Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Injection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Energy distributions of superthermal ions in regime with sawtooth oscillations during neutral beam injection at the Globus-M tokamak

Specific features of the energy distributions of fast ions during neutral beam injection at the Globus-М tokamak are considered. Different loss mechanisms that can lead to the formation of a specific shape of the energy spectrum of superthermal ions are analyzed. The effect of sawtooth oscillations on the loss of fast ions is discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Injection photodiodes based on low-resistivity ZnS single crystals

Results of an experimental study of Ni-n-n{sup +}-In photodiode structures fabricated from a low-resistivity ZnS:Al crystal (n{sup +}-region) are reported. The high-resistivity compensated n-type layer is produced by thermal diffusion of silver. The photodiodes exhibit an injection amplification of the photocurrent under a forward bias of 1-10 V. The dependence of the currents through the diodes on the thickness of the n-type layer in the dark and under UV irradiation is determined. The photosensitivity is at a maximum in the fundamental absorption range in a narrow spectral band.

36 MATERIALS SCIENCE↗

Spin injection in GaAs/GaSb quantum-well heterostructures

GaAs/GaSb type-II quantum-dot heterostructures were grown by molecular-beam epitaxy. The circularly polarized photoluminescence of these samples in a magnetic field up to 4.7 T in the Faraday configuration was investigated. It was found that the emission from quantum dots in a magnetic field is {sigma}{sup -}-polarized, which corresponds to the electron-spin component along the magnetic-field vector of +1/2. The degree of polarization increases with increasing excitation intensity. The observed effect is explained in terms of spin injection from the GaSb matrix, where spin orientation appears owing to the Zeeman splitting of the conduction band. An increase in the degree of polarization occurs due to a reduction in the charge-carrier radiative lifetime in type-II quantum dots with increasing excitation level.

36 MATERIALS SCIENCE↗

Minority-charge-carrier mobility at low injection level in semiconductors

From the kinetic equations, the distribution functions for majority and minority charge carriers are obtained at a low injection level. For describing the electron-hole collisions, the Landau collision integral is used. The carrier scattering at ionized or neutral impurity and at acoustic phonons is taken into account. The majority-carrier distribution function is presented in the analytical form. The minority-carrier mobility is calculated and analyzed, and the features of its behavior at low temperatures are revealed. It follows from the developed theory that the hole mobility in an n-type material increases with doping and neutral-impurity concentration. This effect is attributed to mutual charge-carrier collisions and different effective masses of different-sign carriers.

36 MATERIALS SCIENCE↗

Dependence of the carrier concentration on the current in mid-infrared injection lasers with quantum wells

The current dependences of spontaneous luminescence in mid-IR injection lasers with InGaAsSb/InAlGaAsSb quantum wells are experimentally studied in the subthreshold and lasing modes. The current dependence of the carrier concentration is determined using the current dependence of the total spontaneous luminescence. A lack of carrier concentration saturation with current in the lasing mode was observed. It is shown that this can be due to carrier heating at low quantum-confinement levels and an increase in light absorption by free holes in the waveguide.

36 MATERIALS SCIENCE↗

On the limit of the injection ability of silicon p{sup +}–n junctions as a result of fundamental physical effects

Analytical expressions describing the dependences of the p{sup +}–n-junction leakage current on the doping level of the p{sup +}-type region are derived by taking into account a whole set of nonlinear physical effects: electron–hole scattering, Auger recombination, band-gap narrowing, and nonlinear dependences of the charge-carrier lifetime and mobility on the doping level. It is shown that the dependence for the leakage current has a minimum at which the injection ability of the p{sup +}-type emitter is at a maximum. The dependence of the extremum position on the main parameters of the heavily doped p{sup +} layer is analyzed. The data obtained make it possible to optimize the structure of high-power silicon devices and to facilitate the adequacy of numerical calculations.

36 MATERIALS SCIENCE↗

Field Effect in PbSnTe:In Films with Low Conductivity in the Mode of Injection from Contacts and Space-Charge Limitation of the Current

At T = 4.2 K, a strong change (up to 4 times) in the space-charge-limited current (SCLC) is observed for the first time at samples based on semi-insulating PbSnTe:In films grown by molecular-beam epitaxy on BaF{sub 2}(111) substrates. The obtained results agree with experiments on the effect of treatment of the surface of PbSnTe:In films on the space-charge-limited current with a variation in the current to 10{sup 3} times or more. At a qualitative level, the model is considered which assumes the substantial contribution of localized surface states to space charge formed in the mode of space-charge-limited current due to the injection of charge carriers from contacts.

36 MATERIALS SCIENCE↗

Terahertz Injection Lasers Based on a PbSnSe Solid Solution with an Emission Wavelength up to 50 μm and Their Application in the Magnetospectroscopy of Semiconductors

On the basis of a Pb{sub 1–x}Sn{sub x}Se solid solution, long-wavelength diffusion injection lasers with laser generation up to a record long wavelength of 50.4 μm are created and studied. Pb{sub 1–x}Sn{sub x}Se single crystals are grown from the vapor phase under the conditions of free growth (unseeded vapor-growth technique). By the example of a HgCdTe narrow-gap semiconductor and a quantum-well heterostructure, the possibility of applying the developed lasers in solid-state spectroscopy is demonstrated.

36 MATERIALS SCIENCE↗

The influence of intake flow and coolant temperature on gasoline spray morphology during early-injection DISI engine operation

Multi-hole gasoline injectors operating at conditions spanning throttled early-intake stroke operation produce spray plumes that either remained separated or merge and collapse due to flash boiling. Flash boiling occurs due to the sudden expansion of gas bubbles in the liquid fuel at high fuel temperature and low ambient pressure. This study records high-speed images of spray-morphology changes due to in-cylinder flow, thereby revealing operating conditions that do and do not affect the self-induced morphology observed in quiescent vessels. Specifically, in a central-injection, four-valve, high-tumble engine, where the thermodynamic state and in-cylinder cross flow are dynamic. Motivated by cold start and hot restart operation, the fuel pressure, coolant temperature, in-cylinder air pressure, and engine rpm were systematically varied over relevant operating conditions, which bracketed the range from non- to flash-boiling sprays. The results reveal the operating conditions at which the in-cylinder cross flow disrupts the spray morphology as well as the extent of the disruption. At 650 rpm, the spray morphology was similar to that observed in quiescent vessels at nominally equivalent fuel temperature and in-cylinder pressure, indicating that the spray’s self-induced entrainment flow dominated the in-cylinder flow. However, for fuel temperature and ambient pressure near the transition between non- and flash-boiling, the intake cross flow at higher engine speed (1950 rpm) significantly disrupted the spray morphology. The high cross-flow velocity appears to induce plume merging and collapse, whereas none was evident at low rpm (650 rpm). This study led to the postulate that the spray merging and collapse are governed by the rate of atomization near the nozzle exit, presumed to be controlled by either or both aerodynamic atomization and flash-boiling intensity. It would then follow that spray modeling in CFD requires atomization models that blend the effects of both physical processes.

42 ENGINEERING↗

Fallon, NV FORGE well 21-31 Lithology, Mineral, Image Log, and Injection Test data

Attached is 5 datasets collected from Fallon FORGE well 21-31 located in Churchill County, Nevada collected and interpreted between Feburary 2018-January 2020. This submission includes 1) new lithology interpretation derived from petrographic thin sections of sidewall cores taken from well 21-31, 2) X-Ray Diffraction (XRD) interpretation of sidewall cores and cuttings from well 21-31, 3) Hyperspectral (Short-Wave Infrared and Long-Wave Infrared) interpretation of cuttings and sidewall cores from well 21-31, 4) Interpretation of Formation MicroImager (FMI) and Borehole Televiewer (BHTV) image logs for natural fractures and induced structures for well 21-31, 5) Injection test data and associated analytical model parameters from well testing of well 21-31.

15 GEOTHERMAL ENERGY↗

Utah FORGE: Fault Reactivation Through Fluid Injection Induced Seismicity Laboratory Experiments

Included are results from shear reactivation experiments on laboratory faults pre-loaded close to failure and reactivated by the injection of fluid into the fault. The sample comprises a single-inclined-fracture (SIF) transecting a cylindrical sample of Westerly granite. All experiments are conducted at ambient temperature and follow a similar protocol: (i) application of confining stresses (3MPa) on the fault fully saturated with DI water, (ii) shear-mobilization through the increase of axial loading at a constant displacement rate until a post-peak steady-state condition is reached, (iii) reduction of axial loading and related shear stress to a prescribed fraction of the peak steady-state frictional strength (typically 60% to 90%, representing intermediate to high magnitudes) and (iv), fault reactivation triggered by a stepwise increase of pore pressure on the fault in 0.1 MPa increments held constant for 1-5 minutes. Mechanical data from three ISCO pumps connected to a Temco pressure vessel measure axial, confining, and fault-related parameters, including fluid pressure (kPa), fluid flow rate (mL/min), and axial displacement (mm). See included code for initial data analysis and visualization for select experiments. Resource names represent experiment numbers found in the "Read Me" file, which describes each experimental setup and parameters.

15 GEOTHERMAL ENERGY↗

Materials for High-Pressure Fuel Injection Systems

The high-level goal of this multi-year effort was to facilitate the Advanced Combustion Engine goal of 20% improvement (compared to 2009 baseline) of commercial engine efficiency by 2015. A sub-goal is to increase the reliability of diesel fuel injectors by investigating modelbased scenarios that cannot be achieved by empirical, trial and error methodologies alone. During this three-year project, ORNL developed the methodology to evaluate origins and to record the initiation and propagation of fatigue cracks emanating from holes that were electrodischarge machined (EDM), the method used to form spray holes in fuel injector tips. Both x-ray and neutron-based methods for measuring residual stress at four different research facilities were evaluated to determine which, if any, was most applicable to the fuel injector tip geometry. Owing to the shape and small volumes of material involved in the sack area, residual stress data could only be obtained in the walls of the nozzle a few millimeters back from the tip, and there was a hint of only a small compressive stress. This result was consistent with prior studies by Caterpillar. Residual stress studies were suspended after the second year, reserving the possibility of pursuing this in the future, if and when methodology suitable for injector sacks becomes available. The smooth specimen fatigue behavior of current fuel injector steel materials was evaluated and displayed a dual mode initiation behavior. At high stresses, cracks started at machining flaws in the surface; however, below a critical threshold stress of approximately 800 MPa, cracks initiated in the bulk microstructure, below the surface. This suggests that for the next generation for high-pressure fuel injector nozzles, it becomes increasingly important to control the machining and finishing processes, especially if the stress in the tip approaches or exceeds that threshold level. Fatigue tests were also conducted using EDM notches in the gage sections. Compared to the smooth specimens, EDM notching led to a severe reduction in total fatigue life. A reduction in fatigue life of nearly four orders of magnitude can occur at an EDM notch the approximate size of fuel injector spray holes. Consequently, the initiation and propagation behavior of cracks from small spray holes is relevant for generation of design quality data for the next generation diesel fuel injection devices. This is especially true since the current design methodologies usually rely on the less conservative smooth specimen fatigue testing results, and since different materials can have varying levels of notch fatigue resistance.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Application of Vacancy Injection Gettering to Improve Efficiency of Solar Cells Produced by Millinet Solar (CRADA Final Report)

NREL will apply vacancy injection gettering (VIG) to Millinet solar cells and evaluate the performance improvement produced by this process step. The VIG will be done in conjunction with the formation of a back, Al-alloyed, contact. Millinet Solar will provide NREL with cells having AR coating on the front side and screen-printed Al on the backside, which will be processed in the NREL's optical furnace to perform simultaneous VIG and back contact alloying with deep BSF. These cells will be sent back to Millinet solar for a screen-printed front/side contact mask, followed by a second firing at NREL. Detailed analyses will be performed to determine improvements due to BSF and VIG.

14 SOLAR ENERGY↗

Preliminary Failure Modes and Effects Analysis of the US Massive Gas Injection Disruption Mitigation System Design

This report presents the results of a preliminary failure modes and effects analysis (FMEA) of a candidate design for the ITER Disruption Mitigation System. This candidate is the Massive Gas Injection System that provides machine protection in a plasma disruption event. The FMEA was quantified with “generic” component failure rate data as well as some data calculated from operating facilities, and the failure events were ranked for their criticality to system operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mechanistic Studies of Charge Injection from Metallic Electrodes into Organic Semiconductors Mediated by Ionic Functionalities (Final Report)

Metal-organic semiconductor interfaces are important because of their ubiquitous role in determining the performance of modern electronics such as organic light emitting diodes (OLEDs), fuel cells, batteries, field effect transistors (FETs), and organic solar cells. Interfaces between metal electrodes required for external wiring to the device and underlying organic structures directly affect the charge carrier injection/collection efficiency in organic-based electronic devices primarily due to the mismatch between energy levels in the metal and organic semiconductor. Environmentally stable and cost-effective electrode materials, such as aluminum and gold typically exhibit high potential barriers for charge carriers injection into organic devices leading to increased operational voltages in OLEDs and FETs and reduced charge extraction in photovoltaic devices. This leads to increased power consumption by the device, reduced overall efficiency, and decreased operational lifetime. These factors represent a significant obstacle for development of next generation of cheap and energy-efficient components based on organic semiconductors.

36 MATERIALS SCIENCE↗

System Study: High-Pressure Safety Injection 1998–2012

This report presents an unreliability evaluation of the high-pressure safety injection system (HPSI) at 69 U.S. commercial nuclear power plants. Demand, run hours, and failure data from fiscal year 1998 through 2012 for selected components were obtained from the Equipment Performance and Information Exchange (EPIX). The unreliability results are trended for the most recent 10 year period while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the HPSI results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

System Study: High-Pressure Coolant Injection 1998-2012

This report presents an unreliability evaluation of the high-pressure coolant injection system (HPCI) at 69 U.S. commercial nuclear power plants. Demand, run hours, and failure data from fiscal year 1998 through 2012 for selected components were obtained from the Equipment Performance and Information Exchange (EPIX). The unreliability results are trended for the most recent 10 year period while yearly estimates for system unreliability are provided for the entire active period. No statistically significant increasing or decreasing trends were identified in the HPCI results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗