Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “IRRADIATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Microscopic analysis of irradiated AGR-1 coated particle fuel compacts

The AGR-1 experiment involved irradiation of 72 TRISO-coated particle fuel compacts to a peak burnup of 19.5% FIMA with no in-pile failures observed out of 3×105 total particles. Irradiated AGR-1 fuel compacts have been cross-sectioned and analyzed with optical microscopy to characterize kernel, buffer, and coating behavior. Five compacts have been examined so far, spanning a range of irradiation conditions (burnup, fast fluence, and irradiation temperature) and including all four TRISO coating variations irradiated in the AGR-1 experiment. The cylindrical specimens were sectioned both transversely and longitudinally, then polished to expose between approximately 40-80 individual particles on each mount. The analysis focused primarily on kernel swelling and porosity, buffer densification and fracturing, buffer-IPyC debonding, and fractures in the IPyC and SiC layers. Characteristic morphologies have been identified, over 800 particles have been classified, and spatial distributions of particle types have been mapped. No significant spatial patterns were discovered in these cross sections. However, some trends were found between morphological types and certain behavioral aspects. Buffer fractures were found in approximately 23% of the particles, and these fractures often resulted in unconstrained kernel swelling into the open cavities. Fractured buffers and buffers that stayed bonded to IPyC layers appear related to larger pore size in kernels. Buffer-IPyC interface integrity evidently factored into initiation of rare IPyC fractures. Fractures through part of the SiC layer were found in only three particles, all in conjunction with IPyC-SiC debonding. Compiled results suggest that the deliberate coating fabrication variations influenced the frequencies of IPyC fractures, IPyC-SiC debonds, and SiC fractures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Response of 9Cr-ODS Steel to Proton Irradiation at 400 °C

The stability of Y–Ti–O nanoclusters, dislocation structure, and grain boundary segregation in 9Cr-ODS steels has been investigated following proton irradiation at 400 °C with damage levels up to 3.7 dpa. A slight coarsening and a decrease in number density of nanoclusters were observed as a result of irradiation. The composition of nanoclusters was also observed to change with a slight increase of Y and Cr concentration in the nanoclusters following irradiation. Size, density, and composition of the nanoclusters were investigated as a function of nanocluster size, specifically classified to three groups. In addition to the changes in nanoclusters, dislocation loops were observed after irradiation. Finally, radiation-induced enrichment of Cr and depletion of W were observed at grain boundaries after irradiation.

99 GENERAL AND MISCELLANEOUS↗

Ultrasonic Transducer Irradiation Test Results

Ultrasonic technologies offer the potential for high-accuracy and -resolution in-pile measurement of a range of parameters, including geometry changes, temperature, crack initiation and growth, gas pressure and composition, and microstructural changes. Many Department of Energy-Office of Nuclear Energy (DOE-NE) programs are exploring the use of ultrasonic technologies to provide enhanced sensors for in-pile instrumentation during irradiation testing. For example, the ability of small diameter ultrasonic thermometers (UTs) to provide a temperature profile in candidate metallic and oxide fuel would provide much needed data for validating new fuel performance models. Other ongoing efforts include an ultrasonic technique to detect morphology changes (such as crack initiation and growth) and acoustic techniques to evaluate fission gas composition and pressure. These efforts are limited by the lack of identified ultrasonic transducer materials capable of long term performance under irradiation test conditions. For this reason, the Pennsylvania State University (PSU) was awarded an ATR NSUF project to evaluate the performance of promising magnetostrictive and piezoelectric transducers in the Massachusetts Institute of Technology Research Reactor (MITR) up to a fast fluence of at least 10 21 n/cm 2 . The goal of this research is to characterize and demonstrate magnetostrictive and piezoelectric transducer operation during irradiation, enabling the development of novel radiation-tolerant ultrasonic sensors for use in Material Testing Reactors (MTRs). As such, this test is an instrumented lead test and real-time transducer performance data is collected along with temperature and neutron and gamma flux data. The current work bridges the gap between proven out-of-pile ultrasonic techniques and in-pile deployment of ultrasonic sensors by acquiring the data necessary to demonstrate the performance of ultrasonic transducers. To date, one piezoelectric transducer and two magnetostrictive transducers have demonstrated reliable operation under irradiation. The irradiation is ongoing.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Validation of the Physics Analysis used to Characterize the AGR-1 TRISO Fuel Irradiation Test

The results of a detailed physics depletion calculation used to characterize the AGR-1 TRISO-coated particle fuel test irradiated in the Advanced Test Reactor (ATR) at the Idaho National Laboratory are compared to measured data for the purpose of validation. The particle fuel was irradiated for 13 ATR power cycles over three calendar years. The physics analysis predicts compact burnups ranging from 11.30-19.56% FIMA and cumulative neutron fast fluence from 2.21?4.39E+25 n/m 2 under simulated high-temperature gas-cooled reactor conditions in the ATR. The physics depletion calculation can provide a full characterization of all 72 irradiated TRISO-coated particle compacts during and post-irradiation, so validation of this physics calculation was a top priority. The validation of the physics analysis was done through comparisons with available measured experimental data which included: 1) high-resolution gamma scans for compact activity and burnup, 2) mass spectrometry for compact burnup, 3) flux wires for cumulative fast fluence, and 4) mass spectrometry for individual actinide and fission product concentrations. The measured data are generally in very good agreement with the calculated results, and therefore provide an adequate validation of the physics analysis and the results used to characterize the irradiated AGR-1 TRISO fuel.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Measurement of Diameter Changes during Irradiation Testing

New materials are being considered for fuel, cladding, and structures in advanced and existing nuclear reactors. Such materials can experience significant dimensional and physical changes during irradiation. Currently in the US, such changes are measured by repeatedly irradiating a specimen for a specified period of time and then removing it from the reactor for evaluation. The time and labor to remove, examine, and return irradiated samples for each measurement makes this approach very expensive. In addition, such techniques provide limited data and handling may disturb the phenomena of interest. In-pile detection of changes in geometry is sorely needed to understand real-time behavior during irradiation testing of fuels and materials in high flux US Material and Test Reactors (MTRs). This paper presents development results of an advanced Linear Variable Differential Transformer-based test rig capable of detecting real-time changes in diameter of fuel rods or material samples during irradiation in US MTRs. This test rig is being developed at the Idaho National Laboratory and will provide experimenters with a unique capability to measure diameter changes associated with fuel and cladding swelling, pellet-clad interaction, and crud buildup.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

In-Situ Proton Irradiation-Corrosion Study of ATF Candidate Alloys in Simulated PWR Primary Water

Irradiation enhanced corrosion behavior of Accident Tolerant Fuel candidate alloys T91 and Fe15Cr4Al were evaluated using in-situ proton irradiation-corrosion experiments in hydrogenated pure water (at 320 °C, 3 wppm H2) with a 5.4 MeV proton beam. The thin sample acted as a “window” to allow protons to fully penetrate the sample while maintaining system pressure. The area of the samples exposed to the proton beam experienced effects from displacement damage and radiolysis products. The aim of the study was to characterize the effect of radiation on the kinetics and character of oxidation caused by accelerated waterside corrosion under irradiation. Samples irradiated with protons for total displacement damage of *0.1 dpa (dose rate in water, 400 kGy/s) at an exposure time of 24 h were compared. Oxide morphology, phase structure, and composition of the oxide, metal and the metal/oxide interface were investigated using TEM and EDS and are related to the test conditions. The oxidation rate or resulting oxide thickness is dependent on the alloy Cr content; the oxidation rate increased as the Cr content decreased. The resulting oxide consists of an inner layer of Cr-rich spinel oxide and outer magnetite crystals in the unirradiated region; while the irradiated region consists of Cr-rich inner oxide spinel that was partially dissolved and coverage of outer non-faceted hematite precipitates.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Advanced Characterization of Irradiated Fuels and Materials at INL

Advanced characterization of the irradiated fuels and materials is crucial to help understanding the material and fuel property changes under irradiation. Microstructural defect evolution down to nanometer scale could strongly affect the material and fuel performance on macroscale. Radiation-induced material degradation include dimensional instability, hardening and embrittlement, intergranular cracking, radiation-enhanced chemical interaction at the interfaces and breakaway swelling. To mitigate the radiation damage, advanced characterization on irradiated microstructure, microchemistry, micromechanical property and local thermal property is necessary to identify the controlling mechanisms that are responsible to the degradations. This presentation provides a summary of the advanced characterization capabilities at the Irradiation Materials Characterization Laboratory (IMCL), Materials and Fuels Complex (MFC), Idaho National Laboratory (INL). It highlights the recently established capabilities including shield sample preparation area (SSPA), shield confinement cells for two focused ion beam (FIB) systems, a shielded electron probe microanalysis (EPMA), the thermal property microscopy (TPM) along with non-shielded instruments like scanning electron microscopy (SEM), X-ray diffractometer, and transmission electron microscopy (TEM). Some examples on advanced characterizations on irradiated structural materials and fuels will be presented. It demonstrates the power of combining sample preparation of highly radioactive materials with the advanced characterization down to atomic resolutions within one facility.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effect of Water Chemistry on Crack Growth Rate in Neutron Irradiated X-750 and XM-19

The Advanced Test Reactor (ATR) National Science User Facility (NSUF) was used to study the effect of neutron damage on crack growth rates (CGR) under simulated boiling water reactor (BWR) water chemistry conditions using a fast neutron spectrum to accelerate the damage process. Nickel based Alloy X-750 and XM-19 were irradiated in the ATR center flux trap (CFT), with this experiment marking the first civilian project to utilize this position within the reactor. 0.4T-CT specimens were used to study crack growth rates for two sample fluences (~1.9 x 1020 n/cm2 and ~9.5 x 1020 n/cm2, E > 1MeV)) in both normal water chemistry (NWC) at 2.5 ppm O2 and hydrogen water chemistry (HWC) at ~80 ppb H2. CGR testing was conducted at a temperature of 288 °C. A decrease in CGR was observed for both alloys with the average ratio (CGR in NWC/CGR in HWC) being a factor of 281 for the XM-19 samples and a factor of 27.8 for the X-750 samples. Observed CGRs in this study showed little difference compared to non-irradiated samples (the non-irradiated XM-19 was 20% cold worked), suggesting limited sensitivity of these susceptible alloys to irradiation effects. Detailed results of CGR response to varying environmental electrochemical potential (ECP) and water purity will be presented in the context of crack growth mitigation in different water chemistries and the change in material behavior relative to non-irradiated samples of the material.

36 MATERIALS SCIENCE↗

Micromechanical tests of ion irradiated materials: Atomistic simulations and experiments

We investigated irradiation effects on Fe-Cr binary alloys by using a nano-indentation combined with a continuous stiffness measurement (CSM) technique. We modeled the nano-indentation test by using a finite element method. We could extract the intrinsic hardness and the yield stress of an irradiation hardened region by using a so-called inverse method. SiC micro-pillars of various sizes were fabricated by mask and inductively coupled plasma etching technique and compressed by using flat punch nano-indentation. Compressive fracture strength showed a clear specimen size effect. Brittle-to-Ductile transition at room temperature was observed as the specimen size decreases. The effect of irradiation on the fracture strength of SiC micro-pillars was evaluated by performing ion irradiation with Si ions. We have performed molecular dynamics simulations of nano-indentation and nano-pillar compression tests. Radiation effect was observed which is found to be due to the interaction of dislocations nucleated by spherical indenter with pre-existing radiation defects (voids). These atomistic simulations are expected to significantly contribute to the investigation of the fundamental deformation mechanism of small scale irradiated materials. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

NUHOWS - Storage and Transportation of Irradiated Reactor Components in Large Packages - 13439

Most irradiated reactor components (hardware such as Control Rod Blades, Fuel Channels, Poison Curtains, etc.) generated at reactors previously required significant processing for size reduction due to the available transportation casks not being physically capable of containing unprocessed material. As of July 1, 2008, disposal for this typical waste class (B and C) became inaccessible (for the major part of the nation) due to the Barnwell, SC disposal facility being closed to all but its three compact states (CT, NJ and SC). Currently in the United States, most facilities are storing their irradiated hardware on-site in the spent fuel pools. Until recently with the opening of the Waste Control Specialists' Texas disposal facility, utilities faced the challenges of spent fuel pool space and capacity management. However, even with WCS's disposal availability, the site currently has annual Curie limitations for disposal, which will continue to promote interim on-site storage until such time as disposal is available. In response, Transnuclear Inc., (TN) an AREVA company, proceeded with designing a new large Radioactive Waste Container (RWC) that can be used to package irradiated hardware without the need for significant processing. The design features of the RWC allows for intermittent loadings of the hardware for better packaging efficiency, higher packaging density, space savings and reduced cost. This RWC is also compatible with TN's on-site modular vault storage system. Once completely loaded, the RWC can be transported to an on-site storage facility, an off-site storage facility and/or an available disposal facility. To accommodate the transportation, TN has designed a large transportation cask, the MP197HB. As the original design was for transporting fuel, it contains the necessary shielding to allow for the transport of unprocessed irradiated reactor components, while significantly reducing the amount of irradiated hardware shipments required with the use of the new RWC. This paper provides information on the unique design features of the RWC, storage module vaults, MP197HB Transportation Cask and cost saving benefits of using the large RWC for packaging, storage, transport and disposal. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Status of the Norwegian thorium light water reactor (LWR) fuel development and irradiation test program

Thorium based fuels offer several benefits compared to uranium based fuels and should thus be an attractive alternative to conventional fuel types. In order for thorium based fuel to be licensed for use in current LWRs, material properties must be well known for fresh as well as irradiated fuel, and accurate prediction of fuel behavior must be possible to make for both normal operation and transient scenarios. Important parameters are known for fresh material but the behaviour of the fuel under irradiation is unknown particularly for low Th content. The irradiation campaign aims to widen the experience base to irradiated (Th,Pu)O{sub 2} fuel and (Th,U)O{sub 2} with low Th content and to confirm existing data for fresh fuel. The assumptions with respect to improved in-core fuel performance are confirmed by our preliminary irradiation test results, and our fuel manufacture trials so far indicate that both (Th,U)O{sub 2} and (Th,Pu)O{sub 2} fuels can be fabricated with existing technologies, which are possible to upscale to commercial volumes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Irradiation of electronic components and circuits at the Portuguese Research Reactor: Lessons learned

The behavior of electronic components and circuits under radiation is a concern shared by the nuclear industry, the space community and the high-energy physics community. Standard commercial components are used as much as possible instead of radiation hard components, since they are easier to obtain and allow a significant reduction of costs. However, these standard components need to be tested in order to determine their radiation tolerance. The Portuguese Research Reactor (RPI) is a 1 MW pool-type reactor, operating since 1961. The irradiation of electronic components and circuits is one area where a 1 MW reactor can be competitive, since the fast neutron fluences required for testing are in most cases well below 10{sup 16} n/cm{sup 2}. A program was started in 1999 to test electronics components and circuits for the LHC facility at CERN, initially using a dedicated in-pool irradiation device and later a beam line with tailored neutron and gamma filters. Neutron filters are essential to reduce the intensity of the thermal neutron flux, which does not produce significant defects in electronic components but produces unwanted radiation from activation of contacts and packages of integrated circuits and also of the printed circuit boards. In irradiations performed within the line-of-sight of the core of a fission reactor there is simultaneous gamma radiation which complicates testing in some cases. Filters can be used to reduce its importance and separate testing with a pure gamma radiation source can contribute to clarify some irradiation results. Practice has shown the need to introduce several improvements to the procedures and facilities over the years. We will review improvements done in the following areas: - Optimization of neutron and gamma filters; - Dosimetry procedures in mixed neutron / gamma fields; - Determination of hardness parameter and 1 MeV-equivalent neutron fluence; - Temperature measurement and control during irradiation; - Follow-up of reactor power operational fluctuations; - Study of gamma radiation effects only. The fission neutron spectrum can be limitative for some of the tests, as most neutrons are in the 1-2 MeV energy range. Significant progress has been made lately in compact neutron generators using D-D and D-T fusion reactions, achieving higher neutron fluxes and longer lifetime than previously available. The advantages of using compact neutron generators for testing of electronic components and circuits will be also discussed. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Updated Results of Ultrasonic Transducer Irradiation Test

Ultrasonic technologies offer the potential for high accuracy and resolution in-pile measurement of a range of parameters, including geometry changes, temperature, crack initiation and growth, gas pressure and composition, and microstructural changes. Many Department of Energy-Office of Nuclear Energy (DOE-NE) programs are exploring the use of ultrasonic technologies to provide enhanced sensors for in-pile instrumentation during irradiation testing. For example, the ability of small diameter ultrasonic thermometers (UTs) to provide a temperature profile in candidate metallic and oxide fuel would provide much needed data for validating new fuel performance models. These efforts are limited by the lack of identified ultrasonic transducer materials capable of long term performance under irradiation test conditions. To address this need, the Pennsylvania State University (PSU) was awarded an Advanced Test Reactor National Scientific User Facility (ATR NSUF) project to evaluate the performance of promising magnetostrictive and piezoelectric transducers in the Massachusetts Institute of Technology Research Reactor (MITR) up to a fast fluence of at least 10{sup 21} n/cm{sup 2}. A multi-National Laboratory collaboration funded by the Nuclear Energy Enabling Technologies Advanced Sensors and Instrumentation (NEET-ASI) program also provided initial support for this effort. This irradiation, which started in February 2014, is an instrumented lead test and real-time transducer performance data are collected along with temperature and neutron and gamma flux data. The irradiation is ongoing and will continue to approximately mid-2015. To date, very encouraging results have been attained as several transducers continue to operate under irradiation. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Progress in developing laser based post irradiation examination infrastructure

To be able to understand the performance of reactor fuels and materials, irradiated materials must be characterized effectively and efficiently in high rad environments. This characterization work is performed remotely and in environments generally hostile to instrumentation. Laser based characterization techniques provide the ability to operate remotely and robustly in a hot-cell environment. Laser based instrumentation also can provide high spatial resolution suitable for scanning and imaging large areas. The INL is currently developing three laser based Post Irradiation Examination (PIE) stations for the Hot Fuel Examination Facility (HFEF) at the INL. These laser based systems will characterize irradiated materials and fuels. The characterization systems are the following: -) laser shock, -) laser based ultrasonic C-scan system and -) gas assay, sample and recharge system (GASR, up-grade to an existing system). The laser shock technique will characterize material properties and failure loads/mechanisms in various materials such as Light Water Reactor (LWR) fuel, plate fuel, and next generation fuel forms in high radiation areas. The laser shock-technique induces large amplitude shock waves to mechanically characterize interfaces such as the fuel-clad bond. As part of the laser shock system, a laser-based ultrasonic C-scan system will be used to detect and characterize de bonding caused by the application of the laser shock as well as performing classical non-destructive evaluation testing and imaging functions such as microstructure characterization, flaw detection and dimensional metrology. A spectroscopy capability can be added later as the salient components to perform Light Induced Breakdown Spectroscopy will be in place. Additional fiber ports in the feed-through will also enable future spectroscopic techniques to be efficiently installed and operated. The purpose of the GASR is to measure the pressure/volume of the plenum of an irradiated fuel element/capsule and obtain fission gas samples for analysis. The study of pressure and volume in the plenum of an irradiated fuel element/capsule and the analysis of fission gases released is important to understanding the performance of reactor fuels and materials. The main function of the laser in this application is to puncture the fuel rod or plate to allow the fission gas to escape and if necessary to weld the hole close. This system may also be used to measure the pressure/volume of other components (such as control blades) and obtain gas samples from these components for analysis. The GASR upgrade will match the functionality of the current system and provide these important functions on fuels made from current and future engineered materials. The GASR station will also have the inherent capability to perform cutting welding and joining functions within a hot-cell. The extra fiber ports built into the hot cell feed-through will also enable the efficient installation of future laser processing work benches. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Comparison of Advanced Processing of Irradiated UO{sub 2} Fuels and NpO{sub 2} Targets

Advanced processing methods for UO{sub 2}-based used nuclear fuels have been developed and demonstrated in several experimental programs at the Oak Ridge National Laboratory's Radiochemical Engineering Development Center (REDC). The Consolidated Fuel Recycle Program (1979-1986) and the Advanced Fuel Cycle Initiative (2002- 2008) were sponsored by the U.S. Department of Energy Office of Nuclear Energy (DOE/NE). Currently, DOE/NE is administering a new program for the National Aeronautics and Space Administration to produce {sup 238}Pu by irradiating NpO{sub 2}, and the irradiated targets are to be chemically processed using the same equipment and shielded facilities in the REDC that were used previously to process irradiated UO{sub 2}-based fuels. Flowsheets for processing irradiated NpO{sub 2} targets are now being developed and demonstrated. There are both similarities and differences in the processing of the two types of irradiated fuels/targets, and a comparison of these is useful for application to new types of feed material. A comparison of similarities and differences for processing UO{sub 2}- and NpO{sub 2}-based feed materials has been useful in planning for advanced processing methods and new requirements. Use of existing multistage solvent extraction equipment and shielded processing facilities at the ORNL REDC has enabled development, demonstration, and application of new and improved separations methods. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Characterization of Ion Implantation and Irradiation Effects in Interface-Dominated Metallic Composites

The candidate structural and fuel cladding materials for the next-generation nuclear power reactors must possess excellent irradiation damage tolerance, and high mechanical and thermal stability that present a challenge for materials design. Here we report an approach to engineer interphase boundaries in metallic composites to achieve superior resistance to void swelling and prevent loss of plastic deformability after irradiation. Model composite systems of face-centered-cubic (Cu) and body-centered-cubic (Nb, Mo or V) metals are used to elucidate the effects of boundary structure and spacing on the damage accumulation and mechanical properties after irradiation. Transmission electron microscopy (TEM) and nano-mechanical testing are used to characterize the irradiation response. A recent development in in situ straining in high-resolution TEM to measure lattice strains and thereby estimate local stresses corresponding to dislocation nucleation and migration is discussed as a capability that in future can enable quantitative characterization of defect interactions in irradiated materials. (authors)

36 MATERIALS SCIENCE↗

Synchrotron Microdiffraction Study of Heavy-Ion-Irradiated Uranium-Molybdenum Dispersion Fuel

There has been an ongoing effort by the Department of Energy Office of Material Management and Minimization to convert research and test reactors from high-enriched to low-enriched uranium fuels. Uranium-molybdenum alloy fuel dispersed in an aluminum matrix (UMo-Al dispersion fuel) has emerged as the leading candidate fuel for converting the remaining high-power research reactors in Europe. One of the primary barriers to using this fuel type is the deleterious reaction of UMo with Al. Depending on the operating temperature of the reactor, this interaction layer can be amorphous under irradiation and allows for the accumulation of fission gas products in large bubbles, leading to unacceptable swelling of the fuel. Therefore, detailed characterization of the phases that form within the fuel and in the interaction layer is critical to understanding, and controlling, UMo-Al dispersion fuel behavior under irradiation. Furthermore, the phase stability of the UMo fuel is of great importance, as the alpha-UMo phase has undesirable swelling compared to the metastable gamma-UMo phase. Heavy ion irradiation was used to reproduce the interaction layer that develops in-reactor. Samples of both the fuel and interaction layer formed under ion irradiation were examined using the high-energy x-ray microdiffraction technique at the Advanced Photon Source (APS) at Argonne National Laboratory to examine the microstructure of the interaction layer. The high-resolution phase information obtained in this experiment provides a valuable basis for understanding the evolution of UMo-Al dispersion fuel under irradiation and as input for computational studies to improve predictive capabilities. Phase information for in-pile fuels can currently be determined from TEM samples (limited sample volume, limiting statistics), or by extrapolation from SEMEDS analysis. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Positron Annihilation Spectroscopy Investigation of Vacancy Clusters in Neutron-Irradiated 3C-SiC

Silicon carbide (SiC) has been widely applied or considered in nuclear systems as fuel and structural materials since 1960's, given its high-temperature stability, chemical inertness, and exceptional irradiation resistance. Chemically vapor deposited (CVD) SiC has been considered as the pressure vessel materials for the TRISO fuel particles used in high temperature gas-cooled reactors or novel accident tolerant fuel concepts for light water reactors. The use of SiC/SiC composites as primary structural materials has also been proposed in fusion reactors. Driven by the need to enlarge the safety margins of nuclear reactors in accident scenarios, R and D of accident-tolerant fuel has become an important topic in the nuclear engineering and materials community. A continuous fiber SiC/SiC composite is under consideration for Zr alloy cladding replacement. Microstructural development and mechanical property change in SiC subject to neutron and ion irradiation have been studied extensively and understood well. However, the information of small vacancy cluster (i.e., those invisible in TEM) evolution in SiC exposed to neutron irradiation is still lacking, and such small clusters is suspected to play an important role in swelling, radiation creep, and thermal conductivity degradation. In this study, positron annihilation spectroscopy is used to characterize the vacancy defects in 3C-SiC exposed to various neutron irradiation conditions to capture the dependence of temperature and irradiation dose. The obtained vacancy cluster distribution is then linked to the measured swelling behavior to provide insight into the relationship between microstructure and physical property of SiC. (authors)

36 MATERIALS SCIENCE↗