Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “threshold”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Impact of reservoir parameters and wellbore permeability uncertainties on CO 2 and brine leakage potential at the Shenhua CO 2 Storage Site, China

Here, this paper describes a system-level risk assessment for the Shenhua CO 2 storage site, China, using the National Risk Assessment Partnership Integrated Assessment Model for Carbon Storage (NRAP-IAM-CS). Here, we begin by determining the optimal number of Monte Carlo (MC) simulations to achieve CO 2 and brine leakage result convergence. Then, we calculate mass CO 2 and brine leakage to the atmosphere and a hypothetical shallow aquifer. Finally, we assess the geochemical impacts in the event of leakage as if there were a shallow freshwater aquifer at the Shenhua site. Simulation results show that leakage results tend to stabilize after 300 Monte Carlo simulations. When the three wells on site are assigned a permeability of 10 -11 m 2 (representing significantly leaking wells), moderate CO 2 and brine leakages occur, and the percentage of CO 2 leakage exceeds the threshold value we set based on the Intergovernmental Panel on Climate Change (IPCC). This is, however, unlikely to be the case for the Shenhua site. For all the other scenarios, the CO 2 leakage is trivial although there is still the possibility of CO 2 leakage into the groundwater aquifer exceeding the 1% threshold over 1000 years, assuming constant legacy wellbore permeability. For the significantly leaking scenario, there is a 10% probability to have a moderate (2.7 × 10 7 m 3 ) leakage-affected volume in the shallow aquifer with the pH below 6.5, and a large (1.4 × 10 8 m 3 ) volume with the total dissolved solids (TDS) above 500 ppm, hence pH and TDS may be considered for site monitoring plans. Based on the simulation results, there is a very low probability of significant CO 2 /brine leakage through the existing wells at the Shenhua CO 2 storage site.

58 GEOSCIENCES↗
DOE OSTI2022

Generalized Analysis of Dynamic Flow Fouling on Heat Transfer Surfaces

Several energy applications involve flow of untreated heat transfer fluids that contain trace amounts of mineral salts, such as calcium carbonate and calcium sulfate, which show reverse solubility with temperature. The gradual accretion of these salts onto the heat transfer surfaces causes fouling that degrades thermal performance over time. While fouling of bare surfaces has been extensively studied, fouling of nonwetting superhydrophobic or liquid-infused surfaces is less understood, especially under dynamic flow conditions. This study presents a systematic experimental analysis to elucidate dynamic flow fouling of calcium carbonate and calcium sulfate on smooth, superhydrophobic and liquid-infused surfaces in a generalized manner. Here, copper tubes with modified inner surface wettability are fabricated and subjected to forced convection at different flow rates and fouling salt concentrations. Fouling characteristics of the two salts on the different surfaces are examined through microstructural analysis, and quantified in terms of asymptotic fouling resistance that measures the total extent of fouling, and a threshold time, which correlates to the onset of significant fouling. Using Taguchi design of experiments, the study reports, for the first time, closed-form analytical relationships for the asymptotic fouling thermal resistance and threshold time on the Reynolds number, dimensionless concentration of fouling agent and dimensionless infused liquid viscosity that represents the different surface types in a unified manner. It is shown that the analytical model accurately predicts the fouling characteristics in up to about 97% of the data, based on which contour maps of optimum surface designs for minimizing fouling resistance are presented. The results provide information on designing surfaces for reduced fouling or for estimating the fouling characteristics for a given surface in applications.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Spectroscopy and dynamics of the v = 1 levels derived from the OH(D) stretching modes in the I‾∙HDO complex using CW and time-resolved, resonant two-photon infrared excitation of the cryogenically cooled ions

The vibrational energy levels of the two isotopomers adopted by the I‾∙HDO ion-molecule complex occur such that the OH(D) stretching fundamentals span its dissociation energy, thus enabling a spectroscopic investigation of the dynamics displayed by a system prepared in the vicinity of the dissociation threshold. This regime is explored using infrared photoexcitation of the mass-selected complexes cooled in a cryogenic radiofrequency (Paul) ion trap. Survey spectra are obtained at modest resolution using two-color, IR-IR photodissociation with nanosecond lasers to establish the level structure and unimolecular decay dynamics of the v = 1 and 2 levels of the bound OH(D) oscillator. The v = 1 levels are prepared by fixed frequency excitation in the trap and the absorption spectra arising from this excited state are probed by photofragmentation of the complex with a second pulsed IR laser after a variable delay time (0 to 20 ms). The transitions to levels above the dissociation threshold for I‾ + HDO formation are observed to be sharp (~5 cm -1 FWHM). At low pressure, the bound OD (v = 1) population relaxes very slowly (~3 ms), consistent with resonant fluorescence in the IR. The collisional quenching rate constants of this level by the He buffer gas were estimated to be on the order 3 x 10 -12 cm 3 /s based on a crude Stern-Volmer analysis. Here, the rotational fine structure and linewidths (≲0.01 cm -1 FWHM) arising from transitions of the non-bonded OH stretch fundamental of the OD-bound isotopomer that lies just above the dissociation energy are determined using single photon photodissociation by excitation of the 10 K ions with a single-frequency, CW IR laser in the ion trap.

Cryogenic ion infrared spectroscopy↗
DOE OSTI2021

Translating nanoparticle dosimetry from conventional in vitro systems to occupational inhalation exposures

As encouraged by Toxicity Testing in the 21st Century, researchers increasingly apply high-throughput in vitro approaches to identify and characterize nanoparticle hazards, including conventional aqueous cell culture systems to assess respiratory hazards. Translating nanoparticle dose from conventional toxicity testing systems to relevant human exposures remains a major challenge for assessing occupational risk of nanoparticle exposures. Here, we explored existing computational tools and data available to translate nanoparticle dose metrics from cellular test systems to inhalation exposures of silver nanoparticles in humans. We used the Multiple-Path Particle Dosimetry (MPPD) Model to predict deposition of humans exposed to 20 and 110 nm silver nanoparticles at 0.9 µg/m3 over an 8 hr period, the proposed a National Institute of Occupational Safety and Health (NIOSH) recommended exposure limit (REL). MPPD predicts 1.88 and 0.98 µg of silver deposited in an 8 hr period for 20 and 110 nm nanoparticles, respectively, with 20 nm particles displaying nearly 11-fold higher total surface area deposited. Peak nanoparticle concentrations occurred more proximal in the pulmonary tract compared to mass deposition patterns (generation 5 vs. generations 20-21, respectively) due to regional differences in lung lining fluid volumes. Assuming 0.4% nanoparticle dissolution by mass as previously measured, we predict peak concentrations of silver ions in cells of 0.24 and 0.17 µg/mL for 20 and 110 nm particles, respectively. Both predicted concentrations are below the measured toxic threshold of 1.7 µg/mL of silver ions in cells from in vitro assessments. Assuming 4% dissolution by mass, we predict 10-fold higher silver concentrations in tissues, peaking at 2.4 and 1.7 µg/mL, for 20 and 110 nm nanoparticles respectively, exceeding the observed in vitro toxic threshold and highlighting the importance and sensitivity of dissolution rates. Overall, this approach offers a framework for extrapolating nanotoxicity results from in vitro cell culture systems to human exposures. Aligning appropriate dose metrics from in vitro and in vivo hazard characterizations and human pulmonary doses from occupational exposures are critical components for successful nanoparticle risk assessment and worker protection and provide guidance for designing future in vitro studies aimed at relevant human exposures.

Smith, Jordan N.↗
DOE OSTI2020

SubTSBR to tackle high noise and outliers for data-driven discovery of differential equations

Data-driven discovery of differential equations has been an emerging research topic. We propose a novel algorithm subsampling-based threshold sparse Bayesian regression (SubTSBR) to tackle high noise and outliers. The subsampling technique is used for improving the accuracy of the Bayesian learning algorithm. It has two parameters: subsampling size and the number of subsamples. When the subsampling size increases with fixed total sample size, the accuracy of our algorithm goes up and then down. When the number of subsamples increases, the accuracy of our algorithm keeps going up. We demonstrate how to use our algorithm step by step and compare our algorithm with threshold sparse Bayesian regression (TSBR) for the discovery of differential equations. We show that our algorithm produces better results. We also discuss the merits of discovering differential equations from data and demonstrate how to discover models with random initial and boundary condition as well as models with bifurcations. The numerical examples are: (1) predator-prey model with noise, (2) shallow water equations with outliers, (3) heat diffusion with random initial and boundary condition, and (4) fish-harvesting problem with bifurcations.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Climate-extreme modeling framework for sustainable flood management in the Arabian Peninsula

Evaluating extreme precipitation events (EPEs) is essential for building climate-resilient water management strategies, but it remains a major challenge in ungauged basins. Using the 26,070 km 2 Wadi al-Rummah basin in central Saudi Arabia as a case study, we developed an alternative, reliable, cost-effective satellite-based framework that combines empirically derived EPE thresholds, imagery-calibrated 2D hydrodynamic modeling, GRACE water-storage diagnostics, and bias-corrected CMIP6 projections to assess flood hazards and recharge potential under current and future climate scenarios in ungauged basins. The integrated approach and the resulting findings followed four key steps: (1) Identified a 22.5 mm EPE threshold, the 80th percentile of 3-day GPM/IMERG rainfall (2000–2024), aligned with flood-triggering events (Nov 2018: 23–28 mm; Apr, 2023: 42 mm); (2) Developed and calibrated a RiverFlow2D model using Sentinel-2 and PlanetScope imagery for the November 2018 flood, accurately reproducing flood depth and extent (RMSE ≤0.31 m; fuzzy-Dice ≥0.91), and estimating runoff (41 %), infiltration (25 %), and evaporation (34 %); (3) Independently validated the model with the April 2023 event (RMSE ≤0.35 m; fuzzy-Dice ≥0.86); (4) Conducted climate projections (2025–2100) from five bias-corrected NEX-GDDP CMIP6 models that revealed a 34 % increase in EPE intensity under SSP2-4.5 and 48 % under SSP5-8.5 scenarios, relative to 20th-century baselines. Our findings indicate that while intensifying extremes in the 21st century increase flood risk, the results highlight the potential for episodic recharge if effective retention strategies are employed, and offer a transferable model for climate-informed planning in data-scarce arid regions.

CMIP6↗
DOE OSTI2026

Creating high-precision reference gas standards of 85Kr for groundwater age-dating

Absolute gas counting (AGC) was applied to two gas blends of 85Kr in argon-methane (P10) counting gas to establish a high-precision specific activity (Bq/cm3) reference value for characterizing 85Kr detection efficiency for groundwater age dating measurements. The AGC or length-compensated technique has been utilized by the metrology community for decades and is an accepted method for developing radioactive gas standards. The AGC capability at Pacific Northwest National Laboratory (PNNL) uses a set of nine unequal-length proportional counters with precisely-measured internal volumes, and a gas loading system with high-precision pressure and temperature sensors. A series of AGC measurements were collected at multiple pressures to determine the inverse pressure relationship (1/P) for 85Kr and define a wall-effect correction that accounts for events decaying into the detector wall and not depositing sufficient energy in the gas to be detected. In addition to the wall-effect, two additional corrections were evaluated and are discussed in detail. Specifically, the threshold effect which accounts for events deposited below the analysis threshold and a detection efficiency as a function of detector volume effect that was observed during analysis. A robust uncertainty model was developed using the Guide to the expression of Uncertainty in Measurements (GUM) approach. The combination of carefully scrutinized correction factors, precise measurements of pressure, temperature and detector volume, and robust counting statistics resulted in the determination of high-precision specific activity values with 0.50% or less total combined uncertainty for two Kr-in-P10 reference gas standards (KP10) that will enable new groundwater age-dating measurements at PNNL.

Kr-85↗
DOE OSTI2020

Configurational stability of a crack propagating in a material with mode-dependent fracture energy – Part II: Drift of fracture facets in mixed-mode I+II+III

In earlier papers (Leblond et al., 2011; 2019), we presented linear stability analyses of the coplanar propagation of a crack loaded in mixed-mode I+III, based on a “double” propagation criterion combining (Griffith, 1920)’s energetic condition and (Goldstein and Salganik, 1974)’s principle of local symmetry. The difference between the two papers was that in the more recent one, the local value of the critical energy-release-rate was no longer considered as a constant, but heuristically allowed to depend upon the ratio of the local mode III to mode I stress intensity factors. This led to a much improved, qualitatively acceptable agreement of theory and experiments, for the “threshold” value of the ratio of the unperturbed mode III to mode I stress intensity factors, above which coplanar propagation becomes unstable. In this paper, the analysis is extended to the case where a small additional mode II loading component is present in the initially planar configuration of the crack, generating a small, general kink of this crack from the moment it is applied. The main new effect resulting from presence of such a loading component is that the instability modes present above the threshold must drift along the crack front during its propagation. This prediction may be useful for future theoretical interpretations of a number of experiments where such a drifting motion was indeed observed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

High-resolution absorption spectroscopy of room-temperature and jet-cooled ammonia between 59,000 and 93,000 cm -1

Here, we present new high-resolution photoabsorption spectra of ammonia spanning the region between 59,000 cm -1 and 93,000 cm -1 that were recorded by using the Fourier Transform Spectrometer at the Synchrotron SOLEIL. This region extends from just above the Franck-Condon envelope for the $\tilde{A}$ 1 $A$ 2 " ← $\tilde{X}$ 1 $A$ 1 ' transition to well above the NH 3 + $\tilde{X}$ + 2 $A$ 2 " ionization threshold. The spectra were recorded at a measured resolution of 0.23 cm -1 in both a room-temperature cell (293 K) and in a slit-jet supersonic expansion (~70 K). The absolute photoabsorption cross section with an uncertainty of ±5% is also reported for the room-temperature spectrum. The present resolution is a factor of 10 – 100 times higher than in other recently reported broad band spectra of ammonia, and many of the observed bands show partially resolved rotational structure. We have attempted to assign this structure for a number of these bands. The oscillator strengths extracted from the data are in good agreement with previous measurements but, in the case of structured bands, the present higher resolution measurements return higher peak absorption cross sections, that increase further when the sample is cooled. The present higher resolution spectra suggest that a number of previous vibronic band assignments that were based on quantum defect considerations may require some revision. Finally, we discuss the substantial differences between the photoabsorption and photoionization data just above the first ionization threshold.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Strength and rupture geometry of un-irradiated C26M FeCrAl under LOCA burst testing conditions

Ferritic iron-chromium-aluminum (FeCrAl) alloys are an accident tolerant fuel candidate to replace the incumbent Zr-based claddings. Nuclear grade FeCrAl alloys are marked by superior high temperature mechanical behavior and exceptional steam oxidation resistance, both of which increase safety margins during accident scenarios. In the present study, the loss of coolant accident (LOCA) burst behaviors of three un-irradiated commercially fabricated cladding materials in a simulated LOCA environment were compared: (1) T35Y2, a 1 st generation nuclear grade FeCrAl, (2) C26M, a 2 nd generation nuclear grade FeCrAl, and (3) Zircaloy-2. Both FeCrAl alloys showed improved mechanical strength and steam oxidation resistance compared to Zircaloy-2. C26M claddings burst at significantly higher temperatures for all tested engineering hoop stresses, had limited ballooning, and demonstrated preferential fuel retention behavior in terms of burst opening area and length. High temperature tensile data for C26M is also presented. For both un-irradiated FeCrAl alloys, it was found that a distinct “threshold” burst stress signified the transition between small and large openings. Finally, higher threshold hoop stresses were associated with higher uniaxial strength for the FeCrAl alloys, indicating that tensile data, rather than creep data, could be useful for predicting rupture size and assessing fuel dispersal concerns.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Study of hydride reorientation and ductility of SRA ZIRLO and PRXA ZIRLO using ring compression testing (RCT)

Before dry storage, spent nuclear fuel is dried at high temperatures, which induces hydride dissolution. Radial hydride particles precipitate when cooled under a stress above a threshold stress. This process can severely degrade the ductility of cladding tubes. Zirconium alloys with different microstructures, such as grain boundary density, were quantified and studied to examine their effect on hydride reorientation. The ring compression loading mode creates a range of stress states depending on the location within the ring with respect to the applied load, producing various hydride morphologies that can be used to study the effects of microstructures on hydride reorientation. Finite element modeling was performed to calculate the hoop stress, which is the dominant stress, during hydride reorientation. These results were coupled with hydride morphology to determine the threshold stress for hydride reorientation, depending on the microstructure. In conclusion, the samples were then mechanically tested using ring compression to evaluate the ductility of zirconium alloys as a function of different hydride morphologies.

Hydride embrittlement↗
DOE OSTI2021

Flow reduction of hydrocarbon liquid in silica nanochannel: Insight from many-body dissipative particle dynamics simulations

A modified many-body dissipative particle dynamics (mDPD) model recently developed for realistic mesoscale multiphase flow simulations is rigorously parameterized, calibrated, and applied for elucidating the flow mechanisms of hydrocarbon liquids (i.e., heptane in this work) in amorphous silica cylindrical nanochannels with inner diameters ranging from 4.5 to 22.5 nm. The simulation results suggest the presence of a strong threshold of pressure gradient under which heptane cannot be driven to flow. The threshold for the 4.5 nm diameter pore is 10 to 100 times as high as for the 9–22.5 nm diameter pore, highlighting a remarkable nanoconfinement effect. Fluid viscosity is found to exhibit a shear-thinning phenomenon with intensity to weaken with increasing channel diameter — a phenomenon not observed in nanochannel flow of liquid water and gas in literature. Most remarkably, the radial profiles of average longitudinal flow velocity fitted by the modified Hagen-Poiseuille equation showed a negative slip length (–2.5% to –0.5% relative to the diameter) and a reduction of apparent permeability by 16% to 23%. Furthermore, this finding suggests silica nanochannels tend to deter hydrocarbon flow, a phenomenon that is opposed to the flow enhancement reported in most of the prior nanochannel flow studies in literature.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2020

Beta-delayed charged-particle spectroscopy using TexAT

β-delayed charged-particle emission is a sensitive probe of three-body decays in light nuclei. Time Projection Chambers (TPCs) offer a significant advantage over traditional charged-particle spectroscopy techniques due to a low-energy threshold and a high-geometric efficiency (≈ 4π) which are essential for use with radioactive ion beams where the beam intensities are limited. The technique for high-sensitivity spectroscopy of β-delayed charged-particle emission is shown to be possible using the Texas Active Target (TexAT) TPC in conjunction with the General Electronics for TPCs (GET) system. The benchmark case studied was that of 12 N β-decay to the first α-unbound state in 12 C, the Hoyle state. Here, half-life and branching ratio measurements are presented and are in good agreement with previous studies. The efficacy of using TPCs to study such a near-threshold state and disentangle the three-body dynamics of the decay products is demonstrated.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Parameter dependencies of the experimental nitrogen concentration required for detachment on ASDEX Upgrade and JET

While current tokamak experiments are beginning to use real-time feedback control systems to manage the plasma exhaust, future tokamaks still require validation of theoretical models used to predict the threshold impurity concentration required to sufficiently reduce the power and particle fluxes to the divertor. This work exploits new spectroscopic measurements of the divertor nitrogen concentration, c n , in partially detached N 2 -seeded H-mode plasmas on ASDEX Upgrade (AUG) and JET with the ITER-Like Wall (JET-ILW) to test the parameter dependencies of the power flowing to the outer divertor, P div,outer , and the separatrix electron density, n e.sep . A least-squares regression of the AUG measurements demonstrates that the threshold c n required for detachment scales as $c_n∝P^{1.19±0.32}_{div,outer}n^{-2.77±0.36}_{e,sep}$. This scaling of n e,sep is also consistent with the measurements from JET which, at constant P div,outer , show $c_n∝n^{-2.43±0.27}_{e,sep}$. The dependencies of P div,outer and n e.sep is demonstrated over at least a factor of two change in both parameters and indicates a stronger dependence on n e.sep in comparison to the Lengyel model, which could be due to the assumption in this model that the heat flux channel width is independent of density. This first assessment of detachment scaling with impurity seeding highlights the need for further analysis of the systematic uncertainties of the measurement and more consistent scenarios from more tokamaks to investigate the machine size scaling.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Integral LOCA fragmentation test on high-burnup fuel

Increasing the fuel burnup limit in light water reactors is sought to enhance fuel cycle economics and requires establishing a technical basis. Experimental observations of severe fuel fragmentation under loss-of-coolant-accident conditions at Halden and Studsvik had raised the need for additional considerations during the development of this technical basis. These test data suggested that the burnup threshold for high burnup fuel fragmentation may be influenced by pre-transient power. Additional loss-of-coolant-accident test data is therefore valuable to complement these tests and enhance the current state of understating. Oak Ridge National Lab has developed the Severe Accident Test Station capable of examining the oxidation kinetics and accident response of irradiated fuel and cladding materials for design basis accident and beyond design basis accident scenarios. Severe Accident Test Station provides various temperature profiles, steam, and the thermal shock conditions necessary for integral loss of coolant accident testing, defueled oxidation quench testing, and high-temperature beyond design basis accident testing. Severe Accident Test Station has been successfully installed and demonstrated in the Irradiated Fuels Examination Laboratory at Oak Ridge National Lab. Furthermore, descriptions of the in-cell re-fabrication capabilities and assembly of the loss-of-coolant-accident test train are provided. Installation of the Severe Accident Test Station system and in-cell re-fabrication restores United States capability to examine postulated and extended loss-of-coolant-accident conditions on spent fuel and cladding and provides a platform for evaluating advanced fuel and accident-tolerant fuel cladding concepts. Lastly, three in-cell integral loss-of-coolant-accident test were performed in the Severe Accident Test Station and compared to the Nuclear Regulatory Commission sponsored loss-of-coolant-accident test as well as the original loss-of-coolant-accident test performed at Argonne National Lab. Finally, the results of these tests as well as all publicly available integral loss-of-coolant-accident test were used to validate a threshold for high burnup fuel fragmentation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Note on the definitions of branching ratios of overlapping resonances

Branching ratios for the decay of hadrons with large width or near thresholds depend on their definition. We test different definitions and show that rather different branching ratios can be obtained. For wide resonances and for sequential decays with wide intermediate resonances, integration over the spectral functions is mandatory. The tests are performed exploiting the latest solution of the Bonn-Gatchina multi-channel analysis and published values for residues of light scalar mesons. For a resonance overlapping with a threshold, in case its pole lies in a non-adjacent sheet, we show how the total width, needed for the branching ratios, does not correspond to the imaginary part of the pole position. We use the Madrid-Krakow dispersive parameterizations to illustrate this situation with the f 0 (980).

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Response of PETN detonators to elevated temperatures

In the present study, commercially available detonators with pentaerythritol tetranitrate (PETN) were subjected to elevated temperatures. The detonators were thermally ignited over a range of heating rates to measure ignition delay time and assess detonator violence. The violence of the detonator was quantified by measuring the velocity of the detonator closure disc (or “flyer”). The maximum flyer velocity of a thermally ignited detonator was comparable in magnitude to that obtained by initiating a room temperature pristine detonator with an exploding bridge wire (under the same confinement); however, the high flyer velocity was not an indication of deflagration to detonation transition (DDT) in the thermally ignited detonator. The detonator responded more violently than a thermally ignited detonator when initiated at 95% of the ignition delay time. Furthermore, inoperability thresholds were also measured by varying the detonator temperature and the threshold was found to be sensitive at detonator temperatures below the melting point of PETN.

42 ENGINEERING↗
DOE OSTI2022

Hydrodynamics and Load Shedding Behavior of a Variable-Geometry Oscillating Surge Wave Energy Converter (OSWEC)

In order to improve their long-term viability, wave energy converters (WECs) need to be able to shed loads when a threshold wave condition is exceeded. As shown by Tom et al. (2016) [1], provision of adjustable flaps within the body of an oscillating surge wave energy converter (OSWEC) allows wave energy to pass through the device. A control system may then be able to open and close the flaps when waves approaching the device exceed preset thresholds. The variable-geometry OSWEC (VG-OSWEC) concept studied in this paper is a bottom-hinged, rectangular wave paddle with five flaps of elliptical cross-section embedded into the face of the paddle. System ID tests were conducted on this VG-OSWEC device at a 1:14 scale in a wave basin. Free decay tests showed that the damping was distinctly nonlinear when the flaps were fully open, and the natural frequency increased by 40% when compared with the flaps in a fully closed configuration. Tests with regular wave conditions were used to develop the response amplitude operator for the rotational motion about the hinge. These response amplitude operator results when compared with numerical simulations run using WEC-Sim/WAMIT and ANSYS AQWA, show strong agreement with the flap open and closed conditions. The regular-wave condition measurements also show that the wave excitation moment about the hinge was reduced by up to 60% when the flaps were fully open. The experiments serve to demonstrate the potential of the variable geometry design to shed loads and survive harsh ocean environments.

load shedding↗