Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “air conditioning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Tracer gas test in Net-Zero Energy Residential Test Facility

The Net-Zero Energy Residential Test Facility (NZERTF) at NIST was built in 2012 to support the development and adoption of cost-effective net-zero energy designs, technologies, and construction methods. It is two-story, and has four bedrooms, three bathrooms, and an open living room, dining room, and kitchen space. The NZERTF also has a basement and attic, both located within the conditioned space because the thermal and air-moisture barriers encompass the basement walls and attic roof. Transfer grilles link the living spaces to these two zones. The central heating and cooling system includes an air-toair heat pump, which delivers air to the basement, first and second floors. The heat pump has a cooling capacity of 7.6 kW and a heating capacity of 7.8 kW. The indoor unit is in the basement and ductwork runs along the basement ceiling. A balanced heat recovery ventilator (HRV) is installed in the basement and has its own dedicated ductwork. The HRV supplies 47 L/s of outdoor air to the house, with supplies on the first floor (in the kitchen/dining area) and in each of the three second-floor bedrooms. Air from the first-floor bathroom and both second-floor bathrooms is returned to the HRV before being exhausted, though the HRV was turned off during the tests. The house also has a range hood exhaust and a clothes dryer exhaust, both of which were turned off for the tests. The temperature of the house was measured and the operation of the space conditioning system, including its recirculating air distribution fan, were controlled by a commercially available thermostat.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1983

Tribological measurements on a Charnley-type artificial hip joint

A total hip simulator was used to determine the friction and wear properties of Charnley-type (316L stainless steel balls and sterile ultrahigh molecular weight polyethylene cups) hip prostheses. Three different sets of specimens were tested to 395,000, 101,500 and 233,000 walking cycles, respectively. All tests were run unlubricated, at ambient conditions (22 to 26 C, 30 to 50 percent relative humidity), at 30 walking cycles per minute, under a dynamic load simulating walking. Polyethylene cup wear rates ranged from 1.4 to 39 ten billions cu m which corresponds to dimensional losses of 4.0 to 11 microns per year. Although these wear rates are lower than those obtained from other hip simulators and from in vivo X-ray measurements, they are comparable when taking run-in and plastic deformation into account. Maximum tangential friction forces ranged from 93 to 129 N under variable load (267 to 3090 N range) and from 93 to 143 N under a static load of 3090 N. A portion of one test 250,000 walking cycles) run under dry air ( 1 percent relative humidity) yielded a wear rate almost 6 times greater than that obtained under wet air ( 70 percent relative humidity) conditions.

Jones, W. R., Jr.↗
NASA NTRS2008

Eurasian Reindeer Pastoralism in a Changing Climate: Indigenous Knowledge and NASA Remote Sensing

It is intended that Reindeer Mapper/EALAT will be able to provide reindeer herders with an efficient tool for managing the real-time movements and migrations of their herds through enabling improved efficiency in linking different members of the herder settlements or communities and providing real-time local, satellite or other data (e.g., ice melt in lakes and rivers, weather events), thus enabling real time adjustments to herd movements to avoid problems such as changing weather/climate conditions, freeze-thaw "lock-out" problems, or take advantage of availability of better pasturelands along migration routes. The system is being designed to incorporate local data to allow users to bring their own data into the system for analysis in addition to the data provided by the system itself. With the local information of the population, up to date environmental data and habitat characteristics, the system could generate maps depicting important features of interest for reindeer managers. One of the products derived from the planned Reindeer Mapper system will be a web-based graphic display that allows analysts to quickly pinpoint areas of interest such as those with large concentrations of reindeer and provide surrounding environmental information. The system could be automatically updated with near-real-time information such as hourly precipitation and snowfall rate and accumulation, daily surface and air temperatures, and vegetation cover conditions. The system could bring attention to the proximity of human and animal populations as part of the need for control response. A local GIS will bring these many layers together with several supporting models, showing only a straightforward graphic of the real-time situation in the field. Because the system proposed will be operating in the Internet environment, it should be virtually accessible from any network computers and wireless remote access from the field. The International Center for Reindeer Husbandry in Kautokeino, Norway, is providing regional and international coordination of and access to data sets and expertise, and will act as overall clearinghouse for EALAT information.

Maynard, N. G.↗
DOE OSTI2022

Fine Gradient Electrode and Micro Porous Layer Structures for Improved Heavy Duty Fuel Cells (Final Report)

The commercial deployment of Heavy Duty Fuel Cells(HDFC) for applications such as large trucks (for example, Class 8 capable of carrying 50,000 lb. loads) depends vitally on achieving high efficiency and durability at reasonable costs. Furthermore, the HDFC must operate under practical conditions such as with fuel and air impurities, multiple stop-start cycles, and under the extremes of climate our planet offers – from hot and cold to dry and wet. These conditions place a premium on the stability and utilization of the materials comprising the membrane electrode assemblies (MEAs) powering the fuel cell. and the current catalysts, MicroPorous Layers, and Electrode structures and additives are insufficient for these needs. In Phase I Pajarito and Advent will develop durable electrocatalysts, MicroPorous Layer and electrode additives, and electrode structures for heavy duty fuel cells designed for zero-emission long-haul trucking. The electrocatalyst products are designed to solve the challenging durability and performance needs of fuel cells designed for long life and high efficiency through a combination of uniquely structured designed catalysts as well as new MicroPorous Layers (MPLs) and electrode structure additives. These improved materials will provide Pajarito both an expanded commercial opportunity in electrocatalysts, as well as new markets for MPL and electrode additives. The resulting public benefits include improved economics of fuel cells, a leading zero-emission technology for mobility, as well as reduced reliance on the critical minerals and metals used in the heavy-duty trucks industry. Possible follow-up Phase II and III projects would add full MEA products based on the Phase I efforts catalysts and additives, with full system validation by leading Fuel Cell Truck developers.

08 HYDROGEN↗
NASA NTRS1999

A Survey of Environmental Microbial Flora During Closed Chamber Studies

Services, Inc. and NASA Johnson Space Center, Houston, TX As NASA prepares for long-term missions aboard the International Space Station and the eventual exploration of Mars, closed-environment chambers on Earth have become important test beds for systems evaluations. During 2 separate studies of a selfcontained ecosystem containing 4 crewmembers, microbial surveys of samples from 13 surface and 3 air sites were performed. Microbial concentration of samples from surface sites with frequent water contact (e.g., urinal, sink) did not indicate significantly higher levels of contamination than drier areas, though surface cleaning by the crew may have influenced this conclusion. Changes in bacterial diversity on surface sites implied that the number of transient species was high, suggesting movement by crew activities, aerosols, or both. A non-linear relationship between bacterial diversity and enumeration from surface samples indicated that a rapid increase occurred in the number of species as cell concentration increased to 5 CFU/sq cm. Above this concentration, the number of different bacterial species varied between 11 and 16. Airborne bacteria and fungi averaged only 160 and 1 CFU/m3, respectively. Microbial contamination of the potable water system primarily consisted of 3 species of Gram negative bacteria; however, after 60 days during one study, several species of Bacillus became the dominant flora. This study suggests that under these conditions, microbial contamination in the air and water was suppressed by the life-support systems, though contamination was possible. Conversely, the crew and their activities controlled microbial levels on surfaces. Understanding the factors that affect microbial control will improve the design of microbial testing both during space flight and in analogous Earth-based environments.

Ott, C. Mark↗
NASA NTRSDate not supplied

The Land Surface in Current and Planned MERRA Reanalysis Products

Current global atmospheric reanalysis products such as the European Centre for Medium-Range Weather Forecasts Reanalysis version 5 (ERA5), the NASA Modern-Era Retrospective analysis for Research and Applications version 2 (MERRA-2), and the Japanese Reanalysis for Three Quarters of a Century (JRA-3Q) provide estimates of land surface states and fluxes, including soil moisture, soil temperature, snow mass, latent and sensible heat fluxes, and runoff, that are widely used in research and applications. These land surface estimates are based on land surface process models and, depending on the reanalysis product, on precipitation observations or the assimilation of land surface observations of soil moisture, soil temperature, snow conditions, and screen-level air temperature and humidity from satellite observations and in situ measurements. In this presentation, we review the land surface modeling and data assimilation components of the suite of current and planned MERRA reanalysis products. In addition to MERRA-2, we will discuss the latest NASA reanalysis, MERRA for the 21st century (M21C), which is currently under production, as well as the development and planning of the next version of the MERRA reanalysis, tentatively labeled MERRA-3. In MERRA-2, observations-based precipitation data products are used to correct the precipitation falling on the land surface. Outside of the high-latitudes and Africa, the daily, 0.5-degree, gauge-based Climate Prediction Center (CPC) Unified (CPCU) product is used. In Africa, the pentad, 2.5-degree, satellite- and gauge-based CPC Merged Analysis of Precipitation (CMAP) product is used. Poleward of 62.5 degrees latitude, the land surface sees the precipitation generated by the atmospheric model in the cycling data assimilation system. This configuration provides improved soil moisture estimates compared to those of the original (version 1) MERRA estimates, which did not benefit from the use of precipitation observations. Moreover, the use of precipitation observations facilitates a seamless spin-up of the land surface initial conditions across the MERRA-2 production streams. The use of a gauge-only precipitation product in MERRA-2 across much of the globe, however, adversely impacts the quality of the MERRA-2 land surface estimates in regions with poor gauge coverage, including most of South America and Australia. Therefore, the forthcoming M21C reanalysis uses satellite- and gauge-based precipitation from the Integrated Multi-satellitE Retrievals for the Global Precipitation Measurement Mission (IMERG). This change results in significant improvements in the quality of the M21C soil moisture estimates in the Southern Hemisphere compared to those from MERRA-2. Planning for MERRA-3 focuses on the assimilation of soil moisture observations from the Soil Moisture Active Passive (SMAP) mission and the Advanced Scatterometer (ASCAT), along with snow cover area fraction observations from the Moderate Resolution Imaging Spectroradiometer (MODIS) to further improve the quality of the land surface estimates from the reanalysis. As a first step towards the assimilation of land surface observations in MERRA-3, the offline (land-only) M21C-Land reanalysis is currently under development as a supplemental M21C product that includes the assimilation of SMAP, ASCAT, and MODIS observations. Preliminary results from M21C and M21C-Land will be discussed in the context of MERRA-2 and plans for MERRA-3.

Rolf Reichle↗
DOE OSTI2023

Spectro-Microscopy Studies of Atmospheric Particles

Our project investigated composition and physical properties of individual atmospheric particles collected in field campaigns organized by the DOE Atmospheric Systems Research and Atmospheric Radiation Measurement (ASR/ARM) programs, such as the Green Ocean Amazon (GoAmazon, 2014/5), the Holistic Interactions of Shallow Clouds, Aerosols, and Land-Ecosystems (HI-SCALE, 2016/7), the Aerosol and Cloud Experiment in the Eastern North Atlantic (ACE-ENA, 2017/8), the Aerosol–Ice Formation Closure Pilot Study (AEROICESTUDY, 2019) and in additional small-scale supporting field experiments focused on the investigation of the light-absorbing (aka brown carbon) atmospheric particles. In these studies, we investigated the contribution of natural and anthropogenic sources to populations of atmospheric particles during representative atmospheric conditions; characterized particle composition and evaluated their hygroscopic properties and propensity to act as cloud condensation nuclei (CCN) and ice nuclei (IN); correlated typical particle-type and mixing state characteristics with real-time measurements in the areas of studies. We used multi-modal spectro-microscopy techniques to examine elemental and molecular composition, mixing state, size, and higher order morphology for individual particles. Specifically, we used computer-controlled scanning electron microscopy and X-ray microanalysis for quantitative analysis of particle elemental composition, and we used transmission electron microscopy to provide additional information on the distribution of different components within individual particles (particle heterogeneity). We used synchrotron-based scanning transmission X-ray microscopy for quantitative description of the mixing state and molecular bonding of carbon in particles. The particle composition, mixing state, and morphology from analyzed periods was then combined with the real-time ARM measurements of aerosol size distribution, CCN concentration, hygroscopicity, and aerosol bulk composition. Combined together, results of our studies allowed us to assess the major particle sources (biogenic vs. anthropogenic, primary vs secondary) and gain insight into the atmospheric processing of aerosol particles resulting from condensation, coagulation, oxidative aging, and cloud processing. In collaboration with other scientists involved in field campaigns, we carried out statistical analysis of particle properties and their source-specific contributions to regional aerosol loading under representative air mass, meteorological, and cloud conditions.

scanning transmission X-ray microscopy↗
DOE OSTI2021

Analysis of basic airflow configurations for separate sensible and latent cooling systems with indoor air recirculation

Separate sensible and latent cooling (SSLC) is a technology with efficiency and comfort advantages over conventional cooling systems used for space conditioning of buildings. Using multiple cooling processes at different temperatures allows SSLC to save energy by raising the evaporation temperature of the sensible cooling process. In this paper, all possible airflow configurations of SSLC systems are enumerated under the following constraints: exactly two heat exchangers are used, and air is recirculated to the conditioned space (no exhaust or outdoor air treatment). Seven designs are identified, with varying free operating variables, and each is modeled. Analysis reveals that several configurations are equivalent, and there is only one unique basic airflow SSLC configuration: the one with the sensible and latent heat exchangers placed in series. The efficiency of the SSLC system is compared against that of the conventional system. Under standard conditions, an SSLC system can improve the coefficient of performance by 14.8%. In addition to the numerical simulation, the optimal operating condition of the basic air configuration of the SSLC system is derived analytically. The basic SSLC system is shown to offer the highest performance improvement when the outdoor temperature is relatively cool and the space sensible heat ratio is high.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
NASA NTRS1979

Evaluation of an air solar collector

Performance verification under simulated conditions tested by using Marshall Space Flight Center solar simulator is presented. Evaluation included thermal performance tests, time constant tests, and incident angle modifier tests.

Source record↗
DOE OSTI2019

Bench scale Testing of Next Generation Hollow Fiber Membrane Modules at subambient conditions at the National Carbon Capture Center

Air Liquide is developing a hybrid CO2 capture process based on sub-ambient temperature hollow-fiber membrane operation in combination with cryogenic distillation (Ref 1, 2, 3). Prior work has shown extremely attractive membrane performance. The current work seeks to demonstrate performance of the novel membrane fiber, in commercial form, with flue gas from a coal fired power plant.

Hasse, Dave↗
NASA NTRS1990

Ambient Pressure Test Rig Developed for Testing Oil-Free Bearings in Alternate Gases and Variable Pressures

The Oil-Free Turbomachinery research team at the NASA Glenn Research Center is conducting research to develop turbomachinery systems that utilize high-speed, high temperature foil (air) bearings that do not require an oil lubrication system. Such systems combine the most advanced foil bearings from industry with NASA-developed hightemperature solid-lubricant technology. New applications are being pursued, such as Oil- Free turbochargers, auxiliary power units, and turbine propulsion systems for aircraft. An Oil-Free business jet engine, for example, would be simpler, lighter, more reliable, and less costly to purchase and maintain than current engines. Another application is NASA's Prometheus mission, where gas bearings will be required for the closed-cycle turbine based power-conversion system of a nuclear power generator for deep space. To support these applications, Glenn's Oil-Free Turbomachinery research team developed the Ambient Pressure Test Rig. Using this facility, researchers can load and heat a bearing and evaluate its performance with reduced air pressure to simulate high altitude conditions. For the nuclear application, the test chamber can be purged with gases such as helium to study foil gas bearing operation in working fluids other than air.

Bauman, Steven W.↗
DOE OSTI2021

Simulated aging processes of black carbon and its impact during a severe winter haze event in the Beijing-Tianjin- Hebei region

Black carbon (BC) can mitigate or worsen air pollution through perturbing meteorological conditions. BC aging processes are important for the evolution of particle size, concentration, and optical properties of BC that determines its influence on the meteorology. Here we use the online coupled Weather Research and Forecasting-Chemistry (WRF-Chem) model to quantify the role of BC aging processes, including physical processes (PP) and absorption enhancements (AE), in exerting BC-induced meteorological changes and the associated feedback to PM2.5 (particulate matter less than 2.5 µm in diameter) and O3 concentrations during a severe haze event in Beijing-Tianjin-Hebei (BTH) region during 21-27 February 2014. Our results show that, compared to the simulation without the PP treatment, the simulated near-surface BC concentration and BC mass loading in BTH region is lowered by 6.6 % and 12.1 %, respectively, during the haze event with the PP included. PP increases the proportion of large-size BC (particle diameter greater than 0.312 µm) from 28 %-33 % to 59 %-64 % below 1000 m in BTH region. Both PP and AE enhance the “dome effect” of BC. With both PP and AE considered, a reduction in PBL height due to BC-PBL interaction is 116.3 m (20.7 %), compared to 75.7 m (13.5 %) without AE and 66.6 m (11.9 %) without both PP and AE. However, during this haze event, anomalous northeasterly winds are produced by the direct radiative effect of BC, which further affects the mixing and transport of aerosols. When PBL height is decreased (from 10:00 to 21:00), combining all the impacts on multiple meteorological factors, BC effect without PP and AE, without AE, and with PP and AE, respectively, increases surface concentrations of PM2.5 by 8.3 µg m-3 (6.1 % relative to the mean value), 6.1 µg m-3 (4.5 %) and 9.6 µg m-3 (7.0 %) but decreases surface O3 concentrations by 2.8 ppbv (7.4 %), 4.0 ppbv (9.0 %) and 5.0 ppbv (10.8 %) in BTH region averaged over 21-27 February 2014. Our results highlight the importance of the aging processes and absorption enhancements of BC in simulating weather and air quality.

Chen, Donglin↗
NASA NTRS1976

Study of mesoscale phenomena, winter monsoon clouds and snow area based on LANDSAT data

The author has identified the following significant results. Most longitudinal clouds which appear as continuous linear clouds are composed of small transversal clouds. There are mountain waves of different wavelength in a comparatively narrow area indicating complicated orographical effects on wind and temperature distribution or on both dynamical and static stability condition. There is a particular shape of cirrus cloud suggestive of turbulence in the vicinity of CAT in the upper troposphere near jet stream level and its cold air side. Thin cirrus of overcast condition can be distinguished by MSS; however, extremely thin cirrus of partly cloudy condition cannot be detected even in LANDSAT data. This presents a serious problem in the interpretation of satellite thermal infrared radiation data since they affect the value.

Tsuchiya, K.↗
DOE OSTI2025

Numerical analysis of air dehumidification through electrospray-enhanced vortical flow cyclone separator

The dehumidification of air is a highly energy-intensive process, typically requiring vapor compression systems to cool the air significantly below its dew point temperature. Here, this study numerically investigates air dehumidification achieved by electrostatic and dielectrophoresis forces in a converging duct and centrifugal principles in cyclone separators. An electrospray was employed to energize water droplets, which then captured water vapor via dielectrophoresis. A novelty of the present study is the inclusion of a cyclone separator positioned downstream of the electrospray. This combination increased the dehumidification efficiency and controlled the flow of the condensate. By integrating electrospray technology and applying an electric field, this study examines the impact of particle separation efficiency, pressure drops, and cyclone performance on air dehumidification. The control parameters for air dehumidification were investigated. Three cyclones were modelled for airflow rates of 5 cubic feet per minute [cfm] (0.0024 m 3 /s), 38 cfm (0.0179 m 3 /s), and 200 cfm (0.094 m 3 /s). The results indicated air dehumidification was up to 5.7 % under environmental conditions, similar to those used to validate the CFD model. The degree of air dehumidification was primarily influenced by the electric charge acquired by the water droplets, their flight trajectory, and the vorticity intensity within the cyclone. Air dehumidification could increase by up to 13 % by increasing the number of droplets injected into the air stream, the flight time, and the electrical charge. The breakdown electric field strength threshold near the electrospray was a limiting factor for further enhancing dehumidification performance. This study examines the optimization of an electro-assisted dehumidification system that includes cyclone-based droplet separation through numerical analysis. The results provide insights into the design of energy-efficient air treatment technologies.

42 ENGINEERING↗
NASA NTRS1999

Sensitive Procedures for Determining the Permeation Resistance of Chlorinated Polyethylene Against Liquid Propellants

The permeation resistance of chlorinated polyethylene (CPE) used in totally encapsulating chemical protective suits against the aerospace fuels hydrazine, monomethylhydrazine, and uns-dimethylhydrazine was determined by measuring the breakthrough time (BT) and time-averaged vapor transmission rate (VTR) using procedures consistent with ASTM F 739 and ASTM F 1383. Two exposure scenarios were simulated: a 2 hour (h) fuel vapor exposure, and a liquid fuel "splash" followed by a 2 h vapor exposure. To simulate internal suit pressure during operation, a positive differential pressure of 0.3 in. water (75 Pa) on the collection side of the permeation apparatus was used. Using the available data, a model was developed to estimate propellant concentrations inside an air-line fed, totally encapsulating chemical protective suit. Concentrations were calculated under simulated conditions of fixed vapor transmission rate, variable breathing air flow rate, and variable splash exposure area. Calculations showed that the maximum allowable permeation rates of hydrazine fuels through CPE were of the order of 0.05 to 0.08 ng/sq cm min for encapsulating suits with low breathing air flow rates (of the order of 5 scfm or 140 L min-1). Above these permeation rates, the 10 parts-per-billion (ppb) threshold limit value time-weighted average could be exceeded. To evaluate suit performance at 10 ppb threshold-limiting value/time-weighted average level concentrations, use of a sensitive analytical method such as cation exchange high performance liquid chromatography with amperometric detection was found to be essential. The analytical detection limit determines the lowest measurable VTR, which in turn governed the lowest per meant concentration that could be calculated inside the totally encapsulating chemical protective suit.

Waller, Jess M.↗
NASA NTRS2002

Effect of Environment on Fatigue Behavior of a Nicalon(TM)/Si-N-C Ceramic Matrix Composite

The effect of environmental exposure on the fatigue life of Nicalon(TM) /Si-N-C composite was investigated in this study. Test specimens with arrays of 1.8 mm diameter holes and two different open areas, 25 and 35%, were machined. Three environmental conditions were studied: 1) continuous fatigue cycling in air, 2) fatigue cycling in air alternating with humidity exposure, and 3) fatigue cycling in air alternating with exposure to a salt-fog environment. All fatigue testing on specimens with holes was performed with a load ratio, R = 0.05, and at a temperature of 910 C. In general, fatigue lives were shortest for specimens subjected to salt-fog exposure and longest for specimens subjected to continuous fatigue cycling in air. The fatigue data generated on the specimens with holes were compared with fatigue data generated in air on specimens with no holes. Fatigue strength reduction factors for different environmental conditions and open areas investigated in the study were calculated for the Nicalon(TM) /Si-N-C composite.

Kalluri, Sreeramesh↗
DOE OSTI2023

Evaluation of Atmospheric Conditions Leading to a Fumigation Event

During the afternoon of 30 January 2022, the Savannah River Site experienced unusual temperature conditions leading to a fumigation event that triggered safety alarms and caused considerable confusion about the cause of the event. Normally, it is assumed that fumigation events occur early in the day once surface heating has begun. While most fumigation events are related to the breakup of a nocturnal inversion, this event was related to synoptic atmospheric conditions, which provided a more unique scenario that led to the fumigation event. The unusual synoptic atmospheric conditions led to the downwash and fumigation of the elevated plume, causing a pollutant to mix rapidly to the surface. These conditions could have potentially harmed workers within the facility, since the plume was directed toward a building air intake system. Here, we seek to outline the conditions that led to this unusual fumigation event and provide results of two-dimensional (2D) wind modeling of the event to characterize these conditions for future operational guidance of the facility air intake systems. This work sets the groundwork for future high-resolution modeling to explore the mechanisms and thresholds affecting fumigation on the facility-specific short distance scales and improve forecasting of non-standard fumigation events to protect human health.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1995

A Model for Particle Microphysics, Turbulent Mixing, and Radiative Transfer in the Stratocumulus-Topped Marine Boundary Layer and Comparisons with Measurements

A detailed 1D model of the stratocumulus-topped marine boundary layer is described. The model has three coupled components: a microphysics module that resolves the size distributions of aerosols and cloud droplets, a turbulence module that treats vertical mixing between layers, and a multiple wavelength radiative transfer module that calculates radiative heating rates and cloud optical properties. The results of a 12-h model simulation reproduce reasonably well the bulk thermodynamics, microphysical properties, and radiative fluxes measured in an approx. 500-m thick, summertime marine stratocumulus cloud layer by Nicholls. However, in this case, the model predictions of turbulent fluxes between the cloud and subcloud layers exceed the measurements. Results of model simulations are also compared to measurements of a marine stratus layer made under gale conditions and with measurements of a high, thin marine stratocumulus layer. The variations in cloud properties are generally reproduced by the model, although it underpredicts the entrainment of overlying air at cloud top under gale conditions. Sensitivities of the model results are explored. The vertical profile of cloud droplet concentration is sensitive to the lower size cutoff of the droplet size distribution due to the presence of unactivated haze particles in the lower region of the modeled cloud. Increases in total droplet concentrations do not always produce less drizzle and more cloud water in the model. The radius of the mean droplet volume does not correlate consistently with drizzle, but the effective droplet radius does. The greatest impacts on cloud properties predicted by the model are produced by halving the width of the size distribution of input condensation nuclei and by omitting the effect of cloud-top radiative cooling on the condensational growth of cloud droplets. The omission of infrared scattering produces noticeable changes in cloud properties. The collection efficiencies for droplets less than 30-micrometers radius, and the value of the accommodation coefficient for condensational droplet growth, have noticeable effects on cloud properties. The divergence of the horizontal wind also has a significant effect on a 12-h model simulation of cloud structure. Conclusions drawn from the model are tentative because of the limitations of the 1D model framework. A principal simplification is that the model assumes horizontal homogeneity, and, therefore, does not resolve updrafts and downdrafts. Likely consequences of this simplification include overprediction of the growth of droplets by condensation in the upper region of the cloud, underprediction of droplet condensational growth in the lower region of the cloud, and underprediction of peak supersaturations.

Ackerman, Andrew S.↗