASA NTRS2002

Efficient Reformulation of HOTFGM: Heat Conduction with Variable Thermal Conductivity

Functionally graded materials (FGMs) have become one of the major research topics in the mechanics of materials community during the past fifteen years. FGMs are heterogeneous materials, characterized by spatially variable microstructure, and thus spatially variable macroscopic properties, introduced to enhance material or structural performance. The spatially variable material properties make FGMs challenging to analyze. The review of the various techniques employed to analyze the thermodynamical response of FGMs reveals two distinct and fundamentally different computational strategies, called uncoupled macromechanical and coupled micromechanical approaches by some investigators. The uncoupled macromechanical approaches ignore the effect of microstructural gradation by employing specific spatial variations of material properties, which are either assumed or obtained by local homogenization, thereby resulting in erroneous results under certain circumstances. In contrast, the coupled approaches explicitly account for the micro-macrostructural interaction, albeit at a significantly higher computational cost. The higher-order theory for functionally graded materials (HOTFGM) developed by Aboudi et al. is representative of the coupled approach. However, despite its demonstrated utility in applications where micro-macrostructural coupling effects are important, the theory's full potential is yet to be realized because the original formulation of HOTFGM is computationally intensive. This, in turn, limits the size of problems that can be solved due to the large number of equations required to mimic realistic material microstructures. Therefore, a basis for an efficient reformulation of HOTFGM, referred to as user-friendly formulation, is developed herein, and subsequently employed in the construction of the efficient reformulation using the local/global conductivity matrix approach. In order to extend HOTFGM's range of applicability, spatially variable thermal conductivity capability at the local level is incorporated into the efficient reformulation. Analytical solutions to validate both the user-friendly and efficient reformulations am also developed. Volume discretization sensitivity and validation studies, as well as a practical application of the developed efficient reformulation are subsequently carried out. The presented results illustrate the accuracy and implementability of both the user-friendly formulation and the efficient reformulation of HOTFGM.

Zhong, Yi↗
NASA NTRS2003

Predictive models for moving contact line flows

Modeling flows with moving contact lines poses the formidable challenge that the usual assumptions of Newtonian fluid and no-slip condition give rise to a well-known singularity. This singularity prevents one from satisfying the contact angle condition to compute the shape of the fluid-fluid interface, a crucial calculation without which design parameters such as the pressure drop needed to move an immiscible 2-fluid system through a solid matrix cannot be evaluated. Some progress has been made for low Capillary number spreading flows. Combining experimental measurements of fluid-fluid interfaces very near the moving contact line with an analytical expression for the interface shape, we can determine a parameter that forms a boundary condition for the macroscopic interface shape when Ca much les than l. This parameter, which plays the role of an "apparent" or macroscopic dynamic contact angle, is shown by the theory to depend on the system geometry through the macroscopic length scale. This theoretically established dependence on geometry allows this parameter to be "transferable" from the geometry of the measurement to any other geometry involving the same material system. Unfortunately this prediction of the theory cannot be tested on Earth.

Rame, Enrique↗
DOE OSTI2024

Quasiclassical Gluon Fields and Low’s Soft Theorem at Small Momentum-Fraction x

In the high-energy limit, soft gluons can be approximately described by quasiclassical gluon fields. It is well known that the gluon field is a pure gauge field on the transverse plane at eikonal order. We derived the complete next-to-eikonal order solutions of the classical Yang-Mills equations for soft gluons in the dense nuclear regime. Utilizing these solutions, it is shown that Low’s soft theorem at small x can be obtained by considering off-diagonal matrix elements of quasiclassical chromoelectric field between single-gluon states in the dilute regime. We further propose on extending Low’s soft theorem at small x to incorporate the effects of gluon saturation in the dense regime.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2026

Resonant Landau-Zener conversion in multi-axion systems

Multiple axions may emerge in the low-energy effective theory of Nature. Generically, the potentials describing these axion fields are non-diagonal, leading to mass mixing between axion states which can be temperature-dependent due to QCD instanton effects. As the temperature of the Universe drops, level crossing can occur, causing resonant conversion between axion states. In this work, we present an analytic study of the cosmological evolution of multi-axion systems including adiabatic and non-adiabatic resonant conversion from one axion state into another during the misalignment process. We show how the Landau-Zener formalism accurately captures the non-adiabatic resonant conversion, permitting an analytic description of the relic abundances of each axion field for nearly any arbitrary two-state axion mass matrix. As an application, we study the mixing of a QCD axion with an axion-like-particle for specific potentials to identify the predictions for haloscope experiments. We conclude that the detection of an axion off the expected QCD mass-coupling line predicts other haloscope targets if it mixes with the QCD axion.

Axions and ALPs↗
DOE OSTI2020

Complex Density Wave Orders and Quantum Phase Transitions in a Model of Square-Lattice Rydberg Atom Arrays

In this work, we describe the zero-temperature phase diagram of a model of a two-dimensional square-lattice array of neutral atoms, excited into Rydberg states and interacting via strong van der Waals interactions. Using the density-matrix renormalization group algorithm, we map out the phase diagram and obtain a rich variety of phases featuring complex density wave orderings, upon varying lattice spacing and laser detuning. While some of these phases result from the classical optimization of the van der Waals energy, we also find intrinsically quantum-ordered phases stabilized by quantum fluctuations. These phases are surrounded by novel quantum phase transitions, which we analyze by finite-size scaling numerics and Landau theories. Our work highlights Rydberg quantum simulators in higher dimensions as promising platforms to realize exotic many-body phenomena.

74 ATOMIC AND MOLECULAR PHYSICS↗