Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Microstructural Characteristics of HIP-bonded Monolithic Nuclear Fuels with a Diffusion Barrier

Due to the limitation of maximum uranium load achievable by dispersion fuel type, the Global Threat Reduction Initiative (GTRI) is developing an advanced monolithic fuel to convert US high performance research reactors to low-enriched uranium. Hot-isostatic-press bonding was the single process down-selected to bond monolithic U-Mo fuel meat to aluminum alloy cladding. A diffusion barrier was applied to the U–Mo fuel meat by roll-bonding process to prevent extensive interaction between fuel meat and aluminum-alloy cladding. Microstructural characterization was performed on fresh fuel plates fabricated at Idaho National Laboratory. Interfaces between fuel meat, cladding, and diffusion barrier, as well as U–10Mo fuel meat and Al–6061 cladding were characterized by scanning electron microscopy. Preliminary results indicate that the interfaces contain many different phases while decomposition, second phases, and chemical banding were also observed in the fuel meat. The important attributes of the HIP-bonded monolithic fuel are • A typical Zr diffusion barrier of thickness 25 µm • Transverse cross section that exhibits relatively equiaxed grains with an average grain diameter of 10 µm • Chemical banding, in some areas more than 100 µm in length, that is very pronounced in longitudinal (i.e., rolling) direction with Mo concentration varying from 7–13 wt% • Decomposed areas containing plate-shaped low-Mo phase • A typical Zr/cladding interaction layer of thickness 1-2 µm • A visible UZr2 bearing layer of thickness 1-2 µm • Mo-rich precipitates (mainly Mo2Zr, forming a layer in some areas) followed by a Mo-depleted sub-layer between the visible UZr2-bearing layer and the U–Mo matrix • No excessive interaction between cladding and the uncoated fuel edge • Cladding-to-cladding bonding that exhibits no cracks or porosity with second phases high in Mg, Si, and O decorating the bond line. • Some of these attributes might be critical to the irradiation performance of monolithic U-10Mo nuclear fuel. There are several issues or concerns that warrant more detailed study, such as precipitation along cladding-to-cladding bond line, chemical banding, uncovered fuel-zone edge, and interaction layer between U–Mo fuel meat and zirconium. Future post-irradiation examination results will focus, among other things, on identifying in-reactor failure mechanisms and, eventually, directing further fresh fuel characterization efforts.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Pre-conceptual Development and characterization of an extruded graphite composite fuel for the TREAT Reactor

In an effort to explore fuel systems that are more robust under accident scenarios, the DOE-NE has identified the need to resume transient testing. The Transient Reactor Test (TREAT) facility has been identified as the preferred option for the resumption of transient testing of nuclear fuel in the United States. In parallel, NNSA’s Global Threat Reduction Initiative (GTRI) Convert program is exploring the needs to replace the existing highly enriched uranium (HEU) core with low enriched uranium (LEU) core. In order to construct a new LEU core, materials and fabrication processes similar to those used in the initial core fabrication must be identified, developed and characterized. In this research, graphite matrix fuel blocks were extruded and materials properties of were measured. Initially the extrusion process followed the historic route; however, the project was expanded to explore methods to increase the graphite content of the fuel blocks and explore modern resins. Materials properties relevant to fuel performance including density, heat capacity and thermal diffusivity were measured. The relationship between process defects and materials properties will be discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Semiconductor Ion Implanters

In 1953 the Raytheon CK722 transistor was priced at $7.60. Based upon this, an Intel Xeon Quad Core processor containing 820,000,000 transistors should list at $6.2 billion. Particle accelerator technology plays an important part in the remarkable story of why that Intel product can be purchased today for a few hundred dollars. Most people of the mid twentieth century would be astonished at the ubiquity of semiconductors in the products we now buy and use every day. Though relatively expensive in the nineteen fifties they now exist in a wide range of items from high-end multicore microprocessors like the Intel product to disposable items containing 'only' hundreds or thousands like RFID chips and talking greeting cards. This historical development has been fueled by continuous advancement of the several individual technologies involved in the production of semiconductor devices including Ion Implantation and the charged particle beamlines at the heart of implant machines. In the course of its 40 year development, the worldwide implanter industry has reached annual sales levels around $2B, installed thousands of dedicated machines and directly employs thousands of workers. It represents in all these measures, as much and possibly more than any other industrial application of particle accelerator technology. This presentation discusses the history of implanter development. It touches on some of the people involved and on some of the developmental changes and challenges imposed as the requirements of the semiconductor industry evolved.

43 PARTICLE ACCELERATORS↗

ParaChoice Model

Sandia National Laboratories' (SNL's) Parametric Choice Model (ParaChoice) supports the U.S. Department of Energy Vehicle Technologies Office (VTO) mission. Using early-stage research as input, ParaChoice supports the informed development of technology that will improve affordability of transportation, while encouraging innovation and reducing dependence on petroleum. Analysis with ParaChoice enables exploration of key factors that influence consumer choice, as well as projecting the effects of technology, fuel, and infrastructure development for the vehicle fleet mix. Because of the distinct differences between requirements, needs, and use patterns for light duty vehicles (LDVs) relative to heavy duty vehicles (HDVs), this project separately models the dynamics of each of these segments to accurately characterize the factors that influence technology adoption.

33 ADVANCED PROPULSION SYSTEMS↗

Single-layer transition metal sulfide catalysts

Transition Metal Sulfides (TMS), such as molybdenum disulfide (MoS.sub.2), are the petroleum industry's "workhorse" catalysts for upgrading heavy petroleum feedstocks and removing sulfur, nitrogen and other pollutants from fuels. We have developed an improved synthesis technique to produce SLTMS catalysts, such as molybdenum disulfide, with potentially greater activity and specificity than those currently available. Applications for this technology include heavy feed upgrading, in-situ catalysis, bio-fuel conversion and coal liquefaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synergistic smart fuel for in-pile nuclear reactor measurements

The thermo-acoustic fuel rod sensor developed in this research has demonstrated a novel technique for monitoring the temperature within the core of a nuclear reactor or the temperature of the surrounding heat-transfer fluid. It uses the heat from the nuclear fuel to generate sustained acoustic oscillations whose frequency will be indicative of the temperature. Converting a nuclear fuel rod into this type of thermo-acoustic sensor simply requires the insertion of a porous material (stack). This sensor has demonstrated a synergy with the elevated temperatures that exist within the nuclear reactor using materials that have only minimal susceptibility to high-energy particle fluxes. When the sensor is in operation, the sound waves radiated from the fuel rod resonator will propagate through the surrounding cooling fluid. The frequency of these oscillations is directly correlated with an effective temperature within the fuel rod resonator. This device is self-powered and is operational even in case of total loss of power of the reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Use of Lignin-Based Admixture as Water Reducer (WRA) for Tailoring the Rheological Properties of Mortars for 3D-Printing

Efforts towards decarbonizing construction materials and industrial processes related to cement and concrete can be aided via multifaceted approaches that target alternative admixtures as well as precision control of fabrication. Chemical admixtures for water reduction have played a crucial role in the development of advanced mortar and concrete mixtures. Newer biomass processing techniques developed for aviation fuel production from corn stover biomass produce a highly reactive lignin byproduct that is suitable for chemical modifications to mimic the properties of commonly used polycarboxylate ethers (PCEs) with a smaller carbon footprint. These lignin-based plasticizers developed at NREL can be used in place of petrochemical-derived superplasticizers to tailor the rheological properties of cement-based systems for applications such as additive manufacturing while reducing the carbon intensity of the concrete mix. Lignosulfonates derived from paper pulping were historically used as water reducers only to be displaced with the rise of PCEs. The present study examines the use of a NREL produced lignin-based water reducing admixture (WRA), in cement pastes and mortar mixtures for 3D-printing at small- (mm) scale. The experimental program consisted of different formulations of oxidized lignin-based WRAs added in variable dosages to cement pastes with a fixed water-to-cement ratio. The objective is to achieve an appropriate workability, extrudability and buildability of mortar mixtures to produce 3D-printed specimens. The rheological characterization was performed to compare the initial yield stress and viscosity of the different mixtures with lignin-based admixture with respect to conventional PCE superplasticizers. The rheological characterization shows that the proposed material act as an effective water-reducer in cement systems, affecting the yield stress, plastic viscosity, and structuration rate of the mixtures evaluated. On the other hand, the effect on early hydration process of the cement pastes containing lignin-based admixtures is comparable to conventional superplasticizers.

3D-printing↗

Computational Approaches for Clean Energy Materials

Currently, 80% of the global final energy consumption occurs in form of fuels and only 20% as electricity. On the other hand, renewable energy additions come almost exclusively in the form of electricity (dominantly photovoltaics and wind). Thus, a successful energy transition will require enormous growth in renewables, sufficient to convert excess electricity into fuels, as well as the development of non-electricity based solar fuel technologies. As much as photovoltaic capacities have grown over the past 20 years, it is far from clear that current technologies and materials are up to the task to grow from here by yet another factor 100 until 2050. Therefore, sustained research efforts on emerging inorganic semiconductors for solar electricity and fuels are essential for facing the double challenge of climate change and energy security. Computational materials science can make important contributions, guiding and supporting research activities through both materials search and discovery and through detailed studies that help to develop a mechanistic understanding of materials performance and bottlenecks. This presentation will highlight three recent computational projects with relevance for photovoltaics and solar fuels (1) Defect graph neural networks (dGNN) for materials discovery in solar thermochemical hydrogen (STCH) [1]. The dGNN approach facilitates broad and fast materials screening for defect properties. (2) Modeling highly off-stoichiometric systems by evaluating the free energy of defect interaction [2]. This approach allows quantitative prediction of H2 production in complex STCH oxides. (3) First-principles atomic structure prediction for interfaces [3]. This work showed how an atomically thin CdCl2 interlayer phase enables in principle ideal electron transport across the incommensurate SnO2/CdTe interface. [1] M.D. Witman, A. Goyal, T. Ogitsu, A.H. McDaniel, S. Lany, Nat. Comput. Sci. (2023). https://doi.org/10.1038/s43588-023-00495-2. [2] A. Goyal, M.D. Sanders, R.P. O'Hayre, S. Lany, PRX Energy 3, 013008 (2024). https://doi.org/10.1103/PRXEnergy.3.013008. [3] A. Sharan, M. Nardone, D. Krasikov, N. Singh, S. Lany, Appl. Phys. Rev. 9, 041411 (2022). https://doi.org/10.1063/5.0104008.

density functional theory↗

Compatibility Assessment of Fuel System Infrastructure Plastics with Bio-oil and Diesel Fuel

We report that bio-oil derived via fast pyrolysis is being developed as a renewable fuel option for petroleum distillates. The compatibility of neat bio-oil with 18 plastic types was evaluated using neat diesel fuel as the baseline. The plastic materials included polyphenylene sulfide (PPS), polyethylene terephthalate (PET), polytetrafluoroethylene (PTFE), polyvinylidene fluoride (PVDF), polyoxymethylene (POM), POM copolymer, high density polyethylene (HDPE), polybutylene terephthalate (PBT), polypropylene (PP), polyethylene terephthalate glycol (PETG), polythiourea (PTU), four nylon grades, and four thermosetting resins. Specimens of each material were immersed in the test fuels for a period of 16 weeks to achieve full saturation. Except for PP and HDPE, the plastic materials underwent higher volume expansion in bio-oil than in the baseline diesel (which was negligible in most cases). This volume increase corresponds to the higher polarity of the bio-oil. PPS, PET, and PTFE were unaffected by bio-oil exposure, but modest swelling (between 2 and 5%) occurred for the two acetals (POM and POM copolymer), Nylon-12, PBT, PETG, and the four resin grades. More moderate swelling (8–15%) was noted for Nylon-6, Nylon-6/6, and Nylon-11, and excessive swell (>40%) occurred for PTU. The nonpolar nature of PP and HDPE matches that of diesel, leading to higher solubility (swell) in this fuel type. Finally, the relatively low volume expansion following exposure indicates that many of the existing infrastructure plastics (excluding PTU) should be suitable for use with bio-oil.

09 BIOMASS FUELS↗

Panel Session 111: Nuclear Power Plant Onsite SNF storage, ISFSIs and Failed Fuel Handling Issues

This panel session provided updates on several issues seen in developing, operating independent spent fuel storage installations (ISFSIs), Damaged Fuel and aging management recent activities. Presentations proposed include: 1 - Spent Nuclear Fuel Management Activities at Holtec (Myron Kaczmarsky, Holtec International (USA)); 2 - INL Spent Fuel Management: Challenges and Path Forward for Dry Storage (Josh Jarrell, Idaho National Laboratory (USA))

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Atomistic characterization of hydration-dependent fuel cell ionomer nanostructure: validation by vibrational spectroscopy

The development of Nafion alternatives for fuel cells and electrolyzers requires a fundamental understanding of hydration-dependent ion-exchange site acid/base chemistry. We present here reactive force field (ReaxFF) molecular dynamics (MD) simulations of Nafion at varying molar water/ion-exchange-site ratios (λ), which we correlate to our experimental and density functional theory-based vibrational spectra. ReaxFF describes the formation and breaking of covalent bonds, enabling simulations of proton exchange between sulfonic acid/sulfonate groups and water/hydronium. Our MD simulations determine the λ-dependent equilibrium proportions of protonated and deprotonated sites. We find that protonated sites persist across all λ from 0 to 20, challenging the widely accepted notion that all sites are ionized above a threshold λ value (e.g., 3 or 4). Our simulations generate hundreds of realistic exchange site environments, the characterization of which are based on 6 Å radii sulfur-centered ‘inner-spheres’. These inner- and outer-sphere regions elucidate an interplay of stereoelectronic factors that influence protonation states, including the number of inner-sphere waters (Λ). Our simulations produce broad λ-dependent distributions of Λ values, representing non-uniform exchange site hydration. Moreover, we demonstrate that these distributions are specific to both protonated and deprotonated sites, with significant overlap between the two distributions for all non-zero λ. These distributions underpin the IR spectra of hydrated membranes, with each exchange site contributing an IR spectrum characteristic of its protonation state and Λ. We expect that these nanostructural characterizations of Nafion exchange sites will contribute to the development of new ionomers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Observed Changes in As-Fabricated U-10Mo Monolithic Fuel Microstructures After Irradiation in the Advanced Test Reactor

A low-enriched uranium U-10Mo monolithic nuclear fuel is being developed by the Material Management and Minimization Program, earlier known as the Reduced Enrichment for Research and Test Reactors Program, for utilization in research and test reactors around the world that currently use high-en-riched uranium fuels. As part of this program, reactor experiments are being performed in the Advanced Test Reactor. It must be demonstrated that this fuel type exhibits mechanical integrity, geometric stability, and pre-dictable behavior to high powers and high fission densities in order for it to be a viable fuel for qualification. This paper provides an overview of the microstructures observed at different regions of interest in fuel plates before and after irradiation for fuel samples that have been tested. These fuel plates were fabricated using laboratory-scale fabrication methods. Observations regarding how microstructural changes during irradiation may impact fuel performance are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Delayed fire mortality has long‐term ecological effects across the Southern Appalachian landscape

Abstract Fire is a critical ecological process to the forests of the Southern Appalachians. Where fire was excluded from forest types that historically burned frequently, unanticipated changes can occur when fire is reintroduced. For example, the development of new fuel characteristics can change the patterns of fire mortality and associated ecological responses. To test the fire effects of delayed fire mortality (mortality initiated by fire that occurs subsequent to the fire year) in the Southern Appalachians, USA, we developed a fire‐effects model using both field studies and remote sensing. We then simulated these effects at a landscape scale to estimate broader ecological effects. Fire‐effects models that accounted for delayed mortality increased landscape biomass removed annually (~23%) and increased the number of sites with high light conditions (leaf area index < 4) when compared to simulations that only account for immediate mortality. While delayed mortality occurred across species and age classes, it was especially prevalent among older trees (>100 years old) and fire‐resistant species ( Quercus spp.). Overall, regeneration (trees <20 years old) changed very little, even with the inclusion of delayed mortality. This evidence suggests that, even when accounting for delayed mortality, individual fires are unlikely to shift the landscape composition toward the conditions of forests prior to fire exclusion and may even increase mesophication long term due to the loss of overstory dominant xeric trees.

Robbins, Zachary J.↗

Multidimensional Multiphysics Simulation of TRISO Particle Fuel

Multidimensional multiphysics analysis of TRISO-coated particle fuel using the BISON finite-element based nuclear fuels code is described. The governing equations and material models applicable to particle fuel and implemented in BISON are outlined. Code verification based on a recent IAEA benchmarking exercise is described, and excellant comparisons are reported. Multiple TRISO-coated particles of increasing geometric complexity are considered. It is shown that the code's ability to perform large-scale parallel computations permits application to complex 3D phenomena while very efficient solutions for either 1D spherically symmetric or 2D axisymmetric geometries are straightforward. Additionally, the flexibility to easily include new physical and material models and uncomplicated ability to couple to lower length scale simulations makes BISON a powerful tool for simulation of coated-particle fuel. Future code development activities and potential applications are identified.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructure and microchemistry changes at U-10Mo fuel/AA6061 cladding interfaces with varying hot isostatic pressing conditions

Monolithic uranium - 10 wt.% molybdenum (U-10Mo) is a promising high-assay low-enriched uranium fuel system for nuclear reactors used in research, medical isotope production, and remote power applications. During manufacturing, AA6061 cladding is bonded to the U-10Mo fuel plate via hot isostatic pressing, during which diffusion and fuel/cladding chemical interaction occurs at plate edges. Furthermore, the microstructure and microchemistry changes that occur at fuel/cladding interfaces are important to understand as a function of process parameters to develop a reliable fuel fabrication process and to meet the desired specifications. Here, microstructural and microchemical changes are studied using complementary electron microscopy and atom probe tomography for two manufactured fuel plates with varied hot isostatic pressing (HIP) parameters. Results highlight that modifying thermomechanical processing parameters significantly changed the interaction layer thickness between U-10Mo and AA6061 by an order of magnitude. In addition to this the distribution and concentration of elements (i.e., Al, Si, Mg) from cladding to fuel was also investigated.

36 MATERIALS SCIENCE↗

Italian hybrid and fission reactors scenario analysis

Italy is a country where a long tradition of studies both in the fission and fusion field is consolidated; nevertheless a strong public opinion concerned with the destination of the Spent Nuclear Fuel hinders the development of nuclear power. The possibility to a severe reduction of the NSF mass generated from a fleet of nuclear reactors employing an hypothetical fusionfission hybrid reactor has been investigated in the Italian framework. The possibility to produce nuclear fuel for the fission nuclear reactors with the hybrid reactor was analyzed too.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Center for Renewable Energy Science and Technology

The CREST research team conducted research that optimized catalysts used for the conversion of southwestern lignite into synthetic crude oil that can be shipped to nearby Texas refineries and power plants for development of transportation fuels and power generation. Research was also undertaken to convert any potential by-products of this process such as CO2 to useful chemicals and gases which could be recycled and used as feedstock to the synthetic fuel process. These CO2 conversion processes used light energy to drive the endogonic reduction reactions involved. The project was divided into two tasks: A CO2 Conversion Task, and a Catalyst Optimization Task. The CO2 Conversion task was aimed at developing molecular and solid state catalysts for the thermal, electro- and photocatalytic reduction of CO2 to reduced products such as simple feedstock compounds (e.g. CO, H2, CHOOH, CH2O, CH3OH and CH4). For example, the research team recycled CO that was developed from this Task and used it as a feedstock for the production of synthetic crude in the Catalyst Optimization Task. In the Catalyst Optimization Task, the research team conducted bench-scale experiments with the goal of reducing overall catalyst cost in support of several synthetic crude processes that had earlier been developed. This was accomplished by increasing the catalyst reactivity thus reducing required concentrations or by using less expensive metals. In this task the team performed parametric experiments in small scale batch reactors in an effort to improve catalyst reactivity and to lower cost. They also investigated catalyst robustness by testing lignite feedstocks that vary in moisture, h, and volatile content.

Billo, Richard↗

Differences In High Burnup Fuel Management Strategies to Minimize FFRD and Increase Economic Viability

The nuclear industry is pursuing approval of an increase in the length of the pressurized water reactor (PWR) cycle from 18 months to 24 months to reduce reactor downtime and enhance the economic competitiveness of nuclear energy. Such an increase in reactor cycle length will require that the maximum rod average burnup exceeds the current regulatory limit of 62 GWd/MTU, and it could peak at approximately 75 GWd/MTU, posing potential reactor safety and performance concerns. One such concern is that fuel fragmentation, relocation, and dispersal (FFRD) could occur during a severe loss-of coolant accident (LOCA) in which a fuel rod balloons and bursts, and pulverized fuel fragments are dispersed throughout the reactor’s primary coolant system. Previous analyses have identified which reactor operating conditions leave the core more susceptible to FFRD and have shown that FFRD susceptibility is strongly linked to fuel rod burnup and linear heat rate (LHR) history. The work described in this report uses an optimization strategy known as parallel simulated annealing (PSA) and a coarse mesh Purdue Advanced Reactor Core Simulator (PARCS) reactor physics model to develop two core fuel loading patterns, each with a different optimization objective. One core optimization maximized the core’s cycle length while still respecting regulatory limits on the radial peaking factor and soluble boron concentration with a peak rod average burnup of 75 GWd/MTU. The second optimization was aimed at minimizing FFRD susceptibility while still targeting a 24-month cycle length and respecting regulatory limits. PARCS model predictions were verified using the high-fidelity Virtual Environment for Reactor Applications (VERA). The two core designs were compared to highlight core design strategies to minimize FFRD susceptibility and to maximize economic viability.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗