Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Composition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Toughening of Boron Carbide Composites by Hierarchical Microstructuring

Due to a unique combination of properties including high hardness, low density, chemical and thermal stability, semi-conductivity, and high neutron absorption, boron carbide (B4C) is a potential candidate for various applications involving extreme environment. However, B4C’s current application is limited because of its low fracture toughness. In this study, a hierarchical microstructure design with features including TiB2 grains and graphite platelets was used to toughen B4C by simultaneously utilizing multiple toughening mechanisms including crack deflection, bridging, and micro-crack toughening. Using field-assisted sintering technology (FAST), B4C composites with dense and hierarchical microstructure were fabricated. Previously, the fracture toughness of fabricated B4C composites was measured at micro-scale using micro-indentation to have up to 56% improvement. In this work, the B4C composites’ fracture toughness was characterized at macro-scale using four-point bending methods and compared with previous results obtained at micro-scale. Micromechanics modeling of fracture behaviors for B4C-TiB2 composites was also performed to evaluate the contributions from experimentally observed toughening mechanisms. From four-point bending tests, B4C composites reinforced with both TiB2 grains (~15 vol%) and graphite platelets (~8.7 vol%) exhibited the highest fracture toughness enhancement from 2.38 to 3.65 MPa∙m^(1/2). The measured values were lower than those obtained using micro-indentation but maintained the general trends. The discrepancy between the indentation and four-point bending test results originated from the complex deformation behaviors triggered by the high contact load during indentation tests. Through micromechanics modeling, introduced thermal residual stress due to thermal expansion mismatch between B4C and TiB2, and weak interphases at B4C-TiB2 boundaries were identified as the main causes for experimentally observed toughness enhancement. These results proved the effectiveness of hierarchical microstructure designs for B4C toughening and can provide reference for the future design of B4C composites with optimized microstructures for further fracture toughness enhancement.

composites↗

Thermal Response of Thermoplastic Composite Tape During In-situ Consolidation Automated Fiber Placement Using a Laser Heat Source

Composite materials have tremendous potential in the design and manufacture of commercial aircraft due to their high strength-to-weight and stiffness-to-weight properties. However, the use of composite materials is currently limited by high cost and long manufacturing time. The National Aeronautics and Space Administration (NASA) initiated the Hi-rate Composite Aircraft Manufacturing (HiCAM) project to investigate promising composite processing technologies with a goal of vastly improving composite commercial aircraft manufacturing rate (4-6x faster than current production rates). Laser assisted automated fiber placement (AFP) of thermoplastics is a key technology that could increase speed of composite manufacturing, but the technology has not been fully developed. In-situ consolidation AFP of thermoplastics (ICAT) could reduce time and cost even further by eliminating the time and equipment required for post-consolidation. In this work, the thermal response of laser heated ICAT was investigated using forward looking infrared (FLIR) and embedded thermocouples (TCs) to better understand fusion between layers (autohesion). Detailed explanation of the algorithm to combine FLIR and TC data will be presented. In addition, the effect of robot speed on time above melting temperature was quantified.

Laser Heating↗

Highly Thermally Conductive Hybrid Carbon Fiber Polymer Composite for Radiator Application

Carbon fiber (CF) reinforced polymer composites have been used for aerospace structures because they have low mass, high specific strength, high specific stiffness, and low life-cycle maintenance compared to aluminum alloys. However, due to their relatively low thermal conductivity, pristine CF polymer composites fail to provide effective heat flow for certain applications such as heat exchange systems and radiators. The technology described in this paper provides novel CF polymer composites that possess high thermal conductivity by incorporating pyrolytic graphite sheets (PGS). The thermal conductivities of novel hybrid PGS/CF polymer composites were measured to be about 10 to 30 times higher than that of pristine CF polymer composite, and about two times higher than that of aluminum alloy 6061. This new material with sufficient thermal conductivity is applicable to composite radiators of heat exchange systems.

Thermal Conductivity↗

Advanced Composite Solar Sail System (ACS3) Mission Update

The Advanced Composite Solar Sail System (ACS3) will be the first practical solar sail for the National Aeronautics and Space Administration. [1] ACS3 will also be the first spaceflight demonstration of NASA compact deployable composite boom technology.[2] The primary mission objective of ACS3 will be to deploy and characterize an 80-m2 composite boom structure solar sail technology in low Earth orbit. Extended mission goals will be to demonstrate controlled solar sailing flight via a series of orbit raising and lowering maneuvers. Target mission orbit is a 1000 km x 1000 km midnight-noon sun-synchronous orbit. Launch of ACS3 is scheduled for July 2023 with sail deployment in September 2023. Mission duration is expected to be six to nine months. The ACS3 solar sail vehicle is a 12U Cubesat consisting of a bus module, containing flight and solar sail control avionics, and a solar sail module, containing the composite booms and metallized polymer solar sail membranes of the solar sail structure stowed within a boom deployer mechanism. A four-camera instrument suite for 360-degree imaging of the ACS3 solar sail during and after deployment is also housed within the bus module. The ACS3 80-m2 solar sail design is a sub-scale version of an intermediate-size 500-m2 solar sail using NASA deployable composite boom technology. The sail consists of four metallized 2-m thick polyethylene naphthalate (PEN) 20-m2 triangular quadrants supported by four 7-m long lenticular cross-section composite booms. Booms are flattened and co-coiled for stowage within a tape-spool driven deployer mechanism. Total mass of the ACS3 space vehicle including solar sail is 16 kg. An overview of the ACS3 mission and mission systems will be provided in this presentation. This overview will include descriptions of the solar sail structures and materials technology used with ACS3, and discussion of the scalability and extensibility of the ACS3 solar sail to future larger-scale solar sailing mission requirements. An update on progress towards the launch of ACS3 in July 2023 will also be provided. References [1] https://www.nasa.gov/directorates/spacetech/small_spacecraft/ACS3 [2] https://www.nasa.gov/directorates/spacetech/game_changing_development/projects/dcb

Solar sail↗

A Procedure to Quantify Interlaminar Damage in Refractory Composites by In-Situ Micro-X-Ray Computed Tomography

Refractory composites are relevant for hot-structure applications on re-entry vehicles. To develop optimized high-performance hot structures, accurate material property data is required. Material properties that often limit design in two-dimensional (2-D) composites are interlaminar strengths. A better understanding of the failure mechanisms for interlaminar shear (ILS), interlaminar tension (ILT), and curved-beam interlaminar tension (CB-ILT) tests can provide insight on improving the design and fabrication of refractory composites. In-situ tests were performed to capture the progressive failure in American Society for Testing and Materials (ASTM) sized ILS (ASTM D3846), ILT (ASTM D7291), and CB-ILT (ASTM D6415) specimens. Before measuring internal damage of refractory composites specimens, the methodology of the test setup warrants a complete and thorough discussion. Detail on the test procedure, test stand design, micro-x-ray computed tomography (CT) configuration, data processing, and CT system uncertainty is discussed. Through keeping the many parameters of the CT system consistent, the uncertainty of the CT system was minimized, optimizing the quality of measurements. The overall quality of a CT scan can be quantified by three metrics: voxel resolution, minimal voxel resolution feature detection, and directional variability. A better understanding of the progressive failure mechanisms of refractory composites is provided by the results of both the present discussion and the one found in the accompanying paper titled “Analysis of Interlaminar Damage in Refractory Composites by In-Situ Micro-X-Ray Computed Tomography”.

In-situ micro-x-ray CT↗

Improvements to Stitching Controls for Manufacturing Advanced Stitched Composites

Stitched composites have been extensively studied and have been shown to have benefits over unstitched composites for stiffened structures, including improved damage tolerance, reduced weight, and fewer fasteners. These benefits make stitched composites attractive from a performance perspective, however, the nature of stitching the preforms prior to infusion includes additional manufacturing steps and equipment compared to conventional resin infusion. Stitching of composite material structures at NASA Langley Research Center (LaRC) is performed at the Integrated Structural Assembly of Advanced Composites (ISAAC) facility using control algorithms developed by the lead author. Two deficiencies have been identified in the current control algorithms, and mitigations for these deficiencies were developed within the Hi-Rate Composite Aircraft Manufacturing (HiCAM) project and are presented herein. First, decoupling stitch translation and rotation takes more time for stitching since two robot operation control steps are executed for each stitch. Therefore, a method was developed to determine when to decouple the translation and rotation for stitching, which reduces stitch time by decoupling the operation control steps only when necessary to execute the stitch properly. Second, a correction to the sideslip stitching approach that eliminates a significant portion of the pre- and post-stitching activities was developed. The developed method adjusts the sideslip stitch angle based on the rotations of previous stitches to ensure that the width of the stitching seam remains constant along its length. Constant seam width eliminates observed overlap of the insertion and catcher thread portions for highly curved paths, which maintains the desired uniformity of through-the-thickness architecture along the seam and eliminates the local degradation of properties where the insertion needle is too close to, or crosses, the catcher needle portion of the seam.

stitching↗

Composite Materials under Extreme Radiation and Temperature Environments of the Next Generation Nuclear Reactors

In the nuclear energy renaissance, driven by fission reactor concepts utilizing very high temperatures and fast neutron spectra, materials with enhanced performance that exceeds are expected to play a central role. With the operating temperatures of the Generation III reactors bringing the classical reactor materials close to their performance limits there is an urgent need to develop and qualify new alloys and composites. Efforts have been focused on the intricate relations and the high demands placed on materials at the anticipated extreme states within the next generation fusion and fission reactors which combine high radiation fluxes, elevated temperatures and aggressive environments. While nuclear reactors have been in operation for several decades, the structural materials associated with the next generation options need to endure much higher temperatures (1200 C), higher neutron doses (tens of displacements per atom, dpa), and extremely corrosive environments, which are beyond the experience on materials accumulated to-date. The most important consideration is the performance and reliability of structural materials for both in-core and out-of-core functions. While there exists a great body of nuclear materials research and operating experience/performance from fission reactors where epithermal and thermal neutrons interact with materials and alter their physio-mechanical properties, a process that is well understood by now, there are no operating or even experimental facilities that will facilitate the extreme conditions of flux and temperature anticipated and thus provide insights into the behaviour of these well understood materials. Materials, however, still need to be developed and their interaction and damage potential or lifetime to be quantified for the next generation nuclear energy. Based on material development advances, composites, and in particular ceramic composites, seem to inherently possess properties suitable for key functions within the operating envelope of both fission and fusion reactors. In advanced fission reactors composite materials are being designed in an effort to extend the life and improve the reliability of fuel rod cladding as well as structural materials. Composites are being considered for use as core internals in the next generation of gas-cooled reactors. Further, next-generation plasma-fusion reactors, such as the International Thermonuclear Experimental Reactor (ITER) will rely on the capabilities of advanced composites to safely withstand extremely high neutron fluxes while providing superior thermal shock resistance.

36 MATERIALS SCIENCE↗

Impact of Compositional Fluctuation on Dislocations in Metamorphic III-V Solar Cells Revealed by Cathodoluminescense Spectrum Imaging

Compositionally graded buffers (CGBs) are essential components of high-efficiency III-V inverted metamorphic solar cells. High-quality CGBs with low defect densities are a requirement for high device efficiencies. In this work we use cathodoluminescence spectrum imaging to investigate the effect of growth conditions on the material properties of AlyGa1-x-yInxAs CGBs with xIn = > 0.30. We find that significant compositional fluctuation exists in these materials, and that it correlates with the distribution of threading dislocations in the CGBs. Threading dislocations collect in regions with large compositional fluctuation, implying that concurrent strain fluctuations in these regions restrict dislocation motion. Thus, the compositional fluctuation leads to elevated threading dislocation densities that degrade CGB quality. We investigate the effectiveness of specific growth conditions at suppressing compositional fluctuation and limiting threading dislocation density, and find that CGBs grown at high temperatures with high Al-content exhibit the lowest defect densities. We also demonstrate that use of a high V/III ratio also suppresses compositional fluctuation and defect density. These materials insights lead directly to the development of metamorphic Ga1-xInxAs solar cells grown on AlyGa1-x-yInxAs CGBs with improved device efficiency.

14 SOLAR ENERGY↗

Nanoscale Three-Dimensional Imaging of Degradation in Composite Si-Containing Anodes

The use of silicon (Si) in next-generation lithium-ion battery (LIB) anodes has the potential to dramatically improve electrochemical performance over current LIB graphite (Gr) anodes, due to silicon’s higher specific capacity.1 However, widespread implementation of Si-containing anodes is inhibited by issues such as significant Si volume expansion during lithiation and an unstable solid-electrolyte interphase (SEI), resulting in unreliable performance and poor cycle life. Currently, composite anodes with both Si and graphite active materials are used to increase capacity and mitigate some of the limitations associated with Si. In composite electrodes with a heterogeneous distribution of components with varying electrical properties (including Si, Gr, conductive carbon additive, and binder), it is important to understand the local distribution of each component to correlate with electrochemical processes, particularly localized degradation and heterogeneous aging, and to optimize performance. To investigate Si-containing composite anodes in the nanoscale, we use scanning spreading resistance microscopy (SSRM), a form of scanning probe microscopy (SPM) that probes local electronic resistivity. By examining the intrinsic electronic resistivity contrast between the anode components, separate phases can be distinguished and understood within the composite structure.2 This work studies the effect of electrochemical cycling in two different electrolytes on component distribution and aging by comparing the electrical and structural evolution of composite Si-graphite electrodes and SEI before and after charge-discharge cycling. 1. W. J. Zhang. A review of the electrochemical performance of alloy anodes for lithium-ion batteries J. Power Sources 196 13–24 (2011). 2. C. Stetson, Z. Huey, A. Downard, Z. Li, B. To, A. Zakutayev, C.-S. Jiang, M. Al-Jassim, D. Finegan, S.-D. Han and S. DeCaluwe: Three-Dimensional Mapping of Resistivity and Microstructure of Composite Electrodes for Lithium-Ion Batteries. ACS Nano Letters Accepted (2020).

ADVANCED PROPULSION SYSTEMS↗

The aqueous corrosion behavior of technetium - Alloy and composite materials

Metal waste forms are under study as possible disposal forms for technetium and other fission products. The alloying of Tc is desirable to reduce the melting point of the Tc-containing metal waste form and potentially improve its corrosion resistance. Technetium-nickel composites were made by mixing the two metal powders and pressing the mixture to make a pellet. The as-pressed composite materials were compared to sintered composites and alloys of identical composition in electrochemical corrosion tests. As-pressed samples were not robust enough for fine polishing and only a limited number of corrosion tests were performed. Alloys and composites with 10 wt% Tc appear to be more corrosion resistant at open circuit than the individual components based on linear polarization resistance and polarization data. The addition of 10 wt% Tc to Ni appears beneficial at open circuit, but detrimental upon anodic polarization. Qualitatively, the polarizations of 10 wt% Tc alloys and composites appear like crude addition of Tc plus Ni. The 1 wt% Tc alloys behave like pure Ni, but some effect of Tc is seen upon polarization. Cathodic polarization of Tc by Ni appears feasible based on open circuit potential measurements, however, zero resistance ammetry and solution measurements are necessary to confirm cathodic protection.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fabrication and Testing of Complex Silicon Carbide Composite Structures

The ability to fabricate larger complex silicon carbide composites is an enabling technology for advanced reactors. Processing techniques to make complex SiC/SiC structures must be versatile enough to facilitate fabrication of both very large components (>1 m), as well as very small feature sizes (<1 mm), minimize the amount of machining required to complete the final part, and must also provide composite material with similar performance to bulk properties previously established for planar SiC/SiC composite material. This paper presents results on fabrication of complex silicon carbide structures and targeted testing aimed specifically at understanding how complex features impact composite performance. Silicon carbide (SiC) and silicon carbide matrix, silicon carbide fiber-reinforced composites (SiC/SiC) are a strong candidate for cladding and core structure used in advanced reactor concepts such as General Atomics' (GA) Energy Multiplier Module (EM{sup 2}) as well as accident tolerant fuel (ATF) in LWRs. SiC retains its strength up to very high temperatures, is stable under irradiation, and shows favorable neutronics and oxidation resistance compared to alloy alternatives. However, unlike metals, SiC cannot be easily machined, formed or welded to make the more complex core components needed to fully realize the benefits of advanced high temperature reactors. TEP processing provides an appealing route to achieving SiC/SiC composite structures with enhanced feature complexity. This is a critical development in the maturation of SiC/SiC for in-core structural materials in advanced reactors. This processing route provides an avenue to make large, dense, complex structures. Experiments have shown retention of strength and pseudo-ductility with hole spacing as small as 4 mm with potential for still smaller feature spacing. The results indicate that feature spacing is not limited by processing effects, but instead by the fiber architecture. The lower limit of feature spacing will likely have implications on potential core loading limits in advanced nuclear reactors utilizing SiC/SiC. (authors)

36 MATERIALS SCIENCE↗

Thermal Diffusivity Measurement of Irradiated SiC-SiC Composite Material

Silicon Carbide fiber and matrix composite (SiC-SiC) is being considered as a fuel cladding candidate because of its high melting point, low susceptibility to corrosion, good thermal and mechanical shock resistance, and low degradation of mechanical properties under irradiation. The thermal properties of SiC-SiC composite depend heavily on the fabrication process, thus cannot be simply referenced from available database. Similarly, the influence of irradiation on SiC-SiC composite thermal properties needs to be measured to provide general trends of property degradation. For ion irradiated samples, the damaged layer is only a few to a few tens of micrometers. It is impossible to directly measure the bulk property change of a SiC-SiC composite because of the thin, damaged layer. This paper focuses on a methodology that is based on microscale measurement of fiber and matrix properties to determine the overall bulk property change due to ion irradiation. Laser-based photothermal reflectance technique is one of the ideal methods to measure local thermal conductivity and diffusivity with high spatial resolution. The main principle of this technique is to heat the solid sample using an intensity-modulated laser, and scan the sample with a constant intensity continuous-wave (CW) laser to detect the phase lag of the thermal wave propagation. On bulk, isotropic material, if the heating laser intensity is modulated as a sine wave, thermal diffusivity of the sample can be derived from the phase lag, scan distance and modulation frequency in a straight forward manner. By using more specific analytical models, thermal conductivity and diffusivity in complicated cases, such as layered structure materials, composite materials, and/or anisotropic materials, are measurable as well. In this work, a new measurement approach of SiC-SiC composite thermal diffusivity is presented. Due to the micrometer spatial resolution of the photothermal reflectance technique, the measurements are performed locally on fibers along both radial and axial directions, and on the matrix. The influence of Silicon ion irradiation (75 MeV, 10 dpa) is then examined by comparing the experimental results of samples before and after irradiation. (authors)

36 MATERIALS SCIENCE↗

Comparison of Thermal Diffusivity Degradation of Irradiated Zirlo and SiC-SiC Composite

Zirlo (Zircaloy cladding material from Westinghouse) has been widely used as the fuel cladding material in Light Water Reactors because of its high melting point, low susceptibility to corrosion, good thermal and mechanical shock resistance, and low degradation of mechanical properties under irradiation. But as Zirlo reacts with water at high temperature, which can trigger serious accidents, efforts have been made to explore better candidates to replace Zirlo in the water-cooled reactors. SiC-SiC composite is considered as one of the most viable options due to its comparable mechanical performances and corrosion resistance. However, one of the most important properties, thermal diffusivities of both Zirlo and SiC-SiC composite, and their degradation after irradiation, are not well known yet. Ion-irradiated samples are used to study the thermal property degradation caused by irradiation instead of the neutron-irradiated ones due to the significantly lower radioactivity. The microstructural damage is estimated from the software simulation SRIM/TRIM based on the energy and fluence of the ion, and the target material, and represented by DPA (displacement by atom). Different from neutron-irradiated samples, the damaged layer of ion-irradiated samples is only a few to a few tens of micrometers thick, and the damage is depth dependent. It is impossible to directly measure the bulk property change, and a microscale measurement technique is necessary. Laser-based photothermal reflectance technique is one of the ideal methods to measure local thermal conductivity and diffusivity with high spatial resolution. The main principle of this technique is to heat the solid sample using an intensity-modulated laser, and scan the sample with a constant intensity continuous-wave (CW) laser to detect the thermal wave propagation. On bulk, isotropic material, if the heating laser intensity is modulated as a sine wave, thermal diffusivity of the sample can be derived from the phase lag of the thermal wave, scan distance and modulation frequency in a straight forward manner. By using more specific analytical models, thermal conductivity and diffusivity in complicated cases, such as layered structure materials, composite materials, and/or anisotropic materials, are measurable as well. In this work, thermal diffusivity of the light damage layer of the post-irradiation Zirlo and SiC-SiC composite are measured and compared. The Zirlo sample is irradiated by Ni{sup 9+} ion, and SiC-SiC composite material is irradiated by Si{sup 7+} ion. The peak DPA of both sample is similar as ∼10. For ion-irradiated materials, DPA is known to increase with depth before it reaches the peak, and then sharply drop to zero. In term of light damage layer in this manuscript, we mean by the layer with a DPA smaller than 5% maximum value. In this layer DPA increases slowly and smoothly with depth, and the structure and thus thermal properties are more spatially uniform. For the SiC-SiC composite, the measurements are separately conducted on fibers along radial or axial direction, and on the matrix. Our measurement results show that with similar microstructural damage, thermal diffusivity of matrix SiC reduces more significantly than that of Zirlo. For fiber SiC that has a much lower thermal diffusivity than the matrix SiC before irradiation, the post-irradiation effect on thermal diffusivity is not obvious.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A revisit to high-rate mode-II fracture characterization of composites with Kolsky bar techniques.

Nowadays composite materials have been extensively utilized in many military and industrial applications. For example, the newest Boeing 787 uses 50% composite (mostly carbon fiber reinforced plastic) in production. However, the weak delamination strength of fiber reinforced composites, when subjected to external impact such as ballistic impact, has been always potential serious threats to the safety of passengers. Dynamic fracture toughness is a critical indicator of the performance from delamination in such impact events. Quasi-static experimental techniques for fracture toughness have been well developed. For example, end notched flexure (ENF) technique, which is illustrated in Fig. 1, has become a typical method to determined mode-II fracture toughness for composites under quasi-static loading conditions. However, dynamic fracture characterization of composites has been challenging. This has resulted in conflictive and confusing conclusions in regard to strain rate effects on fracture toughness of composites.

36 MATERIALS SCIENCE↗

Sources and composition of submicron organic mass in marine aerosol particles

Recent studies have proposed a variety of interpretations of the sources and composition of atmospheric marine aerosol particles (aMA) based on a range of physical and chemical measurements collected during open-ocean research cruises. To investigate the processes that affect marine organic particles, this study uses the characteristic functional group composition (from Fourier transform infrared (FTIR) spectroscopy) of aMAP from five ocean regions to show that: (i) The organic functional group composition of aMAP that can be identified as atmospheric primary marine (ocean-derived) aerosol (aPMA) is 65±12% hydroxyl, 21±9% alkane, 6±6% amine, and 7±8% carboxylic acid functional groups. Contributions from photochemical reactions add carboxylic acid groups (15%-25%), shipping effluent in seawater and ship emissions add additional alkane groups (up to 70%), and coastal emissions mix in alkane and carboxylic acid groups from coastal pollution sources. (ii) The organic composition of aPMA is nearly identical to model generated primary marine aerosol particles (gPMA) from bubbled seawater (55% hydroxyl, 32% alkane, and 13% amine functional groups), indicating that its overall functional group composition is the direct consequence of the organic constituents of the seawater source. (iii) While the seawater organic functional group composition was nearly invariant across all three ocean regions studied, the gPMA alkane group fraction increased with chlorophyll-a concentrations (r = 0.79). gPMA from productive seawater had a larger fraction of alkane functional groups (35%) compared to gPMA from non-productive seawater (16%), likely due to the presence of surfactants in productive seawater that stabilize the bubble film and lead to preferential drainage of the more soluble (lower alkane group fraction) organic components. gPMA has a hydroxyl group absorption peak location characteristic of monosaccharides and disaccharides, where the seawater OM hydroxyl group peak location is closer to that of polysaccharides. This may result from the larger saccharides preferentially remaining in the seawater during gPMA and aPMA production

54 ENVIRONMENTAL SCIENCES↗

SCOPING MELTING STUDIES OF HIGH ALUMINA WASTE GLASS COMPOSITIONS

Glass property models will be used at the Hanford Tank Waste Treatment and Immobilization Plant to formulate durable high-level waste glasses for disposal. A major effort is focused on expanding glass property models to cover a broader range of wastes and higher waste-loaded glasses. As a part of this effort, a statistically designed matrix of high-alumina glass compositions was developed. Forty five compositions were selected from the matrix to evaluate glass properties. Of these compositions, thirty three produced homogeneous glasses. The other twelve compositions contained segregated phases and high crystallinity; these were iteratively modified in an attempt to produce homogeneous glass samples while altering the original composition as little as possible. This paper focuses on the characterization of the twelve inhomogeneous compositions and their modifications using X-ray diffraction, scanning electron microscopy, and energy dispersive spectroscopy.

Kroll, Jared O.↗

Optical Evidence of Compositional Fractioning between Plasma‐Condensed and Melt Pool Matter

Control of multicomponent alloys during welding is challenging because it lacks a real‐time understanding of composition. The optical emissions of plasma formed during laser‐induced metal welding correlate with the composition of particles ejected from the melt pool. Plasma emissions observed in this study contain large iron, manganese, chrome, and copper signatures, which match the composition of emitted particles. Particles recovered closest to the melt pool exhibit a core–shell morphology that is composed of iron‐manganese‐chrome intermetallic cores within copper shells. Particles collected farther from the melt pool, do not share this core–shell morphology, though similar elemental compositions are observed. The correlation between plasma optical emissions and particle composition can be used to predict the composition of the melt pool, allowing for real‐time welding and sintering control.

36 MATERIALS SCIENCE↗

Discovery of New Oxygen Evolution Reaction Electrocatalysts by Combinatorial Investigation of the Ni-La-Co-Ce Oxide Composition Space

We report a new family of earth abundant electrocatalysts for the oxygen evolution reaction (OER) discovered via high throughput screening of 1771 discrete metal oxide compositions covering the nickel-lanthanum-cobalt-cerium composition space. The catalytic performance of each of these compositions was measured under conditions applicable to distributed solar fuels generation using a three-electrode scanning drop electrochemical cell. These high throughput measurements show enhanced activity for catalyst compositions containing 20-65 metal atom % Ce. The catalytic activity and stability of a representative highly active composition (Ni 0.1 La 0.1 Co 0.3 Ce 0.5 )O x was verified by standard rotating disc electrochemistry. Catalysts of this composition showed stable operational performance at 10 mA cm -2 for 2 h and survived a 100 h endurance test in a testbed electrolyzer.

10 SYNTHETIC FUELS↗