SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Experiments were performed to determine the skin friction and heat transfer behavior of antimisting kerosene (AMK) in pipe flows. The additive used was FM-9. Based on the results of the experiments, which identify high viscosity and viscoelasticity for AMK, it is recommended that AMK be degraded. Sufficient degradation produces behavior similar to that of jet A.
Low Cr steels AISI 41410, AISI 4340, and high Cr austenitic stainless steels AISI 304, AISI 316 were ion nitrided in a dc glow discharge plasma consisting of a 75 percent H2 - 25 percent N2 mixture. Surface compound layer phases were identified, and compound layer microhardness and diffusion zone microhardness profiles were established. Distinct differences in surface compound layer hardness and diffusion zone profiles were determined between the low and high Cr alloy steels. The high Cr stainless steels after ion nitriding displayed a hard compound layer and an abrupt diffusion zone. The compound layers of the high Cr stainless steels had a columnar structure which accounts for brittleness when layers are exposed to contact stresses. The ion nitrided surfaces of high and low Cr steels displayed a low coefficient of friction with respect to the untreated surfaces when examined in a pin and disk tribotester.
This paper deals with the stability of limit cycles (Steady-State Oscillations) associated with the multi-degree-of-freedom model of a frictionally damped and aerodynamically unstable rotor stage. By using the first order averaging technique, a generalized criterion has been established to sort out those unstable limit cycles which govern the maximum transient amplitude beyond which the rotor stage becomes unstable.The stability of the remaining steady-state solutions is analyzed by linearizing the averaged system of differential equations. Numerical results are discussed for three-, four- and five-bladed disks.
The design and performance of a small belt-type skin-friction gage to measure wall shear-stress coefficients in wind-tunnel testing are described, summarizing the report of Vakili and Wu (1982). The sensor employs a flexible belt of variable surface characteristics; this belt, wrapped tightly around two cylinders mounted on frictionless flexures, is equipped with strain gages to estimate the deflection of the belt by the flow. An alternative approach uses IR illumination, optical fibers, and a photosensitive transistor, permitting direct measurement of the belt deflection. Drawings, diagrams, and graphs of sample data are provided.
The laser interferometric skin friction meter was used to measure wall shear stress distributions in two interactions of fin-generated swept shock waves with turbulent boundary layers. The basic research configuration was an unswept sharp-leading-edge fin of variable angle mounted on a flatplate. The results indicate that such measurements are practical in high-speed interacting flows, and that a repeatability of + or - 6 percent or better is possible. Marked increases in wall shear were observed in both swept interactions tested.
A method was evolved to account for the effects of compressibility in flows through long circular pipes of uniform diameter. Velocity and density variations across the flow cross section were approximated by profile shapes recommended for a flow past flat plates. The wall of the pipe was assumed to have attained an adiabatic condition. An integral method was used to obtain solutions for the governing equations of flow. The method was then used to analyze the detailed pressure measurements made in a long pipe for flow of air at different flow rate settings. Flow friction values derived from these pressure measurements were compared with the standard incompressible pipe flow data available in existing literature.
The oil-film method of skin friction measurement, which does not require calibration, nevertheless entails that interferometric measurements of the oil film be obtained. The oil-film method is presently simplified by eliminating interferometry and its requisite polished surface, by taking direct and dynamic measurements of the oil-film slope with a small position-sensing photodiode. This technique has undergone verification in incompressible turbulent and laminar flows in flat-plate boundary layers and pipe flows; the meter is judged to be inexpensive, simple, and robust.
It has previously been shown that the no-slip boundary conditions leads to a singularity at a moving contact line and that this presumes some form of slip. Present considerations on the energetics of slip due to shear stress lead to a yield stress boundary condition. A model for the distortion of the liquid state near solid boundaries gives a physical basis for this boundary condition. The yield stress condition is illustrated by an analysis of a slender drop rolling down an incline. That analysis provides a formula for the frictional drag resisting the drop movement. With the present boundary condition, the length of the slip region becomes a property of the fluid flow.
A friction factor model is developed for the entrance-region of a duct. The model is used in an annular gas seal analysis similar to Nelson's (1984). Predictions of the analysis are compared to experimental results for a smooth-stator/smooth-rotor seal and three honeycomb-stator/smooth-rotor seals. The model predicts a leakage and direct damping well. The model overpredicts the dependence of cross-coupled stiffness on fluid prerotation. The model predicts direct stiffness poorly.
An investigation is conducted of application of optimal observer-based control laws derived using both pole-placement techniques and optimal linear regulator theory. Although a pole-placement-derived control law with optimal observer provides fast response and excellent noise rejection, its observer requires an electrical input proportional to the unknown skin friction force, which is unavailable. To overcome this limitation, an optimal linear regulator design is proposed which estimates the unknown force input and provides excellent noise rejection, at the expense, however, of significantly slower transient response.
Report presents results of experimental study of friction and wear in unlubricated sliding of silicon-based ceramics on Inconel(R) 718 nickel-based alloy. Both monolithic and fiber-reinforced ceramics tested at temperatures from 25 to 800 degrees C. Evaluates ceramic materials for potential use as cylinder liners, piston caps, and other engine parts subjected to sliding or rubbing.
Precise hinge rotates with minimal friction and without "slop". Axis of rotation at central axis of concentric, self-retaining assembly. Blades in same plane, and both edges of blades and apexes of grooves lie along same line, allowing free rotation without either binding or slop. Blades on rotor engage grooves on stator. Blades pivot about edges through arc defined by slotted openings in stator housing.
This paper describes a new high temperature friction and wear test apparatus (tribometer) at NASA Lewis Research Center, Cleveland, Ohio. The tribometer can be used as a pin-on-disk or pin-on-ring configuration and is specially designed to measure the tribological properties of ceramics and high temperature metallic alloys from room temperature to 1200 C. Sliding mode can be selected to be either unidirectional at velocities up to 22 m/sec or oscillating at frequencies up 4.5 Hz and amplitudes up to + or - 60 deg. The test atmosphere is established by a controlled flow rate of a purge gas. All components within the test chamber are compatible with oxidizing, inert, or reducing gases.
There is a need for information on runways which may become slippery due to various forms and types of contaminants. Experience has shown that since the beginning of all weather aircraft operations, there have been landing and aborted takeoff incidents and/or accidents each year where aircraft have either run off the end or veered off the shoulder of low friction runways. NASA Langley's Landing and Impact Dynamics Branch is involved in several research programs directed towards obtaining a better understanding of how different tire properties interact with varying pavement surface characteristics to produce acceptable performance for aircraft ground handling requirements. One such effort, which was jointly supported by not only NASA and the FAA but by several aviation industry groups including the Flight Safety Foundation, is described.
A process for reducing skin friction, inhibiting the effects of liquid turbulence, and decreasing heat transfer in a system involving flow of a liquid along a surface of a body includes applying a substantially integral sheet of a gas, e.g., air, immediately adjacent to the surface of the body; a marine vehicle, which has a longitudinally grooved surface in proximity with the liquid and with a surface material having high contact angle between the liquid and said wall to reduce interaction of the liquid; water, with the surface of the body; and the hull of the marine vehicle.
A model is developed for lattice-mismatched epitaxial layers, which makes it possible to calculate both the equilibrium critical thickness as well as the kinetic rate of misfit accommodations. The technique for calculating the equilibrium critical thickness is similar to that of Matthews (1966) in that it uses the force balance approach and the Volterra description of the dislocation line. For the kinetic component of misfit accommodation, the model uses a dynamic frictional force. A simple criterion is proposed for determining whether the generation of misfit dislocations will be controlled by the equilibrium or the kinetic factors.
Cavendish balance adapted to new purpose. Apparatus developed which measures forces of adhesion and friction between specimens of solid materials in vacuum at temperatures from ambient to 900 degrees C. Intended primarily for use in studying adhesion properties of ceramics and metals, including silicon carbide, aluminum oxide, and iron-base amorphous alloys.
The authors present numerical experiments on dynamical friction in pairs of elliptical galaxies of unequal mass. They confirm that the self-gravity of the response is not important and show the drastic effect of the deformability of the companion which reduces the decay time by more than a factor of 2. Almost the same amount of orbital energy is dissipated within the satellite as within the large galaxy. Finally, the authors discuss the importance of distant encounters for the dynamical evolution of systems of galaxies.