Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AFTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,585 records · Page 88
All sourcesNASA NTRSDOE OSTI
NASA NTRS1947

Free-Spinning-Tunnel Tests of a 1/16-Scale Model of the Chance Vought XF5U-1 Airplane, TED No. NACA 2349

Spin tests of a 1/16-scale model of the Chance Vought XF5U-1 airplane have been performed in the Langley 20-foot free-spinning tunnel. The effect of control position and movement upon the erect and inverted spin and recovery characteristics ae well as the effects of propellers, of stability flaps, and of various revisions to the design configuration have been determined for the normal fighter loading. The investigation also included spin recovery parachute, tumbling, and pilot-escape tests. For the original design configuration, with or without windmilling propellers, the recovery characteristics of the model were considered unsatisfactory. Increasing the maximum upward deflection of the ailavators from 45 deg to 65 deg resulted in greatly improved recovery characteristics. Dimensional revisions to the original airplane configuration, which satisfactorily improved the general spin and recovery characteristics of the model, consisted of: (1) a supplementary vertical tail 34 inches by 59 inches (full-scale) attached to a boom 80 inches aft of the trailing edge of the airplane in the plane of symmetry, (2) a large semispan undersurface spoiler placed along the airplane quarter-chord line and opened on the outboard side in a spin, or (3) two additional vertical tails 64 inches by 52 inches (full-scale) located at the tips of the ailavators. A satisfactory parachute arrangement for emergency spin recovery from demonstration spins was found to be an arrangement consisting of a 13.3-foot parachute attached by a 30-foot towline to the arresting gear mast on the airplane and opened simultaneously with an 8-foot parachute on the outboard end of the wing attached by a 3-foot towline. Tests indicated that pilot escape from a spin would be extremely hazardous unless the pilot is mechanically ejected from the cockpit. Model tumbling tests indicated that the airplane would not tumble.

White, Richard P.↗
NASA NTRS1946

Flight Measurements of the Directional Stability and Control of a P-51D Airplane with a Horn-Balanced Rudder as Compared with Previously Tested Vertical-Tail Configurations

At the request of the Air Materiel Command, Army Air Forces, flight tests were conducted on a P-5lD-20-NA (AAF No. 44-63826) airplane equipped with a horn-balanced rudder. This rudder was fitted with an unbalancing tab as was the original product fan rudder. Tests were made both with the unbalancing tab in operation and with the unbalancing tab locked. The modification to the original vertical tail consisted of removing the cap from the top of the fin and adding 1.91 square feet of area to the rudder as the horn balance and 0.82 square foot of area to the top of the rudder aft of the hinge line. A comparison of the directional stability and control characteristics of the P-51D airplane with three different vertical-tail configurations - the horn balance, original production, and extended tail (with unbalancing tab locked) configurations are presented herein. The tests of the horn-balanced rudder were conducted at the Langley Laboratory in 1945. The tests of the original-tail configuration were previously conducted at the Ames Aeronautical Laboratory. Tests of the extended-tail configuration were conducted at the Langley Laboratory and are reported.

Mungall, Robert G.↗
NASA NTRS1955

Ditching Investigation of a 1/11-Scale Model of the Chance Vought F7U-3 Airplane, TED NO. NACA DE 360

An investigation was made of a 1/11-scale dynamically similar model of the Chance Vought F7U-3 airplane to study its behavior when ditched. The model was landed in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds, and configurations were investigated. The behavior of the model was determined from visual observations, acceleration records, and motion-picture records of the ditchings. Data are presented in tabular form, sequence photographs, time-history acceleration curves, and plots of attitude change against time after contact. From the results of the investigation, it was concluded that the airplane should be ditched at the lowest speed and highest attitude consistent with adequate control. The aft part of the fuselage and the main landing-gear doors will probably be damaged. In a calm-water ditching under these conditions the airplane will probably skip slightly and then porpoise for the remainder of the run. Maximum longitudinal decelerations will be about 3 1/2g and maximum normal accelerations will be about 7g in a landing run of about 500 feet.

Fisher, Lloyd J.↗
NASA NTRS1948

Tank Tests of a Powered Model of a Compression Plane, NACA Model 171A-2

The compression plane is intended for operation on or close to the surface of the water, and has a hull with a concave bottom which forms the upper surface of a tunnel into which air is forced under pressure to support part of the load. The results of the tests made in Langley tank no. 1 include values of the horizontal forces, trimming moment, and static pressure in the tunnel for a wide range of loads and speeds and two power conditions, and are presented in the form of curves against speed with load as a parameter. The results are scaled up to 10 times the model size for three conditions at which the model is self-propelled at a steady speed. Lift is obtained from the static pressure of air in the tunnel. In general, the ratio of the gross load to the total resistance increases with increase in load and decrease in speed. This ratio varies between l-7 and 5.7 at high speeds and has a maximum value of 7. The total resistance is nearly the same for both power conditions except at low speeds and heavy loads. No abrupt change in forces on the hull or flow around the hull occurs in. the region of zero draft. The centers of pressure are generally far aft. At the most efficient trim (1.2'), considerable bow-up moment would be required for practicable operation. There is no abrupt transition from the air-borne to the water- borne condition.

Mottard, Elmo J.↗
NASA NTRS1948

An Investigation of the Aerodynamic Characteristics of a 3/4-Scale Model of the EX-3 Pine-Cone-Head Pellet in the Langley High-Speed 7-by 10-Foot Wind Tunnel

An investigation of the Ex-3 pine-cone-head pellet was made in the Langley high-speed 7-by 10-foot wind tunnel to determine the static force and moment characteristics at high Mach numbers with the reference center of gravity located at 37.5 percent of the over-all length aft of the nose. For this center-of-gravity location there were no secondary trim positions, and the center-of-pressure position was not appreciably affected by Mach number.

Campbell, George S.↗
NASA NTRS1947

Hydrodynamic Qualities of a 1/10-Size Powered Dynamic Model of the XP5Y-1 Flying Boat in Smooth Water: Langley Tank Model 246, TED No. NACA DE 320

The hydrodynamic characteristics of a 1/10-size powered dynamic model of the XP5Y-1 flying boat were determined in Langley tank no. 1. Stable take-offs were possible at all practicable positions of the center of gravity and flap deflections. An increase in gross load from 123.5 to 150.0 pounds (21.5 percent) had only a slight effect on the stable range for take-off. A decrease in forward acceleration from 3.0 to 1.0 feet per second per second had only a very small effect on the stable range for take-off. In general, the landings were free from skipping except at trims below 6 deg where one skip was encountered at an aft position of the center of gravity. The model porpoised during the landing runout at all positions of the center of gravity when landed at trims above 10 deg. Spray in the propellers was light at the design gross load, and was not considered excessive,at a gross load of 136.0 pounds.

Woodward, David R.↗
NASA NTRS2005

Nozzle Aerodynamic Stability During a Throat Shift

An experimental investigation was conducted on the internal aerodynamic stability of a family of two-dimensional (2-D) High Speed Civil Transport (HSCT) nozzle concepts. These nozzles function during takeoff as mixer-ejectors to meet acoustic requirements, and then convert to conventional high-performance convergent-divergent (CD) nozzles at cruise. The transition between takeoff mode and cruise mode results in the aerodynamic throat and the minimum cross-sectional area that controls the engine backpressure shifting location within the nozzle. The stability and steadiness of the nozzle aerodynamics during this so called throat shift process can directly affect the engine aerodynamic stability, and the mechanical design of the nozzle. The objective of the study was to determine if pressure spikes or other perturbations occurred during the throat shift process and, if so, identify the caused mechanisms for the perturbations. The two nozzle concepts modeled in the test program were the fixed chute (FC) and downstream mixer (DSM). These 2-D nozzles differ principally in that the FC has a large over-area between the forward throat and aft throat locations, while the DSM has an over-area of only about 10 percent. The conclusions were that engine mass flow and backpressure can be held constant simultaneously during nozzle throat shifts on this class of nozzles, and mode shifts can be accomplished at a constant mass flow and engine backpressure without upstream pressure perturbations.

Kawecki, Edwin J.↗
NASA NTRS2003

Simulating a Tailless Re-Entry Vehicle

Virtual Flight - RITE (Rapid Integration Test Environment) is a NASA program devoted to the development of rapid prototyping technology for the design of aerospace vehicles. In the fourth simulation entry in this series of projects, a Crew Transfer Vehicle concept design developed at NASA-Ames Research Center was simulated. This concept vehicle, known as CTV8, is a delta-wing design with sharp leading edges to improve the hypersonic lift-to-drag ratio (L/D). Control surfaces included ailerons and elevators on the trailing edge of the wing, a rudder on the trailing edge of the vertical tail, and upper and lower body flaps (on the aft upper and lower edges of the fuselage) for speed control.

Bunell, John W.↗
NASA NTRS2005

The Influence of Projectile Trajectory Angle on the Simulated Impact Response of a Shuttle Leading Edge Wing Panel

In support of recommendations by the Columbia Accident Investigation Board, a team has been studying the effect of debris impacting the reinforced carbon-carbon panels of the shuttle leading edge. The objective of this study was to examine the effect of varying parameters of the debris trajectory on the damage tolerance. Impacts at the upper and lower surface and the apex of the leading edge were examined. For each location, trajectory variances included both the alpha and beta directions. The results of the analysis indicated in all cases the beta sweep decreased the amount of damage to the panel. The increases in alpha resulted in a significant increase in damage to the RCC panel. In particular, for the lower surface, where the alpha can increase by 10 degrees, there was a nearly 40% increase in the impulse. As a result, it is recommended that for future analyses, a 10 degree offset in alpha from the nominal trajectory is included for impacts on the lower surface. It is also recommended to assume a straight aft, or zero beta, trajectory for a more conservative analysis.

Spellman, Regina L.↗
NASA NTRS1997

Stator Indexing in Multistage Compressors

The relative circumferential location of stator rows (stator indexing) is an aspect of multistage compressor design that has not yet been explored for its potential impact on compressor aerodynamic performance. Although the inlet stages of multistage compressors usually have differing stator blade counts, the aft stages of core compressors can often have stage blocks with equal stator blade counts in successive stages. The potential impact of stator indexing is likely greatest in these stages. To assess the performance impact of stator indexing, researchers at the NASA Lewis Research Center used the 4 ft diameter, four-stage NASA Low Speed Axial Compressor for detailed experiments. This compressor has geometrically identical stages that can circumferentially index stator rows relative to each other in a controlled manner; thus it is an ideal test rig for such investigations.

Barankiewicz, Wendy S.↗
NASA NTRS2005

Characterization of Unsteady Flow Structures Around Tandem Cylinders for Component Interaction Studies in Airframe Noise

A joint computational and experimental study has been performed at NASA Langley Research Center to investigate the unsteady flow generated by the components of an aircraft landing gear system. Because the flow field surrounding a full landing gear is so complex, the study was conducted on a simplified geometry consisting of two cylinders in tandem arrangement to isolate and characterize the pertinent flow phenomena. This paper focuses on the experimental effort where surface pressures, 2-D Particle Image Velocimetry, and hot-wire anemometry were used to document the flow interaction around the two cylinders at a Reynolds Number of 1.66 x 10(exp 5), based on cylinder diameter, and cylinder spacing-todiameter ratios, L/D, of 1.435 and 3.70. Transition strips were applied to the forward cylinder to produce a turbulent boundary layer upstream of the flow separation. For these flow conditions and L/D ratios, surface pressures on both the forward and rear cylinders show the effects of L/D on flow symmetry, base pressure, and the location of flow separation and attachment. Mean velocities and instantaneous vorticity obtained from the PIV data are used to examine the flow structure between and aft of the cylinders. Shedding frequencies and spectra obtained using hot-wire anemometry are presented. These results are compared with unsteady, Reynolds-Averaged Navier-Stokes (URANS) computations for the same configuration in a companion paper by Khorrami, Choudhari, Jenkins, and McGinley (2005). The experimental dataset produced in this study provides information to better understand the mechanisms associated with component interaction noise, develop and validate time-accurate computer methods used to calculate the unsteady flow field, and assist in modeling of the radiated noise from landing gears.

Jenkins, Luther N.↗
NASA NTRS2005

High and Dry: Trading Water Vapor, Fuel and Observing Time for SOFIA

The Stratospheric Observatory for Infrared Astronomy (SOFIA) is NASA's next generation airborne astronomical observatory. The facility consists of a 747-SP modified to accommodate a 2.5 meter telescope. SOFIA is expected to fly an average of 140 science flights per year over it's 20 year lifetime, and will commence operations in early 2005. The SOFIA telescope is mounted aft of the wings on the port side of the aircraft and is articulated through a range of 20 deg to 60 deg of elevation. A significant problem in future SOFIA operations is that of scheduling Facility Instrument (E) flights in support of the SOFIA General Investigator (GI) program. GIs are expected to propose small numbers of observations, and many observations must be grouped together to make up single flights. Approximately 70 GI flight per year are expected, with 5-15 observations per flight.

Frank, Jeremy↗
NASA NTRS2005

Modular Engine Noise Component Prediction System (MCP) Technical Description and Assessment Document

This report describes an empirical prediction procedure for turbofan engine noise. The procedure generates predicted noise levels for several noise components, including inlet- and aft-radiated fan noise, and jet-mixing noise. This report discusses the noise source mechanisms, the development of the prediction procedures, and the assessment of the accuracy of these predictions. Finally, some recommendations for future work are presented.

Herkes, William H.↗
NASA NTRS1999

Teflon FEP Analyzed After Retrieval From the Hubble Space Telescope

During the Hubble Space Telescope (HST) Second Servicing Mission, 6.8 years after the telescope was deployed in low Earth orbit, degradation of unsupported Teflon FEP (DuPont; fluorinated ethylene propylene), used as the outer layer of the multilayer insulation (MLI) blankets, was evident as large cracks on the telescope light shield. A sample of the degraded outer layer (see the photograph) was retrieved during the second servicing mission and returned to Earth for ground testing and evaluation. Also retrieved was a Teflon FEP radiator surface from a cryogen vent cover that was exposed to the space environment on the aft bulkhead of the HST. NASA Goddard Space Flight Center directed the efforts of the Hubble Space Telescope MLI Failure Review Board, whose goals included determining the FEP degradation mechanisms. As part of the investigations into the degradation mechanisms, specimens retrieved from the first and second HST servicing missions, 3.6 and 6.8 years after launch, respectively, were characterized through exhaustive mechanical, optical, and chemical testing. Testing led by Goddard included scanning electron microscopy, optical microscopy, tensile testing, solar absorptance measurements, time-of-flight secondary ion mass spectroscopy (TOF-SIMS), Fourier transform infrared microscopy (m-FTIR), attenuated total reflectance infrared microscopy (ATR/FTIR), and x-ray diffraction (XRD). The NASA Lewis Research Center contributed significantly to the analysis of the retrieved HST materials by leading efforts and providing results of bend testing, surface microhardness measurements, x-ray photoelectron spectroscopy, solid-state nuclear magnetic resonance spectroscopy, and density measurements. Other testing was conducted by Nano Instruments, Inc., and the University of Akron.

Dever, Joyce A.↗
NASA NTRS2005

Effect of Impact Location on the Response of Shuttle Wing Leading Edge Panel 9

The objective of this paper is to compare the results of several simulations performed to determine the worst-case location for a foam impact on the Space Shuttle wing leading edge. The simulations were performed using the commercial non-linear transient dynamic finite element code, LS-DYNA. These simulations represent the first in a series of parametric studies performed to support the selection of the worst-case impact scenario. Panel 9 was selected for this study to enable comparisons with previous simulations performed during the Columbia Accident Investigation. The projectile for this study is a 5.5-in cube of typical external tank foam weighing 0.23 lb. Seven locations spanning the panel surface were impacted with the foam cube. For each of these cases, the foam was traveling at 1000 ft/s directly aft, along the orbiter X-axis. Results compared from the parametric studies included strains, contact forces, and material energies for various simulations. The results show that the worst case impact location was on the top surface, near the apex.

Lyle, Karen H.↗
NASA NTRS2005

Trial by Fire

The NASa/ATK Thiokol space shuttle solid rocket motor program has doubled ground test firings and enhanced manufacturing quality and process control to increase safety for Discovery's return to flight. There are a number of places where we've strengthened our engineering and our processes, says Mike Kahn, ATK Thiokol vice president of space launch systems. Protecting the booster against corrosion in the humid Florida environment is one area that has been addressed. Since the loss of Columbia, ATK Thiokol and the Marshall Space Flight Center have completely reevaluated the shuttle solid rocket motor's design certification and found no major problems, Kahn said. The Thiokol solid motors did not play a role in the 2003 Columbia accident, but the motor's older field joint design (since replaced) was the primary cause of the 1986 Challenger accident that killed seven astronauts. The 129 X 12-ft. ATK Thiokol reusable solid rocket motor forms the core of the shuttle's two solid rocket boosters (SRBs). United Space Alliance (USA) has overall responsibility for the booster's nose-mounted systems such as recovery parachutes and aft-mounted thrust vector control systems that increase the length to 149 ft. USA and its subcontractors have also reaffirmed quality control on systems such as the booster's Hamilton Sundstrand hydraulic power units for critical thrust vector control. And to ensure greater safeguards against booster debris jeopardizing the orbiter, a bolt-catcher system to restrain the large bolts, severed at booster separation, was also redesigned.

Covault, Craig↗
NASA NTRS2004

Turbofan Engine Simulated in a Graphical Simulation Environment

Recently, there has been an increase in the development of intelligent engine technology with advanced active component control. The computer engine models used in these control studies are component-level models (CLM), models that link individual component models of state space and nonlinear algebraic equations, written in a computer language such as Fortran. The difficulty faced in performing control studies on Fortran-based models is that Fortran is not supported with control design and analysis tools, so there is no means for implementing real-time control. It is desirable to have a simulation environment that is straightforward, has modular graphical components, and allows easy access to health, control, and engine parameters through a graphical user interface. Such a tool should also provide the ability to convert a control design into real-time code, helping to make it an extremely powerful tool in control and diagnostic system development. Simulation time management is shown: Mach number versus time, power level angle versus time, altitude versus time, ambient temperature change versus time, afterburner fuel flow versus time, controller and actuator dynamics, collect initial conditions, CAD output, and component-level model: CLM sensor, CAD input, and model output. The Controls and Dynamics Technologies Branch at the NASA Glenn Research Center has developed and demonstrated a flexible, generic turbofan engine simulation platform that can meet these objectives, known as the Modular Aero-Propulsion System Simulation (MAPSS). MAPSS is a Simulink-based implementation of a Fortran-based, modern high pressure ratio, dual-spool, low-bypass, military-type variable-cycle engine with a digital controller. Simulink (The Mathworks, Natick, MA) is a computer-aided control design and simulation package allows the graphical representation of dynamic systems in a block diagram form. MAPSS is a nonlinear, non-real-time system composed of controller and actuator dynamics (CAD) and component-level model (CLM) modules. The controller in the CAD module emulates the functionality of a digital controller, which has a typical update rate of 50 Hz. The CLM module simulates the dynamics of the engine components and uses an update rate of 2500 Hz, which is needed to iterate to balance mass and energy among system components. The actuators in the CAD module use the same sampling rate as those in the CLM. Two graphs of normalized spool speed versus time in seconds and one graph of normalized average metal temperature versus time in seconds is shown. MAPSS was validated via open-loop and closed-loop comparisons with the Fortran simulation. The preceding plots show the normalized results of a closed-loop comparison looking at three states of the model: low-pressure spool speed, high-pressure spool speed, and the average metal temperature measured from the combustor to the high-pressure turbine. In steady state, the error between the simulations is less than 1 percent. During a transient, the difference between the simulations is due to a correction in MAPSS that prevents the gas flow in the bypass duct inlet from flowing forward instead of toward the aft end, which occurs in the Fortran simulation. A comparison between MAPSS and the Fortran model of the bypass duct inlet flow for power lever angles greater than 35 degrees is shown.

Parker, Khary I.↗
NASA NTRS2005

STS-114 Flight Day 3 Highlights

Video coverage of Day 3 includes highlights of STS-114 during the approach and docking of Discovery with the International Space Station (ISS). The Return to Flight continues with space shuttle crew members (Commander Eileen Collins, Pilot James Kelly, Mission Specialists Soichi Noguchi, Stephen Robinson, Andrew Thomas, Wendy Lawrence, and Charles Camarda) seen in onboard activities on the fore and aft portions of the flight deck during the orbiter's approach. Camarda sends a greeting to his family, and Collins maneuvers Discovery as the ISS appears steadily closer in sequential still video from the centerline camera of the Orbiter Docking System. The approach includes video of Discovery from the ISS during the orbiter's Rendezvous Pitch Maneuver, giving the ISS a clear view of the thermal protection systems underneath the orbiter. Discovery docks with the Destiny Laboratory of the ISS, and the shuttle crew greets the Expedition 11 crew (Commander Sergei Krikalev and NASA ISS Science Officer and Flight Engineer John Phillips) of the ISS onboard the station. Finally, the Space Station Remote Manipulator System hands the Orbiter Boom Sensor System to its counterpart, the Shuttle Remote Manipulator System.

Source record↗