Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROUGHNESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Observations of the seasonal variability of soil moisture and vegetation cover over Africa using satellite microwave radiometry

Multispectral passive microwave data from the scanning multichannel microwave radiometer (SMMR) on the Nimbus-7 satellite were processed selectively for a 1 yr period over Africa. The data show a wide dynamic range of brightness temperature (180 to 290 K), corresponding to variations in surface features such as moisture, temperature, vegetation, roughness, and large-scale topography. It appears that soil moisture variability is detectable with the SMMR over large regions of Africa. To what extent roughness and vegetation affect this capability is not clear. The lowest SMMR frequency is C-band (6.6 GHz), thus any soil moisture sensitivity at this frequency would be much improved by a sensor at L-band (1 to 2 GHz) less affected by roughness and vegetation.

Njoku, Eni G.↗
NASA NTRS1986

Are the virial masses of clusters smaller than we think?

The constraints that the available X-ray spectral and imaging data place on the mass distribution and mass to light ratio of rich clusters are considered. It was found for the best determined cases that the mass to light ratio is less than 125 h sub 50 at radii exceeding 1 h sub 50 Mpc. The mass to light ratio is approximately constant at radii exceeding 1 h sub 50 Mpc but may rise to values of roughly 200 h sub 50 in the central regions. The fraction of the total mass that is in baryons, primarily the hot X-ray emitting gas, is roughly 30% thus setting the mass to light ratio of the dark material to roughly 70. The model that fits the X-ray data for Coma is in good agreement with the observed optical velocity dispersion vs. radius data.

Cowie, L. L.↗
NASA NTRS1986

Development and testing of vortex generators for small horizontal axis wind turbines

Vortex generators (VGs) for a small (32 ft diameter) horizontal axis wind turbine, the Carter Model 25, have been developed and tested. Arrays of VGs in a counterrotating arrangement were tested on the inbound half-span, outboard half-span, and on the entire blade. VG pairs had their centerlines spaced at a distance of 15% of blade chord, with a spanwise width of 10% of blade chord. Each VG had a length/height ratio of 4, with a height of between 0.5% and 1.0% of the blade chord. Tests were made with roughness strips to determine whether VGs alleviated the sensitivity of some turbines to an accumulation of bugs and dirt on the leading edge. Field test data showed that VGs increased power output up to 20% at wind speeds above 10 m/s with only a small (less than 4%) performance penalty at lower speeds. The VGs on the outboard span of the blade were more effective than those on inner sections. For the case of full span coverage, the energy yearly output increased almost 6% at a site with a mean wind speed of 16 mph. The VGs did reduce the performance loss caused by leading edge roughness. An increase in blade pitch angle has an effect on the power curve similar to the addition of VGs. VGs alleviate the sensitivity of wind turbine rotors to leading edge roughness caused by bugs and drift.

Gyatt, G. W.↗
NASA NTRS1987

Comparison of Hirs' equation of Moody's equation for determining rotordynamic coefficients of annular pressure seals

The rotordynamic coefficients of an incompressible-flow annular pressure seal were determined using a bulk-flow model in conjunction with two different friction factor relationships. The first, Hirs' equation, assumes the friction factor is a function of Reynolds number only. The second, Moody's equation, approximates Moody's diagram and assumes the friction factor is a function of both Reynolds number and relative roughness. For each value of relative roughness, Hirs' constants were determined so that both equations gave the same magnitude and slope of the friction factor. For smooth seals, both relationships give the same results. For rough seals (e/2 H sub 0 = 0.05) Moody's equation predicts 44% greater direct stiffness, 35% greater cross-coupled stiffness, 19% smaller cross-coupled damping, 59% smaller cross-coupled inertia, and nominally the same direct damping and direct inertia.

Nelson, Clayton C.↗
NASA NTRS1987

Development of wind tunnel techniques for the solution of problems in planetary Aeolian processes

Kutzbach reports wind profiles over a series of roughness elements on a frozen lake and how the wind profile changed as the surface roughness was varied. The approach of the current study was to duplicate Kutzbach's roughness arrays in the wind tunnel at 1/20 and 1/40 scales, and to compare the wind profiles over these scale models to those derived by Kutzbach at full scale in the field. The effects of scale differences and data reduction techniques are discussed. Although the study suggests that wind tunnel scale models can predict parameters measured in the field, the development of more definitive guidelines requires a field experiment designed specifically for comparison with wind tunnel results.

Sullivan, Robert↗
NASA NTRS1986

Comparison of Hirs' equation with Moody's equation for determining rotordynamic coefficients of annular pressure seals

The rotordynamic coefficients of an incompressible-flow annular pressure seal were determined using a bulk-flow model in conjunction with two different friction factor relationships. The first, Hirs' equation, assumes the friction factor is a function of Reynolds number only. The second, Moody's equation, approximates Moody's diagram and assumes the friction factor is a function of both Reynolds number and relative roughness. For each value of relative roughness, Hirs' constants were determined so that both equations gave the same magnitude and slope of the friction factor. For smooth seals, both relationships give the same results. For rough seals, Moody's equation predicts 44 percent greater direct stiffness, 35 percent greater cross-coupled stiffness, 19 percent smaller cross-coupled damping, 59 percent smaller cross-coupled inertia, and nominally the same direct damping and direct inertia.

Nelson, C. C.↗
NASA NTRS1987

Are the virial masses of clusters smaller than we think?

The constraints that the available X-ray spectral and imaging data place on the mass distribution and mass to light ratio of rich clusters are considered. It was found for the best determined cases that the mass to light ratio is less than 125 h sub 50 at radii exceeding 1 h sub 50 Mpc. The mass to light ratio is approximately constant at radii exceeding 1 h sub 50 Mpc but may rise to values of roughly 200 h sub 50 in the central regions. The fraction of the total mass that is in baryons, primarily the hot X-ray emitting gas, is roughly 30 percent thus setting the mass to light ratio of the dark material to roughly 70. The model that fits the X-ray data for Coma is in good agreement with the observed optical velocity dispersion vs. radius data.

Cowie, L. L.↗
NASA NTRS1987

Theoretical and experimental study of the radar backscatter of Arctic sea ice

The present theoretical model for sea ice radar backscatter has supported parametric studies of radar signature sensitivity to changes in salinity, temperature, brine volume, density, air bubble size, and surface roughness. Parametric study results indicate that first-year and multiyear ice may be confused when first-year ice is very rough and has exceptionally high salinity, as well as being only a few degrees C from the melting point. Confusion also arises when multiyear ice is slightly more saline, the temperature is a few degrees C from the melting point, surface is moderately rough, and air bubbles are small but still typical of multiyear ice.

Onstott, Robert G.↗
NASA NTRS1987

Interseismic deformation for normal fault earthquakes

Comparison between the coseismic vertical deformation associated with normal fault earthquakes and permanent deformation indicated by geologic structure indicates that large deformation must occur during the period between earthquakes. When sufficient geodetic and geologic information is available it is possible to estimate the spatial character of this interseismic deformation. A case in point is the 1983 Borah Peak, Idaho earthquake. This normal fault earthquake produced roughly 5 times as much basin subsidence as it did uplift of the adjacent mountain ranges. In contrast, geophysical and geological observations show that the basin is roughly as deep as the bounding range is high. A similar normal fault event in the Basin and Range, the 1959 Hebgen Lake earthquake, was also accompanied by substantially larger subsidence than uplift. In this case, postseismic geodetic measurements show broad regional uplift with a spatial pattern which is roughly consistent with that proposed for the Borah Peak event. Modeling suggests that postseismic viscoelastic relaxation and strain accumulation in an elastic lithosphere overlying a viscoelastic asthenosphere are possible physical mechanisms to generate interseismic uplift. These mechanisms may be the contemporary expression of those processes responsible for the high elevation of the Basin and Range Province.

Reilinger, Robert↗
NASA NTRS1987

Boundary layer simulator (BLIMPJ) improvement

Improvements were made to advance the current Boundary Layer Integral Matrix Procedure - Version J (BLIMPJ) containing previously modeled simplified calculation methods accounting for surface roughness, relaminarization, and thick boundary layer effects. These improvements have potential applications in the design of the future Orbit Transfer Vehicles (OTV) engines. The coded wall roughness module was validated successfully against measured data from the LeRC 60-15 degree half-angle conical nozzle. The relaminarization model was modified to include wall cooling and roughness based on a set of test data from the same nozzle. The model was compared against typical data sets for validation in different flow regimes. The thrust loss calculation for thick boundary layer effects was computerized where the iterations between TDK and BLIMPJ proceeded automatically until convergence was achieved. An example is given for a typical OTV nozzle with an area ratio 1293.

Praharaj, S. C.↗
NASA NTRS1988

Evidence for change in particle excitation of Jupiter's atmosphere 1968-1979

Analysis of the Pioneer 10 and rocket observations of disk averaged emission from the sunlit atmosphere of Jupiter indicates that the spectrally integrated EUV brightness was reduced by at least a factor of two relative to Voyager spacecraft observations in 1979. Most of the variation is caused by the H Ly-alpha component in the spectrum, which was reduced roughly one order of magnitude near the time of solar minimum in 1972-1973. Although the analysis of the data does not produce entirely consistent results, the weight of evidence points to a factor of order roughly two lower abundance of H in Jupiter's atmosphere in 1972-1973 relative to 1979. The low emission rate in H Ly-alpha near the time of solar minimum in this proposed scenario is caused by an electroglow energy depositon rate reduced by a factor of roughly three. The apparent reduced abundance of H implies a reduced thermospheric temperature, even under the assumption of a constant electroglow deposition rate.

Shemansky, D. E.↗
NASA NTRS1988

Calculation of the effects of ice on the backscatter of a ground plane

Described is a technique for examining the effect of a rough ice layer on the backscatter of a ground plane. The technique is applied to the special case of a rough ice layer that is periodic in space. By assuming that the roughness is periodic, the backscatter of the ground plane can be found from the backscatter of a single period. Backscatter calculations are presented for a single period in which the thickness of the ice layer has a Gaussian shape.

Lambert, K. M.↗
NASA NTRS1988

Inference of geologic surface parameters from polarimetric radar observations and model inversion

The results of inferring geologic parameters such as rms surface height, correlation length, and dielectric constant of rough surfaces by fitting observed polarization signatures with those predicted by the second order Rice model are discussed. The inferred results are compared to measured values of rms height and correlation length. The rms height values inferred are in good agreement with in situ measurements. The inferred correlation lengths generally do not agree with measured values. The results allow the separation of the effects of surface roughness and dielectric constant on the overall backscatter from rough surfaces.

Vanzyl, Jakob J.↗
NASA NTRS1988

Active microwave measurements of artificial sea ice

A 5 m x 15 m outdoor tank of 1.2 m depth was filled with sea water, and polarimetric radar backscatter data were collected at 1.8, 5, and 10 GHz for incidence angles 0 to 60 deg. Observations commenced with open water and continued until 30 cm of sea ice formed. The roughness of the ice surface is important in determining the general backscatter level for first-year ice. Experiments were performed to study the change in backscatter with various roughness scales. Effects of freeze and thaw conditions were also examined. Absolute backscatter levels for new to gray ice are small, except for the large, coherent returns at vertical. The backscatter responses of new, gray, rough grey, and desalinated first-year ice at linear polarization are dissimilar. This is confirmed by examining their polarization signatures.

Onstott, R. G.↗
NASA NTRS1987

The effects of wall surface defects on boundary-layer transition in quiet and noisy supersonic flow

The design of supersonic vehicles with laminar flow control and vehicles such as the Space Shuttle requires information on allowable transition tolerances to fabrication defects such as discrete surface roughness and waviness. A relatively large data base on the effects of discrete roughness on transition exists for subsonic and supersonic speeds. The existing supersonic wind tunnel transition data are contaminated by wind tunnel noise emanating from the turbulent boundary layers on the nozzle walls. Roughness and waviness transition data obtained in a quiet Mach 3.5 supersonic wind tunnel are compared with those obtained in conventional noisy flows.

Morrisette, E. Leon↗
NASA NTRS1990

Heat transfer measurements from a NACA 0012 airfoil in flight and in the NASA Lewis icing research tunnel

Local heat transfer coefficients from a smooth and roughened NACA 0012 airfoil were measured using a steady state heat flux method. Heat transfer measurements on the specially constructed 0.533 meter chord airfoil were made both in flight on the NASA Lewis Twin Otter Research Aircraft and in the NASA Lewis Icing Research Tunnel (IRT). Roughness was obtained by the attachment of small, 2 mm diameter, hemispheres of uniform size to the airfoil surface in four distinct patterns. The flight data was taken for the smooth and roughened airfoil at various Reynolds numbers based on chord in the range of 1.24x10(exp 6) to 2.50x10(exp 6) and at various angles of attack up to 4 degrees. During these flight tests the free stream velocity turbulence intensity was found to be very low (less than 0.1 percent). The wind tunnel data was taken in the Reynolds number range of 1.20x10(exp 6) to 4.52x10(exp 6) and at angles of attack from -4 degrees to +8 degrees. The turbulence intensity in the IRT was 0.5 to 0.7 percent with the cloud making spray off. Results for both the flight and tunnel tests are presented as Frossling number based on chord versus position on the airfoil surface for various roughnesses and angle of attack. A table of power law curve fits of Nusselt number as a function of Reynolds number is also provided. The higher level of turbulence in the IRT versus flight had little effect on heat transfer for the lower Reynolds numbers but caused a moderate increase in heat transfer at the higher Reynolds numbers. Turning on the cloud making spray air in the IRT did not alter the heat transfer. Roughness generally increased the heat transfer by locally disturbing the boundary layer flow. Finally, the present data was not only compared with previous airfoil data where applicable, but also with leading edge cylinder and flat plate heat transfer values which are often used to estimate airfoil heat transfer in computer codes.

Poinsatte, Philip E.↗
NASA NTRS1989

Spaceborne radar observations: A guide for Magellan radar-image analysis

Geologic analyses of spaceborne radar images of Earth are reviewed and summarized with respect to detecting, mapping, and interpreting impact craters, volcanic landforms, eolian and subsurface features, and tectonic landforms. Interpretations are illustrated mostly with Seasat synthetic aperture radar and shuttle-imaging-radar images. Analogies are drawn for the potential interpretation of radar images of Venus, with emphasis on the effects of variation in Magellan look angle with Venusian latitude. In each landform category, differences in feature perception and interpretive capability are related to variations in imaging geometry, spatial resolution, and wavelength of the imaging radar systems. Impact craters and other radially symmetrical features may show apparent bilateral symmetry parallel to the illumination vector at low look angles. The styles of eruption and the emplacement of major and minor volcanic constructs can be interpreted from morphological features observed in images. Radar responses that are governed by small-scale surface roughness may serve to distinguish flow types, but do not provide unambiguous information. Imaging of sand dunes is rigorously constrained by specific angular relations between the illumination vector and the orientation and angle of repose of the dune faces, but is independent of radar wavelength. With a single look angle, conditions that enable shallow subsurface imaging to occur do not provide the information necessary to determine whether the radar has recorded surface or subsurface features. The topographic linearity of many tectonic landforms is enhanced on images at regional and local scales, but the detection of structural detail is a strong function of illumination direction. Nontopographic tectonic lineaments may appear in response to contrasts in small-surface roughness or dielectric constant. The breakpoint for rough surfaces will vary by about 25 percent through the Magellan viewing geometries from low to high Venusian latitudes. Examples of anomalies and system artifacts that can affect image interpretation are described.

Ford, J. P.↗
NASA NTRS1989

LIMEX '87 ice surface characteristics - Implications for C-band SAR backscatter signatures

Ice surface characterization data collected in 1987, during the Labrador Sea Ice Margin Experiment, are analyzed to estimate the changes in snow and ice properties at the onset of melt. Surface measurements were made from an ice research vessel on several days (some of which had coincident remote-sensing flights) at a number of locations in the marginal ice zone. These data are used as input parameters in a simple scattering model to simulate the effects of variations in material properties upon C-band scattering signatures. Snow moisture and large-scale surface roughness are demonstrated to have the largest effect upon HH polarization scattering cross-section sigma(HH)(O) and large differences are predicted between undeformed floe surfaces and deformed or undulating rough ice surfaces. Using a parametric approach, an approximate picture of rough and smooth ice signatures and their relative contrast are provided. The models reproduce a trend observed in synthetic aperture radar (SAR) images of increasing backscatter contrast between deformed and underformed ice over an early period of warning: such observations are consistent with the results of analysis of SAR images to date. The model also reproduces a calibrated SAR-derived signature with a reasonable degree of accuracy.

Drinkwater, Mark R.↗