Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “room temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

In situ self-ion (Fe + ) irradiation of ODS-FeCrAl alloy fuel cladding materials with different Cr contents: The early stages of Cr-rich α’ phase precipitation

Oxide-dispersion-strengthened FeCrAl (ODS-FeCrAl) alloys are candidate accident-tolerant fuel cladding materials for light water reactors because they demonstrate satisfactory resistance to materials degradation effects such as high-temperature oxidation, radiation-induced swelling, and creep. Their perspective deployment to market is challenged, however, by their inherent susceptibility to irradiation embrittlement caused by the precipitation of the brittle Cr-rich α’ phase at relatively low temperatures (≤475 °C). This work used in situ self-ion irradiation (150 keV Fe + ) in a transmission electron microscope to elucidate the early stages of Cr-rich α’ phase precipitation in three candidate ODS-FeCrAl alloy fuel cladding materials with different Cr contents (10, 12, and 20 wt.%) and microstructures. The early stages of the process resulting in the precipitation of the Cr-rich α’ phase in these three ODS-FeCrAl alloys under Fe + irradiation were investigated at room temperature and 300 °C up to total fluences of 1.7 × 10 15 ions·cm -2 (2 dpa) and 3.4 × 10 15 ions·cm -2 (4 dpa), using three damage dose rates (5 × 10 –5 , 3.3 × 10 –4 , and 2 × 10 –3 dpa·s -1 ). Post-irradiation examination via scanning transmission electron microscopy, energy-dispersive X-ray spectroscopy and electron energy loss spectroscopy suggested that the precipitation of the Cr-rich α’ phase might be promoted by the phase separation of the alloy matrix into Cr-rich and Fe-rich regions. Interestingly, oxygen impurities segregated preferentially in the Cr-rich regions, possibly promoting the radiation-assisted formation of the Cr-rich α’ phase. α’ phase precipitation was more pronounced at room temperature when compared to 300 °C, and it was clearly promoted by the progressive increase in the Cr content of the ODS-FeCrAl alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructural, Oxidation, and Mechanical Behavior of NbTi-Based Refractory Alloys with 5 to 10 Pct Co, Cr, and Ni Additions

NbTi-based refractory alloys with additions of Co, Cr, and Ni represent an interesting medium-entropy alloy system with potential for protective oxide film formation, high strength, and ductility. This study investigates the microstructural evolution, oxidation behavior, and mechanical properties of NbTi-based alloys containing 5 to 10 at. pct Co, Cr, and Ni. CALPHAD predictions suggest that this composition range can be heat treated to obtain a predominantly body-centered cubic matrix phase. Mechanical properties, including microhardness, yield strength, maximum strength, and specific strength are evaluated through isothermal compression tests conducted between room temperature and 800 °C. The oxidation kinetics of these alloys are assessed through discontinuous oxidation tests. Parabolic oxidation kinetics were observed for NbTi–10Ni and NbTi–5Co, while linear oxidation kinetics were found for NbTi–10Cr and NbTi–10(CoCrNi). Microstructures and oxide layers are characterized using X-ray diffraction, electron backscatter diffraction, energy-dispersive X-ray spectroscopy, and scanning electron microscopy. All alloys exhibit significant mechanical softening between room temperature and 800 °C, with elastic-perfectly plastic flow observed at 800 °C. The addition of 10 pct Cr to NbTi resulted in two BCC phases up to 1050 °C, conflicting with CALPHAD predictions of a single-phase solid solution at this temperature, and resulting in higher flow stress at 800 °C. NbTi–10(CoCrNi) exhibited the lowest flow stress at 800 °C despite having more ‘cocktail effect’ potential and insufficient molar fractions of Co, Cr, or Ni to form a desirable protective oxide film.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Magnetic Texture in Insulating Single Crystal High Entropy Oxide Spinel Films

Magnetic insulators are important materials for a range of next-generation memory and spintronic applications. Structural constraints in this class of devices generally require a clean heterointerface that allows effective magnetic coupling between the insulating layer and the conducting layer. However, there are relatively few examples of magnetic insulators that can be synthesized with surface qualities that would allow these smooth interfaces and precisely tuned interfacial magnetic exchange coupling, which might be applicable at room temperature. In this work, we demonstrate an example of how the configurational complexity in the magnetic insulator layer can be used to realize these properties. The entropy-assisted synthesis is used to create single-crystal (Mg 0.2 Ni 0.2 Fe 0.2 Co 0.2 Cu 0.2 )Fe 2 O 4 films on substrates spanning a range of strain states. These films show smooth surfaces, high resistivity, and strong magnetic responses at room temperature. Furthermore, local and global magnetic measurements further demonstrate how strain can be used to manipulate the magnetic texture and anisotropy. These findings provide insight into how precise magnetic responses can be designed using compositionally complex materials that may find application in next-generation magnetic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Modifying magnetic properties of MnBi with carbon: an experimental and theoretical study

MnBi and MnBi-based materials have been investigated as prospective rare-earth-free permanent magnets with moderate energy product. One of the main issues with MnBi synthesis is the presence of residual Bi in the sample which reduces the net magnetization. Here, we have found that MnBi synthesized in the presence of carbon substantially reduces the amount of residual Bi, improving its saturation magnetization. We have synthesized Mn 55 Bi 45 and Mn 55 Bi 45 C x samples using arc melting and high-vacuum annealing. The room temperature x-ray diffraction patterns indicate that both Mn 55 Bi 45 and Mn 55 Bi 45 C x crystallize in the hexagonal NiAs-type structure. The Rietveld analysis of the x-ray patterns shows that the amount of residual Bi reduces from 16 wt.% for Mn 55 Bi 45 to 5 wt.% for Mn 55 Bi 45 C x . The high-field (3 T) magnetizations measured at room temperature are 61 emu g –1 and 66 emu g –1 for Mn 55 Bi 45 and Mn 55 Bi 45 C x , respectively. To understand the role of C in enhancing the magnetization of MnBi, we carried out the first-principles calculations of both stoichiometric and nonstoichiometric MnBi alloys, which suggests that the increase of magnetization in Mn 55 Bi 45 C x may be due to the coating of MnBi grains with C.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1984

Off-axis tensile properties and fracture in a unidirectional graphite/polyimide composite (Celion 6000/PMR 15)

Tensile properties of unidirectional Celion 6000 graphite/PMR 15 polyimide composites prepared by hot molding and cold molding processes were measured at room temperature and 316 C, the upper use temperature of the polyimide resin, at both 45 and 90 deg to the fiber axis. The resulting fractures were characterized by scanning electron microscopy and materialographic techniques. Variation in tensile properties with processing history occurred in the elastic modulus and strain to failure for specimens loaded at 90 deg at 316 C, and in the fracture stress, and hence the in-plane shear stress, for those loaded at 45 deg at room temperature. Significant plastic deformation was observed in the 45 deg orientation at 316 C for material produced by both processing methods. In general, fracture occurred by both failure within the matrix and at the fiber-matrix interface; the degree of interfacial failure increased with temperature. Secondary cracking below the primary fracture surface was also observed.

Harper, J.↗
NASA NTRS1995

Magnetic properties of iron-bearing graphite fibers

Carbon fibers containing ferromagnetically-ordered iron or other transition metals could be used in a variety of lightweight magnetic composites. Intercalation of bulk graphite with CoCl2 or FeCl3, followed by reduction with butyl lithium, did indeed produce magnetic samples; however, the observed room temperature permeabilities (mu) were less than 2 G/Oe. Magnetic data are presented on carbon fibers containing large amounts of elemental iron, which were prepared by a new method. In this method Amoco P-75 fibers were intercalated with Br2 and I2 followed by fluorination, forming CF(0.75). This product was then intercalated with FeCl3. Subsequent heat treatments in oxidizing and reducing atmospheres converted most of the iron to the pure alpha phase. Room temperature permeabilities as large as 40 G/Oe are observed.

Ferrante, R.↗
DOE OSTI2021

Crystal Structure and Preparation of Li7La3Zr2O12 (LLZO) Solid-State Electrolyte and Doping Impacts on the Conductivity: An Overview

As an essential part of solid-state lithium-ion batteries, solid electrolytes are receiving increasing interest. Among all solid electrolytes, garnet-type Li7La3Zr2O12 (LLZO) has proven to be one of the most promising electrolytes because of its high ionic conductivity at room temperature, low activation energy, good chemical and electrochemical stability, and wide potential window. Since the first report of LLZO, extensive research has been done in both experimental investigations and theoretical simulations aiming to improve its performance and make LLZO a feasible solid electrolyte. These include developing different methods for the synthesis of LLZO, using different crucibles and different sintering temperatures to stabilize the crystal structure, and adopting different methods of cation doping to achieve more stable LLZO with a higher ionic conductivity and lower activation energy. It also includes intensive efforts made to reveal the mechanism of Li ion movement and understand its determination of the ionic conductivity of the material through molecular dynamic simulations. Nonetheless, more insightful study is expected in order to obtain LLZO with a higher ionic conductivity at room temperature and further improve chemical and electrochemical stability, while optimal multiple doping is thought to be a feasible and promising route. This review summarizes recent progress in the investigations of crystal structure and preparation of LLZO, and the impacts of doping on the lithium ionic conductivity of LLZO.

Raju, Md Mozammal (ORCID:0000000319040523)↗
DOE OSTI2022

In-situ TEM study of Kr ion irradiation tolerance of SiFeOC nanocomposite

Here, in this work, ion irradiation of polymer derived SiFeOC nanocomposite was carried out using 1.2 MeV Kr ions at room temperature and 600°C. The starting composite was composed of Fe 3 Si, SiC, SiOC, SiO 2 , and graphitic C. In-situ TEM investigations show uniform distribution of nano-crystalline Fe 3 Si and SiC phases in the amorphous SiOC matrix. During ion irradiation, the SiOC bulk microstructure and interfaces between Fe 3 Si or SiC crystallites and the SiOC matrix remain defect-free and demonstrate outstanding ion irradiation resistance. At room temperature, the crystalline domains are stable up to 2 dpa. At 600°C, Fe 3 Si crystallites are more stable than SiC; SiC crystallites are stable up to 4 dpa while the Fe 3 Si crystallites are stable up to 10 dpa. These crystallites also coalescence and amorphize simultaneously during ion irradiation. The exceptional tolerance to defect formation and irradiation of the SiFeOC nanocomposite provides important guidance to developing irradiation resistant fuels for advanced gas cooled reactors.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A family of dual-anion-based sodium superionic conductors for all-solid-state sodium-ion batteries

The sodium (Na) superionic conductor is a key component that could revolutionize the energy density and safety of conventional Na-ion batteries. However, existing Na superionic conductors are primarily based on a single-anion framework, each presenting inherent advantages and disadvantages. Here we introduce a family of amorphous Na-ion conductors (Na 2 O 2 –MCl y , M = Hf, Zr and Ta) based on the dual-anion framework of oxychloride. Benefiting from a dual-anion chemistry and with the resulting distinctive structures, Na 2 O 2 –MCl y electrolytes exhibit room-temperature ionic conductivities up to 2.0 mS cm -1 , wide electrochemical stability windows and desirable mechanical properties. All-solid-state Na-ion batteries incorporating amorphous Na 2 O 2 –HfCl 4 electrolyte and a Na 0.85 Mn 0.5 Ni 0.4 Fe 0.1 O 2 cathode exhibit a superior rate capability and long-term cycle stability, with 78% capacity retention after 700 cycles under 0.2 C (1C = 120 mA g -1 ) at room temperature. The discoveries in this work could trigger a new wave of enthusiasm for exploring new superionic conductors beyond those based on a single-anion framework.

25 ENERGY STORAGE↗
DOE OSTI2024

Time-resolved magneto-optical effects in the altermagnet candidate MnTe

α -MnTe is an antiferromagnetic semiconductor with above room temperature T N = 310 K, which is promising for spintronic applications. Recently, it was reported to be an altermagnet, containing bands with momentum-dependent spin splitting; time-resolved experimental probes of MnTe are, therefore, important both for understanding novel magnetic properties and potential device applications. Here, we investigate ultrafast spin dynamics in epitaxial MnTe(001)/InP(111) thin films using pump-probe magneto-optical measurements in the Kerr configuration. At room temperature, we observe an oscillation mode at 55 GHz that does not appear at zero magnetic field. Combining field and polarization dependence, we identify this mode as a magnon, likely originating from inverse stimulated Raman scattering. Magnetic field-dependent oscillations persist up to at least 335 K, which could reflect coupling to known short-range magnetic order in MnTe above T N . Additionally, we observe two optical phonons at 3.6 and 4.2 THz, which broaden and redshift with increasing temperature.

Gray, Isaiah↗
NASA NTRS1990

Catalysts for ultrahigh current density oxygen cathodes for space fuel cell applications

The objective of this research was to identify promising electrocatalyst/support systems for the oxygen cathode in alkaline fuel cells operating at relatively high temperatures, O2 pressures and current densities. A number of materials were prepared, including Pb-Ru and Pb-Ir pyrochlores, RuO2 and Pt-doped RuO2, and lithiated NiO. Several of these were prepared using techniques that had not been previously used to prepare them. Particularly interesting is the use of the alkaline solution technique to prepare the Pt-doped Pb-Ru pyrochlore in high area form. Well-crystallized Pb(2)Ru(2)O(7-y) was used to fabricate high performance O2 cathodes with relatively good stability in room temperature KOH. This material was also found to be stable over a useful potential range at approximately 140 C in concentrated KOH. Other pyrochlores were found to be either unstable (amorphous samples) or the fabrication of the gas-fed electrodes could not be fully optimized during this project period. Future work may be directed at this problem. High area platinum supported on conductive metal oxide supports produced mixed results: small improvements in O2 reduction performance for Pb(2)Ru(2)O(7-y) but a large improvement for Li-doped NiO at room temperature. Nearly reversible behavior was observed for the O2/OH couple for Li-doped NiO at approximately 200 C.

Tryk, D.↗
DOE OSTI2020

Multi-scale experimental study of creep-fatigue failure initiation in a 709 Stainless Steel alloy using high resolution digital image correlation. Final report

This report discusses the efforts made towards the multi-scale study of the creep-fatigue response of stainless steel 709. Multiple experimental techniques, including digital image correlation (DIC) and electron backscatter diffraction (EBSD), were used in assessing the evolution of damage accumulation during fatigue, creep-fatigue, and thermomechanical fatigue of alloy 709. The role of microstructural features, hold times, temperature, and loading profiles were quantified and the interchangeability of temperature and time was investigated. Finally, a thermomechanical fatigue model was shown to predict well the failure of samples with varying loading profiles. Results indicate that strain accumulation in 709 steel happens primarily near grain boundaries (GBs) with the strains around GBs being inversely proportional to their measured residual burgers vector. Furthermore, hot-spots for strain accumulation were shown to be the locations of eventual microcrack nucleation. The introduction of hold times to the periodic loading cycle increases the damage accumulation rate and thus shortens the fatigue life of samples–this was true for both room temperature and high temperature. Thermomechanical cycling was shown to have little effect on the end life of samples, with the damage accumulation rate for in-phase and out-of-phase cycling being similar to isothermal fatigue. The interchangeability of time and temperature was shown to be possible within the studied load, time, and temperature ranges, since deformation mechanisms driving strain accumulation did not change with temperature (up to 650°C). The Neu-Sehitoglu thermomechanical fatigue model, with constants obtained from the literature and in part from our experimental results, was applied to predict failure of isothermal creep-fatigue samples. The main objectives of this work were to:(a) Perform high-resolution digital image correlation measurements (HiDIC) for alloy 709; (b) Quantify and assess damage accumulation at the microstructure under fatigue, TMF, and creep-fatigue conditions of 709; (c) Study of the role of hold times, i.e., adding a creep component, to: Room temperature cycling, High temperature cycling, Failure; (d) Study the mechanisms of thermomechanical fatigue in this alloy; (e) Investigate the existence of a time-temperature interchangeability criterion to aid in accelerated creep-fatigue testing; (f) Establish the validity of a combined creep-fatigue model for life prediction for 709. This report is structured with each subsequent section detailing the efforts, results, and conclusions related to each of the objectives described, mostly in chronological order.

36 MATERIALS SCIENCE↗
NASA NTRS1998

A Specimen Size Effect on the Fatigue Crack Growth Rate Threshold of IN 718

Fatigue crack growth rate (FCGR) tests were conducted on IN 718 in the solution annealed and aged condition at room temperature in accordance with E647-87. As part of each test, the FCGR threshold was measured using the decreasing Delta K method. A new heat of material was being tested and some of this material was sent to a different laboratory which wanted to use a specimen with a 127 mm width. Threshold data previously had been established on specimens with a width of 50.8 mm. As a check of the laboratory, tests were conducted at room temperature and R equal to 0.1 for comparison with the earlier data. The results were a threshold significantly higher than previously observed. Interchanging of specimen sizes and laboratories showed that the results were not due to a heat-to-heat or lab-to-lab variation. The results to be presented here are those obtained at the original laboratory. Growth rates were measured using the electric potential drop technique at R values of 0.1, 0.7, and 0.9. Compact tension specimen sizes with planer dimensions of 25.4 mm, 50.8 mm, and 127 mm were used. Crack growth rates at threshold were generally below 2.5 X 10(exp -8) mm / cycle. Closure measurements were made on some of the specimens by a manual procedure using a clip gage. When the crack growth rate data for the specimens tested at R equal to 0.1 were plotted as a function of applied Delta K, the thresholds varied with specimen width. The larger the width, the higher the threshold. The thresholds varied from 6.5 MPa-m(exp 1/2) for the 25.4 mm specimen to 15.4 MPa-m(exp 1/2) for the 127 mm specimen. At R equal to 0.7, the 25.4 mm and 50.8 mm specimens had essentially the same threshold, about 2.9 MPa-m(exp 1/2)while the 127 mm specimen had a threshold of 4.5 MPa-m(exp 1/2). When plotted as a function of effective Delta K, the R equal to 0.1 data are essentially normalized. Various aspects of the test procedure will be discussed as well as the results of analysis of the data using some different closure models.

Garr, K. R.↗
NASA NTRS2006

Comparison of the Effects of Tool Geometry for Friction Stir Welding Thin Sheet Aluminum Alloys for Aerospace Applications

In this presentation, the results of a recent study on the effect of pin tool design for friction stir welding thin sheets (0.040") of aluminum alloys 2024 and 7075 are provided. The objective of this study was to investigate and document the effect of tool shoulder and pin diameter, as well as the presence of pin flutes, on the resultant microstructure and mechanical properties at both room temperature and cryogenic temperature. Specifically, the comparison between three tools will include: FSW process load analysis (tool forces required to fabricate the welds), Static Mechanical Properties (ultimate tensile strength, yield strength, and elongation), and Process window documenting the range of parameters that can be used with the three pin tools investigated. All samples were naturally aged for a period greater than 10 days. Prior research has shown 7075 may require post weld heat treatment. Therefore, an additional pair of room temperature and cryogenic temperature samples was post-weld aged to the 7075-T7 condition prior to mechanical testing.

Merry, Josh↗
NASA NTRS2019

Vapor Growth of Indium Monoiodide

Indium (I) iodide, InI, is part of a group of heavy metal iodides that can be used as room temperature radiation detectors. Other examples are HgI2, PbI2, BiI3, or TlPbI3. InI has several advantages, such as low toxicity, no solid phase transition (such as in HgI2), and no tendency to form polytypes (PbI2, BiI3 ). All binary iodides have layered structures and are quite soft, but InI is also the mechanically most stable compound of the binary compounds. Table 1 shows the main properties of InI in comparison with the other iodides and the most common room temperature radiation detector material, (Cd, Zn)Te. InI is typically grown by the unseeded Bridgman method using a nucleation tip, but Czochralski (CZ) growth has also been demonstrated. The resulting crystals have been used successfully for radiation detection, but both resistivity and mobility are usually well below theoretically predicted values. Physical vapor transport (PVT), although much slower than melt growth, is an alternative method and has been used to grow e.g. HgI2, PbI2, BiI3, CdTe. PVT growth should eliminate or reduce inclusions and impurities since it is based on sublimation, reduce intrinsic defects due to the lower growth temperature, and reduce dislocation densities due to reduced thermal and mechanical stress. As an example, PVT-grown CdTe showed a much improved structural quality compared to Bridgman- or THM-grown material.

Cröll, Arne↗
DOE OSTI2024

Trailblazing Kr/Xe Separation: The Birth of the First Kr-Selective Material

Efficient separation of Kr from Kr/Xe mixtures is pivotal in nuclear waste management and dark matter research. Thus far, scientists have encountered a formidable challenge: the absence of a material with the ability to selectively adsorb Kr over Xe at room temperature. This study presents a groundbreaking transformation of the renowned metal–organic framework (MOF) CuBTC, previously acknowledged for its Xe adsorption affinity, into an unparalleled Kr-selective adsorbent. This achievement stems from an innovative densification approach involving systematic compression of the MOF, where the crystal size, interparticle interaction, defects, and evacuation conditions are synergistically modulated. The resultant densified CuBTC phase exhibits exceptional mechanical resilience, radiation tolerance, and notably an unprecedented selectivity for Kr over Xe at room temperature. Simulation and experimental kinetic diffusion studies confirm reduced gas diffusion in the densified MOF, attributed to its small pore window and minimal interparticle voids. The lighter Kr element demonstrates facile surface passage and higher diffusivity within the material, while the heavier Xe encounters increased difficulty entering the material and lower diffusivity. This Kr-selective MOF not only represents a significant breakthrough in Kr separation but also demonstrates remarkable processability and scalability to kilogram levels. Furthermore, the findings presented herein underscore the transformative potential of engineered MOFs in addressing complex challenges, heralding a new era of Kr separation technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tank 48H Tetraphenylborate Mitigation: Simulant Studies using Sodium Permanganate

Tank 48H currently holds legacy material containing organic tetraphenylborate (TPB) compounds from the operation of the In-Tank Precipitation (ITP) process. TPB was added during the ITP process to precipitate the otherwise soluble cesium as insoluble cesium TPB (CsTPB), but excessive benzene generation from TPB degradation curtailed this treatment method. The contents of Tank 48H, which include approximately 26.000 kg of potassium TPB (KTPB) and trace CsTPB, are not compatible with the waste treatment facilities at the Savannah River Site (SRS) since the organic content and the associated flammability issues pose a challenge to the salt processing and sludge processing facilities within the liquid waste system. An in-tank process to remove (or decompose) TPB safely would be of great value. Previous testing at Savannah River National Laboratory (SRNL) demonstrated the destruction of glycolate via chemical oxidation using sodium permanganate with simulated and radioactive waste. Scoping tests were performed to study the destruction of TPB to determine if the contents of Tank 48H would be amenable to the same type of destruction. Partial destruction of TPB was observed in Tank 48H simulants under mild conditions (e g., pH 11, room temperature) with no definitive indication of benzene generation. To build upon the success of the scoping tests, an additional study was requested to provide a better understanding of the underlying chemistry for Tank 48H content destruction using sodium permanganate. Three experiments were performed with Tank 48H simulants at 40 °C to determine the efficacy of using sodium permanganate for TPB destruction. Three starting pH values were selected: 1) pH 11 for comparison with the previous work at room temperature, 2) pH 10 as the minimum pH recommended by the Corrosion Control Program (CCP) for in-tank processing, and 3) pH 8 to determine the effectiveness of TPB destruction at near neutral pH. While below the allowable pH for the CCP, the experiment at pH 8 was performed to study the TPB-Permanganate reaction under more extreme conditions and further verify the potential for out-of-tank processing.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
NASA NTRS2009

Architectural Effects on Impact Resistance of Uncoated MI SiC/SiC Composites

Impact tests were conducted on uncoated 2D and 2.5D MI SiC/SiC composite specimens at room temperature and 1316 C in air. The specimens were analyzed before and after impact using optical microscopy, pulsed thermography (PT) and computed tomography (CT). Preliminary results indicate the following. Both 2-D and 2.5D composites show increase in surface and volumetric damages with increasing impact velocity. However, 2-D composites are prone to delamination cracks. In both 2D and 2.5D composites, the magnitude of impact damage at a fixed impact velocity is slightly greater at room temperature than at 1315 C. At a fixed projectile velocity and test temperature, the depth of penetration of the projectile into the substrate is significantly lower in 2.5D composites than in 2D composites. Fiber architecture plays a significant role controlling impact damage in MI SiC/SiC composites.

Bhatt, R. T.↗