Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Composite”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88

Preparation and Oxidation Performance of a NiCoCrAlYSiHf + NiAl Composite Coating Deposited by Arc Ion Plating and Magnetron Sputtering Techniques

A NiCoCrAlYSiHf+NiAl composite coating was deposited onto a second-generation single-crystal superalloy René N5 by methods of arc ion plating and magnetron sputtering. After vacuum annealing, the composite coating exhibited a gradient distribution of elements, in which Al was enriched in outer layer and Cr was enriched in inner layer. Compared with conventional NiCoCrAlYSiHf and β-NiAl coatings, the composite coating was evaluated in isothermal and cyclic oxidation tests at 1100 °C in ambient air. The results showed that the oxidation rate of the composite coating was lower than that of NiCoCrAlYSiHf coating. Meanwhile, the extent of interdiffusion between coating and substrate in the composite coating was slighter compared with that in the β-NiAl coating. Microstructure evolutions of the composite coating after annealing and further oxidation test are investigated.

36 MATERIALS SCIENCE↗

Effect of Prolonged Ultraviolet Radiation Exposure on the Blast Response of Fiber Reinforced Composite Plates

An experimental study with corresponding numerical simulations was conducted to evaluate the blast response of composite plates after prolonged exposure to ultraviolet radiation. Two composite materials were used in this study, namely carbon fiber/epoxy and glass fiber/vinyl ester. The composite materials consisted of four unidirectional fiber plies oriented in a [± 45°]s layup. The plates were placed in a QUV Accelerated Weathering Tester for 500 h of exposure on each face, totaling 1000 h of ultraviolet radiation exposure, equivalent to 2.5 MJ/m{sup 2} of energy. The QUV Accelerated Weathering Tester was equipped with eight UVA-340 lamps to provide real service life exposure conditions. Material characterization experiments were performed on virgin specimens, as well as specimens exposed to ultraviolet radiation for 1000 h to determine its effect on the mechanical properties of the composites. Blast experiments were conducted on the composite plates to investigate the dynamic response before and after exposure to ultraviolet radiation. The plates were clamped on all edges and subjected to an air blast using a shock tube apparatus. Three-dimensional digital image correlation was coupled with high-speed photography to obtain full-field displacements of the specimens during blast loading. Furthermore, three piezoelectric pressure transducers were mounted on the shock tube apparatus and utilized to measure the pressure history of the shock wave loading. The quasi-static material characterization showed that the tensile modulus E{sub 1} had minimal change after exposure to ultraviolet radiation for 1000 h. However, matrix-dominated properties such as the in-plane shear modulus G{sub 12} increased after exposure to ultraviolet light for both the carbon and glass fiber composites, which resulted in lower out-of-plane displacements during blast loading. For the carbon fiber plates, the forced vibration frequency induced by the transverse blast load was higher in plates exposed to ultraviolet radiation when compared to virgin specimens. However, for the glass fiber plates exposed to ultraviolet radiation, the forced vibration frequency decreased when compared to virgin specimens. Finally, the finite element simulations were in good agreement with the experimental results. The simulations revealed that the glass fiber plates exposed to ultraviolet radiation had higher failure strains at the boundary than virgin specimens, despite having higher stiffness. A parametric study in which higher loading was simulated also showed that the glass fiber plates experienced more damage after 1000 h of ultraviolet radiation exposure.

36 MATERIALS SCIENCE↗

Fabrication, Microstructures, and Properties of 50 vol.% SiCp/6061Al Composites via Hot Pressing

Nearly fully dense 50 vol.% SiCp/6061Al composites were fabricated via hot pressing (HPing) at temperatures ranging from 610 to 650 °C, with the axial load and holding time fixed as 25 MPa and 120 min, respectively. The interfacial reactions, microstructures, and properties of the SiCp/Al alloy were studied. The interface reaction between SiCp and the Al alloy was suppressed at annealing temperatures of 620 °C and below; however, the reaction intensified as the annealing temperature increased, producing Al{sub 4}C{sub 3}, Si, and Mg{sub 2}Si. With an increase in HPing temperature from 610 to 630 °C, the 6061Al alloy melted and gradually filled the pores in the SiC particles under the applied load. The density, bending strength, and thermal conductivity (TC) of the composites increased, whereas the coefficient of thermal expansion (CTE) of the composites decreased. With an increase in HPing temperature increased from 630 to 650 °C, the 6061Al alloy melt leaked through the sintered bodies, resulting in the microstructural degradation and property reduction of the composites. The 50 vol.% SiCp/6061Al composites fabricated by HPing at 630 °C exhibited optimal comprehensive properties [bending strength, 332.4 MPa; TC, 186.3 W(m K){sup −1}; and CTE, 7.9 × 10{sup −6}/°C (20-100 °C)], which were attributed to the highest relative density and the best SiCp/Al interfacial structure of the composites.

36 MATERIALS SCIENCE↗

Fabrication and Characterization of A5083-WC-Al{sub 2}O{sub 3} Surface Composite by Friction Stir Processing

In this study, WC-Al{sub 2}O{sub 3} ceramic composite was incorporated into Al5083 to produce a surface composite by friction stir processing (FSP), and the microstructure, hardness and wear properties of Al5083-WC-Al{sub 2}O{sub 3} surface composite were evaluated. Optical microscopy of FSPed samples showed grain refinement in the stir zone. The addition of WC-Al{sub 2}O{sub 3} particles as well as increase in FSP pass number had a considerable effect on grain refinement, and the grain size of Al5083 base metal of 36 µm reduced to 11 µm for Al5083-WC-Al{sub 2}O{sub 3} surface composite after four passes. The SEM observation of the surface composite revealed that the WC-Al{sub 2}O{sub 3} particles distributed homogenously in the matrix and by increasing the FSP passes, the initial agglomerates of mechanochemically synthesized WC-Al{sub 2}O{sub 3} powders could be fractured. Microhardness evaluation showed a substantial improvement by adding WC-Al{sub 2}O{sub 3} particles and increase in FSP pass number. The maximum microhardness value of 101 HV belonged to surface composite after four passes, while the microhardness of the base metal was 65 HV. Wear test results revealed enhanced tribological behavior with a similar trend of microhardness values. Scanning electron microscopy tests revealed both adhesive and abrasive wear mechanisms on the surface of the wear test specimens.

36 MATERIALS SCIENCE↗

Effects of Particle Characteristic Parameters on the Electrical Conductivity of TiB{sub 2}/Cu Composites: A Modified Model for Predicting Their Electrical Conductivity

High-strength and highly conductive copper matrix composites can not only maintain excellent electrical and thermal conductivity but also enhance the strength and hardness of materials, showing that composites have a bright future for development. Predictions of the effective electrical conductivity of copper matrix composites disagree with experimental data due to the dependence of the composites on several factors. Most prediction models simply consider the influence of the particle volume fraction on conductivity. In the present study, the influence of the volume fraction and the size of the TiB{sub 2} particle on the electrical conductivity of TiB{sub 2}/Cu composites are investigated. The obtained electrical conductivity results correlate with the volume fraction, size, and distribution of particles in a pure copper matrix. A modified model for predicting the electrical conductivity is proposed where the particle spacing parameters are introduced into the existing Maxwell model. The particle spacing parameter, as a fitting parameter, fits the experimental data of the copper matrix composites excellently.

36 MATERIALS SCIENCE↗

Corrosion Protection of Cu Electrical Cable by W-Ni Composite Coatings Doped with TiO{sub 2} Nanoparticles: Influence of Pulse Currents

W-Ni-TiO{sub 2} nano-composite layers were electrodeposited on copper surface by both direct (DC) and pulse (PC) currents. The copper substrates are samples from the main electrical cable used for the Renault K-Z (the latest 100% electric vehicle). In order to investigate coating morphology, atomic force microscopy was used, while energy-dispersive x-ray analysis was applied to determine nano-composite composition. Based on surface morphology, the W-Ni-TiO{sub 2} (DC) alloy surface was covered by massive agglomerates, especially when the W-Ni-TiO{sub 2} (PC) nano-composite coating was more compact, thicker and exhibited smaller grain size. The coated surface revealed different contents such as 43.4 and 65.4% of W in DC and PC coatings, respectively, which are considered to be a novel composition of the W-Ni alloy. XRD studies revealed that the NiW{sub 2} phase only occurs in the W-Ni-TiO{sub 2} (PC) nano-composite alloy. Electrical and thermal conductivities, microhardness and porosity values are enhanced by the addition of TiO{sub 2} to the alloy.

36 MATERIALS SCIENCE↗

Wear and Corrosion Behavior of Graphene-Nanoplate-Reinforced Copper Matrix Composites Prepared Through Electrostatic Self-Assembly

Synthesis of graphene nanoplates (GNPs)/copper (Cu) composites is one of the key challenges in the uniform dispersion of GNPs in the Cu matrix because of their density difference. In this work, GNPs/Cu composites are synthesized through electrostatic self-assembly and spark plasma sintering. The GNPs are uniformly dispersed in the Cu matrix. The graphene protective films are formed in the composites to protect the Cu matrix. The antifriction performance of the GNPs/Cu composites is investigated using a ball-on-disk apparatus. The corrosion resistance of the GNPs/Cu composites is estimated using potentiodynamic polarization curves. Wear and corrosion mechanisms are analyzed through scanning electron microscopy with energy-dispersive spectroscopy. The antifriction performance and corrosion resistance of the composites can be significantly improved by adding GNPs.

36 MATERIALS SCIENCE↗

Mechanical Characterization of High-Temperature Carbon Fiber-Polyphenylene Sulfide Composites for Large Area Extrusion Deposition Additive Manufacturing

Additive manufacturing (AM) is evolving from rapid prototyping to production of structural components. The widespread application of AM demands a high level of mechanical performance from these components, and it is therefore essential to improve feedstock material in order to meet these mechanical expectations. However, compared to traditional manufacturing techniques, the mechanical properties of AM materials and their resulting components are not well understood. In this study, we investigated the processability, microstructure, and mechanical performance of twin-screw compounded short carbon fiber reinforced polyphenylene sulfide (PPS) pellets as a feedstock material for big area AM (BAAM). The performance of the AM components was compared to that of traditional processing methods, namely injection molding (IM) and extrusion-compression molding (ECM). It was found that the AM composites exhibited 118% lower tensile strength and 55% lower tensile modulus when compared to traditional injection molding composite specimens; however, AM composites exhibited comparable properties to ECM composites. This response was attributed to highly aligned fibers in IM and AM samples. However, the AM composites contained porosity (15.5% volume), which reduced their mechanical properties in comparison to ECM composites. Finally, the IM process showed the maximum amount of fiber attrition with minimum porosity (0.007% volume), while the ECM process exhibited the least fiber attrition with 4.3% volume porosity.

36 MATERIALS SCIENCE↗

Densification and oxidation behavior of spark plasma sintered Hafnium Diboride-Hafnium Carbide composite

This study reports on the sintering and oxidation behaviors of Hafnium Diboride (HfB 2 ) and Hafnium Carbide (HfC) based ultra-high temperature ceramic (UHTC) composites. Pure Hafnium Diboride, Hafnium Carbide, and HfB 2 -50 vol% HfC composite were consolidated using spark plasma sintering (SPS) without the use of sintering aids. HfB 2 -HfC composite displayed a high sintered density of 98% as compared to 87% density of pure HfB 2 . The increased density of the HfB 2 -HfC composite is attributed to the bimodal powder distribution, which allowed for the smaller HfC particle to occupy the voids between the larger HfB 2 particles resulting in improved packing efficiency. Moreover, the higher planar surface energy, for the (111) and the (200) planes for HfC, contributed to the smaller HfC particle being a significant driving force in the sintering process. Oxidation studies of each material were carried out by exposing them to a high-speed plasma jet in a temperature exceeding 2700 °C. The results of these studies show an improved oxidation resistance of HfB 2 -HfC composite by 54% and 70% over pure HfC and HfB 2 , respectively. The enhanced oxidation behavior is attributed to B 2 O 3 filling in the porosity between the HfO 2 scale and protecting the underlying material. This study provides a new alternative to improve the sinterability of UHTC diborides by introducing another UHTC (i.e., HfC) to form a fully dense composite without sintering aid and superior oxidation resistance.

36 MATERIALS SCIENCE↗

Enhanced ductility in in-layer glass-carbon fiber/epoxy hybrid composites produced via tailored fiber placement

Experimental mechanical property results of composite materials with hybrid reinforcements (commingled glass and carbon fibers) are detailed and compared with single-fiber composite properties. In-layer hybrid materials, with carbon and glass fiber tows laid side-by-side, were produced via tailored fiber placement (TFP) technology. Detailed experiments showed a phenomenon of “enhanced ductility” of carbon fiber in the hybrid composites of 12–24% relative to an all-carbon fiber composite and multiple stress–strain peaks were observed. Here, this enhanced ductility was hypothesized to be due to the glass fibers mitigating the shock waves arising from the initial failures of carbon fibers, and preventing the premature failure of the remaining carbon fibers. A novel way to engineer the stress–strain behavior of a hybrid composite to achieve a metal-like ductile response (plateau of stress–strain behavior, often termed “elastic–plastic deformation”) was demonstrated by carefully selecting the type and composition of carbon and glass fiber materials.

36 MATERIALS SCIENCE↗

Economic competitiveness of pultruded fiber composites for wind turbine applications

Pultrusion manufacturing of fiber reinforced polymers has been shown to yield some of the highest mechanical properties for unidirectional composites, having a high degree of fiber alignment with consistent performance. Pultrusions offer a low-cost manufacturing approach for producing unidirectional composites with a constant cross-section and are used in many applications, including spar caps of wind turbine blades. However, as an intermediate processing step for wind blades, the additional cost of manufacturing pultrusions must be accompanied by sufficient increases in mechanical performance and system benefits. Wind turbine blades are manufactured using vacuum-assisted resin transfer molding with infused unidirectional fiberglass or carbon pultrusions for the spar cap. Infused fiberglass composites are among the most cost-effective structural materials available and replacing this material in the cost-driven wind industry has proven challenging, where infused fiberglass spar caps are still the predominant material system in use. To evaluate alternative material systems in a pultruded composite form, it is necessary to understand the costs for this additional manufacturing step which are shown to add 33%–55% on top of the material costs. A pultrusion cost model has been developed and used to quantify cost sensitivities to various processing parameters. The mechanical performance for pultruded composites is improved versus resin-infusion manufacturing with a 17% increase in design strength at a constant fiber volume fraction, but also enables higher achievable fiber volume fractions. The cost-specific mechanical performance is compared as a function of processing parameters for pultruded composites to identify the opportunities for alternative material and manufacturing approaches for wind turbine spar caps. Finally, four materials are compared in a representative wind turbine blade model to assess the performance of pultruded carbon fiber systems and pultruded fiberglass relative to infused fiberglass, where the pultruded systems produce lower weight blades with various cost distinctions.

42 ENGINEERING↗

Crashworthiness of recycled carbon fiber composite sinusoidal structures at dynamic rates

Fiber reinforced polymer composites are finding applications in the automotive space for structurally critical applications including crash management. The use of recycled carbon fiber reinforcement can greatly reduce carbon emissions. In this study, recycled carbon fiber composites were manufactured into a self-supporting geometry using three matrices: polyphenylene sulfide (PPS), acrylonitrile butadiene styrene (ABS), and a structural epoxy, and subsequently crushed between flat platens at dynamic rates ranging from 4.6 to 9.1 ms -1 at temperatures in a range of -40°C to 80°C. Load-displacement data was used to evaluate their specific energy absorption, crush efficiency, and steady-state crush stress. Further, the energy absorption of the ABS composites was strongly sensitive to temperature, while the PPS composites exhibited strong crush efficiency dependence with both rate and temperature. The epoxy composites exhibited stable crush behavior at dynamic crush rates but exhibited a dramatic reduction in crush efficiency relative to quasi-static tests. The results of this study indicate that recycled fiber composites can achieve very high energy absorption levels (50–80kJkg -1 at room temperature) that make them an excellent alternative to more expensive and less environmentally friendly continuous virgin fiber laminates.

42 ENGINEERING↗

Fluorescent detection of cholesterol using p-Sulfonatocalix[4]arene functionalized carbon nanotubes and thermally reduced graphite oxide composites

In the present study, carbon nanotube (CNT), thermally reduced graphite oxide (TRGO), and CNT-TRGO were functionalized with p-sulfonatocalix[4]arene (SC4) and then investigated for fluorescent detection of cholesterol in the presence of rhodamine 6G (R6G). All of the composite samples show effective quenching of R6G fluorescent intensity without cholesterol, but the fluorescence intensity significantly increases with the addition of cholesterol. The results indicate a strong interaction between SC4 composites and cholesterol rather than between the SC4 composites and R6G, increasing R6G fluorescence intensity in the presence of cholesterol due to the release of R6G from the SC4 composites. Formation of the complex, made of the SC4 composite plus the cholesterol, enables the detection of cholesterol in the wide range of cholesterol concentration up to 109 µM. The binding constant between SC4 and cholesterol has been calculated, indicating that the SC4 composites display the maximum binding constant of 1.9 × 10 4 M -1 with cholesterol.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Reassessing the proposed “CY chondrites”: Evidence for multiple meteorite types and parent bodies from Cr-Ti-H-C-N isotopes and bulk elemental compositions

Here, we report a coordinated bulk Cr-Ti-H-C-N isotopic and compositional study of six carbonaceous chondrites from Antarctica that are often considered to be related and termed Yamato-like carbonaceous (CY) chondrites. These meteorites are known to have undergone extensive aqueous alteration followed by different degrees of thermal alteration, to be similar to one another in regard to mineralogy, and share affinities with both the Ivuna-like carbonaceous (CI) and Mighei-like carbonaceous (CM) chondrites. While mineralogically similar, a key difference among these samples is that chondrules have been found in some of these samples, but not in others. The aim of this study is to evaluate the relationship of these meteorites to one another, and investigate how they relate to the CI and CM chondrite groups. We find that with the addition of the isotopic compositions of these ‘CY’ chondrites, there is now a continuum of isotopic compositions among the carbonaceous chondrites. The CI chondrites are no longer separate in O isotopic compositions from the other carbonaceous chondrite groups in plots of Cr-O and Ti-O. We also find that the ‘CY’ chondrites represent two distinct populations, which correlate with their heating stage. However, the peak temperatures experienced by each population can only explain the differences in H and C isotopes and abundances and N abundances between samples, and cannot have caused the differences in N, Cr, and Ti isotopes, or all the volatile element depletions of the sample’s bulk compositions. Instead, we conclude that the compositional and isotopic data of these two populations correlate with their known chondrule abundances, indicating distinct precursors for each population. We find it most likely that these samples originate from two distinct asteroids, implying that among the six samples studied here, there are not five related samples to constitute a new meteorite group. The chondrule-free heating Stage III samples are most likely heated CI chondrites, while the chondrule-bearing heating Stage IV samples could be heated CM chondrites.

58 GEOSCIENCES↗

Phosphate glass matrix composites incorporating trisilanol phenyl polyhedral oligomeric silsesquioxane prepared by viscous flow sintering method with enhanced benefits

The effect of mixing and sintering processes to prepare tin fluorophosphate glass (Pglass) matrix composites incorporating trisilanol phenyl polyhedral oligomeric silsesquioxane (TSP-POSS) was investigated by comparing manual and suspension mixing, one-step and stepwise sintering processes to explore the structure dynamics and physical properties in the composites as a function of the different process conditions used. Energy Dispersive X-ray analysis confirmed optimal homogeneous dispersion of the TSP-POSS molecules in the composites prepared by the suspension method. The observed increase of glass transition temperature and the reduction of non-bridging bonds in the composites are believed to be the reason for the effective dispersion of TSP-POSS molecules in the composites. The chemical reaction between the TSP-POSS and Pglass was strongly influenced by the mixing/dispersion and sintering processes investigated. 13 C cross polarized magic angle spinning (CP MAS) solid state nuclear magnetic resonance (NMR) spectroscopy confirmed the chemical stability of the TSP-POSS during the sintering process at elevated temperatures. In addition, a chemical reaction between the TSP-POSS and Pglass was evidenced by 29 Si CP MAS NMR analysis. Here, this study will provide a better fundamental understanding of the effective dispersion mechanism of the TSP-POSS molecules in the Pglass matrix that will facilitate tailoring the physicochemical properties of the composites with addition of various small concentrations of TSP-POSS for a number of applications where the pure Pglass is not applicable due to the intrinsic properties of the Pglass.

36 MATERIALS SCIENCE↗

Constructing magnetic polyaniline/metal hybrid nanostructures using polyaniline/Fe{sub 3}O{sub 4} composite hollow spheres as supports

Polyaniline (PANI)/Fe{sub 3}O{sub 4} composite hollow spheres have been successfully synthesized in one step using sulfonated polystyrene (PS) spheres as templates. The magnetic PANI hollow spheres were used as supports for noble metal nanoparticles (NPs) such as Au and Pd. The morphology, composition and magnetic properties of the resulting products were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, inductively coupled plasma (ICP) atomic spectra and vibrating sample magnetometer. The catalytic activity of magnetic PANI/Au composite shells on the oxidation of dopamine was investigated by cyclic voltammetry. The obtained results provide our product with a practical application for the detection of dopamine. On the other hand, the catalytic activity of magnetic PANI/Pd composite shells on the reduction of 4-nitroaniline was investigated by spectroscopic methods and compared with Pd/C catalyst which was already widely used in industrial production. - Graphical abstract: TEM image of PANI/Fe{sub 3}O{sub 4} hollow spheres which can be used as supports for a variety of catalysts such as noble metal nanoparticles. Based on the unique properties of polyaniline hollow spheres and Fe{sub 3}O{sub 4} NPs, we designed the synthesis of polyaniline/Fe{sub 3}O{sub 4} NPs composite hollow spheres as supports for catalysts such as noble metal NPs. As a result, the obtained composites exhibit enhanced catalytic activities and can be easily separated from reaction mixture by using an NdFeB permanent magnet.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Facile synthesis of Cu{sub 2}O nanocube/polycarbazole composites and their high visible-light photocatalytic properties

Cu{sub 2}O nanocube/polycarbazole composites have been prepared by an one-pot solvothermal process using carbazole as a reductant. The polycarbazole layer not only protected and stabilized Cu{sub 2}O particles, but also prohibited the recombination of photogenerated electrons-holes pair and facilitated interfacial charge transfer between polycarbazole and Cu{sub 2}O. The composition, structure and morphology of the obtained products was systematically studied by X-ray powder diffraction (XRD), Field-emission scanning electron microscopy (FE-SEM), High-resolution transmission electron microscopy (HRTEM), Fourier transformation infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS) and UV-visible spectrophotometer. Furthermore, the visible-light photocatalytic behavior of the Cu{sub 2}O nanocube/polycarbazole composites on the methyl orange was investigated. - Graphical abstract: The uniform and monodisperse Cu{sub 2}O nanocube/polycarbazole composites were prepared by an one-pot solvothermal process. As covered by polycarbazole, the photocatalytic activities of Cu{sub 2}O nanocubes were improved. The polycarbazole not only protected and stabilized Cu{sub 2}O cubes, but also prohibited the recombination of photogenerated electrons-holes pair and facilitated interfacial charge transfer between polycarbazole and Cu{sub 2}O. Highlights: > The Cu{sub 2}O/polycarbazole nanocube composite has a better photocatalytic activity. > We obtained the composite by an one-pot solvothermal process. > Carbazole monomers as reductants.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗