Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Optical properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Examining the Impact of Overlying Aerosols on the Retrieval of Cloud Optical Properties from Passive Remote Sensing

Haywood et al. (2004) show that an aerosol layer above a cloud can cause a bias in the retrieved cloud optical thickness and effective radius. Monitoring for this potential bias is difficult because space ]based passive remote sensing cannot unambiguously detect or characterize aerosol above cloud. We show that cloud retrievals from aircraft measurements above cloud and below an overlying aerosol layer are a means to test this bias. The data were collected during the Intercontinental Chemical Transport Experiment (INTEX-A) study based out of Portsmouth, New Hampshire, United States, above extensive, marine stratus cloud banks affected by industrial outflow. Solar Spectral Flux Radiometer (SSFR) irradiance measurements taken along a lower level flight leg above cloud and below aerosol were unaffected by the overlying aerosol. Along upper level flight legs, the irradiance reflected from cloud top was transmitted through an aerosol layer. We compare SSFR cloud retrievals from below ]aerosol legs to satellite retrievals from the Moderate Resolution Imaging Spectroradiometer (MODIS) in order to detect an aerosol ]induced bias. In regions of small variation in cloud properties, we find that SSFR and MODIS-retrieved cloud optical thickness compares within the uncertainty range for each instrument while SSFR effective radius tend to be smaller than MODIS values (by 1-2 microns) and at the low end of MODIS uncertainty estimates. In regions of large variation in cloud properties, differences in SSFR and MODIS ]retrieved cloud optical thickness and effective radius can reach values of 10 and 10 microns, respectively. We include aerosols in forward modeling to test the sensitivity of SSFR cloud retrievals to overlying aerosol layers. We find an overlying absorbing aerosol layer biases SSFR cloud retrievals to smaller effective radii and optical thickness while nonabsorbing aerosols had no impact.

Coddington, O. M.↗

Effect of the Temperature of Photonic Annealing on the Structural and Optical Properties of ZnO Films Synthesized by Dual Magnetron-Assisted Sputtering

Zinc-oxide films 1.4 μm in thickness are deposited onto glassy substrates by the dual magnetron-assisted sputtering of zinc targets in an argon and oxygen gas atmosphere. The dependences of the structural and optical characteristics of the ZnO films on the temperature of postdeposition photonic annealing are studied. It is established that an increase in the annealing temperature yields an increase in the degree of crystallinity of the films. Electron microscopy shows that the deposited ZnO coatings are columnar in structure and the microstructure density and crystallite size increase upon annealing. It is found that, at an annealing temperature of 450–650°C, the optical transmittance increases to >90% in the spectral range 400–1100 nm. The experimental results show that the temperature of vacuum photonic annealing has the most profound effect on the final properties of ZnO coatings.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Arctic Biogeochemical and Optical Properties of Dissolved Organic Matter Across River to Sea Gradients

Arctic landscapes are warming and becoming wetter due to changes in precipitation and the timing of snowmelt which consequently alters seasonal runoff and river discharge patterns. These changes in hydrology lead to increased mobilization and transport of terrestrial dissolved organic matter (DOM) to Arctic coastal seas where significant impacts on biogeochemical cycling can occur. Here, we present measurements of dissolved organic carbon (DOC) and chromophoric DOM (CDOM) in the Yukon River-to-Bering Sea system and two river plumes on the Alaska North Slope which flow into the Beaufort Sea. Our sampling characterized optical and biogeochemical properties of DOM during high and low river discharge periods for the Yukon River-Bering Sea system. The average DOC concentration at the multiple Yukon River mouths ranged from a high of 10.36 mg C L-1 during the ascending limb of the 2019 freshet (late May), 6.4 mg C L-1 during the descending limb of the 2019 freshet (late June), and a low of 3.86 mg C L-1 during low river discharge in August 2018. CDOM absorption coefficient at 412 nm (aCDOM(412)) averaged 8.23 m-1, 5.07 m-1, and 1.9 m-1, respectively. Several approaches to model DOC concentration based on its relationship with CDOM properties demonstrated cross-system seasonal and spatial robustness for these Arctic coastal systems despite spanning an order of magnitude decrease in DOC concentration from the lower Yukon River to the Northern Bering Sea as well as the North Slope systems. “Snapshot” fluxes of DOC and CDOM across the Yukon River Delta to Norton Sound were calculated from our measurements and modeled water fluxes forced with upstream USGS river gauge data. Our findings suggest that during high river flow, DOM reaches the delta largely unaltered by inputs or physical and biogeochemical processing and that the transformations of Yukon River DOM largely occur in the plume. However, during low summer discharge, multiple processes including local precipitation events, microbial decomposition, photochemistry, and likely others can alter the DOM properties within the lower Yukon River and Delta prior to flowing into Norton Sound.

Arctic↗

Influence of Oxygen Flow and Stoichiometry on Optical Properties and Damage Resistance of Hafnium Oxide Thin Films

Hafnium oxide (HfO 2 ) is predominantly used as a high-index material in multi-layer dielectric coatings for high-peak- and high-average-power lasers, but laser damage often initiates within the HfO 2 layers despite their wide bandgap. Oxygen deficiency during deposition can introduce vacancy-related sub-bandgap states and absorptive defects, lowering damage resistance. This study investigates how oxygen flow during HfO 2 deposition with ion beam sputtering (IBS) affects its stoichiometry, defect formation, and nanosecond laser-induced damage threshold (LIDT) and whether single-layer trends predict multilayer performance. Single layers were deposited at varying oxygen flows, characterized for optical and structural properties, and tested for the LIDT at 1064 nm and 355 nm. Increasing oxygen flow drove the layer toward near-stoichiometric HfO 2 , reduced the refractive index, and altered the density of surface pinhole-like features. The single-layer LIDT at 355 nm increased with oxygen, whereas the 1064 nm LIDT was comparatively less sensitive to oxygen flow, consistent with the wavelength-dependent roles of absorptive precursors and microstructural defects. In contrast, a HfO 2 -based high-reflector (HR) showed a higher LIDT at lower oxygen flow, indicating that the family of damage precursors changes between single layers and multilayers; in stacks, structural properties such as stress, gas entrapment and thermal dissipation may outweigh the isolated absorptive defects found in single layers. These results demonstrate that the optimal oxygen flow condition depends on both LIDT wavelength and film architecture. We identified, for single layers, a 15–35 sccm window for maximizing the 1064 nm LIDT and a high-flow optimum (45 sccm) for the 355 nm LIDT and, for 355 nm HR stacks, a distinct lower-flow regime (~10 sccm).

Optics and optical instruments↗

Syntheses, structures, magnetism, and optical properties of gadolinium scandium chalcogenides

Three gadolinium scandium chalcogenides have been synthesized using Sb{sub 2}Q{sub 3} (Q=S, Se) fluxes at 975 deg. C. Gd{sub 3.04}Sc{sub 0.96}S{sub 6}, GdScS{sub 3}, and Gd{sub 1.05}Sc{sub 0.95}Se{sub 3} are crystallized in U{sub 3}ScS{sub 6} type, GdFeO{sub 3} type, and UFeS{sub 3} type structures, respectively. The magnetic susceptibilities for these compounds follow the Curie-Weiss law above their transition temperatures. The effective magnetic moments are close to calculated values for free Gd{sup 3+} ions. The Weiss constants for Gd{sub 3.04}Sc{sub 0.96}S{sub 6}, GdScS{sub 3}, and Gd{sub 1.05}Sc{sub 0.95}Se{sub 3} are determined to be -3.3(1), -4.5(4), and 1.5(1) K, respectively. Gd{sub 3.04}Sc{sub 0.96}S{sub 6} orders antiferromagnetically below 9 K. GdScS{sub 3} exhibits an antiferromagnetic ordering below 3 K with a weak ferromagnetism. Gd{sub 1.05}Sc{sub 0.95}Se{sub 3} undergoes a ferromagnetic transition around 5 K. The optical band gaps for Gd{sub 3.04}Sc{sub 0.96}S{sub 6}, GdScS{sub 3}, and Gd{sub 1.05}Sc{sub 0.95}Se{sub 3} are 1.5, 2.1, and 1.2 eV, respectively. - Graphical abstract: A view of the three-dimensional structure of Gd{sub 3.04}Sc{sub 0.96}S{sub 6} along the c axis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Unique signatures of the Rashba effect in the magneto-optical properties of two-dimensional semiconductors

Herein, the authors theoretically demonstrate two simple magneto-optical measurements which can be used to confirm the existence of Rashba terms in two dimensional semiconductors, even in samples of unoptimal quality, where the transition line widths are comparable to or larger than the Landau level splitting. The first is magnetic circular dichroism (MCD), where a giant MCD signal should be observed at the band edge in the presence of Rashba terms. The second is the comparison of the diamagnetic shift measured in absorption with that in photoluminescence which occurs from the dispersion minimum of the Rashba exciton.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Optical properties of the Si-doped GaN/Al{sub 2}O{sub 3} films

Morphological and optical studies of the Si-doped GaN films (doping level N{sub Si} = 1.5 x 10{sup 19} cm{sup -3}) grown by vapor-phase epitaxy from metalorganic compounds on a sapphire substrate oriented along the c axis are conducted. For the grown GaN films, the following characteristics are obtained: energy of electron transition E{sub 0}, absorption coefficient {alpha}, refractive index n, and frequencies of transverse and longitudinal optical lattice vibrations characteristic of the crystalline GaN films.

36 MATERIALS SCIENCE↗

Optical properties of particles in planetary atmospheres - Laboratory studies

The laboratory techniques employed for the determination of optical constants are discussed briefly. The values obtained for the real n and imaginary k parts of the refractive indices of water, ice, and liquid ammonia are presented graphically. Work currently in progress on solid ammonia and on sulphuric acid is discussed. Other approaches to studies of the properties of aerosols in planetary atmospheres are presented briefly.

Williams, D.↗

Accounting for the Complex Surface Structure in Ellipsometric Studies of the Effects of Magnetron Sputtering Modes on the Growth and Optical Properties of In{sub 2}O{sub 3} Films

The efficiency of invoking additional information on optical transmission in solving the inverse problem of ellipsometry by a minimization method is demonstrated in practice for In{sub 2}O{sub 3} fi doped and nondoped with Sn on Al{sub 2}O{sub 3} (012) substrates. This approach allows the thickness and refractive index of thin films with rough surfaces to be uniquely determined. Solutions of the inverse problem in the framework of one-, two-, and multilayer models are compared. The last provides the best description of the experimental data and the correct parameters of the samples. The dependences of the investigated properties of films produced with different magnetron sputtering modes are found using the above methods and models and do not contradict general concepts about the film formation by this material.

36 MATERIALS SCIENCE↗

Changes in optical properties of the Surveyor 3 camera

The measurements made to analyze changes in the camera's optical performance involved the following areas: (1) spectral reflectance (specular), (2) gonioreflectance, (3) ellipsometry, (4) spectral transmission, (5) contrast and modulation transfer, and (6) photography (macro and micro).

Rennilson, J.↗

Microscopic theory of optical properties of composite media with chaotically distributed nanoparticles

The boundary problem of light reflection and transmission by a film with chaotically distributed nanoinclusions is considered. Based on the proposed microscopic approach, analytic expressions are derived for distributions inside and outside the nanocomposite medium. Good agreement of the results with exact calculations and (at low concentrations of nanoparticles) with the integral Maxwell-Garnett effective-medium theory is demonstrated. It is shown that at high nanoparticle concentrations, averaging the dielectric constant in volume as is done within the framework of the effective-medium theory yields overestimated values of the optical film density compared to the values yielded by the proposed microscopic approach. We also studied the dependence of the reflectivity of a system of gold nanoparticles on their size, the size dependence of the plasmon resonance position along the wavelength scale, and demonstrated a good agreement with experimental data. (photonics and nanotechnology)

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

The effects of cerium doping on the size, morphology, and optical properties of α-hematite nanoparticles for ultraviolet filtration

Highlights: • Possible application of cerium-doped α-hematite as ultraviolet filter. • Nanoparticles obtained through co-precipitation technique using various cerium doping levels followed by annealing. • Comprehensive materials characterisation utilizing XRD, DSC/TGA, STEM, UV–vis spectroscopy. • Increasing cerium content reduces particle sizing and alters morphology. • Solubility of cerium in hematite seen between 5 and 10% doping, 10% cerium doping greatly enhances attenuation in ultraviolet region and increases optical bandgap. - Abstract: Metal oxide nanoparticles have potential use in energy storage, electrode materials, as catalysts and in the emerging field of nanomedicine. Being able to accurately tailor the desirable properties of these nanoceramic materials, such as particle size, morphology and optical bandgap (E{sub g}) is integral in the feasibility of their use. In this study we investigate the altering of both the structure and physical properties through the doping of hematite (α-Fe{sub 2}O{sub 3}) nanocrystals with cerium at a range of concentrations, synthesised using a one-pot co-precipitation method. This extremely simple synthesis followed by thermal treatment results in stable Fe{sub 2−x}Ce{sub x}O{sub y} nanoceramics resulting from the burning of any unreacted precursors and transformation of goethite-cerium doped nanoparticle intermediate. The inclusion of Ce into the crystal lattice of these α-Fe{sub 2}O{sub 3} nanoparticles causes a significantly large reduction in mean crystalline size and alteration in particle morphology with increasing cerium content. Finally we report an increase optical semiconductor bandgap, along with a substantial increase in the ultraviolet attenuation found for a 10% Ce-doping concentration which shows the potential application of cerium-doped hematite nanocrystals to be used as a pigmented ultraviolet filter for cosmetic products.

36 MATERIALS SCIENCE↗

Electrical and optical properties of Sn doped CuInO{sub 2} thin films: Conducting atomic force microscopy and spectroscopic ellipsometry studies

Tin doped CuInO{sub 2} thin films deposited by rf magnetron sputtering technique show columnar structure with (006) preferred orientation. Conducting atomic force microscopy measurements show the presence of nanoconductivity regions when the current flow direction is along the in-plane InO{sub 6} layer and absence of conducting regions when the current direction is along O-Cu-O layers perpendicular to the film surface. The strong anisotropy observed in the electrical properties of tin doped samples is due to the preferred crystallite orientation and highly anisotropic delafossite structure. A large change in the electrical conductivity value and activation energy value in undoped films and tin doped samples has also been explained in terms of change in crystallite orientation on doping. Spectroscopic ellipsometry measurements have been used to determine the optical constant and dielectric function of CuInO{sub 2} and CuInO{sub 2}:Sn films and show a band gap value of 4.5 eV in tin doped samples due to removal of structural defects.

36 MATERIALS SCIENCE↗

Comparison of Aerosol Optical Properties and Water Vapor Among Ground and Airborne Lidars and Sun Photometers During TARFOX

We compare aerosol optical thickness (AOT) and precipitable water vapor (PWV) measurements derived from ground and airborne lidars and Sun photometers during TARFOX (Tropospheric Aerosol Radiative Forcing Observational Experiment). Such comparisons are important to verify the consistency between various remote sensing measurements before employing them in any assessment of the impact of aerosols on the global radiation balance. Total scattering ratio and extinction profiles measured by the ground-based NASA/GSFC Scanning Raman Lidar (SRL) system, which operated from Wallops Island, Virginia (37.86 deg N, 75.51 deg W), are compared with those measured by the Lidar Atmospheric Sensing Experiment (LASE) airborne lidar system aboard the NASA ER-2 aircraft. Bias and rms differences indicate that these measurements generally agreed within about 10%. Aerosol extinction profiles and estimates of AOT are derived from both lidar measurements using a value for the aerosol extinction/backscattering ratio S(sub a)=60 sr for the aerosol extinction/backscattering ratio, which was determined from the Raman lidar measurements.

Ferrare, R.↗

Comparison of Aerosol Optical Properties and Water Vapor Among Ground and Airborne Lidars and Sun Photometers During TARFOX

We compare aerosol optical thickness (AOT) and precipitable water vapor (PWV) measurements derived from ground and airborne lidars and sun photometers during the Tropospheric Aerosol Radiative Forcing Observational Experiment. Such comparisons are important to verify the consistency between various remote sensing measurements before employing them in any assessment of the impact of aerosols on the global radiation balance. Total scattering ratio and extinction profiles measured by the ground-based NASA Goddard Space Flight Center scanning Raman lidar system, which operated from Wallops Island, Virginia (37.86 deg N, 75.51 deg W); are compared with those measured by the Lidar Atmospheric Sensing Experiment (LASE) airborne lidar system aboard the NASA ER-2 aircraft. Bias and root-mean-square differences indicate that these measurements generally agreed within about 10%. Aerosol extinction profiles and estimates of AOT are derived from both lidar measurements using a value for the aerosol extinction/backscattering ratio S(sub a) = 60 sr for the aerosol extinction/backscattering ratio, which was determined from the Raman lidar measurements. The lidar measurements of AOT are found to be generally within 25% of the AOT measured by the NASA Ames Airborne Tracking Sun Photometer (AATS-6). However, during certain periods the lidar and Sun photometer measurements of AOT differed significantly, possibly because of variations in the aerosol physical characteristics (e.g., size, composition) which affect S(sub a). Estimates of PWV, derived from water vapor mixing ratio profiles measured by LASE, are within 5-10% of PWV derived from the airborne Sun photometer. Aerosol extinction profiles measured by both lidars show that aerosols were generally concentrated in the lowest 2-3 km.

Ferrare, R.↗

Short-Range Order Tunes Optical Properties in Long-Range Disordered ZnSnN2-ZnO Alloy

Local site ordering offers a new paradigm for property control in functional materials. However, systems that exhibit a propensity for local order and global disorder are often challenging to characterize, and demonstrations of ordering-induced property tuning are few and far between. Here, we demonstrate that short-range ordering tunes the optical absorption edge in the long-range disordered alloy system (ZnSnN2)1-x(ZnO)2x at x = 0.25. We use combinatorial cosputtering to synthesize a set of thin-film samples spanning this alloy space. X-ray diffraction demonstrates lattice contraction as a function of alloy composition, confirming that a mixed-anion and -cation alloy has been synthesized. Using N and O K-edge X-ray absorption near-edge structure in conjunction with simulations of cation-disordered supercell structures, we find that samples exhibit octet-rule-breaking motifs around both anions. Upon annealing at an alloy composition of x = 0.25, X-ray absorption analysis suggests that local motif structure shifts toward octet-rule-conserving while long-range disorder is maintained. Spectroscopic ellipsometry reveals that local ordering increases the absorption edge energy at constant composition. Additionally, alloy-induced optical absorption edge tuning is demonstrated. This work paves the way toward property tuning with short-range ordering in (ZnSnN2)1-x(ZnO)2x and beyond.

36 MATERIALS SCIENCE↗