Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Shape”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Rapid synthesis of spherical-shaped green-emitting MgGa{sub 2}O{sub 4}:Mn{sup 2+} phosphor via spray pyrolysis

Simple, one-step synthesis of spherical-shaped powder phosphors with aqueous precursors via a spray pyrolysis method is reported. Green-emitting MgGa{sub 2}O{sub 4}:Mn{sup 2+} phosphor with a controlled shape was successfully obtained by spraying under a reductive atmosphere (N{sub 2} + H{sub 2} carrier gas) without high-temperature post-heat treatment. In addition, the corresponding powder phosphors were well dispersed and showed a clean surface morphology compared to an existing cumbersome process using high-temperature post-annealing. The new method may help to prevent surface residual non-radiative defect sites. The result of highly luminescent and spherical morphology, non-aggregated powder phosphor by this procedure holds promise for a cost-effective and rapid synthesis process for conventional inorganic phosphors.

36 MATERIALS SCIENCE↗

Shape evolution of Cu-doped Mn{sub 3}O{sub 4} spinel microcrystals: influence of copper content

Spinel-type Cu-doped Mn{sub 3}O{sub 4} microcrystals with various shapes were synthesized by hydrothermal method. The interrelation between the preparative conditions and the composition, structure, and morphology of the products were investigated using various analytical techniques, such as X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and thermal gravimetric analysis. Results revealed that the introduction of Cu{sup 2+} ions into the reaction system promoted the formation of single phase Cu-doped Mn{sub 3}O{sub 4}. A gradual shape evolution from polyhedron to octahedron occurred upon increasing the additive copper content. Complete decolorization of organic dye (methylene blue) aqueous solution was achieved by treating the dye with Cu-doped Mn{sub 3}O{sub 4} in acidic media, which shows the possible application of doped Mn{sub 3}O{sub 4} as effective reagents for the degradation of organic contaminants in water.

36 MATERIALS SCIENCE↗

Transformation behavior and shape memory characteristics of thermo-mechanically treated Ti–(45−x)Ni–5Cu–xV (at%) alloys

Transformation behavior, shape memory characteristics and superelasticity of thermo-mechanically treated Ti–(45−x)Ni–5Cu–xV (at%) (x = 0.5–2.0) alloys were investigated by means of differential scanning calorimetry, transmission electron microscopy, X-ray diffractions, thermal cycling tests under constant load and tensile tests. The B2–B19′ transformation occurred when V content was 0.5 at%, above which the B2–B19–B19′ transformation occurred. The B2–B19 transformation was not separated clearly from the B19–B19′ transformation. Thermo-mechanically treated Ti–(45−x)Ni–5Cu–xV alloys showed perfect shape memory effect and transformation hysteresis(ΔT) of Ti–43.5Ni–5.0Cu–1.5V and Ti–43.0Ni–5.0Cu–2.0V alloys was about 9 K which was much smaller than that of a Ti–44.5Ni–5.0Cu–0.5V alloy(23.3 K). More than 90% of superelastic recovery ratio was observed in all specimens and transformation hysteresis (Δσ) of a Ti–44.5Ni–5.0Cu–0.5V alloy was about 70 MPa, which was much larger than that of a Ti–43.0Ni–5.0Cu–2.0V alloy (35 MPa).

36 MATERIALS SCIENCE↗

Thermodynamic constitutive model for load-biased thermal cycling test of shape memory alloy

Graphical abstract: - Highlights: • Thermodynamic calculation model for martensitic transformation of shape memory alloy was proposed. • Evolution of the self-accommodation was considered independently by a rate-dependent kinetic equation. • Finite element calculation was conducted for B2–B19′ transformation of Ti–44.5Ni–5Cu–0.5 V (at.%). • Three-dimensional numerical results predict the macroscopic strain under bias loading accurately. - Abstract: This paper presents a three-dimensional calculation model for martensitic phase transformation of shape memory alloy. Constitutive model based on thermodynamic theory was provided. The average behavior was accounted for by considering the volume fraction of each martensitic variant in the material. Evolution of the volume fraction of each variant was determined by a rate-dependent kinetic equation. We assumed that nucleation rate is faster for the self-accommodation than for the stress-induced variants. Three-dimensional finite element analysis was conducted and the results were compared with the experimental data of Ti–44.5Ni–5Cu–0.5 V (at.%) alloy under bias loading.

36 MATERIALS SCIENCE↗

Upcycling of aluminum Twitch scrap via Shear Assisted Processing and Extrusion (ShAPE)

Aluminum is publicly perceived as recyclable, but mixed alloys and impurities in aluminum scrap require dilution via energy-intensive primary aluminum or downcycling to low-quality castings. In this study, cast billets of shredded aluminum scrap (Twitch) were blended with pre-consumer AA 6061, extruded into tubes via Shear Assisted Processing and Extrusion (ShAPE), and aged to T1 and T6 tempers. Microscopy reveals that ShAPE refined and distributed the deleterious AlFeSi phases. Furthermore, the Twitch extrusions had tensile properties comparable to AA 6061 yet without homogenizing or adding primary aluminum. Energy savings were 85% compared to conventional extrusion of primary aluminum alloys.

ShAPE↗

High-energy synchrotron radiation X-ray diffraction measurements during in situ aging of a NiTi-15 at. % Hf high temperature shape memory alloy

NiTiHf high temperature shape memory alloys (HTSMAs) have begun to show considerable progress in their ability to be manufactured and are now on the cusp of becoming viable alloys for use in the aerospace industry, mainly as actuation devices. By aging the alloys at intermediate temperatures between 450 and up to 700 °C, Ni-rich NiTiHf HTSMAs form the H-phase, a Ni-rich nanoscale precipitate which can be used to strengthen the alloy and improve the shape memory response; however, precipitate phase evolution and growth has not yet been studied in-situ nor have the effects of previous thermo-mechanical processing on their formation. In this study, H-phase precipitate formation is observed experimentally in situ during aging of a Ni-rich NiTiHf alloy using high energy synchrotron radiation X-ray diffraction (SR-XRD) measurements. The effects of prior thermo-mechanical treatments, i.e. hot and cold rolling, on its formation rate and coarsening rate are compared. It is shown that growth of the H-phase can be observed in situ using SR-XRD and the H-phase formation rate seems to exhibit linear growth when aging at 550 °C, while increasing the temperature to 650 °C shows a logarithmic trend that plateaus after approximately 1 h of aging. Other properties such as incubation time, austenite lattice strains, texture evolution, and overall comparison between hot and cold rolling are discussed. New potential peak age conditions are suggested based on the diffraction data and evaluated using three-point bending and TEM imaging.

36 MATERIALS SCIENCE↗

Pulse shape discrimination of Cs 2 LiYCl 6 :Ce 3+ detectors at high count rate based on triangular and trapezoidal filters

Cs 2 LiYCl 6 :Ce 3+ (CLYC) detectors have demonstrated the capability to simultaneously detect γ-rays and thermal and fast neutrons with medium energy resolution, reasonable detection efficiency, and substantially high pulse shape discrimination performance. In this work, a disadvantage of CLYC detectors is the long scintillation decay times, which causes pulse pile-up at moderate input count rate. Pulse processing algorithms were developed based on triangular and trapezoidal filters to discriminate between neutrons and γ-rays at high count rate. The algorithms were first tested using low-rate data. They exhibit a pulse-shape discrimination performance comparable to that of the charge comparison method, at low rate. Then, they were evaluated at high count rate. Neutrons and γ-rays were adequately identified with high throughput at rates of up to 375 kcps. The algorithm developed using the triangular filter exhibits discrimination capability marginally higher than that of the trapezoidal filter based algorithm irrespective of low or high rate. The algorithms exhibit low computational complexity and are executable on an FPGA in real-time. Finally, they are also suitable for application to other radiation detectors whose pulses are piled-up at high rate owing to long scintillation decay times.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

RF pulse shape control in the compact linear collider test facility

The Compact Linear Collider (CLIC) is a study for an electron–positron machine aiming at accelerating and colliding particles at the next energy frontier. The CLIC concept is based on the novel two-beam acceleration scheme, where a high-current low-energy drive beam generates RF in series of power extraction and transfer structures accelerating the low-current main beam. To compensate for the transient beam-loading and meet the energy spread specification requirements for the main linac, the RF pulse shape must be carefully optimized. This was recently modelled by varying the drive beam phase switch times in the sub-harmonic buncher so that, when combined, the drive beam modulation translates into the required voltage modulation of the accelerating pulse. In this paper, the control over the RF pulse shape with the phase switches, that is crucial for the success of the developed compensation model, is studied. The results on the experimental verification of this control method are presented and a good agreement with the numerical predictions is demonstrated. Implications for the CLIC beam-loading compensation model are also discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Performance evaluation of an energy tuning assembly for neutron spectral shaping

An energy tuning assembly (ETA) was designed here to be fielded at the National Ignition Facility (NIF) to modify the characteristic D-T fusion spectrum to include a prompt fission neutron spectral component. The ETA was characterized at the 88-Inch Cyclotron at Lawrence Berkeley National Laboratory to measure the shaped spectrum from an incident deuteron breakup neutron source, test the proposed neutron spectroscopy techniques used to inform the flux measurements at NIF, and validate the ability to predict ETA performance using a Monte Carlo Neutral Particle (MCNP) simulation. Activation foils (i.e., Ni, In, Au, Al) were exposed to a collimated 33-MeV deuteron-breakup beam originating from a tantalum breakup target. The source spectrum absent the ETA was characterized using a set of activation foils and the STAYSL unfolding code. Finally, the ETA-modified spectrum was obtained using activation foil unfolding with a χ 2 ν = 0 . 92 . The ETA-modified unfolded spectrum agreed with the MCNP-simulated prediction in the energy range of 0.1–14 MeV, but exhibited disagreements in the 10 eV–100 keV region. This work demonstrates shaping of the NIF neutron spectrum via the ETA to be a viable path forward for tailored neutron beams at NIF.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A functional form for liquid scintillator pulse shapes

Digitization of detector signals enables analysis of the original waveform to extract timing, particle identification, and energy deposition information. Here we present the use of analytical functions based on sigmoids to model and fit such pulse shapes from liquid organic scintillators, though the method should also be applicable to other detector systems. Neutron and gamma interactions in NE213 detectors were digitized from the phototube anode and fit using a sigmoid-based function. The acuity of the fit in extracting timing information and performing neutron-gamma pulse-shape discrimination are presented and discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Characterization and pulse-shape discrimination of a multi-stacked structure of ZnS: Ag/PMMA for fast-neutron detection in high-flux environments

The Micro-Layered Fast Neutron Detector (MLFD) is a proton-recoil scintillator that incorporates the basic concept of a Hornyak button detector with an improved design using a layered structure of ZnS:Ag and PMMA (polymethyl methacrylate). The MLFD was predicted to have low sensitivity to gamma rays, hence pulse shape discrimination was performed to determine the gamma-ray contribution. Presented in this paper are the pulse-shape discrimination characteristics of the MLFD. Additionally, the charge integration technique was employed to discriminate between the neutrons and gamma rays using a fast digitzer. The MLFD was found to exhibit excellent neutron/gamma-ray discrimination, with the highest Figure-of-Merit (FoM) being 4.56. With PSD, the neutron signal is distinct from gamma-ray, Ĉerenkov and electronic noise signals. This clear separation was achieved due to the large differences in decay times of the neutron and gamma-ray-induced pulses in the ZnS:Ag phosphor. The MLFD can be employed in high gamma-ray exposure fields, up to at least 1287.7 mR/hr, without appreciable degradation in PSD performance.

47 OTHER INSTRUMENTATION↗

Performance evaluation of pulse shape discrimination capable organic scintillators for space applications

Scintillators with pulse-shape discrimination (PSD) capability are of great interest to many fields in the scientific community. The ability to discern a gamma ray from a neutron using PSD varies between different types of scintillator materials and dopants. Here a new generation of organic scintillator materials with PSD capability were studied to determine their radiation hardness to neutron and gamma-ray radiation. The PSD capability, average pulse shapes, and light output of four types of organic scintillator were characterized before and after neutron and gamma-ray irradiation. The main goal of this investigation is to study the effects of long-term irradiation that may be experienced in space applications on the light output and particle discriminating capabilities of each material. EJ-270, EJ-276, organic glass, and Stilbene were tested. Damage due to neutron irradiation (displacement damage) was not observed in any of the scintillators up to 2.56 x 10 11 n/cm 2 , except for Stilbene which showed a small (12%) decrease in light output. All scintillators presented some light output reduction after gamma-ray irradiation (total ionizing dose), with reductions of 17% (EJ-276 and OGS), 32% (EJ-270), and 42% (Stilbene) observed immediately after 100 kRad.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Jet shapes and fragmentation functions in Au+Au collisions at s NN = 200 GeV in STAR

The STAR Collaboration reports measurements of differential jet shapes and semi-inclusive jet fragmentation functions in Au+Au collisions at with the STAR detector at RHIC. Additionally, jet shapes, which represent the radial distribution of momentum carried by constituents, are measured differentially for (1) the charged particles transverse momentum and (2) the jet azimuthal angle relative to the second-order event plane. Based on the semi-inclusive population of jets recoiling from a high transverse momentum trigger hadron, jet fragmentation functions in 40-60% central heavy-ion collisions are measured, and compared to those in PYTHIA simulations for pp collisions.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Coherent addition of high power broad-area laser diodes with a compact VBG V-shaped external Talbot cavity

In this paper, we introduced a compact V-shaped external Talbot cavity for phase locking of high power broad-area laser diodes. The length of compact cavity is ~25 mm. Near diffraction-limit coherent addition of 10 broad-area laser diodes indicated that high quality phase locking was achieved. We measured the near-field emission mode of each individual broad-area laser diode with different feedback, such as a volume Bragg grating and a high reflection mirror. Finally, we found out that the best result of phase locking broad-area laser diodes was achieved by the compact V-shaped external Talbot cavity with volume Bragg grating feedback.

42 ENGINEERING↗

All-fiber, discrete arbitrary picket-pulse shaping

Here, a novel all-fiber, hybrid pulse-shaping system based on the temporal stacking of discrete optical picket pulses combined with continuously shaped optical pulses provides 100-ps resolution with the high dynamic range and flexibility required for laser fusion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Micro Fourier Transform Profilometry (μFTP): 3D shape measurement at 10,000 frames per second

We report that fringe projection profilometry is a well-established technique for optical 3D shape measurement. However, in many applications, it is desirable to make 3D measurements at very high speed, especially with fast moving or shape changing objects. In this work, we demonstrate a new 3D dynamic imaging technique, Micro Fourier Transform Profilometry (μFTP), which can realize an acquisition rate up to 10,000 3D frame per second (fps). The high measurement speed is achieved by the number of patterns reduction as well as high-speed fringe projection hardware. In order to capture 3D information in such a short period of time, we focus on the improvement of the phase recovery, phase unwrapping, and error compensation algorithms, allowing to reconstruct an accurate, unambiguous, and distortion-free 3D point cloud with every two projected patterns. We also develop a high-frame-rate fringe projection hardware by pairing a high-speed camera and a DLP projector, enabling binary pattern switching and precisely synchronized image capture at a frame rate up to 20,000 fps. Lastly, based on this system, we demonstrate high-quality textured 3D imaging of 4 transient scenes: vibrating cantilevers, rotating fan blades, flying bullet, and bursting balloon, which were previously difficult or even unable to be captured with conventional approaches.

3D shape measurement↗

Damping and mode shape modification for additively manufactured walls with captured powder

Here, this paper describes the fabrication, modeling, and dynamic testing of laser powder bed fusion stainless steel walls with captured powder cores. The purpose of the study is to determine the increased structural damping, or energy dissipation, and mode shape modification caused by the inclusion of the unmelted powder core within the solid walls. It is shown experimentally that the damping increases with larger powder core width and that the damping addition is mode dependent. Damping increases over the solid wall values by factors of 2.9–225 are reported depending on the mode number and core width. It is also seen that the mode shapes are distorted relative to the solid wall results as the core width is increased and wall thickness is decreased. Comparisons with finite element models confirm this trend.

42 ENGINEERING↗

Tuning the Mechanical Properties of Shape Memory Metallic Glass Composites with Brick and Mortar Designs

We use molecular dynamics simulations to characterize the tensile deformation and failure of shape memory alloy-bulk metallic glass composites (BMGCs). As the failure in BMGCs shifts from the MG matrix to the second phase different strategies are required to further improve their mechanical properties. Results show that a staggered brick BMGC displays enhanced ductility with mild strength loss following a homogeneously distributed plasticity. This demonstrates that judiciously designed BMGCs can effectively synergize the mechanical properties of metallic glasses and shape memory alloys by effectively distributing stress and preventing the generation of critical shear bands and premature failure while preserving strength.

36 MATERIALS SCIENCE↗