Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Manufacturing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Preliminary Study on Machining of Additively Manufactured Ti-6Al-4V

We report additively manufactured metals differ from their conventionally produced counterparts due to the inherent material inhomogeneity, porosity, and thermal stress induced by the process. These differences make the machining of additively manufactured metals more difficult and cause premature tool failure or unexpected surface finish at certain conditions. This study takes the first step to investigate and identify the causes of these issues, particularly for Ti-6Al-4V. Printed and wrought samples, as well as heat treatment effect, are compared in a dry cutting condition at a cutting speed of 90 m/min in terms of cutting power, vibration, temperature, and produced surface finish. The results show a lower cutting power and more vibration for as-printed Ti samples, indicating a less ductile microstructure and inclusion of pores. Heat treatment can eliminate these phenomena. There is no significant difference found in the produced surface finish at the current cutting condition.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Process-Structure Linkages Using a Data Science Approach: Application to Simulated Additive Manufacturing Data

A novel data science workflow is developed and demonstrated to extract process-structure linkages (i.e., reduced-order model) for microstructure evolution problems when the final microstructure depends on (simulation or experimental) processing parameters. Our workflow consists of four main steps: data pre-processing, microstructure quantification, dimensionality reduction, and extraction/validation of process-structure linkages. These methods that can be employed within each step vary based on the type and amount of available data. In this paper, this data-driven workflow is applied to a set of synthetic additive manufacturing microstructures obtained using the Potts-kinetic Monte Carlo (kMC) approach. Additive manufacturing techniques inherently produce complex microstructures that can vary significantly with processing conditions. Using the developed workflow, a low-dimensional data-driven model was established to correlate process parameters with the predicted final microstructure. In addition, the modular workflows developed and presented in this work facilitate easy dissemination and curation by the broader community.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Predicting Sintering Window of Binder Jet Additively Manufactured Parts Using a Coupled Data Analytics and CALPHAD Approach

Batch-to-batch variation in powder compositions for binder jet additive manufacturing (BJAM) can significantly deter defining an “ideal” sintering window for a given alloy. One way to overcome the problem is by running sintering experiments at various temperatures for each batch of the powder. However, such an approach increases the time required to achieve large-scale production of parts. The predictive capabilities of computational thermodynamic tools like CALPHAD can be leveraged to overcome the challenge, especially for binder jet additive manufacturing, since the process occurs under near-equilibrium conditions. However, calculating the sintering window using CALPHAD can be computationally expensive, considering many possible feedstock compositions within “specification”. Here, we generate high throughput CALPHAD data for nickel-based superalloys to develop machine learning models to predict the sintering window rapidly. The predictive capability of the models has been validated using published results on BJAM of Inconel 718 and 625. Further, validated models are lightweight and can be deployed in an industrial setting to get sintering window in an accelerated manner.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Ordered indices of the production structure of manufacturing systems based on an information-theoretic approach

The production structure of a manufacturing system not only influences its transportation and operation cost, but also affects logistics and parts/machine assignment decisions. Based on the sending and feedback mechanisms of information, the principles of conditional entropy and classical probability are utilized to establish structure entropy models and ordered indices of the system with dynamic characteristics and generality, which provide effective solutions for the absence of quantitative method in evaluating the structural optimization of production system. In an empirical study, this paper analyzes different production structures when workpieces are processed by different working routes before and after the implementation of cellular manufacturing. Afterwards, the developed structure entropy models and ordered indices are utilized to calculate the orderliness of production structure under the two different states. The final result verifies well the validity of this quantitative method for evaluating the orderliness of production structures.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2019

Achieving high strength and ductility in traditionally brittle soft magnetic intermetallics via additive manufacturing

Intermetallic alloys possess exceptional soft magnetic properties, including high permeability, low coercivity, and high saturation induction, but exhibit poor mechanical properties that make them impractical to bulk process and use at ideal compositions. We used laser-based Additive Manufacturing to process traditionally brittle Fe–Co and Fe–Si alloys in bulk form without macroscopic defects and at near-ideal compositions for electromagnetic applications. The binary Fe–50Co, as a model material, demonstrated simultaneous high strength (600–700 MPa) and high ductility (35%) in tension, corresponding to a ~300% increase in strength and an order-of-magnitude improvement in ductility relative to conventionally processed material. Atomic-scale toughening and strengthening mechanisms, based on engineered multiscale microstructures, are proposed to explain the unusual combination of mechanical properties. Here, this work presents an instance in which metal Additive Manufacturing processes are enabling, rather than limiting, the development of higher-performance alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dynamic properties of 316l stainless steel repaired using electron beam additive manufacturing

Additive manufacturing has the potential to be used for repair of high-value parts, but the strength and integrity of such repaired parts, especially under dynamic loading, in still unknown. This work presents the results of high strain-rate dynamic testing of additively repaired stainless steel samples. The 316L samples were intentionally damaged and subsequently repaired with 308L stainless steel wire using electron beam additive manufacturing. The repaired samples were subjected to gas-gun impact testing to induce incipient damage and determine the role played by the repaired region in dictating damage and failure. The results show the following: 1) the equation of state of the repaired region is comparable to the original material as shown by the unchanged spall plane location, 2) the deformation behavior is similar to the original material as shown by the similar Hugoniot Elastic limit, 3) the spall strength of the repaired region is slightly higher than the original material due to varying grain size, and 4) the damage morphology in the repaired region is different and involves a high rate of void coalescence. In conclusion, despite these minor differences in the spall strength and the damage morphology, the overall dynamic response of the original material and repaired samples is similar suggesting that AM is a promising approach for repairing high-value components.

36 MATERIALS SCIENCE↗
DOE OSTI2023

On the strength and fracture toughness of an additive manufactured CrCoNi medium-entropy alloy

An additively manufactured (nominally equiatomic) CrCoNi alloy was processed by laser powder bed fusion (LPBF). At ambient temperatures (298 K), this medium-entropy alloy displayed a yield strength, σ y of ~691 ± 9 MPa, and an ultimate tensile strength, σ u of ~926 ± 15.2 MPa; at cryogenic temperatures (77 K), yield and tensile strengths increased respectively to σ y ~ 944 ± 6 MPa and σ u ~ 1382 ± 11 MPa. These strength levels are 57 and 44% higher than that of the wrought alloy, due to strengthening from the solidification cellular structures intertwined with dislocations in the LPBF CrCoNi. The crack-initiation fracture toughness, K JIc was measured to be ~183.7 ± 28 MPa√m at 298 K; this value marginally decreased by ~4% to ~176 ± 11 MPa√m at 77 K. These K JIc values of the LPBF CrCoNi were 11% and 35% lower than the wrought CrCoNi alloy at 298 K and 77 K, respectively. Here, the resistance to crack growth of the LPBF CrCoNi from its hierarchical micro- and meso-structures was evaluated using nonlinear-elastic fracture mechanics by measuring R-curve behavior in the form of the J-integral as a function of crack extension. The specific features of the hierarchical microstructures at different length-scales provide a basis for the strengthening and toughening properties of this additively manufactured medium-entropy alloy. This correlation between the deformation and the hierarchical microstructures at different length-scales may provide future guidance for improving the fracture toughness properties of medium-entropy alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Large-scale additive manufacturing tooling for extrusion-compression molds

Carbon fiber reinforced polymer composites (CFPC) have been used in additive manufacturing (AM) due to both the high-strength-to-weight and superior-stiffness-to-weight ratios. CF AM is being considered for tooling applications. In AM, CFPCs are usually aligned along the deposition direction; however, it results in anisotropic thermal properties which affect the heat transfer and warpage of the final part. In this study, three male molds with different infill patterns were produced via the material extrusion additive manufacturing (EDF-AM) process. These include (a) 0°: infill pattern along the printing direction; (b) 90°: infill pattern perpendicular to the printing direction; and (c) 0°/90°: alternate layers along and perpendicular directions. The effect of the infill pattern on thermal conductivity was analyzed and observed that 0° infill (surface temperature: 79.2°C) had the highest conductivity; and 90° infill (surface temperature: 66.4°C) had the least.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Evolution of global and local deformation in additively manufactured octet truss lattice structures

Additively manufactured lattice truss structures, often referred to as architected cellular materials, present significant advantages over conventional structures due to their unique characteristics such as high strength-to-weight ratios and surface area-to-volume ratios. These geometrically complex structures, however, come with concomitant challenges for qualification and inspection. In this study, compression testing interrupted with micro-computed tomography inspection was conducted to monitor the evolution of global and local deformation throughout the loading process of 304L stainless steel octet truss lattice structures. Both two- and three-dimensional image analysis techniques were leveraged to characterize geometric heterogeneities resulting from the laser powder bed fusion manufacturing process as well as track the structure throughout deformation. Variations from model-predicted behavior resulting from these heterogeneities are considered relative to the predicted and actual responses of the structures during compression to better understand, model, and predict the octet truss lattice structure compression response.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mitigating keyhole pore formation by nanoparticles during laser powder bed fusion additive manufacturing

Keyhole pore formation is one of the most detrimental subsurface defects in the laser metal additive manufacturing process. However, effective ways to mitigate keyhole pore formation beyond tuning laser processing conditions during keyhole mode laser melting are still lacking. Here we report a novel approach to mitigate keyhole pore formation during laser powder bed fusion (LPBF) process by using stable nanoparticles. The critical keyhole depth for keyhole pore generation (i.e., the largest keyhole depth without keyhole pore formation) during LPBF of Al6061 increases from 246 µm to 454 µm (85% increase) after adding TiC nanoparticles. In-depth x-ray imaging studies and thermo-fluid dynamics simulation enable us to identify that two mechanisms work together to mitigate keyhole pore generation: (1) adding nanoparticles prevents the keyhole from collapsing by increasing the liquid viscosity to impede the protrusion development; (2) adding nanoparticles slows down the keyhole pore movement by increasing the liquid viscosity, resulting in the recapturing of the pore by the keyhole. We further demonstrate that adding TiC nanoparticles can also eliminate the keyhole fluctuation induced keyhole pore during LPBF of Al6061. Our research provides a potential way to mitigate keyhole pore formation for defect lean metal additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Verification and validation of a rapid heat transfer calculation methodology for transient melt pool solidification conditions in powder bed metal additive manufacturing

A fundamental understanding of spatial and temporal thermal distributions is crucial for predicting solidification and solid-state microstructural development in parts made by additive manufacturing. While sophisticated numerical techniques that are based on finite element or finite volume methods are useful for gaining insight into these phenomena at the length scale of the melt pool (100 - 500 µm), they are ill-suited for predicting engineering trends over full part cross-sections (> 10 x 10 cm) or many layers over long process times (> many days) due to the necessity of fully resolving the heat source characteristics. On the other hand, it is extremely difficult to resolve the highly dynamic nature of the process using purely in-situ characterization techniques. This article proposes a pragmatic alternative based on a semi-analytical approach to predicting the transient heat conduction during powder bed metal additive manufacturing process. The model calculations were theoretically verified for selective laser melting of AlSi10Mg and electron beam melting of IN718 powders for simple cross-sectional geometries and the transient results are compared to steady state predictions from the Rosenthal equation. It is shown that the transient effects of the scan strategy create significant variations in the melt pool geometry and solid-liquid interface velocity, especially as the thermal diffusivity of the material decreases and the pre-heat of the process increases. With positive verification of the strategy, the model was then experimentally validated to simulate two point-melt scan strategies during electron beam melting of IN718, one intended to produce a columnar and one an equiaxed grain structure. Lastly, through comparison of the solidification conditions (i.e. transient and spatial variations of thermal gradient and liquid-solid interface velocity) predicted by the model to phenomenological CET theory, the model accurately predicted the experimental grain structures.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Security of additive manufacturing: Attack taxonomy and survey

Additive manufacturing (AM) is a rapidly growing, multibillion dollar industry. AM is increasingly being used to manufacture functional parts, including components of safety critical systems in aerospace, automotive, and other industries. This makes AM an attractive attack target. AM Security is a fairly new field of research that addresses this novel threat. Here, this paper serves dual purposes: For researchers just entering AM security, we provide an in-depth introduction to this highly multi-disciplinary research field. And, for active researchers in the field, this paper provides a comprehensive, structured survey of the state of the art as well as our proposal for attack taxonomies.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Infiltration studies of additive manufacture of WC with Co using binder jetting and pressureless melt method

Additive manufacturing (AM) of tungsten carbide-cobalt (WC-Co) is explored starting with WC preforms shaped with binder jet additive manufacturing (BJAM) followed by melt infiltration of Co. The research objective is to demonstrate the ability to net-shape WC-Co composites through BJAM of a WC preform followed by backfilling with cobalt via pressureless infiltration. This method also has the potential to minimize shrinkage and grain growth compared to other AM techniques. The effects of sintering, Co content, and infiltration time on the net shaping and properties of processed composites are shown. The best shaped material had an average grain size of 5.1 μm, 32 vol.% Co, density of 98.54% theoretical, fracture toughness of 23.2 MPa m 1/2 , and hardness of 9.0 GPa. Data presented illustrates that the proposed approach results in favorable ceramic-metal (cermet) properties and is viable for fabricating cermets of other material combinations. Furthermore successful AM of cermets provides complex geometries, high throughout, and low costs.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Extrusion control for high quality printing on Big Area Additive Manufacturing (BAAM) systems

Big Area Additive Manufacturing (BAAM) is a large format additive manufacturing (AM) process. The size scale has enabled many new applications for AM. However, at this scale, lack of high print resolution and extruder flowrate control lead to potentially significant geometric deviations in the printed part. This paper examines strategies to improve geometric quality in BAAM parts. Multi-resolution printing, extrusion diversion, and feedforward extruder control are examined herein. Furthermore, these methods were all found to be effective in mitigating phenomena detrimental to geometric part quality on the BAAM process.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Heterogeneities dominate mechanical performance of additively manufactured metal lattice struts

Architected structural metamaterials, also known as lattice, truss, or acoustic materials, provide opportunities to produce tailored effective properties that are not achievable in bulk monolithic materials. These topologies are typically designed under the assumption of uniform, isotropic base material properties taken from reference databases and without consideration for sub-optimal as-printed properties or off-nominal dimensional heterogeneities. However, manufacturing imperfections such as surface roughness are present throughout the lattices and their constituent struts create significant variability in mechanical properties and part performance. Here, this study utilized a customized tensile bar with a gauge section consisting of five parallel struts loaded in a stretch (tensile) orientation to examine the impact of manufacturing heterogeneities on quasi-static deformation of the struts, with a focus on ultimate tensile strength and ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2019

The effects of material anisotropy on secondary processing of additively manufactured CoCrMo

Components produced by near net shape additive manufacturing processes often require subsequent subtractive finishing operations to satisfy requisite surface finish and geometric tolerances. It is well established that the microstructure and properties of the as-built component are sensitive to the additive processing history. Therefore, downstream secondary processes may be affected by the as-built components’ mechanical behavior. In this work we study the sensitivity of secondary machining operations on CoCrMo samples produced via laser powder bed fusion. Utilizing novel high-throughput mechanical testing, microstructure characterization, and a rigorous statistical analysis we investigate the degree of material anisotropy present in the as-built material. We then study the effects of this anisotropy on secondary processing via slot milling experiments. Our results indicate that mechanical anisotropy is driven by both the morphology of the microstructure as well as crystallographic texture. Furthermore, the machining force response is correspondingly sensitive to these sources of anisotropy, which has the potential to impact how manufacturers finish additively built parts.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Toward large-scale simulation of residual stress and distortion in wire and arc additive manufacturing

In this study, we aim to advance the structural analysis of wire and arc additive manufacturing (WAAM) by considering the thermomechanical features inherent in direct energy deposition. Simulation approaches including the iterative substructure method (ISM), dynamic mesh refining method (DMRM), and graphics processing unit (GPU) based explicit finite element method (FEM) were developed for accelerating additive manufacturing stress analysis that is very time consuming by conventional numerical methods. ISM and DMRM take advantage of the strong nonlinearity phenomenon near the moving heat source by reducing the global iterations and refining the local mesh, respectively. In addition to the use of GPUs, the explicit FEM is accelerated by a time scaling technique based on the inherent strain concept. The residual stress and distortion of two large builds were analyzed, showing very consistent numerical results and good agreement with experiments. Compared with the commercial software Abaqus, the novel approaches reduced the computational cost substantially without compromising accuracy. The GPU code showed the highest computational efficiency (30~70×), while DMRM and ISM had acceleration factors of 9× and 3×, respectively. Finally, such high-fidelity modeling approaches will be very useful for building up a digital twin of WAAM to reduce development time and cost.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mechanical Characterization of High-Temperature Carbon Fiber-Polyphenylene Sulfide Composites for Large Area Extrusion Deposition Additive Manufacturing

Additive manufacturing (AM) is evolving from rapid prototyping to production of structural components. The widespread application of AM demands a high level of mechanical performance from these components, and it is therefore essential to improve feedstock material in order to meet these mechanical expectations. However, compared to traditional manufacturing techniques, the mechanical properties of AM materials and their resulting components are not well understood. In this study, we investigated the processability, microstructure, and mechanical performance of twin-screw compounded short carbon fiber reinforced polyphenylene sulfide (PPS) pellets as a feedstock material for big area AM (BAAM). The performance of the AM components was compared to that of traditional processing methods, namely injection molding (IM) and extrusion-compression molding (ECM). It was found that the AM composites exhibited 118% lower tensile strength and 55% lower tensile modulus when compared to traditional injection molding composite specimens; however, AM composites exhibited comparable properties to ECM composites. This response was attributed to highly aligned fibers in IM and AM samples. However, the AM composites contained porosity (15.5% volume), which reduced their mechanical properties in comparison to ECM composites. Finally, the IM process showed the maximum amount of fiber attrition with minimum porosity (0.007% volume), while the ECM process exhibited the least fiber attrition with 4.3% volume porosity.

36 MATERIALS SCIENCE↗