Recrystallization and preferred orientation in single-crystal and polycrystalline copper in friction studies
Friction characteristics and interfacial recrystallization of single-crystal and polycrystalline copper sliding on aluminum oxide
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Friction characteristics and interfacial recrystallization of single-crystal and polycrystalline copper sliding on aluminum oxide
Mechanical testing and metallographic examination of aluminum to copper coldwelded joints after thermal exposure - SNAP-8 electrical terminal
Axial load fatigue endurance distributions of annealed oxygen free high conductivity copper specimens with cold worked surface layer tested at four stress levels
Stress rupture and creep properties analyzed in tungsten fiber reinforced copper composites
Recovery of deformed copper-palladium and gold- palladium alloys by isothermal and isochronal annealing, noting vacancy and interstitial migration
Yield and angular distribution of cesium ion- sputtered copper, noting dependence on angle of incidence, target temperature and energy
Thermionic work functions and electron emission S curves for contaminated copper surface in oxygen and cesium vapors, separate and mixed
For a simple diffraction pattern, the time required to calculate interplanar distances from measurements of the pattern is not excessive. If more than a few lines are present, however, or if several patterns are to be studied, it is very advantageous to have available a table giving interplanar spacings directly in terms of the linear measurements made on the film of the lines appearing on the diffraction pattern. The preparation of the table given here was undertaken when the expansion of research activities involving X-ray diffraction techniques indicated that such a table would greatly decrease the time required to analyze diffraction patterns. The table was prepared for use with K alpha(sub 1) radiation from the following target materials: molybdenum, copper, cobalt, iron, and chromium.
The NASA Electronic Parts and Packaging Program co-manager, requested the NASA Engineering and Safety Center (NESC) to compile a body of publicly available knowledge on copper (Cu) wire bonds and perform reliability testing and analysis on these bonds, including environment tests, sample destructive physical analysis, and bond pull/shear tests during environment test intervals. The goal was to understand the risks of using Cu wire bonds for space applications and develop guidelines on Cu bond pull/shear limits for NASA applications. This document contains the results of the NESC assessment.
In situ x-ray diffraction has been used to measure the shear strain (and thus strength) of single crystal copper shocked to Mbar pressures along the [001] and [111] axes. These direct shear strain measurements indicate shear strengths at these ultra-high strain rates (of order 10{sup 9} s{sup -1}) of a few GPa, which are both broadly in agreement with the extrapolation of lower strain-rate data and with non-equilibrium molecular dynamics simulations.
The NPDES permit issued to the Savannah River Site (SRS) in 2003 contained copper limits as low as six micrograms per liter. It also contained compliance schedules that provided SRS with anywhere from three to five years to select and implement projects that would enable compliance at several outfalls. Some outfall problems were much more difficult to correct than others. SRS personnel implemented several innovative projects in order to meet compliance schedule deadlines as inexpensively as possible. One innovation, constructing a humic acid feed system to increase effluent dissolved organic carbon (DOC) content, has proven to be very successful.
We report the direct measurement of individual grain boundary (GB) resistances and the critical role of GB structure in the increased resistivity in copper nanowires. By measuring both intra- and inter-grain resistance with a four-probe scanning tunneling microscope, large resistance jumps are revealed owing to successive scattering across high-angle random GBs, while the resistance changes at twin and other coincidence boundaries are negligibly small. The impurity distributions in the nanowires are characterized in correlating to the microstructures. The resistance of high symmetry coincidence GBs and the impurity contributions are then calculated using a first-principle method which confirms that the coincidence GBs have orders of magnitude smaller resistance than the high-angle random GBs.
The ILC Crab Cavity is positioned close to the IP and delivered luminosity is very sensitive to the wakefields induced in it by the beam. A set of couplers were designed to couple to and damp the spurious modes of the crab cavity. As the crab cavity operates using a dipole mode, it has different damping requirements from an accelerating cavity. A separate coupler is required for the monopole modes below the operating frequency of 3.9 GHz (known as the LOMs), the opposite polarization of the operating mode (the SOM), and the modes above the operating frequency (the HOMs). Prototypes of each of these couplers have been manufactured out of copper and measured attached to an aluminum nine cell prototype of the cavity and their external Q factors were measured. The results were found to agree well with numerical simulations.
Recent copper wire array shots on Z, when spectroscopically analyzed on a spatially-averaged basis, appear to have achieved ion densities near 10{sup 21} cm{sup -3}, electron temperatures of 1.25 keV, and K-shell radiating participation of 70-85% of the load mass. However, pinhole images of the shots reveal considerable structure, including several well-defined intensely radiating 'bright spots', which may be due to enhanced density, temperature, or some combination of the two. We have analyzed these individual spots on selected shots, using line-outs of their spectrum and inferred powers based on their images. We compare the properties of these spots (are they dense, hot, or both?), and examine their effect on inferring the radiating mass.
The effects of loading kinetics on the damage evolution in high purity copper samples are summarized as follows: The combination of the energy supplied by the shock impulse (peak stress) and the time spent in it dissipation seem to be responsible for the characteristics of the damage fields. For an increasing coupled parameter of energy*time, more damage was predicted, as well as experimentally observed; As more energy (higher peak stress) was dissipated for longer periods of time (lower decompression rate), the damage fields evolved from early stages of damage, in the form of void nucleation and initial void growth, to the later stages of void coalescence.
A number of plate impact experiments have been conducted on high purity polycrystalline tantalum and copper samples using graded flyer plate configurations to alter the loading profile. These experiments are designed in a way so that a broad range of damage regimes are probed. The results show that the nucleation of damage primarily occurs at the grain boundaries of the materials. This affords us the opportunity to propose a porosity damage nucleation criterion which begins to account for the length scales of the microstructure (grain size distribution) and the mechanical response of the grain boundary regions (failure stress distribution). This is done in the context of a G-T-N type model for the ductile damage and failure response of both the materials examined. The role of micro-inertial effects on the porosity growth process is also considered.
We report the design and experimental data for a copper prototype of a superconducting radio-frequency (SRF) accelerator module. The five-cell module has an incorporated photonic band gap (PBG) cell with couplers. The purpose of the PBG cell is to achieve better higher order mode (HOM) damping, which is vital for preserving the quality of high-current electron beams. Better HOM damping raises the current threshold for beam instabilities in novel SRF accelerators. The PBG design also increases the real-estate gradient of the linac because both HOM damping and the fundamental power coupling can be done through the PBG cell instead of on the beam pipe via complicated end assemblies. First, we will discuss the design and accelerating properties of the structure. The five-cell module was optimized to provide good HOM damping while maintaining the same accelerating properties as conventional elliptical-cell modules. We will then discuss the process of tuning the structure to obtain the desired accelerating gradient profile. Finally, we will list measured quality factors for the accelerating mode and the most dangerous HOMs.
Presentation describes research into spall behavior of single crystal copper.