Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Battery”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Interfacial and Kinetic Origins of Voltage Loss in Neutral Zinc‐Air Batteries

Rechargeable zinc-air batteries are promising candidates for grid-scale energy storage; however, their practical deployment is limited by oxygen electrocatalysis inefficiencies and interfacial instabilities, particularly outside conventional alkaline electrolytes. Here, in this work, zinc-air batteries operating under neutral electrolyte conditions using ZnCl 2 soaked KC-PAA-PAM gel polymer electrolytes and electrochemically synthesized Ni/Fe layered double hydroxide electrocatalysts is investigated. Ni/Fe-LDH is intentionally employed as an OER-biased benchmark catalyst to diagnose electrolyte and interface driven limitations rather than as a bifunctional ORR/OER solution. Full cells exhibit highly stable cycling over hundreds of hours, yet operate at substantially suppressed charge and discharge voltages relative to the thermodynamic value. Electrochemical impedance analysis shows that ohmic losses contribute only minimally to this voltage suppression. Post-mortem X-ray photoelectron spectroscopy reveals metallic zinc accumulation on the air cathode and chloride-containing species on the anode, indicating parasitic interfacial processes. Synchrotron-based soft X-ray absorption spectroscopy confirms stable Ni 2+ and Fe 3+ oxidation states during cycling, consistent with OER-biased catalytic behavior, while neutral-electrolyte oxygen evolution measurements demonstrate strong electrolyte-induced suppression of oxygen kinetics. Together, these results show that electrolyte chemistry and cathode-side parasitic processes, rather than catalyst identity alone, dominate voltage losses in neutral zinc-air batteries, providing mechanistic insight into the fundamental challenges associated with neutral electrolyte operation.

Long duration energy storage↗
DOE OSTI2022

Tuning working potential of silicon-phosphorus anode via microstructure control for high-energy lithium-ion batteries

The primary research on anode materials of lithium-ion batteries have been focused on increasing the specific capacity, while the working potential that is also closely related to the practical energy density of batteries has been paid much less attention. In this paper, starting from micrometer-sized silicon and black phosphorus, we have reported a high-energy silicon-phosphorus/carbon anode (denoted as mSPC) via a high-energy ball milling process, which demonstrates an average discharge working potential of 0.3 volts versus lithium, together with a high reversible capacity of > 2000 mAh/g, high initial coulombic efficiency of 84%, excellent cycle stability, and superior rate capability up to 15 A/g. Furthermore, in situ focused-ion-beam scanning electron microscopy reveals that the volume change of the mSPC anode during repeated (de) lithiation is effectively alleviated. In contrast, starting from nanometer-sized silicon, the resulted anode (denoted as nSPC) not only presents a lower reversible capacity (~1200 mAh/g), but also exhibits a higher charge/discharge working potential, leading to reduced energy density. Our results indicate the importance of composition/structure control in tailoring the working potential and specific capacity of alloying-type anodes towards high-energy lithium-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2024

Finite Element Analysis and Machine Learning Guided Design of Carbon Fiber Organosheet-Based Battery Enclosures for Crashworthiness

Carbon fiber composite can be a potential candidate for replacing metal-based battery enclosures of current electric vehicles (E.V.s) owing to its better strength-to-weight ratio and corrosion resistance. However, the strength of carbon fiber-based structures depends on several parameters that should be carefully chosen. Here, in this work, we implemented high throughput finite element analysis (FEA) based thermoforming simulation to virtually manufacture the battery enclosure using different design and processing parameters. Subsequently, we performed virtual crash simulations to mimic a side pole crash to evaluate the crashworthiness of the battery enclosures. This high throughput crash simulation dataset was utilized to build predictive models to understand the crashworthiness of an unknown set. Our machine learning (ML) models showed excellent performance (R 2 > 0.97) in predicting the crashworthiness metrics, i.e., crush load efficiency, absorbed energy, intrusion, and maximum deceleration during a crash. We believe that this FEA-ML work framework will be helpful in down select process parameters for carbon fiber-based component design and can be transferrable to other manufacturing technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Customer trust in their utility company and interest in household-level battery storage

Here we seek to contribute to understanding household interest in battery storage, particularly the role of customer trust in their utility company. Using data from a survey of California households, we examine whether customers’ trust in their utility company is associated with their interest in battery storage. We find that customer trust that their utility company acts in their best interest is associated with lower levels of interest. Trust that the utility company is competent has some effect. Perceptions that battery storage has financial and environmental benefits and low nonmonetary costs are also associated with higher levels of interest.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

Hex-C 558 : A new porous metallic carbon allotrope for lithium-ion battery anode

Due to the limited specific capacity of graphite anodes in lithium-ion batteries (LIBs), it is imperative to find alternatives with better performance. Here in this work, we propose, for the first time, a three dimensional (3D) porous metallic 5-5-8 carbon monolith with hexagonal lattice as a potential candidate. With 5-5-8 carbon nanoribbon as the building block, this material, named Hex-C558, goes beyond graphene-nanoribbon-based 3D porous carbon structures. Using first-principles calculations, we show that Hex-C 558 is not only dynamically and thermally stable, but also is energetically more favorable than many other theoretically predicted carbon allotropes. More importantly, Hex-C 558 is metallic with ordered ionic conducting channels and possesses a low mass density of 1.05 gcm -3 , exhibiting great potential for ion-battery applications. As an anode for LIBs, Hex-C558 possesses a large specific capacity of 591 mAhg -1 , low diffusion energy barrier of 0.27 eV (at low Li concentration) and 0.52 eV (at high Li concentration), a low open-circuit voltage of 0.51 V, and a small volume change of 2.4%. This work provides a new route for the design and synthesis of novel carbon materials for battery applications by using pentagon-based building units.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Silver-carbon interlayers in anode-free solid-state lithium metal batteries: Current development, interfacial issues, and instability challenges

As an interlayer between the anode and the electrolyte of the all-solid-state lithium metal batteries (ASSLMBs), the silver-carbon (Ag-C) nanocomposite has been reported to significantly increase the energy density and cycle rate of solid-state lithium metal batteries. Ag-C interlayers serve as mixed ionic-electronic conductor that conducts both Li+ ions and electrons and lithium storage capacity. Unfortunately, it was unclear how the Ag-C interlayer regulated lithium plating and stripping. Moreover, the structural and chemical instabilities between the interlayer and the electrolyte, within the interlayer, or beneath the interlayer on lithium substrate are likely to cause cell failure. In this review, we discuss interfacial issues and summarize recent progress in solution strategies for ASSLMBs, with a specific focus on the use of a silver-carbon (Ag-C) nanocomposite interlayer in anode-free setups. Based on the Li transport kinetics among the Ag-C interlayers, the interfacial configurations of Ag-C interlayers are classified as either exterior or internal. Furthermore, the review concludes with a discussion of the perspectives and future prospects, allowing for the improvement of interlayer techniques for solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Highly efficient interface stabilization for ambient-temperature quasi-solid-state sodium metal batteries

Solid-state sodium (Na) batteries (SSSBs) using sulfide-based solid electrolytes (SSEs) hold tremendous promise due to their high theoretical specific capacity, enhanced safety and abundant resources. However, detrimental interfacial issues between SSEs and Na metal present a major challenge to the advancement of sulfide-based SSSBs. To address interfacial issues, we demonstrate an efficient approach by incorporating an ionic liquid electrolyte ((PYR/Na)TFSI) as interlayer to stabilize the Na metal/SSE interface. The presence of the (PYR/Na)TFSI interlayer enables the formation of a stable solid electrolyte interphase (SEI) to prevent the harmful reactions and inhibit Na dendrites. Combination of ab initio molecular dynamics simulations and X-ray photoelectron spectroscopy revealed that this stable SEI is largely composed of reduced products of TFSI -, such as NaF and CF 3 . As a result, the symmetric cells exhibited stable Na plating/striping cycling for 300 h at 0.1 mA cm -2 . In addition, FeS2||Na quasi-solid-state batteries delivered an impressive specific capacity of over 300 mAh g -1 under the current density of 20 mA g -1 at room temperature. Under a higher current density (100 mA g -1 ), such batteries performed with long-term cycling stability and maintained a specific capacity of around 103 mAh g -1 after 330 cycles. This work demonstrates the novel perspective of using an ionic liquid interlayer to address interfacial issues, contributing to the advancement of high-performance SSSBs for the next-generation energy storage systems.

25 ENERGY STORAGE↗
DOE OSTI2026

Covalent adaptable networks for electrolyte–binder integration in recyclable lithium metal batteries

Lithium-metal batteries (LMBs) are considered a promising next-generation energy storage technology due to their exceptionally high energy density. However, the development of solid polymer electrolytes and cathode binders for LMBs faces critical challenges, including interfacial instability, poor recyclability, and growing environmental concerns. In particular, current systems often rely on non-recyclable components featuring permanently crosslinked networks and polyfluoroalkyl substances (PFAS), such as poly(vinylidene fluoride) (PVDF), which cause battery waste and environmental harm. Herein, we introduce a multifunctional covalent adaptable network (CAN) platform based on thermally reversible Diels–Alder (DA) chemistry, designed for dual functionality as a CAN-based electrolyte (CAE) and a CAN-based cathode binder. The CAE achieves high ionic conductivity and strong storage modulus (1.4 mS cm −1 and ∼ 10 5 Pa at room temperature, respectively) and enables stable long-term cycling in symmetric Li||Li cells for over 2000 h with low overpotential. When it is applied as a cathode binder in LiFePO 4 (LFP) composite electrodes (C-LFP), the CAN matrix significantly reduces interfacial resistance and enhances discharge capacity compared to conventional PVDF-based systems. Thermal treatment induces self-healing at the cathode–electrolyte interface, further improving contact and yielding a discharge capacity of 150 mAh g −1 at 0.5 C. Moreover, the dynamic CAN architecture allows efficient recovery and reuse of lithium salts from spent electrolytes through retro-DA reactions under mild conditions (∼80 °C), establishing a low-energy, cost-effective recycling pathway. In conclusion, this work presents a scalable and sustainable strategy for high-performance LMBs by integrating recyclability, interfacial healing, and PFAS-free design, offering a holistic solution aligned with circular economy principles and next-generation battery demands.

Diels–Alder↗
DOE OSTI2021

2D Ni 0.25 Mn 0.75 O 2 : A high-performance cathode for multivalent ion batteries

Although Li-ion batteries have driven portable energy storage in recent decades, there is increasing concern about their safety, cost, and abundance of constituents. Multivalent ion batteries (MVIBs) have the potential to remedy these issues, but they are limited by the currently known MVIB cathodes, which fail to deliver unanimously favorable voltage, energy density, and diffusion kinetics. Here we used density functional theory (DFT) to model the performance of Li, Na, Mg, Ca, and Al ions when paired with 2D Ni 0.25 Mn 0.75 O 2 , a novel cathode that uses increased layer separation to improve on the kinetics of its 3D analog. Our calculations yielded maximum voltages of 3.38 V for Na and 2.7 V for Ca, outperforming 2D Na x MnO 2 and Na x NiO 2 . Diffusion barriers for Li, Na, and Ca are below 300 meV, comparable to existing battery technology and the endpoint 2D cathodes; meanwhile, Mg and Al have prohibitively high diffusion barriers, implying their incompatibility with this cathode. Lastly, density of states calculations and Bader charge analysis show that the cathode becomes conducting following ion adsorption, which is necessary for high-rate performance. 2D Ni 0.25 Mn 0.75 O 2 maintains performance seen with other 2D transition metal oxides while increasing cathode conductivity, indicating that it is a promising candidate for experimental investigation with Li, Na, and Ca ions.

25 ENERGY STORAGE↗
DOE OSTI2024

Dataset of mechanically induced thermal runaway measurement and severity level on Li-ion batteries

The deployment of Li-ion batteries covers a wide range of energy storage applications, from mobile phones, e-bikes, electric vehicles (EV) and stationary energy storage systems. However, safety issue such as thermal runaway is always one of the most important concerns to prevent Li-ion batteries from further market penetration. A standardized single-side indentation test protocol was developed to mechanically induce an internal short-circuit. The cell voltage, compressive load, indenter stroke, and temperature at the indentation point are measured in time series. The test data of each cell, along with cell parameters such as dimensions, mass, chemistry, state of charge (SOC), capacity, are integrated together to calculate a thermal runaway severity score from 0 to100. Complete data collection process including the original measured record, test method, severity score calculation scheme is presented in this article. The thermal runaway severity analysis and the more than 100 tested Li-ion battery records provide a good data source for further comparison and ranking of thermal runaway risks.

25 ENERGY STORAGE↗
DOE OSTI2019

Features of mechanical behavior of EV battery modules under high deformation rate

Here, we observe changes in material behavior of electric vehicle (EV) Li-ion battery cell modules when the loading speed increases from quasi-static to high speed (close to 1 m/s). A series of out-of-plane indentation experiments were performed on stacks of pouch cells placed in the specially designed enclosure to represent conditions in battery modules. Over one hundred of large format automotive pouch cells were tested under displacement rates differing by orders of magnitude. The details of internal failure were studied by X-ray tomography (XCT). We determine a shift in the force–displacement response from a parabolic behavior characteristic of particulate materials under compression to the response normal of fully dense materials with yield point. This shift is associated with dynamic effects in active materials which result in deep propagation of damage into the battery module, despite the fact that the internal short circuit is triggered when the displacement of the indenter is one half of that under the slow displacement rate.

25 ENERGY STORAGE↗
DOE OSTI2020

On electrolyte wetting through lithium-ion battery separators

The wettability by electrolyte is a critical characteristic of lithium-ion battery separators since electrolyte absorption is essential for ionic transport. Most importantly, fast absorption of electrolyte facilitates the electrolyte filling and wetting processes during the battery assembly. However, theoretical or experimental investigation of separator wettability has rarely been reported, and thus very little quantitative data can be found in the existing literature. Here, innovative experimental techniques and associated analytical models have been developed to fully characterize the electrolyte wetting behavior through battery separators. Both in-plane and through-plane imbibition processes are investigated. The results show that, electrolyte needs significantly longer time to wet separators than it does for commercial electrodes. The wetting rate depends significantly on the pore size, porosity, and micro-structure of the separators. Electrolyte in-plane wetting is only observed in the separators manufactured by the wet process. Increasing separator porosity and pore size is shown to be substantially increasing through-plane wetting rate. In addition, ceramic coating is shown to increase in-plane wetting but retard through-plane wetting.

25 ENERGY STORAGE↗
DOE OSTI2025

Optimal sizing of battery energy storage systems for peak shaving and demand response using a degradation-aware Bayesian Optimization-Mixed-Integer Linear Programming framework

The increasing integration of renewable energy and rising electricity demand highlight the importance of battery energy storage systems for peak shaving and demand response. Unlike prior approaches that overlook operational impacts on degradation, this study proposes a Bayesian Optimization–Mixed Integer Linear Programming framework for optimal battery energy storage system sizing. In this framework, Mixed Integer Linear Programming determines short-term scheduling while a calibrated electrochemical model iteratively evaluates degradation. The central hypothesis is that the framework can efficiently identify optimal sizes that yield realistic and economically robust outcomes. The method is tested across three scenarios: peak shaving, peak shaving with energy-reduction demand response, and peak shaving with power-reduction demand response. Results show that the framework converge to the optimum within 20 iterations out of 150 possible sizes. Under baseline conditions, the framework consistently selects the smallest feasible system, minimizing unnecessary degradation costs from oversized storage. Sensitivity analyses reveal that larger systems are favored as demand rates or incentives increase. Comparisons of demand response programs indicate that power-reduction demand response offers greater economic benefits than energy-reduction demand response, although demand savings from peak shaving remain the dominant contributor to overall performance. This study demonstrates that the proposed framework balances computational tractability with degradation fidelity, identifies critical economic thresholds for investment, and offers a practical, flexible tool to guide industrial stakeholders in cost-effective battery energy storage system deployment.

Batteries↗
DOE OSTI2019

Cathode electrolyte interface enabling stable Li–S batteries

A high-concentration, ether-based electrolyte with LiTFSI and LiNO 3 as the co-salts is proposed, which enables stable cycling of a lithium metal battery using sulfurized polyacrylonitrile (SPAN) as the cathode material. In addition to providing excellent protection for lithium metal anodes by forming the solid electrolyte interface (SEI), the electrolyte promotes the formation of a crystalline cathode electrolyte interface (CEI) on the SPAN surface composed of LiF and LiNO 2 . The CEI effectively prevents the formation of soluble polysulfide species and enables stable cycling of the Li-SPAN battery. The benefit of having effective CEI and SEI layers is also demonstrated in Li-SPAN cells with limited lithium supply, which exhibit lithium cycling efficiency values consistent with or exceeding Li/Cu test results, reaching 99.5%. In conclusion, the development of electrolyte chemistries to enable the formation of effective CEI layers is a promising approach to long-life lithium metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2019

Operando X-ray absorption spectroscopy applied to battery materials at ICGM: The challenging case of BiSb's sodiation

X-ray absorption spectroscopy (XAS) is a synchrotron-based, element-specific, short-range structural method largely used in the study of materials, already widely employed for the research of the electrochemical processes in battery systems. The high penetration of the X-rays makes XAS particularly suited for the study of battery materials under operando conditions using specifically developed in situ electrochemical cells. Here, the application of XAS to the study of battery materials carried out at Institut Charles Gerhardt Montpellier (France) will be outlined, illustrating the type of information provided by XAS. The challenging report of the sodiation of Bi 0.50 Sb 0.50 followed individually and simultaneously at both metals will be also presented in order to highlight the typical advantages of this technique even when it is pushed at its technical limits.

25 ENERGY STORAGE↗
DOE OSTI2019

Selective sodium-ion diffusion channels in Na 2 - x Fe 3 (PO 4 ) 3 positive electrode for Na-ion batteries

The electrochemical community around the world is focusing heavily on sodium-ion batteries R&D due to the huge abundance of sodium and need for large scale deployment of safe and inexpensive batteries for the electrical grid energy storage. Here, we observe the characterization of model parameters such as ionic diffusivity and interfacial kinetics, for a potential sodium-ion battery cathode material, Na 2 - x Fe 3 (PO 4 ) 3 , using experimental and computational investigations. The Na 2 - x Fe 3 (PO 4 ) 3 structure is characterized by two distinct one-dimensional (1-D) Na diffusion channels. Density Functional Theory (DFT) calculation reveals that Na is first fully removed from one of the channels followed by the subsequent removal of Na from the second channel. The experimental exploration reveals that, in the beginning of Na removal at 0 ≤ x ≤ 0.5; the sodium ion diffusivity is of the order of ~10 –11 cm 2 s –1 and then slightly decreases. This is further confirmed by comparing the calculated sodium diffusion barriers along the individual 1-D channels as well as between the channels. Nevertheless, the exchange current density slowly increases up to x=1.0 and remains quite constant thereafter. The magnitude of exchange current density is very low suggesting that the interfacial kinetics are the rate limiting factor. The obtained results indicate that Na 2 - x Fe 3 (PO 4 ) 3 could achieve better rate performance with long cycling stability through engineering of the particle morphology and microstructure.

25 ENERGY STORAGE↗
DOE OSTI2019

Garnet-rich composite solid electrolytes for dendrite-free, high-rate, solid-state lithium-metal batteries

Composite solid electrolytes (CSEs), which are composed of inorganic fillers and organic polymers, show improved safety and suppressed lithium dendrite growth in Li-metal batteries, as compared to flammable liquid electrolytes. However, the performance of current CSEs is limited by the agglomeration effect, with low content of inorganic Li + -conducting fillers and ineffective Li + transport between the inorganic fillers and the polymer matrix. To address these challenges, a new type of CSE composed of silane-modified Li 6.28 La 3 Al 0.24 Zr 2 O 12 (s@LLAZO) nanofibers and poly(ethylene glycol) diacrylate (PEGDA) is developed. Employment of the silane coupling agent, 3-(trimethoxysilyl)propyl methacrylate, enables the incorporation of a high content of LLAZO nanofibers (up to 70 wt%) with the polymer matrix and results in a well-percolated, three-dimensional LLAZO network fully embedded in the PEGDA matrix. Consequently, the silane coupling agent successfully eliminates the agglomeration effect, which ensures higher ionic conductivity, larger lithium transference number, wider electrochemical stability window, and better cycling stability for s@LLZAO-PEGDA CSEs. Excellent cycling stability and extraordinarily high rate capability (up to 10C) are demonstrated in the all-solid-state Li-metal batteries with LiFePO 4 and high-voltage Li[Ni 1/3 Mn 1/3 Co 1/3 ]O 2 cathodes at ambient temperature. This novel design of CSEs with s@LLAZO nanofibers paves the way for a new generation of improved functioning all-solid-state Li-metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Optimization of Oxygen Electrode Combined with Soluble Catalyst to Enhance the Performance of Lithium-Oxygen Battery

Lithium-air batteries possess a high theoretical energy density among the current battery technologies, and are expected to become the driving power for electric vehicles. However, the practical application of lithium air batteries is handicapped by their poor cycle life, high over-charge potential and low energy efficiency. Numerous studies have performed to improve the kinetics of the electrochemical reaction. Making a good oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) catalyst system is under intense scrutiny. In this work, we report a rational design of air electrode, which derives from biomass and presents a three-dimensional porous carbon architecture with high specific surface and large volume expansion coefficient. Combining with a soluble catalyst, this oxygen electrode presents an ultrahigh areal specific capacity of 7.95 mAh/cm 2 and a long cycling life up to 1000 cycles with suppressed polarization (about 0.46 V). Finally, the greatly improved overall performance is due to the synergetic effect of the novel designed oxygen electrode capable of mediating the redox mediators to trigger the ORR and OER process.

25 ENERGY STORAGE↗