Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HANDBOOK”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Evaluation of Allowed Outage Times Through Risk Priority Numbers

This paper develops and applies a new methodology for determining the Allowed Outage Times (AOTs, also referred to as Completion Times) for Limiting Conditions of Operation (LCOs) in Technical Safety Requirements (TSR) documents. AOT is defined in NUREG/CR-6141, Handbook of Methods for Risk-Based Analyses of Technical Specifications, as “the time for which a component or a train in a safety system can remain inoperable before an action is required.” Due to the risk increase incurred by loss of a safety structure, system, or component (SSC) or specific administrative control (SAC), the AOT provides “adequate time to repair a failed component without incurring undue risk.”

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Aerosol Vertical Profiling at Oliktok Point (AVPOP) Field Campaign Report

Aerosols are an important component of the atmospheric system through their various impacts on climate. Notably, the largest uncertainty of the energy budget (i.e., radiative forcing estimate) is the aerosol indirect effect. Aerosol-induced microphysical modifications influence cloud lifetime and albedo. However, constraining aerosol-cloud impacts in climate models, specifically in regions such as the Arctic, remains a significant challenge due to limited observations. The efficacy of an aerosol to impact the arctic energy budget largely depends on its concentration, composition, and source. While ground-based measurements will provide a consistent, high-resolution time series of aerosol observations, the arctic atmosphere can be stratified, and thus what is observed on the ground may not be representative of the aerosol aloft. A key gap in arctic aerosol research is routine vertical profiling of abundance and source characterization. Previous work outside of the Arctic has focused on using launched or tethered balloon systems (LBS and TBS, respectively) to measure vertical profiles of aerosol size distributions and has demonstrated the utility of such observations (e.g., Hofmann et al. 1989; Hofmann 1993; Iwasaka et al. 2003; Kim et al. 2003; Tobo et al. 2007). More specifically, particle spectrometers have also been deployed via TBS systems (de Boer et al. 2018; Greenberg et al. 2009; Maletto et al. 2003; Renard et al. 2016; Wehner et al. 2007; Siebert et al. 2004) affording information on aerosol layer locations and evolution by means of multiple profiles. Filter samples for post-processing of aerosol composition and ice nucleation properties have also been conducted in mid-latitudes (Creamean et al. 2018). However, while these studies present novel measurements of aerosol vertical profiling via balloon systems, few exist to date in the Arctic. The U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) user facility TBS is composed of a variety of winches, balloons, and instrumentation that flies within ARM’s Restricted Airspace (R-2204) at the third ARM Mobile Facility (AMF3) at Oliktok Point, Alaska (Figure 1). The system payload comprises instruments that can simultaneously collect in situ data on horizontal winds, ice microphysics, turbulence, thermodynamic state, aerosols, and the cloud-top environment (https://www.arm.gov/capabilities/instruments/tbs). Recent campaigns at AMF3 have involved the use of the ARM helikite, which is a balloon-kite hybrid that uses lighter-than-air principles to obtain its initial lift and a kite to achieve stability and dynamic lift. Additional information on the specifications of the helikite TBS can be found in the ARM TBS handbook (Dexheimer 2018).

Oliktok Point, North Slope of Alaska,, tethered ba↗

Initial Application of TSUNAMI for Validation of Advanced Fuel Systems

A number of advanced reactor concepts and accident-tolerant fuels (ATFs) are under development or in the initial stages of deployment and testing in the nuclear power industry. Many of these concepts incorporate chemical or material forms that have not traditionally been used in the nuclear industry and may present challenges for nuclear criticality safety validation. Sensitivity/uncertainty methods are ideally suited for assessing the applicability of existing critical experiments to these potentially challenging applications. This paper presents two case studies recently completed at Oak Ridge National Laboratory (ORNL) which investigated the use of the TSUNAMI tools within the SCALE code system to perform such assessments.Many advanced reactor concepts include uranium enrichments above 5 wt% 235U but below the 20 wt% limit of low-enriched uranium (LEU). This material, referred to as high assay LEU (HA-LEU), poses difficulties across the entire infrastructure of nuclear power, including enrichment, transportation, fabrication, and storage. A potentially representative transportation package was selected to perform a criticality safety validation assessment for UF6 containing HA-LEU. Sensitivity data were generated using the TSUNAMI-3D sequence, and an assessment of the applicability of a range of critical experiments was performed using the TSUNAMI-IP tool. The critical experiments were drawn from the set of available sensitivity data files distributed with the International Criticality Safety Benchmark Evaluation Project (ICSBEP) Handbook. The results indicate that a sufficient number of available experiments may be available to perform validations for these systems.Many different cladding materials and fuel dopants are included in ATFs to mitigate the consequences of a loss of coolant accident. Some of these systems have already been fabricated and introduced as lead test assemblies in commercial reactors, while others are still being developed. Several concepts were considered for pressurized-water reactors (PWRs) and boiling-water reactors (BWRs) in comparison to the current Zircaloy and UO2 fuel system. In most of these cases, the ATF materials did not significantly impact the number of applicable experiments for validation. Some fuel and cladding materials were identified, however, which may reduce the number of available experiments and which will increase the nuclear data–induced uncertainty in neutron multiplication.

Marshall, William (B.J.)↗

Consensus International Solar Resource Standards and Best Practices Development: Preprint

Standardization and best practices of data sets and models enable the industry to develop widely accepted protocols for various stages of solar project development and operations. In collaboration with the International Energy Agency Photovoltaic Power Systems Programme Task 16, the National Renewable Energy Laboratory (NREL) developed and regularly updates the Best Practices Handbook for the Collection and Use of Solar Resource Data for Solar Energy Applications. In collaboration with ASTM members on the radiometry subcommittee, NREL assists in and leads the development of radiometric standards that contribute to increased accuracy in the measurement of solar resources available to conversion systems and to the development and improvement of models. These models can then provide long-term geographic distribution of solar resources for areas where measured solar data are not available. Further, these standards play a preeminent role in all aspects of solar energy projects, including standard conditions, methods and instrumentation, accelerated testing, and service lifetime of materials.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Exceptional fatigue resistance and impact toughness of additively manufactured nickel alloy 625 by laser powder bed fusion

A thorough understanding of the processing-structure property relationships of additively manufactured (AM) parts is critical for applications. Detailed microstructural, tensile, axial fatigue, and Charpy impact properties were evaluated of AM nickel alloy 625 builds produced by laser-beam powder-bed-fusion, with powders manufactured using different atomization conditions. Post-heat treatment resulted in a recrystallized, equiaxed grain structure that eliminated anisotropy in tensile properties between the build and transverse directions. Axial fatigue properties along the build direction were similar to design handbook wrought fatigue data. Furthermore, Charpy impact energy values were superior to wrought data in the hot-rolled condition. Fractography was performed on failed fatigue and Charpy specimens and the fracture surfaces of Charpy specimens were found to be covered predominantly by fine dimples.

36 MATERIALS SCIENCE↗

Statistical Sampling Plan for AGR-5/6/7 Fuel Materials

Kernels, coated particles, and compacts will be manufactured to predefined specifications for irradiation in the AGR 5/6/7 experiments. Many tests will be performed for quality assurance and most of these tests correspond to criteria that have to be met with 95% confidence, based on random samples. This report describes the statistical acceptance testing methods and gives minimum sample sizes for kernels to achieve 95% confidence. Coated particles and compacts will be addressed in revisions to this report. The methods used for sample size determination are described in detail in INL/EXT 05 00349, Statistical Methods Handbook for Advanced Gas Reactor Fuel Materials (Einerson 2005). The statistical approach is to collect a representative sample, apply an acceptance test to the sample, and accept or reject the product based on this test for each criterion. The criteria or “product specifications” are contained in SPC-1352, “AGR 5/6/7 Fuel Specification,” Revision 1 and are duplicated in this plan.

ECAR-1930 BASELINE CHARACTERIZATION DATABASE VERIFICATION REPORT - NBG-18 BILLET 635-14

The purpose of this Engineering Calculations and Analysis Report is to present the data being collected in the Baseline Graphite Characterization program, which is directly tasked with supporting the Idaho National Laboratory’s (INL’s) research and development efforts on the Next Generation Nuclear Plant (NGNP)/Very High Temperature Reactor (VHTR). This program is populating a comprehensive database that will reflect the baseline properties of nuclear-grade graphite with regard to individual grade, billet, and position within individual billets. The physical and mechanical property information being collected will be transferred to the NGNP Data Management and Analysis System (NDMAS), and from that database will help populate handbook of property data available to member nations of the Generation IV International Forum (GIF). The transfer of this data from the applicable technical lead to the dissemination databases available to other end users requires a full review of the test procedures and data collection efforts through an analysis of the multiple summary spreadsheets and values being collected. This report represents that analysis for a single billet of nuclear grade graphite (NBG-18 billet 635-14) and facilitates the release of the associated data to the NDMAS custodians.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

A Comparison of Homogeneous and Heterogeneous Uranium Metal-Water Systems using Calculated and Experimental Critical Data

Heterogeneous effects of fissile units latticed in water has been documented in several forms in commonly referenced handbooks and guides. Many of these documents provide guidance for when heterogeneous systems are more reactive than their homogenous counterparts if controlling fissile mass or volume. This information provides insight into when heterogeneity should be considered for conservatism, however this information is not always displayed in a manner that is comparable to commonly referenced data, such as critical curves based on spherical systems. This paper aims to provide a juxtaposition of homogenous and heterogeneous uranium metal-water systems using both experimental and calculated critical data displayed in the format of commonly referenced critical curves. This format allows for easy comparison between the two systems against parameters that are often considered for single unit analysis such as: uranium density, fissile mass, system volume, and total system mass (fissile mass plus moderator mass). Calculated critical spherical systems provide an equal comparison between latticed geometry types as the latticed array can be cut off or restricted in the same manner in each series of models, which is not true for experimental values. Additionally, enrichment of the latticed units can be made uniform in the calculated systems, which is also difficult to achieve when referencing experimental data of varying latticed geometries. A comparison of calculated critical values and available experimental values is provided to show how these parameters can impact the critical spherical system result.

36 MATERIALS SCIENCE↗

Verification of MCNP Critical Benchmark Model of U233-COMP-THERM-004

Los Alamos National Laboratory (LANL) has been working on creating a new centralized repository for MCNP models of critical benchmark experiments. The initial model of U233-COMP-THERM-004 was derived from the Whisper Suite provided with MCNP6.2, and was compared against the ICSBEP handbook chapter for the benchmark. Many notable errors were found in the initial model and were revised accordingly. Comparing the computational model of the old and new models confirmed that any Whisper results that relied upon the old model are still valid.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

A Comparison of Homogeneous and Heterogeneous Uranium Metal-Water Systems using Calculated and Experimental Critical Data

Heterogeneous effects of fissile units latticed in water has been documented in several forms in commonly referenced handbooks and guides. Many of these documents provide guidance for when heterogeneous systems are more reactive than their homogenous counterparts if controlling fissile mass or volume. This information provides insight into when heterogeneity should be considered for conservatism, however this information is not always displayed in a manner that is comparable to commonly referenced data, such as critical curves based on spherical systems. This paper aims to provide a juxtaposition of homogenous and heterogeneous uranium metal-water systems using both experimental and calculated critical data displayed in the format of commonly referenced critical curves. This format allows for easy comparison between the two systems against parameters that are often considered for single unit analysis such as: uranium density, fissile mass, system volume, and total system mass (fissile mass plus moderator mass). Calculated critical spherical systems provide an equal comparison between latticed geometry types as the latticed array can be physically cut off or restricted in the same manner in each series of models, which is not true for experimental values. Additionally, enrichment of the latticed units can be made uniform in the calculated systems, which is difficult to achieve when referencing experimental data of varying latticed geometries. A comparison of calculated critical values and available experimental values is provided to show how these parameters can impact the critical spherical system result.

36 MATERIALS SCIENCE↗

High-Fidelity Measurements for Flattop-HEU Benchmark Reevaluation

Flattop was first built in the 1950’s at Los Alamos National Laboratory. Flattop-HEU is composed of a sphere of highly enriched uranium (HEU) surrounded by a thick spherical natural uranium (NU) reflector. The reflector is composed of three parts: a stationary hemisphere and two movable quarter spheres. For fine control of the reactivity of the system, there are three control rods of natural uranium located in voids in the stationary hemisphere. The final components that make Flattop a useful critical assembly are the glory hole and mass adjustment pieces. These pieces can be loaded in various configurations into the glory hole and the core pedestal to control the known worth of the system. The glory hole and mass adjustment pieces are mostly small pieces of HEU with some mass adjustment pieces fabricated from NU. This allows for the irradiation of samples to a specified level. To better document the system, Flattop was evaluated and included in the International Criticality Safety Benchmark Evaluation Project (ICSBEP) handbook. The original benchmark evaluation of Flattop-HEU was written in 1999 based on an experiment completed in the 1960’s. This original evaluation was written to provide a single diameter that defined critical mass; however, as computational capabilities have increased, the focus for benchmark evaluations has shifted to include detailed modelswith all physical dimensions. Thus, as Flattop is a lynchpin in critical experiment work, the benchmark is being reevaluated at current standards. This summary discusses some of the largest known uncertainties from the evaluation and the high-fidelity measurements taken to reduce these uncertainties.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Updates and Validation for the n+ 63,65 Cu Cross Sections [Abstract]

The neutron induced total, elastic, and capture cross sections of 63,65 Cu isotopes were selected for evaluation in the resolved and unresolved resonance energy ranges by the National Criticality Safety Program to resolve discrepancies related to benchmark performance. This is especially evident for the series of ZEUS benchmarks in which copper is used as a reflector. Because copper is also used as structural material in both fission and fusion reactors, the need to address benchmark discrepancies linked to nuclear data deficiencies is a task of primary importance. The aim of this work is to describe the steps of evaluation work towards a consistent improvement of the benchmark performance. The R-matrix analysis with the SAMMY code focused on the 63 Cu(n,γ) reaction channel between 100-300 keV coupled to unresolved resonance region parameters up to 650 keV to fit average cross section data from a recent experiment. Due to the high sensitivity of many benchmarks to elastic scattering angular distribution data, especially for the 65 Cu isotope, the impact of these data was tested by generating Legendre coefficients from both resonance parameters and the Hauser-Feshbach model. Guided by the findings of Shaw et al., the performance of the current evaluation for 65 Cu was compared to that of ENDF/B-VII.1 and ENDF/B-VIII.0 by testing the reactivity coefficients corresponding to the validation suite of experimental criticality benchmarks for thermal, intermediate, and fast systems taken from the International Criticality Safety Benchmark Experiments Project Handbook. The benchmark performance is especially sensitive to 63 Cu(n,γ) and 65 Cu elastic scattering for neutron energies in the 100–500 keV region, whereas 100 keV is the upper limit of the resolved resonance region in the ENDF/B-VIII.0 evaluations for 63,65 Cu. The results highlight the need to handle the transition from the resolved resonance region to the high energy region carefully.

07 ISOTOPE AND RADIATION SOURCES↗

Baseline Characterization Database Verification Report - PCEA Billet 02S8-5

The purpose of this engineering calculations and analysis report (ECAR) is to present data collected in the Baseline Graphite Characterization Program, which is directly tasked with supporting the Idaho National Laboratory's (INL's) research and development efforts on the Advanced Reactor Technologies (ART) Program. This program populates a comprehensive database that reflects the baseline properties of nuclear-grade graphite regarding individual grade, billet, and position within individual billets. The physical- and mechanical-property information being collected will be transferred to the Nuclear Data Management and Analysis System (NDMAS), and that database will help populate the handbook of property data available to member nations of the Generation-IV International Forum. Transfer of these data from the applicable technical lead to the dissemination databases available to other end users requires a full review of the test procedures and data-collection efforts through an analysis of the multiple summary spreadsheets and values being collected. This report represents the analysis for PCEA Billet 02S8-5 and facilitates release of associated data to the NDMAS custodians.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Baseline Characterization Database Verification Report - PCEA Billet 01S8-9

The purpose of this engineering calculations and analysis report (ECAR) is to present data collected in the Baseline Graphite Characterization Program, which is directly tasked with supporting the Idaho National Laboratory's (INL's) research and development efforts on the Advanced Reactor Technologies (ART) Program. This program populates a comprehensive database that reflects the baseline properties of nuclear-grade graphite with regard to individual grade, billet, and position within individual billets. The physical- and mechanical-property information being collected will be transferred to the Nuclear Data Management and Analysis System (NDMAS), and that database will help populate the handbook of property data available to member nations of the Generation-IV International Forum. Transfer of these data from the applicable technical lead to the dissemination databases available to other end users requires a full review of the test procedures and data-collection efforts through an analysis of the multiple summary spreadsheets and values being collected. This report represents the analysis for PCEA Billet 01S8-9 and facilitates release of associated data to the NDMAS custodians.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Application of a Density Law via Python for Aqueous Plutonium Nitrate

A predictive density tool has been developed in Python to reduce bias and uncertainty in nuclear criticality safety calculations for plutonium nitrate systems. The Pitzer Method and an empirical method were implemented into the tool, allowing for plutonium nitrate density calculations. Additionally, the Python tool can generate atom densities for a MCNP6.2 material card using the density from the selected method and directly the densities into a prepared MCNP6 input text file. The material card and density are calculated based on customizable user inputs of plutonium content, nitric acid content, temperature, plutonium isotope weight percentages and impurity concentrations. The Python tool has been validated and verified against the International Handbook of Evaluated Criticality Safety Benchmark Experiments to predict densities within a root mean square error of 1.0% for the Pitzer method and 1.8% for the empirical method. These errors in density were shown to lead to a ±0.5% error in MCNP6.2 calculated k effective for the Pitzer method and a ±1.7% error for the Empirical method. Simultaneous work is also being done at the University of New Mexico and Los Alamos National Laboratory to create a similar tool for plutonium chloride solutions, which aims to provide the accreditation of the chlorine absorption. These capabilities will not only provide more accurate models but also lead the way towards a better understanding of solution systems and potential relaxation in the conservatism of the current aqueous plutonium processing limits.

97 MATHEMATICS AND COMPUTING↗

MUSiC: Critical Experiment with Bare Highly Enriched Uranium Shells Benchmark

The measurements of the Uranium Subcritical and Critical (MUSiC) experiment were performed from December 2020 through April 2021. The purpose of the experiment was to test a variety of multiplicity detection systems for a large range of multiplication values and to see how well they perform as the k eff of the MUSiC series of experiments approached the delayed critical window. Out of the ten configurations that were studied, two of them were super critical and were recently approved as benchmarks and they will be included in the International Criticality Safety Benchmark Evaluation Project (ICBESP) handbook. For each of the two experiments, uncertainties were evaluated six categories: (1) critical measurement, (2) mass, (3) composition, (4) positioning, (5) dimensions, and (6) temperature. The largest contribution to the overall uncertainty in each of the cases was due to the uncertainties in the dimensions of the HEU Rocky Flats shells. Simplified detailed models were created with an average bias of -130.5 pcm due to the removal various components surrounding the experiment. For MCNP6.2 models using ENDF-VIII.0 neutron cross section data, the average difference between the calculated and benchmark k effs was -54 pcm for the detailed model and -102 pcm for the simplified model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High Multiplication Neutron Noise Measurements Using the 7uPCX Assembly

The Seven Percent Critical Experiment, or 7uPCX, is a system that mimics the physics of light water nuclear reactor systems by using uranium dioxide fuel pins at an enrichment of approximately 7%. 7uPCX is often used for benchmarking and nuclear data purposes. As part of a collaboration between Lawrence Livermore National Laboratory, Los Alamos National Laboratory, Sandia National Laboratories, and the Institut de Radioprotection et de Sûreté Nucléaire, measurements were performed in support of a high-multiplication, subcritical benchmark candidate for a thermal system. The measurements were completed by making subcritical configurations using the fuel loading pattern of a well-documented configuration of the Seven Percent Critical Experiment at Sandia National Laboratories, which exists as a benchmark in the International Criticality Safety Benchmark Evaluation Project handbook. These measurements, which aimed to capture multiplications ranging from approximately 10 to 1,000, also serve as an intercomparison between both the fielded detector systems and analysis methodologies with the goal of better characterizing the detectors and their ability to capture the state of the criticality these types of systems. Los Alamos National Laboratory’s measurements for this collaboration were made with five linked helium-3 based neutron multiplicity detectors placed on the periphery of the reactor tank beyond the infinite reflector thickness of water, and four organic scintillators placed in dry-wells in-reactor near the edge of the upper fuel grid plate. This work captures the Los Alamos National Laboratory measurements, the Rossi-α and Feynman-Y results, provides an intercomparison between the results of the 3 He neutron detectors and the organic scintillators, compares to simulation where possible, and expands on future work.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Experiments to Measure the Effect of Tantalum on Critical Systems

Sandia National Laboratories (SNL) and Oak Ridge National Laboratory (ORNL) collaborated to develop a capability to test the epithermal/intermediate cross sections of materials at the SNL critical experiment facility using the Seven Percent Critical Experiment (7uPCX) fuel. As a result, a new set of critical experiments has been designed to target the epithermal cross sections of tantalum (Ta) and is scheduled to be performed at SNL in 2023. These critical experiments will be evaluated for inclusion in the 2024 edition of the International Criticality Safety Benchmark Evaluation Project (ICSBEP) Handbook. The focus of these critical experiments is to measure the effects of Ta on the critical array size. The critical array size will be determined by an approach-to-critical experiment with the number of fuel rods in the array as a free parameter. The core configurations are designed to optimize the reactivity worth of Ta and the overall percentage of Ta absorption rates in the epithermal/intermediate energy range (0.625 eV – 100 keV). The baseline core configuration includes 7uPCX fuel rods set at a triangular pitch of 1.016 cm and a central dry test region that utilizes a cadmium liner for filtering out thermal neutrons. The central test region has locations for 85 Ta rods set at a triangular pitch of 0.813 cm. The Ta reactivity worth for the case with 85 Ta rods is approximately 2.55%, with the percentage of Ta absorption rates within the intermediate energy range at nearly 90%.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗