Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “foaming”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Development of a high fidelity model of the CROCUS experimental reactor

Measurements of scalar flux distributions with fine spatial and energy resolutions are needed to remedy one of the validation shortcomings of the novel neutronics full core solvers, such as MPACT and nTRACER. While a very detailed resolution of the flux can be calculated with such codes, only a limited experimental data set is available to check their accuracy. Such type of measurements are on-going at the zero power reactor CROCUS, operated at the Laboratory for Reactor Physics and System Behaviours of the EPFL, thanks to the development of advanced miniature neutron detection systems. This kind of experimental data would provide the community with a suitable benchmark for the validation of high fidelity neutronics solvers. In parallel, a multi-physics solver for steady-state and transient analysis of nuclear reactors, named GeN-Foam, has been developed. Based on the finite-volume OpenFOAM library, GeN-Foam provides us with enough flexibility to analyze non-conventional reactor geometries such as that of CROCUS. While CROCUS heterogeneities cannot be modeled by MPACT and nTRACER for the moment, GeN-Foam offers a unique opportunity to build a high fidelity model which mimics these codes' method to reach sub-pin simulation resolution. This document aims at describing the work achieved to get from the existing GeN-Foam model of the CROCUS reactor based on a structured mesh and using the neutron diffusion, the first high-fidelity model using discrete ordinates method as an approximation to neutron transport and an unstructured mesh for inter lattice water gap description and sub-pin heterogeneous modeling. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2018

Efficient hydrogenation of benzaldoximes and Schiff bases on ceramic high-porosity palladium catalysts

An efficient catalytic method for the synthesis of benzyl- and dibenzylamines by hydrogenating oximes and Schiffbases was developed on palladium supported high-porosity foamed ceramic block catalyst. The multiple regeneration ability of the foamed ceramic block catalyst can significantly decrease the Pd consumption as compared to the use of the conventional 10%Pd/C catalyst. Owing to a high hardness of the foamed ceramic catalyst, the reaction mixture can rapidly be removed from the reactor without using filtering devices. The structures produced by the reaction are fragments of biologically active and natural molecules. Antiproliferative properties of dibenzylamines revealed on the sea urchin embryo model suggest that these compounds can be considered as promising agents for the design of new anticancer drugs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Carbonaceous Material Properties and Their Interactions with Slag During Electric Arc Furnace Steelmaking

The state of the interface between slag and carbon determines the slag foaming behavior and thus the effectiveness of carbon in electric arc furnace (EAF) steelmaking. This paper explores the interaction between synthetic slag and carbonaceous materials derived from various sources, including bio-char produced by two different technologies, graphite, coke, and char from tire pyrolysis. Different interfacial phenomena were found between slag and the carbonaceous materials examined. The interactions between bio-char and slag are found to be poor in comparison with other carbonaceous materials. Carbonaceous materials were characterized in terms of their chemical composition and the results obtained suggested that interfacial phenomena were not dominated by ash in the carbonaceous material. The effects of carbon crystalline structure on interaction with slag were evaluated by Raman spectroscopy and X-ray diffraction. Surface properties of the samples were evaluated using scanning electron microscopy, and surface morphology was identified as the principal factor affecting the interaction of slag on carbonaceous particles. The smooth surface of bio-char results in reduced slag foaming. This finding forms the basis for future research on the production of bio-char to be used as a slag foaming agent in EAF steelmaking.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Thermomechanical Properties of Polypropylene-Based Lightweight Composites Modeled on the Mesoscale

A waste-based particle polymer composite (WPPCs) made of foam glass and polypropylene was developed as a low-cost construction material. Thermomechanical properties of the composite, including creep properties of WPPC and polypropylene binder, were examined. By adding a relatively small amount of polypropylene to foam glass (about 2:8 in volume parts), the maximum bearing capacity at room temperature of the composite increased from 1.9 (pure foam glass) to 15 MPa. A significant creep strain accumulated during compressive loading of WPPC (5 MPa) in the first 2000 s at elevated temperatures (40, 60 °C). In the study, Kafka’s mesomechanical model was used to simulate creep strain changes in time for various temperatures. The applicability of Kafka’s mesomechanical model for simulating creep properties of the studied composite material was demonstrated.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Improving the energy efficiency of a refrigerator-freezer through the use of a novel cabinet/door liner based on polylactide biopolymer

This paper presents the energy savings potential of a newly developed liner applied on the foam insulation used in refrigerator and freezer cabinets, compared with using a more commonly used liner made from high-impact polystyrene. The new polylactic acid polymer liner is made from renewable feedstock such as carbon found in plant sugars. The energy use over the life of refrigerator and freezer is calculated using the Energy-Efficient Refrigerator Analysis program developed by the United States Department of Energy to estimate the energy savings potential of various technology option upgrades (cabinet and refrigeration system) for rulemaking purposes. The simulation results show that energy savings from implementing the Ingeo liner range from 818 to 1395tkWh (7.3–12.5% of total energy use) over a 15-year period. In addition to the energy savings, the slower increase in the thermal conductivity of the insulation could allow the compressor to run fewer hours per year compared with a case in which the foam thermal conductivity increases rapidly. This change could increase the life of the compressor and the refrigerators and freezers. As a result, this study does not attempt to quantify the impact of slower foam aging on the compressor life.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2018

Photocatalytic degradation of cooking fume on a TiO2-coated carbon nanotubes composite filter

Highlights: • The TiO{sub 2}-coated carbon nanotube composite filter was fabricated for treating cooking fume particles. • MWCNTs formed a network-like structure surface layer of composite filter. • The composite filter showed high surface area. • The composite filter was tested in oleic acid decomposition reaction. • Parallel reaction mechanism was attempted to describe oleic acid degradation. A TiO{sub 2}/MWCNTs/Al{sub 2}O{sub 3}/NF (TiO{sub 2} nanoparticles/multi-walled carbon nanotubes /Al{sub 2}O{sub 3}-modified nickel foams) composite filter was prepared through grown of MWCNTs upon Al{sub 2}O{sub 3}-modified nickel foams using chemical vapor deposition (CVD) method and then coated TiO{sub 2} nanoparticles onto MWCNTs using dip-coating method. The MWCNTs forms a network-like structure on the surface layer of composite filter. The BET surface area of TiO{sub 2}/MWCNTs/Al{sub 2}O{sub 3}/NF composite filter is more than 375 times higher than that of the pristine nickel foam. The degradation performance of oil particles was evaluated. Under optimized reaction conditions, 90% of the oleic acid on the filter was decomposed after 25 h. In addition, the effect of reaction temperature and light intensity were studied. Increased reaction temperature and light intensity were found to significantly improve the degradation rate and restrain the formation of refractory product. Furthermore, a parallel reaction kinetic model was adopted for degradation of oleic acid on the composite filter. The composite filter can reduces the accumulation of oil particles on the filter and the energy consumption of the filter. This approach proposes a new way to treat the cooking fume emission at residential building roofs.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2014

Three-dimensional interconnected nickel phosphide networks with hollow microstructures and desulfurization performance

Graphical abstract: Three-dimensional interconnected nickel phosphide networks with hollow microstructures and desulfurization performance. - Highlights: • Three-dimensional Ni{sub 2}P has been prepared using foam nickel as a template. • The microstructures interconnected and formed sponge-like porous networks. • Three-dimensional Ni{sub 2}P shows superior hydrodesulfurization activity. - Abstract: Three-dimensional microstructured nickel phosphide (Ni{sub 2}P) was fabricated by the reaction between foam nickel (Ni) and phosphorus red. The as-prepared Ni{sub 2}P samples, as interconnected networks, maintained the original mesh structure of foamed nickel. The crystal structure and morphology of the as-synthesized Ni{sub 2}P were characterized by X-ray diffraction, scanning electron microscopy, automatic mercury porosimetry and X-ray photoelectron spectroscopy. The SEM study showed adjacent hollow branches were mutually interconnected to form sponge-like networks. The investigation on pore structure provided detailed information for the hollow microstructures. The growth mechanism for the three-dimensionally structured Ni{sub 2}P was postulated and discussed in detail. To investigate its catalytic properties, SiO{sub 2} supported three-dimensional Ni{sub 2}P was prepared successfully and evaluated for the hydrodesulfurization (HDS) of dibenzothiophene (DBT). DBT molecules were mostly hydrogenated and then desulfurized by Ni{sub 2}P/SiO{sub 2}.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Low-Temperature Processing of Pyrolysis Bio-Oil for Sustainable Biographite Production

Catalytic graphitization of pyrolysis bio-oil with iron (Fe) can produce an anode material for lithium-ion batteries (LIBs) at a moderate temperature. The key challenge to scaling up the process is foaming, which occurs due to the oxidation of Fe by the organic acids present in bio-oil. This study explored five different pathways to control foaming in bio-oil upon Fe addition, including (i) defoamers use, (ii) use of iron oxide (Fe2O3) as graphitization catalyst, (iii) pH adjustment of bio-oil, (iv) bio-oil coking (300-500 degrees C), and (v) low-temperature pretreatment of bio-oil (150-200 degrees C). The low-temperature pretreatment successfully avoided foaming by removing the volatile acids in bio-oil. The bio-oil was solidified and powdered for even mixing with the Fe catalyst. The biographite catalytically prepared at 1500 degrees C following this pathway demonstrated nearly theoretical specific gravimetric capacity (~370 mAh/g), high initial Coulombic efficiency (90.03%), and minimal capacity fading after 50 cycles in LIB half-cells. The low-temperature pretreatment pathway also addressed the viscosity, swelling, and aging issues associated with bio-oil processing and will make scale-up endeavors more attainable.

09 BIOMASS FUELS↗
DOE OSTI2024

Tailoring Pore Architecture and Heteroatom Functionality of Polymeric Waste-Derived Nanoporous Carbon for CO 2 Capture Applications

This study proposes upcycling polymeric waste, i.e., waste floral foam, into high-performance nanoporous carbon that efficiently captures CO 2 . This paper presents strategies for improving the properties of nanoporous carbon, which aid in a superior CO 2 capture performance. Initially, pristine nanoporous carbon was produced from waste floral foam using various KOH impregnation ratios. The nanoporous carbon with a 1:2 (waste floral foam:KOH) ratio exhibiting optimal CO 2 capture capability was further advanced through single and dual atom doping. The doping of N and codoping of N,S atoms into the nanoporous carbon altered its textural and surface chemical properties, making them efficient for CO 2 capture. Comparative CO 2 capture studies of pristine nanoporous carbon (NC-x), N-doped nanoporous carbon (N-NC2), and N,S-codoped nanoporous carbon (N,S-NC2) demonstrate the superiority of N-doping. N-doped nanoporous carbon exhibited the largest ultramicroporosity (0.3100 cm3/g, 63.43%) and highest heteroatom content (34.94 atomic %), contributing to its enhanced CO 2 capture capability (4.54 mmol/g). Finally, implementing the “waste-to-depollution” approach, this research lays the groundwork for producing low-cost, environmentally friendly nanoporous carbon with remarkable CO 2 capture attributes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Green Catalysts for Reprocessing Thermoset Polyurethanes

Polyurethane (PU) thermosets are usually landfilled at the end of their service lifetimes and cannot be recycled through conventional means. Although dibutyltin dilaurate (DBTDL) is an effective catalyst for reprocessing PU thermosets, organotins are immunotoxic and teratogenic, which is concerning for catalysts embedded within covalent adaptable networks (CANs). Here, we identify Zr(acac) 4 and Zr(tmhd) 4 as catalysts to reprocess PU CANs more sustainably. Thermoset PU foams containing Zr-based catalysts exhibit characteristic stress relaxation times between 6 and 200 s, similar or faster than DBTDL. These catalysts are capable of reprocessing a PU foam for four or five cycles. Dynamic mechanical thermal analysis indicates that zirconium-based catalysts preserve glass transition temperature and crosslink density between cycles and are promising catalysts for bulk reprocessing of thermoset PUs. Here, a solvent-free reprocessing method was developed by co-milling the PU foam and the Zr catalyst. Ultimately, these reprocessing methods using Zr-based catalysts will impart greater sustainability and circularity to PU plastics.

Catalysts↗
DOE OSTI2014

Terahertz inline wall thickness monitoring system for plastic pipe extrusion

Conventional and commercially available inline wall thickness monitoring systems for pipe extrusion are usually based on ultrasonic or x-ray technology. Disadvantages of ultrasonic systems are the usual need of water as a coupling media and the high damping in thick walled or foamed pipes. For x-ray systems special safety requirements have to be taken into account because of the ionizing radiation. The terahertz (THz) technology offers a novel approach to solve these problems. THz waves have many properties which are suitable for the non-destructive testing of plastics. The absorption of electrical isolators is typically very low and the radiation is non-ionizing in comparison to x-rays. Through the electromagnetic origin of the THz waves they can be used for contact free measurements. Foams show a much lower absorption in contrast to acoustic waves. The developed system uses THz pulses which are generated by stimulating photoconductive switches with femtosecond laser pulses. The time of flight of THz pulses can be determined with a resolution in the magnitude of several ten femtoseconds. Hence the thickness of an object like plastic pipes can be determined with a high accuracy by measuring the time delay between two reflections on materials interfaces e.g. at the pipe's inner and outer surface, similar to the ultrasonic technique. Knowing the refractive index of the sample the absolute layer thickness from the transit time difference can be calculated easily. This method in principle also allows the measurement of multilayer systems and the characterization of foamed pipes.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Development of Stochastic Voronoi Lattice Structures via Two-Photon Polymerization

Low-density polymer foams of varying sizes, shapes, and densities are of specific interest to the inertial confinement fusion (ICF) program and related high-energy density plasma physics research. Historically, these foams are comprised of polystyrene or other low atomic number materials and have densities in the 30 to 300 mg/cm 3 range. However, at the lower end of this density range, these traditional polymer foams become fragile and difficult to cast and machine into the geometries needed. Recently, the need by experimentalists for materials with densities below 30 mg/cm 3 has increased. To address these needs, we are developing three-dimensional (3-D) printing techniques to create high-precision, low-density, and repeatable complex lattice structures. Using two-photon polymerization 3-D printing, we recently developed the first 5 mg/cm3 low-density lattice structure having an annular hemispherical shape. These microscale to mesoscale structures were modeled and designed using the nTopology software, specifically utilizing the "Voronoi volume lattice" and "random points in body" option blocks. All printing operations were performed using the Nanoscribe Photonic Professional GT instrument. Characterization of these 3-D structures was conducted using various microscopic and X-ray tomographic imaging techniques. Furthermore, overall printed part sizes ranged from 1 to 5 mm in diameter and were composed of lattice ligaments having thicknesses in the 3- to 5-µm range. These structures have been incorporated into ICF targets recently shot on both the University of Rochester’s Laboratory of Laser Energetics Omega laser and the National Ignition Facility.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2014

Stand-Off Furring in Deep Energy Retrofits: Syracuse, New York (Fact Sheet)

IBACOS, in collaboration with GreenHomes America, was contracted by the New York State Energy Research and Development Authority to research exterior wall insulation solutions. This research investigated cost-effective deep energy retrofit (DER) solutions for improving the building shell exterior while achieving a cost-reduction goal, including reduced labor costs to reach a 50/50 split between material and labor. The strategies included exterior wall insulation plus energy upgrades as needed in the attic, mechanical and ventilation systems, and basement band joist, walls, and floors. The work can be integrated with other home improvements such as siding or window replacement. This strategy minimizes physical connections to existing wall studs, encapsulates existing siding materials (including lead paint) with spray foam, and creates a vented rain screen assembly to promote drying. GreenHomes America applied construction details created by IBACOS to a test home. 2x4 framing members were attached to the wall at band joists and top plates using 'L' clips, with spray foam insulating the wall after framing was installed. Windows were installed simultaneously with the framing, including extension jambs. The use of clips in specific areas provided the best strength potential, and 'picture framing' the spray foam held the 2x4s in place. Short-term testing was performed at this house, with monitoring equipment installed for long-term testing. Testing measurements will be provided in a later report, as well as utility impact (before and after), costs (labor and materials), construction time, standard specifications, and analysis for the exterior wall insulation strategy.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2014

Excavationless Exterior Foundation Insulation Field Study

Building science research supports installing exterior (soil side) foundation insulation as the optimal method to enhance the hygrothermal performance of new homes. With exterior foundation insulation, water management strategies are maximized while insulating the basement space and ensuring a more even temperature at the foundation wall. However, such an approach can be very costly and disruptive when applied to an existing home, requiring deep excavation around the entire house. The NorthernSTAR Building America Partnership team implemented an innovative, minimally invasive foundation insulation upgrade technique on an existing home. The approach consisted of using hydrovac excavation technology combined with a liquid insulating foam. The team was able to excavate a continuous 4" wide by 4' to 5' deep trench around the entire house, 128 linear feet, except for one small part under the stoop that was obstructed with concrete debris. The combination pressure washer and vacuum extraction technology also enabled the elimination of large trenches and soil stockpiles normally produced by backhoe excavation. The resulting trench was filled with liquid insulating foam, which also served as a water-control layer of the assembly. The insulation was brought above grade using a liquid foam/rigid foam hybrid system and terminated at the top of the rim joist. Cost savings over the traditional excavation process ranged from 23% to 50%. The excavationless process could result in even greater savings since replacement of building structures, exterior features, utility meters, and landscaping would be minimal or non-existent in an excavationless process.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2014

Excavationless Exterior Foundation Insulation Field Study

Building science research supports installing exterior (soil side) foundation insulation as the optimal method to enhance the hygrothermal performance of new homes. With exterior foundation insulation, water management strategies are maximized while insulating the basement space and ensuring a more even temperature at the foundation wall. However, such an approach can be very costly and disruptive when applied to an existing home, requiring deep excavation around the entire house. The NorthernSTAR Building America Partnership team implemented an innovative, minimally invasive foundation insulation upgrade technique on an existing home. The approach consisted of using hydrovac excavation technology combined with liquid insulating foam. The team was able to excavate a continuous 4 inches wide by 4 feet to 5 feet deep trench around the entire house, 128 linear feet, except for one small part under the stoop that was obstructed with concrete debris. The combination pressure washer and vacuum extraction technology also enabled the elimination of large trenches and soil stockpiles normally produced by backhoe excavation. The resulting trench was filled with liquid insulating foam, which also served as a water-control layer of the assembly. The insulation was brought above grade using a liquid foam/rigid foam hybrid system and terminated at the top of the rim joist. Cost savings over the traditional excavation process ranged from 23% to 50%. The excavationless process could result in even greater savings since replacement of building structures, exterior features, utility meters, and landscaping would be minimal or non-existent in an excavationless process.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2015

Characterization of DWPF Recycle Condensate Tank Materials (Revision 1)

A Defense Waste Processing Facility (DWPF) Recycle Condensate Tank (RCT) sample was delivered to the Savannah River National Laboratory (SRNL) for characterization with particular interest in the concentration of I-129, U-233, U-235, total U, and total Pu. Since a portion of Salt Batch 8 will contain DWPF recycle materials, the concentration of I-129 is important to understand for salt batch planning purposes. The chemical and physical characterizations are also needed as input to the interpretation of future work aimed at determining the propensity of the RCT material to foam, and methods to remediate any foaming potential. According to DWPF the Tank Farm 2H evaporator has experienced foaming while processing DWPF recycle materials. The characterization work on the RCT samples has been completed and is reported here.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Validation Study of Experimental Insulating and Air-Sealing Technology for Enclosed Roof Cavities

Validation Study of Experimental Insulating and Air-Sealing Technology for Enclosed Roof Cavities, explores a new minimally invasive system known as Pinhole Insulation ® for retroft insulation of cathedral ceilings, flat roofs, dormer roofs, and other enclosed roof cavities. It also explores the validation of the associated equipment, software, and materials used in this application. The Pinhole Insulation process essentially consists of drilling a ¼” hole in the ceiling surface and then injecting closed cell polyurethane foam such that the foam is deposited on the interior surface of the exterior roof sheathing. In a typical cathedral ceiling with R19 batts, the R value will be improved by at least 60% and the cavity will become completely air sealed. The system is quick, minimally invasive and at least an order of magnitude less expensive than alternatives such as removing the ceiling surface and spraying closed cell foam.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗