Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “tables”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

The NSLS-II Control Network Design

The required positioning tolerances are an essential part of the survey and alignment design. The following tables show the requirement of storage ring. Table 1 provides the required global tolerances, while Table 2 outlines the relative tolerances for the NSLS-II girder-to-girder positioning. These tolerances dictate the instruments and methods necessary to obtain the positioning goals. The global tolerance is a little bit relaxed, but the ± 0.10 mm positioning requirement of adjacent girders is rather strict if the larger dimension and probable foundation settlement is considered.

43 PARTICLE ACCELERATORS↗

AGS Longitudinal emittance measurements for upcoming RHIC low energy gold runs

Many longitudinal emittance (ε) measurements were made in the AGS towards the end of Run 18 with Au from EBIS at the flattop energies to be used for the upcoming RHIC low energy runs. The primary motivation for this was to determine what emittances and bunch intensities could be provided by the injectors. The measurements were also taken for many different configurations to try to gain a better understanding of the observed ε growth on the acceleration ramp in the hope of finding some way to reduce it. The tentative requirements for the 5 energies are shown in Table I. Different parameters were varied depending on the requirements at each extraction energy and they included: The type of AGS merge, the main magnet voltage banks (Pulsed and Flattop) used for ramping, the ramp and flattop Rf voltages, and the amount of bunch squeezing after the merge. The measurements were made over a period of a month (May 15 to June 15), starting with the lowest energy and generally working up to the highest. The measurements for each energy, from lowest to highest, are in Tables II through VI, respectively. Figures 4 through 7 also show some of the more relevant data for the first four energies. Table VII (and Figure 8) show the data for the best candidates for the different energies. Some of the setups may seem irrelevant, but at the time that was not clear. This is particularly true in cases where the ramping and flattop voltages were varied. On the other hand, with the benefit of hindsight, there are setups that should have been checked but weren’t.

43 PARTICLE ACCELERATORS↗

The NSLS-II Control Network Design

The required positioning tolerances are an essential part of the survey and alignment design. The following tables show the requirement of storage ring. Table 1 provides the required global tolerances, while Table 2 outlines the relative tolerances for the NSLS-II girder-to-girder positioning. These tolerances dictate the instruments and methods necessary to obtain the positioning goals. The global tolerance is a little bit relaxed, but the ± 0.10 mm positioning requirement of adjacent girders is rather strict if the larger dimension and probable foundation settlement is considered. control network. Therefore, whether the goals can be obtained is mainly dependent on the performance of control network. The shape of control network defines the global alignment accuracy, while the relative position relationships of monuments determine the relative positioning accuracy between girders. When deciding the strategy of survey and alignment techniques, the instrumentation and approach of light sources have been built and are still in construction are investigated. State-of-the art equipment and methods will be employed. NSLS-II covers an area of about one-eighth of a square kilometer with a radius of ~126 m and a circumference of ~792 m. Depending on the size of the system to be constructed, primary and secondary control networks are required to achieve these tolerances. Primary control network will provide global control for different tunnels, and it should possess a relative point accuracy of better than ± 3 mm for all the storage ring monuments. Secondary control network will direct the alignment of girders in tunnel with the ability to ensure the final ± 0.10 mm positioning accuracy. The experiences from accomplished light source indicate that: for a dimension like NSLS2, primary control network can obtain a point accuracy of better than ± 1 mm easily, while secondary control network can obtain a relative point accuracy of ± 0.08 mm. With this expectation, the tolerance can be achieved for both the global and relative situation. Take the relative positioning requirement as an example, with 2 control network error of ± 0.08 mm, instrument tie-in error of ± 0.04 mm, and residual error of ± 0.04 mm, according to error propagation formula, the final alignment error should be better than ± 0.1 mm. Correspondingly, if a better control network accuracy can be achieved, the requirement for the residuals can be looser. The further alignment accuracy improvement will be realized by a smoothing process to assure the better position relationship between adjacent girders. The following simulation will perform error analysis to evaluate the estimated accuracy of NSLS II control network.

36 MATERIALS SCIENCE↗

Transportation Energy Data Book: Edition 38

The Transportation Energy Data Book: Edition 38 is a statistical compendium prepared and published by Oak Ridge National Laboratory (ORNL) under contract with the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Vehicle Technologies Office. Designed for use as a desk-top reference, the Data Book represents an assembly and display of statistics and information that characterize transportation activity, and presents data on other factors that influence transportation energy use. The purpose of this document is to present relevant statistical data in the form of tables and graphs. The latest edition of the Data Book is available via the Internet. This edition of the Data Book has 13 chapters which focus on various aspects of the transportation industry. Chapter 1 - focuses on petroleum; Chapter 2 - energy; Chapter 3 - highway vehicles; Chapter 4 - light vehicles; Chapter 5 - heavy vehicles; Chapter 6 - alternative fuel vehicles; Chapter 7 - transit and shared mobility; Chapter 8 - fleet vehicles; Chapter 9 - household vehicles; Chapter 10 - nonhighway modes; Chapter 11 - transportation and the economy; Chapter 12 - greenhouse gas emissions; and Chapter 13 - criteria pollutant emissions. The sources used represent the latest available data. There are also three appendices which include detailed source information for some tables, measures of conversion, and energy tables and figures with electricity generation and distribution taken into account. A glossary of terms is also included for the reader’s convenience.

02 PETROLEUM↗

Stage B Uranium Sequestration Amendment Delivery Monitoring Using Time-Lapse Electrical Resistivity Tomography

The Hanford Site 300 Area lies adjacent to the Columbia River, approximately 5 km north of Richland, Washington. Past waste disposal practices in the 300 Area resulted in vadose zone uranium contamination beneath former infiltration ponds and trenches. Stage-driven water table fluctuations and river water intrusion facilitate mobilization of uranium from contaminated sediments in regions periodically occupied by the water table (i.e., the periodically rewetted zone or PRZ), thereby raising groundwater uranium concentrations above the maximum allowable contaminant level for uranium. This report documents the ERT imaging operations and interpretation of imaging results in terms of the extent of amendment delivery (including phosphate and/or carrier fluid) within the treatment area. Based on the interpretation, amendment delivery to the LVZ and PRZ was observed to be variable between each of the three imaging clusters, as shown in Figure S.1. Amendment transport in Cluster 1 exhibited significant lateral flow in comparison to Clusters 2 and 3, resulting in a final amendment distribution throughout a large portion of the LVZ and PRZ sediment between the injection wells. Cluster 2 exhibited good amendment delivery in the LVZ only near the injection wells. In the PRZ at Cluster 2, amendment was effectively distributed through the full distance between injection wells. Cluster 3 exhibited the smallest amount of lateral flow and amendment was primarily distributed in the LVZ and PRZ very near the injection wells. Imaging results below the water table suggest that more amendment entered the groundwater in Cluster 2 and Cluster 3 than in Cluster 1.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Monthly Sewer Monitoring Report for LLNL Livermore Site, April 2020

Lawrence Livermore National Laboratory (LLNL) collects effluent samples from its sewer outfall at the B196 Sewer Monitoring Station (SMS). Effluent flow-proportional composite samples are collected at the SMS on a daily (midnight-to-midnight), weekly (Thursday through Wednesday), and “monthly” (composited from daily) basis; effluent grab samples are also collected each month at that same location. Certified contract laboratories analyzes these compliance samples, and results (Tables 1–3) are used to establish LLNL compliance with the 2019–2020 Wastewater Discharge Permit (Permit 1250) granted by the City of Livermore Water Resources Division (WRD). Supplemental analyses for biochemical oxygen demand (BOD) and total suspended solids (TSS) are performed onsite and reported (Table 4) for the calculation and assessment of sewer service charges. Quarterly, effluent is sampled for metals (24-hour composite) and cyanide (grab sample) concentrations (mg/L). The results are presented in Table 5. In addition to the sampling noted above, the SMS continuously monitors LLNL sewage effluent in real-time for flow rate, pH, metals, and radioactivity. Standard measurement methods are used to monitor flow and pH to determine permit compliance. Unique nonstandard analytical methods monitor for the presence of metals and radioactivity using x-ray fluorescence (XRF) and gamma spectroscopy, respectively. If an anomalous condition is detected by the monitoring system, an alarm activates LLNL’s Sewer Diversion Facility (SDF) and Livermore Water Reclamation Plant (LWRP) operators are notified that a potential release has occurred.

54 ENVIRONMENTAL SCIENCES↗

Effects of Experimental Warming and Elevated CO 2 on CO 2 and CH 4 Fluxes in an Ombrotrophic Black-Spruce. Final Report

High latitude peatlands and permafrost soils contain nearly half of the soil carbon pool on Earth. The potential for large soil C stocks in peatlands and permafrost to become a positive feedback to climate change by increasing net emissions of CO₂ and CH₄ to the atmosphere is a subject of grave concern. This research was conducted at the Spruce and Peatland Responses Under Changing Environments (herein SPRUCE) experimental facility, located in the USDA’s Marcell Experimental Forest in northern Minnesota. The site is dominated by Picea mariana [herein black spruce], ericaceous shrubs and Sphagnum spp. Ten 12m-diameter open top chambers expose portions of the 8.1-ha S1 bog to warming up to +9°C in 2.25°C increments at ambient and elevated CO₂ (eCO₂, 900ppm). The Finzi lab group began manual measurements of CO₂ and CH₄ fluxes and their C-isotopic compositions in 2014. With funding from the DOE-TES program automated measurements of these species began in 2015. With a one-year no cost extension we were able to make measurements through the 2018 growing season. Across the study period we find that experimental warming of the peatland significantly increases the flux of CO₂ and CH₄ to the atmosphere. The highest temperature treatments had the highest fluxes. As peatlands have complex topography and water table dynamics, many of these results were contingent upon the topographic location in which the measurements were made. In the raised portions of the peatland divorced from the water table, fluxes of CO₂ were high and fluxes of CH₄ were low. By contrast, in the lower portions of the peatland surface, which is at or very near the water table, fluxes of CH₄ were substantially higher. A significant fraction of the total annual CH₄ flux was derived from episodic ebullitive fluxes. The occurrence and size of these ebullitive fluxes also increased with temperature. Experimental fumigation of the black spruce peatland with elevated concentrations of atmospheric CO₂ [herein eCO₂] also had significant effects on emissions of greenhouse gasses. In general these effects were far more subtle than the effects of rising temperature. This indicates that temperature change more than atmospheric chemistry changes are affect the belowground cycle of C in the peatland. Overall, this study shows that boreal peatlands are highly sensitive to changes in temperature. The warmer it becomes the more C will be lost from the peatland to the atmosphere. This appears to create a positive feedback loop that is likely to enhance the concentration of greenhouse gases in the atmosphere.

54 ENVIRONMENTAL SCIENCES↗

Oak Ridge National Laboratory Technical Input for the Nuclear Regulatory Commission Review of the 2017 Edition of ASME Section III, Division 5, ‘High Temperature Reactors’

To assist the Nuclear Regulatory Commission in its decision making on endorsement of the American Society for Mechanical Engineers Boiler and Pressure Vessel Code Section III, Division 5 (2017 Edition) for development of advanced non-light water reactors, the following Division 5 portions were reviewed: Article HBB-2000 Material; Article HCB-2000 Material; Article HGB-2000 Material; Mandatory Appendix HBB-I-14 Tables and Figures; and, Nonmandatory Appendix HBB-U Guidelines for Restricted Material Specifications to Improve Performance in Certain Service Applications. In addition to the 2017 Edition, the same parts of the 2019 Edition have also been reviewed as indicated in various sections of the report. This review was conducted by a collaboration of national laboratory and private sector participants with significant industrial experience, including some heavy lifting and deep diving from Clarus Consulting, LLC., all intended to achieve an objective, independent, and practical perspective. The report provides recommendations, descriptions of the evaluation methods, and the source references for the data used. To build confidence required for endorsement of the Code, this review was conducted as a verification and validation of the above Code contents. The objective of verification is to ensure that the Code is free of error – direct or implied; contains the information needed for its use, including proper coverage of the Code-specified materials for the intended application, and completeness and adequacy of references to other portions of the Code. The objective of validation is to authenticate that the Code tabulations and graphs represent design inputs consistent with what are determined using rules and methods specified by the Code. The authentication process used data that were assembled and/or generated independent of Code development, while the methods of analysis followed Code-specified methods where appropriate. The designated portions for this review cover the five alloys codified for high temperature reactor applications in Division 5, i.e. 316 SS, 304 SS, 800H, 2¼Cr-1Mo, and 9Cr-1Mo-V, regarding their general requirements, permitted specifications and design stress intensity values for pressure-retaining applications, deterioration in service, fatigue acceptance test, permissible weld materials, tensile and yield strength, expected minimum stress-to-rupture values (including for Alloy 718), weld stress rupture factors, permissible materials for bolting use, and restricted specifications in certain service applications. Additionally, stress intensity values for bolting materials including 316 SS, 304 SS and alloy 718 were reviewed. Analysis and discussion are also provided on contents outside of these designated Code portions where it was deemed relevant and necessary to develop a technically sound understanding of issues relating to the designated portions. Due to unavailability of sufficient test data on welds during the review period, the weld stress rupture factors in Tables HBB-I-10.14A to E, which cover a total of ten tables for the five alloys welded with twenty-eight different weld metals (some with similar properties), have been deferred to a future review effort. The review identified mainly two types of issues. The first type includes instances where the Code is found factually incomplete or incorrect, such as obsolete materials specifications listings, missing tabulation of stresses for bolting. Changes to the Code are recommended in these cases. The second type of issue includes instances where the Code tabulations and graphs are found to be less conservative than the review analysis results. In these cases, recommendations are made for further review and consideration where the difference in conservatism exceeds 10%, which is our threshold for questioning technical adequacy, meriting a risk assessment by the Nuclear Regulatory Commission and/or reactor designers. It is noted that this effort has been executed using all available data and established methods of analysis, including methods and criteria specified and used by the Code. As such, the findings that are presented in quantitative detail, in a format for convenient comparison with the Code, and with identification of where further review is recommended, should provide a sound technical basis for decisions about quantifying the implications of the reduced design margins and technical adequacy/inadequacy to form a basis for conditioning specific Code tabulation values on endorsement. Recommendations for specific changes to the Code, however, entail design conservatism considerations beyond the scope of this review effort, and are not made in this report.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

PORFLOW modeling of Vadose zone flow and transport for the E-area intermediate level vault

In support of the E-Area Performance Assessment, a two-dimensional model of water flow and radionuclide transport through the E-Area Intermediate Level Vault (ILV) and local vadose zone has been developed using the PORFLOWTM software. The purpose of the model is to calculate flux to the water table for radionuclides eluted from the ILV during its operational life, the period of institutional control, and times following site closure. Results of model calculations will be used by a three-dimensional PORFLOW model of transport through the aquifer to determine radionuclide concentrations at a hypothetical 100 meter well and at the site boundary where contaminated groundwater could be assessed by members of the public following site closure. While newly developed, the model structure closely follows that used in the 2008 PA while incorporating a refined computational mesh, updated material properties for the vadose zone soil and vault concrete, revised infiltration rates, and new solid-liquid distribution coefficients. The model also addresses degradation of concrete hydraulic properties by blending soil and concrete water retention curves over a 500 year period. That is, the hydraulic properties of ILV concrete start out as fresh concrete at the time of site closure and degrade to soil properties over a 500 year time period. This approach has not been used previously in E-Area PA’s. The model has been used to calculate water flow through the ILV vadose zone and, on a trial basis, transport of a limited number of radionuclides from the waste region inside the ILV to the water table. Figure ES-1 provides a view of the model and an example of water flow after the concrete has substantially degraded. Figure dimensions are in centimeters. The red area in the left hand side figure is the waste disposal region within the ILV. Colored bands in the figures indicate different soil and concrete regions. Figure ES-2 shows a calculation of flux to the water table (mol/yr) for U-234 and its one-year half-life decay chain (U-234 → Th-230 → Ra-226 → Pb-210). Pb-210 flux is too small to show on the same scale used for Th-230 and Ra-226 in Figure ES-2. The model has also been used to make a preliminary evaluation of the release of tritium from TPBAR disposal containers that will be place in the ILV. A separately calculated tritium release rate as a function of time was used as a source in the PORFLOW model. The TPBAR disposal schedule and tritium release rate differ from the values used in the 2008 PA. Results from these initial trial runs are compared to calculations made for the 2008 PA ILV analysis. In brief, a new PORFLOW model of flow and transport through the ILV vadose zone has been developed and tested. The model is ready to be used for PA calculations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Generation of Bright Soft X-ray Laser Beams (Final Report)

The project goal was to demonstrate new compact soft x-ray lasers emitting high energy ultrashort pulses at shorter wavelengths and increased repetition rates by amplification in atomic transitions in high density laser-created plasmas. To demonstrate these lasers we developed new high power solid state lasers. The project succeeded in demonstrating the shortest wavelength compact soft x-ray laser to date, 6.85 nm wavelength, and the highest repetition rate table-top soft x-ray laser, 400 Hz. We also applied these compact soft x-ray laser sources to determine the composition of materials with nanoscale resolution using a new technique that combines soft x-ray laser ablation with mass spectrometry, and we demonstrated that these lasers are capable of acquiring nanoscale resolution holograms with picosecond time resolution. The combination of an increased pumping efficiency with increased repetition rates can yield soft x-ray laser beams with an unprecedented average power on a table-top for applications demanding a high photon flux. We have demonstrated that the efficiency of plasma-based laser-pumped soft x-ray lasers can be significantly increased by detailed pulse shaping of the pump laser using a new pulse synthesizer. Results include the demonstration of 18.9 nm wavelength laser operation at a record 400 Hz repetition rate, and the extension of repetitive gain-saturated plasma-based table-top x-ray lasers to the shortest wavelength to date, 6.85 nm. Laser amplification was also observed at wavelengths as short at 5.8 nm by isolectronic scaling in Ni-like lanthanide ions. We have also conducted simulations to explore the possibility of demonstrating gain saturated atomic x-ray lasers near the carbon K-edge, in the “carbon window” for the first time. The work conducted under this program also includes the use of compact soft x-ray lasers in applications to problems of chemical interest, such as isotopic composition mapping of micron-size uranium particles with nanoscale resolution, and nanoscale resolution depth profiling analysis of CoNCN-coated electrodes for water oxidation catalysis. We also demonstrated single-shot high resolution soft x-ray Fourier transform holography over a broad 7 µm diameter field of view with ~ 5 ps temporal resolution.

74 ATOMIC AND MOLECULAR PHYSICS↗

Transportation Energy Data Book: Edition 39

The Transportation Energy Data Book: Edition 39 is a statistical compendium prepared and published by Oak Ridge National Laboratory (ORNL) under contract with the U.S. Department of Energy, Office of Energy Efficiency and Renewable Energy, Vehicle Technologies Office. Designed for use as a desk-top reference, the Data Book represents an assembly and display of statistics and information that characterize transportation activity and presents data on other factors that influence transportation energy use. The purpose of this document is to present relevant statistical data in the form of tables and graphs. The latest edition of the Data Book is available via the Internet (tedb.ornl.gov).This edition of the Data Book has 13 chapters which focus on various aspects of the transportation industry. Chapter 1 focuses on petroleum; Chapter 2 – energy; Chapter 3 – highway vehicles; Chapter 4 – light vehicles; Chapter 5 – heavy vehicles; Chapter 6 – alternative fuel vehicles; Chapter 7 – transit and other shared mobility; Chapter 8 – fleet vehicles; Chapter 9 – household vehicles; Chapter 10 – nonhighway modes; Chapter 11 – transportation and the economy; Chapter 12 – greenhouse gas emissions; and Chapter 13 – criteria pollutant emissions. The sources used represent the latest available data. There are also three appendices which include detailed source information for some tables, measures of conversion, and energy tables with electricity generation and distribution. A glossary of terms is also included for the reader’s convenience.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Data Processing Package for Cyclic Integrated Reversible Bending Fatigue Testing

A data processing software package has been introduced. The package was developed using MATLAB with the aid of the Curve Fitting Toolbox. The package is made up of four modules: pre-processing, data processing for static testing, data processing for monitoring, and data processing for measurements. CIRFT data are structured with multiple levels of architecture involving group, specimen, session, and scan/block. The degree of complexity of the data structure depends on whether a test is static or cyclic.The test results are presented in figures, scatter plots, and tables. For static testing, the output in tables provides bending mechanical properties and characteristic points of moment–curvature relation: flexural rigidities in linear segments of loading and unloading stages, intersection points between characteristic segments of the curve, and equivalent stress and strain quantities. For cyclic testing, the table output lists control and fatigue life and responsive/dependent quantities including moment, curvature, flexural rigidity, flexural hysteresis, rigidity phase angle, and equivalent stresses and strains. In addition, derivatives such as half-gage length and sensor spacing correction are included. The output also provides standard deviations of the reported quantities when they are applicable or available. The data processing package can serve as a fundamental characterization tool in mechanical study of materials. The package is intended primarily for data processing for the CIRFT process and can also be used in applications for which similar testing requirements exist.

36 MATERIALS SCIENCE↗

NRAP-Open-IAM: FutureGen2 Component Models

This report describes the development and testing of three component models for NRAP-Open-IAM, the National Risk Assessment Partnership’s open-source integrated assessment model. The FutureGen2 Lookup Table Reservoir component model is based on interpolation of data from a set of lookup tables. The lookup tables contain pressures and saturations predicted by multiphase flow simulations performed with a reservoir simulator. The FutureGen2 Above Zone Monitoring Interval (AZMI) component is a surrogate model that can be used to estimate the impact that carbon dioxide (CO 2 ) and brine leaks from the CO 2 storage reservoir at the FutureGen 2.0 site might have had on overlying aquifers or monitoring units were a leak to occur. The model estimates the size of “impact plumes” according to five metrics: pH, Total Dissolved Solids (TDS), pressure, dissolved CO 2 and temperature. The FutureGen2 Aquifer component is similar, but is limited to four metrics: pH, Total Dissolved Solids (TDS), pressure, and dissolved CO 2 . The input parameters for each model are the same, but the Aquifer component is applicable to depths between 100 m and 700 m and the AZMI component is applicable from depths between 700 m and 1050 m.

42 ENGINEERING↗

NRAP-Open-IAM: Open Wellbore Component (V.2.0)

The Open Wellbore component of NRAP-Open-IAM is applicable to the calculation of Area of Review at a carbon storage site and fast estimation of dense gas dispersion from multiple continuous CO 2 surface leakage sources for risk assessment. The Open Wellbore Component of NRAP-Open-IAM is a lookup table model based on the drift-flux approach. The National Research Assessment Partnership’s second-generation integrated assessment model, NRAP-Open-IAM, is open-source software written in Python for use in performance and quantitative risk assessment of geologic carbon storage (GCS) systems. The look-up table for open well leakage is an updated version the previous model which provides finer resolution of reservoir depth and more accurate fluid properties than the previous open well look-up table, especially in calculating the gas (CO 2 -rich) phase properties. The component model input parameters include the reservoir transmissivity, aquifer transmissivity, brine salinity, well radius, and well top and bottom depths. The reservoir transmissivity and brine salinity were set to values consistent with the reservoir component, and the well top and bottom depths varied with location. The possible outputs from the Open Wellbore component are leakage rates of CO 2 and brine to either an aquifer or atmosphere, depending on the depth of the well top. Several python test scripts are presented that demonstrate that the Open Wellbore component works correctly. Use of the open wellbore model in NRAP-Open-IAM may result in a large CO 2 leakage rates, comparable to the leakage rates of CO 2 blow out.

54 ENVIRONMENTAL SCIENCES↗

Improving Predictive Capability in REHEDS Simulations with Fast, Accurate, and Consistent Non-Equilibrium Material Properties

Predictive design of REHEDS experiments with radiation-hydrodynamic simulations requires knowledge of material properties (e.g. equations of state (EOS), transport coefficients, and radiation physics). Interpreting experimental results requires accurate models of diagnostic observables (e.g. detailed emission, absorption, and scattering spectra). In conditions of Local Thermodynamic Equilibrium (LTE), these material properties and observables can be pre-computed with relatively high accuracy and subsequently tabulated on simple temperature-density grids for fast look-up by simulations. When radiation and electron temperatures fall out of equilibrium, however, non-LTE effects can profoundly change material properties and diagnostic signatures. Accurately and efficiently incorporating these non-LTE effects has been a longstanding challenge for simulations. At present, most simulations include non-LTE effects by invoking highly simplified inline models. These inline non-LTE models are both much slower than table look-up and significantly less accurate than the detailed models used to populate LTE tables and diagnose experimental data through post-processing or inversion. Because inline non-LTE models are slow, designers avoid them whenever possible, which leads to known inaccuracies from using tabular LTE. Because inline models are simple, they are inconsistent with tabular data from detailed models, leading to ill-known inaccuracies, and they cannot generate detailed synthetic diagnostics suitable for direct comparisons with experimental data. This project addresses the challenge of generating and utilizing efficient, accurate, and consistent non-equilibrium material data along three complementary but relatively independent research lines. First, we have developed a relatively fast and accurate non-LTE average-atom model based on density functional theory (DFT) that provides a complete set of EOS, transport, and radiative data, and have rigorously tested it against more sophisticated first-principles multi-atom DFT models, including time-dependent DFT. Next, we have developed a tabular scheme and interpolation methods that compactly capture non-LTE effects for use in simulations and have implemented these tables in the GORGON magneto-hydrodynamic (MHD) code. Finally, we have developed post-processing tools that use detailed tabulated non-LTE data to directly predict experimental observables from simulation output.

36 MATERIALS SCIENCE↗

Generic National Nuclear Forensics Library Implementation

This document provides instructions for the database implementation for national nuclear forensic library (NNFL) using a relational database. While there are many software options that can be used to implement an NNFL database, in this document we reference an Oracle database for the implementation. The principles related here can be applied to any relational database structure. The design revolves around two main types of data: Samples and Results. Samples are materials or descriptions of materials; results are the results of analyses of those samples. All additional tables exist as a result of the normalization process. The remaining tables/entities have keys that are referenced by the Result/Sample tables via foreign key constraints. This allows for the enforcement of different relationships between the tables such as one-to-one, one-to-many, many-to-many. This process helps to ensure that valid data is entered, optimizes database performance and avoids data redundancies.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A simulation study of test fixture attachment points for vibration test optimization (MEEN 5440 Final Project)

The aerospace industry uses vibration shaker tables to perform component durability testing. These dynamic environments tests often have a hard time replicating the service environment of a component due to a mismatch in the applied force or the boundary condition. Figure 1 shows the desired outcome of a dynamic environments test. The measured responses in a lab test, ideally, should match the measured response of the service environment field test. One way to address the mismatch between field environment and lab environment is with test fixture design. The test fixture attaches the component under test to the shaker table. Single-axis shakers are the industry standard type of shaker table, and, therefore, test fixtures are often rigid in order to minimize cross-axis responses.

42 ENGINEERING↗