SEARCH · Engineering Papers

Results for “attack surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

All sources NASA NTRS DOE OSTI

NASA NTRS1989

An Euler analysis of leading-edge vortex flows on a forebody-strake at supersonic speeds

The flowfield, surface pressure, and integrated forces and moments for a fighter-type forebody with sharp leading-edge strakes have been obtained by numerical solution of the Euler equations. The method is found to correctly predict the leading-edge vortices and embedded shocks which arise at higher angles of attack. Results are presented for the effects of crossflow grid density, artificial viscosity, angle of attack, streamwise station, and camber on the flow characteristics.

Rose, O. J.↗

NASA NTRS1991

Laser velocimetry measurements of oscillating airfoil dynamic stall flow field

Ensemble-averaged two-component velocity measurements over an airfoil experiencing oscillatory dynamic stall under compressibility conditions were obtained. The measurements show the formation of a separation bubble over the airfoil that persists till angles of attack close to when the dynamic stall vortex forms and convects. The fluid attains mean velocities as large as 1.6 times the free stream velocity with instantaneous values of 1.8 times the free stream velocity. The airfoil motion induces these large velocities in regions that are far removed from the surface.

Chandrasekhara, M. S.↗

NASA NTRS1996

Navier-Stokes Simulation of the Canard-Wing-Body Longitudinal Dynamic Stability Characteristics

Many modern aircraft are canard-configured for aircraft control and improved aerodynamic performance. Canards can often enhance aircraft cruise performance, maneuverability and agility. For close-coupled canard configurations, the aerodynamic interaction between the canard and wing significantly changes the flow characteristics of the wing. In unsteady flow, such changes in the flow structure and performance of wings can be quite pronounced. Accurate modeling of the unsteady aerodynamics is essential for potential CFD design and analysis of such configurations. A time-accurate numerical simulation is performed to study the unsteady aerodynamic interaction between a canard and wing with emphasis on the effects of the canard on the configuration's dynamic response characteristics. The thin-layer Reynolds-averaged Navier-Stokes Equations with various turbulence models are used in this study. Computations are made on a generic, analytically-defined, close-coupled canard-wing-body configuration which has been the subject of numerous previously published experimental studies during the 1970's to mid-80's. More recently, a series of steady-flow simulations has been performed and published by the author. In the current study, the configuration is given prescribed ramp and oscillatory motions in order to predict characteristics such as the damping-in-pitch and oscillatory longitudinal stability parameters. The current computations are made at high-subsonic and transonic Mach numbers, moderate angles-of- attack from -4 to 20 degrees, and at various pitch rates and reduced frequencies. Comparisons of pressures and integrated force quantities (e.g. lift, drag, pitching moment and selected dynamic parameters) are made with other published computational results and available experimental data. Results showing the unsteady effects of the canard on surface pressures, integrated forces, canard-wing vortex interaction and vortex breakdown will be presented.

Tu, Eugene L.↗

NASA NTRS2008

Aerothermodynamic Testing and Boundary Layer Trip Sizing of the HIFiRE Flight 1 Vehicle

An experimental wind tunnel test was conducted in the NASA Langley Research Center s 20-Inch Mach 6 Air Tunnel in support of the Hypersonic International Flight Research Experimentation Program. The information in this article is focused on the Flight 1 configuration, the first in a series of flight experiments. The article documents experimental measurements made over a Reynolds numbers range of 2.1x10(exp 6)/ft to 5.6x10(exp 6)/ft and angles of attack of -5 to +5 deg on several scaled ceramic heat transfer models of the Flight 1 configuration. Global heat transfer was measured using phosphor thermography and the resulting images and heat transfer distributions were used to infer the state of the boundary layer on the vehicle windside and leeside surfaces. Boundary layer trips were used to force the boundary layer turbulent and the experimental data highlighted in this article were used to size and place the boundary layer trip for the flight vehicle. The required height of the flight boundary layer trip was determined to be 0.079 in and the trip was moved from the design location of 7.87 in to 20.47 in to ensure that augmented heating would not impact the laminar side of the vehicle. Allowable roughness was selected to be 3.2x10(exp -3) in.

Berger, Karen T.↗

NASA NTRSDate not supplied

Experimental Study of Aero-Propulsive Interactions for Electric Ducted Fan Arrays in Multiple Positions on a Wing

The Adaptable Distributed Electric Propulsion Testbed (ADEPT) Wing was tested in the NASA Langley 12-Foot Low-Speed Tunnel for the SUbsonic Single Aft eNgine (SUSAN) Electrofan 25% scale flight research vehicle, which aims to reduce emissions for commercial transport aircraft with electric propulsion technologies. The purpose of the test was to study the aero-propulsive effects across angle of attack and fan speed variations for several propulsor placements and array sizes, and to investigate how DEP can be leveraged for augmented lift and vehicle control. Six electric ducted fan (EDF) array placements were tested by positioning the fans along the leading and trailing edges on the top and bottom surfaces, as well as centered on the chord line in front of and behind the wing. Each fan placement configuration was tested with an array of one, three, and five EDFs to characterize an aero-propulsive extrapolation effect, and the bare wing was tested separately to provide baseline aerodynamic measurements. The results compare the longitudinal forces and moments for each configuration by analyzing the combined aero-propulsive interaction effects, and offer valuable insight into considerations for fan placement along a wing to enable the benefits of DEP integration.

Rose Weinstein↗

NASA NTRS2002

Durability Issues for the Protection of Materials from Atomic Oxygen Attack in Low Earth Orbit

Low Earth orbital atomic oxygen is capable of eroding most polymeric materials typically used on spacecraft. Solar array blankets, thermal control polymers, and carbon fiber matrix composites are readily oxidized to become thinner and less capable of supporting the loads imposed upon them. Protective coatings have been developed that are durable to atomic oxygen to prevent oxidative erosion of the underlying polymers. However, the details of the surface roughness, coating defect density, and coating configuration can play a significant role as to whether or not the coating provides long duration atomic oxygen protection. Identical coatings on different surface roughness surfaces can have drastically different durability results. Examples and analysis of the causes of resultant differences in atomic oxygen protection are presented. Implications based on in-space experiences, ground laboratory testing, and computational modeling indicate that thin film vacuum-deposited aluminum protective coatings offer much less atomic oxygen protection than sputter-deposited silicon dioxide coatings.

Banks, Bruce↗

NASA NTRS1972

Calculation of heat transfer on shuttle type configurations including the effects of variable entropy at boundary layer edge

A relatively simple method is presented for including the effect of variable entropy at the boundary-layer edge in a heat transfer method developed previously. For each inviscid surface streamline an approximate shockwave shape is calculated using a modified form of Maslen's method for inviscid axisymmetric flows. The entropy for the streamline at the edge of the boundary layer is determined by equating the mass flux through the shock wave to that inside the boundary layer. Approximations used in this technique allow the heating rates along each inviscid surface streamline to be calculated independent of the other streamlines. The shock standoff distances computed by the present method are found to compare well with those computed by Maslen's asymmetric method. Heating rates are presented for blunted circular and elliptical cones and a typical space shuttle orbiter at angles of attack. Variable entropy effects are found to increase heating rates downstream of the nose significantly higher than those computed using normal-shock entropy, and turbulent heating rates increased more than laminar rates. Effects of Reynolds number and angles of attack are also shown.

Dejarnette, F. R.↗

NASA NTRS1982

A computer program for wing subsonic aerodynamic performance estimates including attainable thrust and vortex lift effects

Numerical methods incorporated into a computer program to provide estimates of the subsonic aerodynamic performance of twisted and cambered wings of arbitrary planform with attainable thrust and vortex lift considerations are described. The computational system is based on a linearized theory lifting surface solution which provides a spanwise distribution of theoretical leading edge thrust in addition to the surface distribution of perturbation velocities. The approach used relies on a solution by iteration. The method also features a superposition of independent solutions for a cambered and twisted wing and a flat wing of the same planform to provide, at little additional expense, results for a large number of angles of attack or lift coefficients. A previously developed method is employed to assess the portion of the theoretical thrust actually attainable and the portion that is felt as a vortex normal force.

Carlson, H. W.↗

NASA NTRS1986

Measurement of leading edge vortices from a delta wing using a three component laser velocimeter

An investigation of the flow field above a 75-deg swept delta wing at a 20.5-deg angle of attack is described. The experiment was performed in the NASA Langley Basic Aerodynamic Research Tunnel (BART) using an orthogonal three-component laser velocimeter. Preliminary laser velocimeter results show velocity vectors in the cross flow plane at x/c = 0.5, revealing the formation of the primary and secondary vortices over the upper surface of the wing.

Meyers, James F.↗

NASA NTRS1989

A flow visualization and aerodynamic force data evaluation of spanwise blowing on full and half span delta wings

A wind-tunnel investigation has been performed to quantify the effects of a jet on the leading-edge vortices generated by a 70-deg-sweep sharp-edged delta wing at low Reynolds numbers. Efforts were made ot optimize the jet nozzle position with respect to maximum lift increments. Both half-span force-balance testing and half- and full-span flow visualization tests were conducted. Two angles of attack were investigated, 30 and 35 deg, at Reynolds numbers of 150,000 and 200,000. Aerodynamic enhancement, including lift and drag gains of about 20 and 17 percent respectively, were measured. Results indicate an optimum jet nozzle location to be close to the leading edge, tangent to the upper wing surface, and in a direction aligned parallel to the leading edge. Nozzle interference effects, especially near the apex, were not negligible.

Visser, K. D.↗

NASA NTRS1989

Corrosion of cordierite ceramics by sodium sulphate at 1000 C

The corrosion of a sintered cordierite (2MgO-2Al2O3-5SiO2) ceramic by sodium sulphate (Na2SO4) was investigated at 1000 C. Laboratory tests with thin films of Na2SO4/O2 and Na2SO4/1 percent SO2-O2 were performed. In the Na2SO4/O2 case, the cordierite reacted to form NaAlSiO4. After several hours of corrosion, the Na2SO4 appeared to induce surface cracks in the cordierite. In the Na2SO4/1 percent SO2-O2 case, other dissolution reactions occurred. The material was also tested in a burner rig with No. 2 Diesel fuel and 2 ppm sodium. The corrosion process was similar to that observed in the Na2SO4/O2 furnace tests, with more severe attack occurring.

Bianco, Robert↗

NASA NTRS1990

Reactions of SiC with H2/H2O/Ar mixtures at 1300 C

Thermochemical modeling anticipates the existence of three reaction regions for the case of a sintered alpha-SiC with 5 percent H2/H2O/Ar at 1300 C, depending on the initial water vapor or, equivalently, oxygen, content of the gas stream. While a high oxygen content leads to SiC-protecting SiO2 surface film formation and limits consumption of the SiC through passive oxidation, intermediate oxygen contents lead to SiO and CO formation and rapid SiC consumption. In this intermediate region, reaction rates appear to be controlled by H2O gas-phase transport to the sample; reacted microstructures exhibit extensive grain-boundary attack in this region. Very low oxygen content is predicted to selectively remove carbon, with free silicon formation.

Jacobson, Nathan S.↗

NASA NTRS1953

Displacement effect of a three-dimensional boundary layer

A method is described for determining the "displacement surface" of known three-dimensional compressible boundary-layer flow in terms of the mass-flow defects associated with the profiles of the two velocity components parallel to the surface. The result is a generalization of the plane flow concept of displacement thickness introduced in order to describe how a thin boundary layer distorts the outer nonviscous flow. Numerical values are found for the known three-dimensional boundary-layer flow about a cone at a small angle of attack to a supersonic stream.

Moore, Franklin K↗

NASA NTRS2001

Environmental Barrier Coatings for Silicon-Based Ceramics

Silicon-based ceramics, such as SiC fiber-reinforced SiC (SiC/SiC ceramic matrix composites (CMC) and monolithic silicon nitride (Si3N4), are prime candidates for hot section structural components of next generation gas turbine engines. Silicon-based ceramics, however, suffer from rapid surface recession in combustion environments due to volatilization of the silica scale via reaction with water vapor, a major product of combustion. Therefore, application of silicon-based ceramic components in the hot section of advanced gas turbine engines requires development of a reliable method to protect the ceramic from environmental attack. An external environmental barrier coating (EBC) is considered a logical approach to achieve protection and CP long-term stability. The first generation EBC consisted of two layers, mullite (3Al2O3-2SiO2) bond coat and yttria-stabilized zirconia (YSZ, ZrO2-8 Wt.% Y2O3) top coat. Second generation EBCs, with substantially improved performance compared with the first generation EBC, were developed in the NASA High Speed Research-Enabling Propulsion Materials (HSR-EPM) Program. The first generation EBC consisted of two layers, mullite (3Al2O3-2SiO2) bond coat and yttria-stabilized zirconia (YSZ, ZrO2-8 wt.% Y2O3) top coat. Second generation EBCs, with substantially improved performance compared with the first generation EBC, were developed in the NASA High Speed Research-Enabling Propulsion Materials (HSR-EPM) Program (5). They consist of three layers, a silicon first bond coat, a mullite or a mullite + BSAS (BaO(1-x)-SrO(x)-Al2O3-2SiO2) second bond coat, and a BSAS top coat. The EPM EBCs were applied on SiC/SiC CMC combustor liners in three Solar Turbines (San Diego, CA) Centaur 50s gas turbine engines. The combined operation of the three engines has accumulated over 24,000 hours without failure (approximately 1,250 C maximum combustor liner temperature), with the engine in Texaco, Bakersfield, CA, accumulating about 14,000 hours. As the commercialization of Si-based ceramic components in gas turbines is on the horizon, a major emphasis is placed on EBCs for two reasons. First, they are absolute necessity for the protection of Si-based ceramics from water vapor. Second, they can enable a major enhancement in the performance of gas turbines by creating temperature gradients with the incorporation of a low thermal conductivity layer. Thorough understanding of current state-of-the-art EBCs will provide the foundation upon which development of future EBCs will be based. Phase stability and thermal conductivity of EPM EBCs are published elsewhere. This paper will discuss the chemical/environmental durability and silica volatility of EPM EBCs and their impact on the coating's upper temperature limit.

Lee, Kang N.↗

NASA NTRS2009

Stability of Supersonic Boundary Layers on a Cone at an Angle of Attack

The stability and receptivity of three-dimensional supersonic boundary layers over a 7deg sharp tipped straight cone at an angle of attack of 4.2deg is numerically investigated at a free stream Mach number of 3.5 and at two high Reynolds numbers, 0.25 and 0.50x10(exp 6)/inch. The generation and evolution of stationary crossflow vortices are also investigated by performing simulations with three-dimensional roughness elements located on the surface of the cone. The flow fields with and without the roughness elements are obtained by solving the full Navier-Stokes equations in cylindrical coordinates using the fifth-order accurate weighted essentially non-oscillatory (WENO) scheme for spatial discretization and using the third-order total-variation-diminishing (TVD) Runge-Kutta scheme for temporal integration. Stability computations reveal that the azimuthal wavenumbers are in the range of m approx. 25-50 for the most amplified traveling disturbances and in the range of m approx. 40-70 for the stationary disturbances. The N-Factor computations predicted that transition would occur further forward in the middle of the cone compared to the transition fronts near the windward and the leeward planes. The simulations revealed that the crossflow vortices originating from the nose region propagate towards the leeward plane. No perturbations were observed in the lower part of the cone.

Balakumar, Ponnampalam↗

NASA NTRS1980

Optimum subsonic, high-angle-of-attack nacelles

Many proposed advanced aircraft - but especially tilt-nacelle, subsonic-cruise, V/STOL aircraft - require nacelles that operate over a wide range of aerodynamic conditions. The optimum design of such nacelles and their inlets is described, including how the inlet low-speed design conditions are selected, the conditions for which the various regions of the inlet are designed, and appropriate criteria of merit. For low-speed operation the optimum internal surface velocity distributions and skin friction distributions are described for three categories of inlets: those without boundary-layer control (BLC), those with BLC, and those with blow-in door slots and retractable slats. Experimental results are presented that show the performance of the various types of inlets. At cruise speed the effect of factors that reduce the nacelle external surface area and the local skin friction is illustrated. These factors are cruise Mach number, inlet throat size, fan-face Mach number, and nacelle contour. The interrelation of these cruise-speed factors with the design requirements for good low-speed performance is discussed. Finally an inlet design without BLC and an optimized inlet design with slots and slats are compared to illustrate the possible reductions in nacelle size.

Luidens, R. W.↗

NASA NTRS1980

Sensor for measuring instantaneous angle of attack of helicopter blades

Systematic investigations were performed on a variety of probes to determine their potential for possible application as sensors attached to helicopter blades to measure both the instantaneous angle of attack as well as the dynamic head during actual flight operations. After some preliminary considerations a sensor of essentially spherical shape, about 30 mm in diameter, was designed. The sensor was provided with three pressure ports, and it housed two pressure transducers required for sensing the prevailing pressures acting outside on the surface. The sensors were subsequently tested in the laboratory under a variety of flow conditions to determine their aerodynamic characteristics. Two series of tests were performed: in the first series the sensor was fixed in space while exposed to steady uniform flow, while in the second series the sensor was made to oscillate, thus simulating the cyclic pitch change of the helicopter blades. While the cyclic pitch frequencies were of about the same magnitude as encountered in flight, the flow velocities during tests fell well below those experienced in a rotating blade. The tests showed that the sensors performed satisfactorily under low subsonic flow conditions with frequencies not exceeding five Hz.

Barna, P. S.↗

NASA NTRS1980

Aerodynamic side-force alleviator means

An apparatus for alleviating high angle of attack side force on slender pointed cylindrical forebodies such as fighter aircraft, missiles and the like is described. A symmetrical pair of helical separation trips was employed to disrupt the leeside vortices normally attained. The symmetrical pair of trips starts at either a common point or at space points on the upper surface of the forebody and extends along separate helical paths along the circumference of the forebody.

Rao, D. M.↗