Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Technical Support”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Methylmercury Retention Evaluation to Support Tank 50 and Saltstone Waste Acceptance Criteria: Parts 2 and 3

The objective of this work was to provide a technical basis for the organic mercury waste acceptance criterion (WAC) for Tank 50 salt solution. The current mercury WAC for Tank 50 solution is 325 mg/L as Hg regardless of the form of mercury, which is about three times higher than any total Hg concentrations measured to date in Tank 50 solution. To date, the highest total Hg and MeHg + concentrations in the Tank 50 solution were 105 and 62 mg/L, respectively.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Conference Travel Fellowships: The 10th Annual International Conference on Multiscale Materials Modeling, Baltimore, Maryland, October 19-22, 2020 (Final Technical Report)

The original scope aimed to broaden participation in the 10th International Conference on Multiscale Materials Modeling (MMM 10) by supporting travel and accommodation for 10 junior scientists from U.S. Institutions. A funding request of $\$$10,000 was submitted to partially offset the cost of registration and local accommodation for these early-career participants. Since the award was made close to the date MMM 10 was to be held, we requested a no-cost extension to defer this travel support to the 11th International Conference on Multiscale Materials Modeling (MMM 11), which was held in Prague Congress Center in the Czech Republic. The scope of the travel award remained the same: supporting travel and accommodation for 10 junior scientists from U.S. Institutions.

36 MATERIALS SCIENCE↗
NASA NTRS1991

ECLSS medical support activities

During the period from April 10, 1990 to April 9, 1991, the Consortium for the Space Life Sciences provided technical assistance to the NASA/MSFC water recovery efforts. This assistance was in the form of literature reviews, technical recommendations, and presentations. This final report summarizes the activities completed during this period and identifies those areas requiring additional efforts. The tasks which the University of Alabama in Huntsville (UAH) water recovery team addressed were either identified by MSFC technical representatives or chosen from those outlined in the subject statement of work.

Crump, William J.↗
DOE OSTI2021

Supporting Electric Vehicle Supply Equipment Deployment

FEMP assists federal agencies with the transition to zero-emission vehicles (ZEVs) by offering technical guidance on electric vehicle supply equipment (EVSE) installations and site-specific planning through partnerships with the National Renewable Energy Laboratory's (NREL's) EVSE Tiger Teams. This fact sheet introduces the EVSE Tiger Team site assessment and technical assistance process.

ADVANCED PROPULSION SYSTEMS↗
NASA NTRSDate not supplied

A Decision Support System for Extravehicular Operations Under Significant Communication Latency

Within the next few decades, humanity hopes to perform extravehicular activities (EVAs) on the surface of Mars; however, several technical and operational challenges must first be overcome. Foremost among these challenges is managing a significant two-way communication latency between Earth and Mars. Current and historical paradigms of EVA operations have required near-real-time communication between the crewmember(s) performing an EVA and an Earth-based mission control. Next-generation operational paradigms for supporting deep space exploration will necessitate a distributed decision authority system, including delayed Earth-based mission control, the on-planet extravehicular crewmember(s), and intermediate mission support from intravehicular crewmember(s) within real-time communication range. This latter group is of particular interest: they must provide operations support without the plentiful resources available to mission control on Earth. For this purpose, NASA is developing the Personalized EVA Informatics and Decision Support (PersEIDS) software platform. PersEIDS is designed to bolster operator situational awareness and offload operator workload by automating the tracking and projection of consumables usage over an EVA timeline, providing real-time probabilistic safety assessments of an EVA timeline given consumables constraints, and recommending alternative EVA timeline(s) when the active timeline is not expected to be completed under consumables limits. The PersEIDS concept of operations, use cases, and models will be presented. A limited version of PersEIDS was demonstrated during a three-day-long study where each day a roughly four-hour-long simulated Martian EVA was performed in virtual reality at the NASA Johnson Space Center. The first day was a control trial without PersEIDS support; the second and third days represented different levels of decision support provided by PersEIDS to the intravehicular crewmember acting as mission control. With PersEIDS support, the IV crewmember was able to manage the mission to completion faster and with more remaining consumables; however, additional testing is required to understand confounding factors, e.g. training bias.

Mars↗
NASA NTRS1988

Successful expert systems for space shuttle payload integration

Expert systems are successfully applied to solve recurring NASA Space Shuttle orbiter payload integration problems. Recurrence of these problems is the result of each Space Shuttle mission being unique. The NASA Space Shuttle orbiter was designed to be extremely flexible in its ability to handle many types and combinations of satellites and experiments. This flexibility results in different and unique engineering resource requirements for each of the payload satellites and experiments. The first successful expert system to be applied to these problems was the Orbiter Payload Bay Cabling Expert System (EXCABL), developed at Rockwell International Space Transportation Systems Division. The operational version of EXCABL was delivered in 1986 and successfully solved the payload electrical support services cabling layout problem. As a result of this success, a second expert system, Expert Drawing Matching System (EXMATCH), was developed to generate a list of the reusable installation drawings available for each EXCABL solution. EXMATCH went operational in 1987. As a result of these initial successes, the need for a third expert system was defined and is awaiting development. This new Expert System, called Technical Order Listing Expert System (EXTOL), will generate a list of all the applicable reusable installation drawings available to support the total payload bay mission provisioning and installation effort. This paper describes these expert systems, the individual problems that they were designed to solve, their individual solutions, and the degree of success achieved. These expert systems' instantiate the applicability of this technology to the solution of real-world Space Shuttle payload integration problems.

Morris, Keith↗
DOE OSTI2021

EFA Soil Project Work Order: 554001

Sample analyses were conducted using methodology as outlined in GEL Laboratories, LLC (GEL) Standard Operating Procedures. Any technical or administrative problems during analysis, data review, and reduction are contained in the analytical case narratives in the enclosed data package. The enclosed data package contains the following sections: General Narrative, Chain of Custody and Supporting Documentation, and data from the following fractions: General Chemistry, Metals and Radiochemistry. This package, to the best of my knowledge, is in compliance with technical and administrative requirements.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2017

Unexpected Control Structure Interaction on International Space Station

On June 23, 2011, the International Space Station (ISS) was performing a routine 180 degree yaw maneuver in support of a Russian vehicle docking when the on board Russian Segment (RS) software unexpectedly declared two attitude thrusters failed and switched thruster configurations in response to unanticipated ISS dynamic motion. Flight data analysis after the maneuver indicated that higher than predicted structural loads had been induced at various locations on the United States (U.S.) segment of the ISS. Further analysis revealed that the attitude control system was firing thrusters in response to both structural flex and rigid body rates, which resonated the structure and caused high loads and fatigue cycles. It was later determined that the thruster themselves were healthy. The RS software logic, which was intended to react to thruster failures, had instead been heavily influenced by interaction between the control system and structural flex. This paper will discuss the technical aspects of the control structure interaction problem that led to the RS control system firing thrusters in response to structural flex, the factors that led to insufficient preflight analysis of the thruster firings, and the ramifications the event had on the ISS. An immediate consequence included limiting which thrusters could be used for attitude control. This complicated the planning of on-orbit thruster events and necessitated the use of suboptimal thruster configurations that increased propellant usage and caused thruster lifetime usage concerns. In addition to the technical aspects of the problem, the team dynamics and communication shortcomings that led to such an event happening in an environment where extensive analysis is performed in support of human space flight will also be examined. Finally, the technical solution will be presented, which required a multidisciplinary effort between the U.S. and Russian control system engineers and loads and dynamics structural engineers to develop and implement an extensive modification in the RS software logic for ISS attitude control thruster firings.

Gomez, Susan F.↗
DOE OSTI2022

Fuel Qualification for Molten Salt Reactors

This report supports the development and review of an efficient methodology or process for liquid salt fuel system qualification. The report describes the technical issues encountered when developing an adequate understanding of the fuel salt’s chemical and physical behavior under both normal and accident conditions. The concepts presented in this report align with the fundamental safety functions (FSFs) approach of the more general non-light water reactor (nonLWR) fuel qualification guidance provided in NUREG-2246. However, because liquid salt fuel has substantial technical differences from solid fuels, this report describes tailored approaches for achieving the common safety intents when using liquid salt. The purpose of this report is to illustrate how variations in fuel salt properties impact achievement of FSFs at liquid-salt fueled molten salt reactors (MSRs). The focus on FSFs supports methodology compatibility with both current and developing licensing processes. Customized fuel qualification guidance for liquid salt–fueled Nuclear Power Plants (NPPs) are also provided in this report to supplement the generic non-LWR guidance recently developed by the NRC. As with the broader non-LWR fuel qualification, this report focuses on identification and understanding of fuel life-limiting failure and fuel salt property degradation mechanisms that occur as a result of irradiation during reactor operation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2009

The Deep Impact Network Experiment Operations Center Monitor and Control System

The Interplanetary Overlay Network (ION) software at JPL is an implementation of Delay/Disruption Tolerant Networking (DTN) which has been proposed as an interplanetary protocol to support space communication. The JPL Deep Impact Network (DINET) is a technology development experiment intended to increase the technical readiness of the JPL implemented ION suite. The DINET Experiment Operations Center (EOC) developed by JPL's Protocol Technology Lab (PTL) was critical in accomplishing the experiment. EOC, containing all end nodes of simulated spaces and one administrative node, exercised publish and subscribe functions for payload data among all end nodes to verify the effectiveness of data exchange over ION protocol stacks. A Monitor and Control System was created and installed on the administrative node as a multi-tiered internet-based Web application to support the Deep Impact Network Experiment by allowing monitoring and analysis of the data delivery and statistics from ION. This Monitor and Control System includes the capability of receiving protocol status messages, classifying and storing status messages into a database from the ION simulation network, and providing web interfaces for viewing the live results in addition to interactive database queries.

Delay/Disruption Tolerant Network (DTN)↗
NASA NTRS2012

AES Water Architecture Study Interim Results

The mission of the Advanced Exploration System (AES) Water Recovery Project (WRP) is to develop advanced water recovery systems in order to enable NASA human exploration missions beyond low earth orbit (LEO). The primary objective of the AES WRP is to develop water recovery technologies critical to near term missions beyond LEO. The secondary objective is to continue to advance mid-readiness level technologies to support future NASA missions. An effort is being undertaken to establish the architecture for the AES Water Recovery System (WRS) that meets both near and long term objectives. The resultant architecture will be used to guide future technical planning, establish a baseline development roadmap for technology infusion, and establish baseline assumptions for integrated ground and on-orbit environmental control and life support systems (ECLSS) definition. This study is being performed in three phases. Phase I of this study established the scope of the study through definition of the mission requirements and constraints, as well as indentifying all possible WRS configurations that meet the mission requirements. Phase II of this study focused on the near term space exploration objectives by establishing an ISS-derived reference schematic for long-duration (>180 day) in-space habitation. Phase III will focus on the long term space exploration objectives, trading the viable WRS configurations identified in Phase I to identify the ideal exploration WRS. The results of Phases I and II are discussed in this paper.

Sarguisingh, Miriam J.↗
DOE OSTI2019

Nuclear Fuel Cycle and Supply Chain (NFCSC) Technical Monthly October FY-20

The October FY20 Nuclear Fuel Cycle and Supply Chain (NFCSC) technical monthly report is provided. The usual topics are included: Advanced Fuels Campaign, Material Recovery and Waste Forms Development, MPACT Campaign, Systems Analysis and Integration Campaign, Joint Fuel Cycle Study Activities, and AFCI-HQ program Support.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1992

A feasibility assessment of magnetic bearings for free-piston Stirling space power converters

This report describes a design and analysis study performed by Mechanical Technology Incorporated (MTI) under NASA Contract NAS3-26061. The objective of the study was to assess the feasibility and efficacy of applying magnetic bearings to free-piston Stirling-cycle power conversion machinery of the type currently being evaluated for possible use in long-term space missions. The study was performed for a 50-kWe Reference Stirling Space Power Converter (RSSPC) system consisting of two 25-kWe free-piston Stirling engine modules. Two different versions of the RSSPC engine modules have been defined under NASA Contract NAS3-25463. These modules currently use hydrostatic gas bearings to support the reciprocating displacer and power piston assemblies. Results of this study show that active magnetic bearings of the attractive electromagnetic type are technically feasible for RSSPC application provided that wire insulation with 60,000-hr life capability at 300 C can be developed for the bearing coils. From a design integration standpoint, both versions of the RSSPC were found to be conceptually amenable to magnetic support of the power piston assembly. However, only one version of the RSSPC was found to be amendable to magnetic support of the displacer assembly. Unacceptable changes to the basic engine design would be required to incorporate magnetic displacer bearings into the second version. Complete magnetic suspension of the RSSPC can potentially increase overall efficiency of the Stirling cycle power converter by 0.53 to 1.4 percent (0.15 to 0.4 efficiency points). Magnetic bearings will also overcome several operational concerns associated with hydrostatic gas bearing systems. However, these advantages are accompanied by a 5 to 8 percent increase in specific mass of the RSSPC, depending on the RSSPC version employed. Additionally, magnetic bearings are much more complex, both mechanically and particularly electronically, than hydrostatic bearings. Accordingly, long-term stability and reliability represent areas of uncertainty for magnetic bearings. Considerable development effort will be required to establish the long-term suitability of these bearings for Stirling space power applications.

Curwen, Peter W.↗
DOE OSTI2025

The state of the art for neutron irradiation experiments from the perspective of the High Flux Isotope Reactor (HFIR)

Irradiation experiment campaigns are critical to advancing nuclear energy technologies by providing data on material performance under relevant radiation conditions. Successful irradiation experiments require integrated design efforts that balance technical goals with facility constraints. Here, this paper presents an expert-informed overview of irradiation experiment design at the High Flux Isotope Reactor. It addresses the nuclear materials research and irradiation experiment communities to guide them toward developing technically sound, facility-compatible campaigns. The High Flux Isotope Reactor is a multipurpose reactor supporting isotope production, neutron scattering, and materials testing. Its high, steady-state neutron flux is ideal for irradiation experiments, but successful execution demands coordinated thermal, structural, and reactor physics analyses. The paper outlines the complete development workflow from concept definition and design optimization to safety qualification and post-irradiation examination. Standardized capsule platforms are also discussed in terms of flexibility, specimen capacity, and thermal performance. Common failure modes such as unanticipated geometric variations, can impact temperature-dose profiles and compromise data reliability. Therefore, detailed thermal modeling and accurate as-built characterization are essential for meaningful post-irradiation data interpretation. Key recommendations include early engagement all stakeholders, clearly defined design expectations, and alignment of specimen geometries with post-irradiation examination capabilities. This approach reduces design iterations, enhances data quality, and supports more efficient use of irradiation resources. Strategic and well-planned irradiation testing not only improves individual campaign success but also accelerates the deployment of advanced nuclear technologies. By closing critical data gaps and reducing development risks, the nuclear materials community can more effectively contribute to the future of clean, resilient energy systems.

Experiments↗
DOE OSTI2023

Utah FORGE 4-2541: Optimization and Validation of a Plug-and-Perf Stimulation Treatment Design - Workshop Presentation

This is a presentation on the Optimization and Validation of a Plug-and-Perf Stimulation Treatment Design at Utah FORGE project by Fervo Energy, presented by Sireesh Dadi. The project's objective was to develop a multistage hydraulic stimulation approach designed specifically to target the top three factors that control the technical and commercial viability of an EGS system. These factors include: achieving sufficient injectivity to support high cross-well flow rates, distributing flow evenly across the wellbore and reservoir, and overcoming the effects of stress heterogeneity, stress shadowing, and variations in natural fracture properties during the stimulation treatment. This presentation was featured in the Utah FORGE R&D Annual Workshop on September 7, 2023. The workshop provided a valuable opportunity to explore the progress made in each of the 17 Research and Development projects funded under Solicitation 2020-1 which aim to enhance our understanding of the crucial factors influencing the development of Enhanced Geothermal Systems (EGS) reservoirs and resources.

15 GEOTHERMAL ENERGY↗
DOE OSTI2023

Inaugural Technologist in Communities Scanning Tour: Automated and Electrified On-Demand Mobility (Follow-On Summary Report: April 24-25, 2023) [Slides]

In 2023, the Technologist in Communities (TIC) program hosted its inaugural scanning tour across the American Southwest, with a goal of investigating the region's leading public mobility systems and their integration with on-demand public mobility services. The scanning tour concept was inspired by and named after a U.S. Department of Transportation Federal Highway Administration practice of hosting "scanning tours," both domestically and abroad, to explore innovative transportation practices throughout the 1990s and early 2000s. Guided by the idea that "seeing is believing," scanning tours created opportunities for government and industry representatives to collectively experience new technologies and best practices firsthand. In 2023, the National Renewable Energy Laboratory (NREL) followed suit by leading the inaugural TIC scanning tour. TIC, part of the Technology Integration program within the U.S. Department of Energy's (DOE's) Vehicle Technologies Office, supports positive energy and mobility outcomes in communities across rural to urban contexts. TIC enables technical experts to work directly with leaders and stakeholders in communities and assist them in implementing promising new technologies. This first TIC scanning tour invited NREL, DOE, and industry experts to survey innovative public mobility practices and their integration into public transit systems across the Southwest. The tour's goals included examining the state of innovation in public mobility in cities, communities, and airports; facilitating collaboration between entities; and sparking potential new partnerships. The following report summarizes key findings from the scanning tour.

24 POWER TRANSMISSION AND DISTRIBUTION↗