Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EROSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Environmental aspects of run-off and siltation in the Anacostia basin from hyperaltitude photographs

The effects of urbanization and highway construction on run-off, erosion and siltation on the Anacostia watershed was analyzed. The analysis was based on changes in land use patterns demonstrated by aerial photographs, geologic and hydrologic data. Subwatersheds were studied in terms of three hypothetical storms of different magnitudes. An approximately 10 percent increase in impervious surface can cause a 12 percent increase in peak discharge for storms of the magnitude of tropical storm Agnes, a 20 percent increase for a 10 hour storm and a 150 percent increase for a thunderstorm. The early discharge from a storm of Agnes' magnitude can be increased by 100 percent. Corresponding effects were observed in soil erosion and siltation from bare construction sites. These effects are interrelated with sewage, oil, and chemical pollution and inadequate public transportation. The net result is steady degradation of the local environment, the estuary and the bay.

Ealy, C. D.↗

A proposed origin of the Olympus Mons escarpment

Olympus Mons (Nix Olympica) on Mars is delimited by a unique steep, nearly circular scarp. A pyroclastic model is proposed for the construct's origin. It is postulated that the Olympus Mons plateau is constructed predominantly of numerous ash-flow tuffs which were erupted from central sources over an extended period of time. Lava flows may be intercalated with the tuffs. A schematic radial profile incorporating the inferred compaction zones for an ash sheet is proposed. Following emplacement, eolian (and possibly fluvial) erosion and abrasion during dust storms would act on the ash sheets. Interior portions of the sheets would spall and slump following eolian erosion, generating steep, relatively smooth boundary scarps. The scarp would be circular due to symmetrical distribution of compaction zones. The model implies further that the Olympus Mons plateau rests on a more resistant rock substrate.

King, J. S.↗

An explanation for Iapetus' asymmetric reflectance

Cook and Franklin (1970) consider Iapetus originally to have been coated with about a meter of ice. They suggest that Iapetus' orbital velocity about Saturn has caused an asymmetric erosion of this ice layer which has now nearly laid bare its 'leading' hemisphere, but not as yet the entire 'trailing' hemisphere. Rather than an erosion process which operates more actively on the leading side, this paper considers an ice deposition mechanism operating more actively on the trailing side. The two main assumptions used are (1) that there are more icy than rocky meteoroids in Saturn's environment, and (2) that some portion of each icy meteoroid will stick to a surface at collision velocities less than 2.4 km per sec, but will completely vaporize itself at greater velocities. A meteoroid can have the minimum collision velocity of about 1.7 km per sec with Iapetus only if their velocity vectors are nearly parallel, and under these conditions such collisions would tend to be with the trailing hemisphere. Collisions with the leading hemisphere will tend to be at a much higher velocity.

Peterson, C.↗

Modification of premare impact craters by volcanism and tectonism

Many lunar craters greater than 10 km in diameter exhibit a variety of morphological characteristics which are not produced by meteorite impact or meteorite erosion. Most such craters are located in or near the margins of the maria. Although some could have resulted from processes such as cauldron resurgence, caldera formation, or ring dike emplacement, most have formed by modification of impact craters by endogenic processes including erosion by flowing lava, fissure volcanism, plutonism, and uplift of crater floors along ring fractures of impact origin.

Brennan, W. J.↗

Present and potential land use mapping in Mexico

The Mexican Water Plan (MWP) conducted studies of present and potential land use in Mexico using LANDSAT-1 satellite imagery. Present land use studies were carried out all over the country (197 million hectares); nine soil uses were mapped according to the first classification level recommended by the U.S. Geological Survey. Also 6.3 million hectares of land with advanced erosion were detected. Work was executed at a rate of 8 million hectares per month; reliability was 90% and the cost of only 0.1 cents/hectare. The potential land use study was performed in 45 million hectares at a rate of 4 million hectares per month and at a cost of 0.33 cents/hectare. Soil units according to FAO classification were delineated scale 1:1 million; interpretative maps were also prepared dealing with potential agricultural productivity carrying capacity for cattle, water, erosion risk, and slope ranges.

Garduno, H.↗

Solid rocket motor nozzles

The steps in the nozzle design process are examined. The nozzle designer's role in defining design requirements and constraints is included along with discussions of each of the three basic phases of the nozzle design process itself: (1) aerodynamic design, in which the gas-contacting surfaces are configured to produce the required performance within the envelope limits; (2) thermal design, in which termal liners and thermal insulators are selected and configured to maintain the surfaces as closely as practical against effects of erosion and to limit the structure temperature to acceptable levels; and (3) structural design, in which materials are selected and configured to support the thermal components and to sustain the predicted loads. Analytical techniques that are used to establish thermal and structural design integrity and to predict nozzle performance are discussed along with methods for nozzle quality assurance. Emphasis is placed on nozzle design and materials for modern high-temperature aluminized propellants. Recurring nozzle design problems of graphite cracking and ejection, differential erosion at material interfaces, lack of sufficient proven nondestructive testing (NDT) techniques, the uncertainty of adhesive bonding, and inadequate definition of material properties, particularly at high temperatures are considered.

Ellis, R. A.↗

Dynamics of turbidity plumes in Lake Ontario

The author has identified the following significant results. Large turbidity features along the 275 km south shore of Lake Ontario were analyzed using LANDSAT-1 images. The Niagara River plume, ranging from 30 to 500 sq km in area is, by far, the largest turbidity feature in the lake. Based on image tonal comparisons, turbidity in the Welland Canal is usually higher than that in any other water course discharging into the lake during the shipping season. Less turbid water enters the lake from the Port Dalhousie diversion channel and the Genesee River. Relatively clear water resulting from the deposition of suspended matter in numerous upstream lakes is discharged by the Niagara and Oswego Rivers. Plume analysis corroborates the presence of a prevailing eastward flowing longshore current along the entire south shore. Plumes resulting from beach erosion were detected in the images. Extensive areas of the south shore are subject to erosion but the most severely affected beaches are situated between Fifty Mile Point, Ontario and Thirty Mile Point, New York along the Rochester embayment, and between Sodus Bay and Nine Mile Point.

Pluhowski, E. J.↗

Effect of thermal cycling in a Mach 0.3 burner rig on properties and structure of directionally solidified gamma/gamma prime-delta eutectic

An experimental study was carried out to evaluate the effect of cyclic thermal exposures on the mechanical properties of a gamma/gamma prime-delta eutectic alloy parallel to the growth direction. The alloy had a nominal composition by weight of Ni-20 Nb-6 Cr-2.5 Al and was directionally solidified at 3 cm/hr in a furnace with a thermal gradient of at least 200 C/cm. Bars of the alloy were exposed in a Mach 0.3 burner rig and cycled 300 times between 1100 and 425 C. Oxidation-erosion characteristics of the alloy were determined by weight loss measurements at 300-cycle intervals. After cyclic exposure, stress rupture and tensile tests were performed at both 760 and 1040 C. Microstructural changes from cyclic exposure were determined. Thermal cycling resulted in gamma prime coarsening and Widmanstaetten delta precipitation in the gamma phase. An unidentified precipitate, presumably gamma prime, was observed within the delta phase. These microstructural changes did not affect the mechanical properties of the eutectic. High oxidation-erosion weight loss rate was observed.

Gray, H. R.↗

The effect of vertical distortion in the modeling of sedimentation phenomena - Martian crater wake streaks

Theoretical mass flow rate and the particle trajectory equations of motion of granular material in saltation are used to correlate experimental data for the rate of erosion in the wake regions of wind-tunnel-model Martian craters. Vertical geometric distortion is inherent in the simulation because of the equivalent roughness height characteristic of a turbulent boundary layer, which is affected by material in saltation. It is thus necessary to distort topographic model geometry in the vertical direction. A systematic similitude which is based on erosion rate and equivalent roughness in saltation is shown to correlate time-dependent model data as long as the model Reynolds number is higher than a critical value.

Iversen, J. D.↗

High-power and 2.5 kW advanced-technology ion thruster

Investigations for improving ion thruster components in the 30 cm engineering model thruster (EMT) resulted in the demonstration of useful techniques for grid short removal and discharge chamber erosion monitoring, establishment of relationships between double ion production and thruster operating parameters, verification of satisfactory specifications on porous tungsten vaporizer material and barium impregnated porous tungsten inserts, demonstration of a new hollow cathode configuration, and specification of magnetic circuit requirements for reproducing desired magnetic mappings. The capacity of a 30 cm EMT to operate at higher beam voltages and currents (higher power) was determined. Operation at 2 A beam current and higher beam voltage is shown to be essentially equivalent to operation at 1.1 kV with regard to efficiency, lifetime and operating conditions. The only additional requirement is an improvement in high voltage insulation and propellant isolator capacity. Operation at minimum voltage and higher beam currents is shown to increase thruster discharge chamber erosion in proportion to beam current. Studies to find alternatives to molybdenum for manufacturing ion optics grids are also reported.

Poeschel, R. L.↗

Development of a plasma sprayed ceramic gas path seal for high pressure turbine applications

The plasma sprayed graded layered yittria stabilized zirconia (ZrO2)/metal(CoCrAlY) seal system for gas turbine blade tip applications up to 1589 K (2400 F) seal temperatures was studied. Abradability, erosion, and thermal fatigue characteristics of the graded layered system were evaluated by rig tests. Satisfactory abradability and erosion resistance was demonstrated. Encouraging thermal fatigue tolerance was shown. Initial properties for the plasma sprayed materials in the graded, layered seal system was obtained, and thermal stress analyses were performed. Sprayed residual stresses were determined. Thermal stability of the sprayed layer materials was evaluated at estimated maximum operating temperatures in each layer. Anisotropic behavior in the layer thickness direction was demonstrated by all layers. Residual stresses and thermal stability effects were not included in the analyses. Analytical results correlated reasonably well with results of the thermal fatigue tests. Analytical application of the seal system to a typical gas turbine engine application predicted performance similar to rig specimen thermal fatigue performance. A model for predicting crack propagation in the sprayed ZrO2/CoCrAlY seal system was proposed, and recommendations for improving thermal fatigue resistance were made. Seal system layer thicknesses were analytically optimized to minimize thermal stresses in the abradability specimen during thermal fatigue testing. Rig tests on the optimized seal configuration demonstrated some improvement in thermal fatigue characteristics.

Shiembob, L. T.↗

Improved high pressure turbine shroud

A new high pressure turbine shroud material has been developed from the consolidation of prealloyed powders of Ni, Cr, Al and Y. The new material, a filler for cast turbine shroud body segments, is called Genaseal. The development followed the identification of oxidation resistance as the primary cause of prior shroud deterioration, since conversion to oxides reduces erosion resistance and increases spalling under thermal cycled engine conditions. The NICrAlY composition was selected in preference to NIAL and FeCRALY alloys, and was formulated to a prescribed density range that offers suitable erosion resistance, thermal conductivity and elastic modulus for improved behavior as a shroud.

Bessen, I. I.↗

An endurance test of a 900 series 30-cm engineering model ion thruster

The 10,000 hour endurance test of the first engineering model 30-cm thruster (S/N 701) identified discharge chamber erosion as a life limiting problem. Modifications to minimize this problem have been implemented in the 900 series thrusters. This paper describes a test conducted to evaluate the success of these modifications. The post-test analysis results of thruster 701 are summarized and the erosion reducing modifications described. Test results for thruster 901 up to 4165 hours, when the test was interrupted by a shorted wire, are described. The conclusions of a post-test examination of thruster 901 are included. Also being evaluated was a thermal vacuum breadboard SCR series inverter power processor which is described.

Collett, C. R.↗

Rocketdyne's advanced coal slurry pumping program

The Rocketdyne Division of Rockwell International Corporation is conducting a program for the engineering, fabrication, and testing of an experimental/prototype high-capacity, high-pressure centrifugal slurry feed pump for coal liquefaction purposes. The abrasion problems in a centrifugal slurry pump are primarily due to the manner in which the hard, solid particles contained in the slurry are transported through the hydraulic flow passages within the pump. The abrasive particles can create scraping, grinding, cutting, and sandblasting effects on the various exposed parts of the pump. These critical areas involving abrasion and impact erosion wear problems in a centrifugal pump are being addressed by Rocketdyne. The mechanisms of abrasion and erosion are being studied through hydrodynamic analysis, materials evaluation, and advanced design concepts.

Davis, D. E.↗

Dust storms on Mars: Considerations and simulations

Aeolian processes are important in modifying the surface of Mars at present, and appear to have been significant in the geological past. Aeolian activity includes local and global dust storms, the formation of erosional features such as yardangs and depositional features such as sand dunes, and the erosion of rock and soil. As a means of understanding aeolian processes on Mars, an investigation is in progress that includes laboratory simulations, field studies of earth analogs, and interpretation of spacecraft data. This report describes the Martian Surface Wind Tunnel, an experimental facility established at NASA-Ames Research Center, and presents some results of the general investigation. Experiments dealing with wind speeds and other conditions required for the initiation of particle movement on Mars are described and considerations are given to the resulting effectiveness of aeolian erosion.

Greeley, R.↗

Paleohydraulics and hydrodynamics of Scabland floods

The last major episode of scabland flooding (approx. 18,000-13,000 years B.P.) left considerable high-water mark evidence in the form of: (1) eroded channel margins; (2) depositional features; (3) ice-rafter erratics; and (4) divide crossings. These were used to reconstruct maximum flood stages and water-surface gradients. Engineering hydraulic calculation procedures allowed the analyses of flood discharges and mean velocities from these data. Secondary flow phenomena, including various forms of vortices and flow separations, are considered to have been the principal erosive processes. The intense pressure and velocity gradients of vortices along the irregular channel boundaries produced the plucking-type erosion.

Baker, V. R.↗

Erosion/corrosion of turbine airfoil materials in the high-velocity effluent of a pressurized fluidized coal combustor

Four candidate turbine airfoil superalloys were exposed to the effluent of a pressurized fluidized bed with a solids loading of 2 to 4 g/scm for up to 100 hours at two gas velocities, 150 and 270 m/sec, and two temperatures, 730 deg and 795 C. Under these conditions, both erosion and corrosion occurred. The damaged specimens were examined by cross-section measurements, scanning electron and light microscopy, and X-ray analysis to evaluate the effects of temperature, velocity, particle loading, and alloy material. Results indicate that for a given solids loading the extent of erosion is primarily dependent on gas velocity. Corrosion occurred only at the higher temperature. There was little difference in the erosion/corrosion damage to the four alloys tested under these severe conditions.

Zellars, G. R.↗

Origin of the stepped topography of the Martian poles

Ablation and condensation of water vapor are suggested as the principal factors responsible for the circumpolar layered and stepped terrain found at the North and South Poles of Mars. A metastable erosion rate due to decreasing albedo and increasing radiation input caused by dust deposits on the steeper slopes of the ablating layered deposits provides a mechanism for the development of the stepped topography. Loose excess dust accumulated during scarp ablation may then be removed by wind erosion.

Howard, A. D.↗