SEARCH · Engineering Papers

Results for “Drag coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

All sources NASA NTRS DOE OSTI

NASA NTRS1999

Nacelle/Diverter Integration into the Design Optimization Process Using Pseudo, Warped, and Real Nacelles

The computational results of the optimized complete configurations, including nacelles and diverters, are presented in terms of drag count improvement compared with the TCA baseline configuration at Mach 2.4, C(sub L)=0.1. The three candidate designs are designated by the organization from which they were derived. ARC represents the Ames Research Center 1-03 design, BCAG represents the Boeing Commercial Aircraft Group's design from Seattle, and BLB represents the design from Boeing Long Beach. All CFD methods are in unanimous agreement that the Ames 1-03 configuration has the largest performance improvement, followed closely by the BCAG configuration, with a much smaller improvement attained by Boeing Long Beach. The Ames design was obtained using the single-block wing/body code SYN87-SB with its "pseudo" nacelle option-an elaborate technique for incorporating nacelle/diverter effects into the design optimization process. This technique uses AIRPLANE surface pressure coefficient data with and without the nacelles/diverters. Further details of this method are described. It is reasonable to expect that further improvements could be achieved by including the "real" nacelles directly into the optimization process by use of the newly-developed multiblock optimization code, SYN107-MB, which can handle full configurations.

Cliff, Susan E.↗

NASA NTRS1989

Feasibility of generating an artificial burst in a turbulent boundary layer, phase 2

Various drag accounts for about half of the total drag on commercial aircraft at subsonic cruise conditions. Two avenues are available to achieve drag reduction: either laminar flow control or turbulence manipulation. The present research deals with the latter approach. The primary objective of Phase 2 research was to investigate experimentally the feasibility of substantially reducing the skin-friction drag in a turbulent boundary layer. The method combines the beneficial effects of suction and a longitudinally ribbed surface. At a sufficiently large spanwise separation, the streamwise grooves act as a nucleation site causing a focusing of low-speed streaks over the peaks. Suction is then applied intermittently through longitudinal slots located at selected locations along those peaks to obliterate the low-speed regions and to prevent bursting. Phase 2 research was divided into two tasks. In the first, selective suction from a single streamwise slot was used to eliminate either a single burst-like event or a periodic train of artificially generated bursts in laminar and turbulent boundary layers that develop on a flat plate towed in a water channel. The results indicate that equivalent values of the suction coefficient as low as 0.0006 were sufficient to eliminate the artificially generated bursts in a laminar boundary layer.

Gad-El-hak, Mohamed↗

NASA NTRS1996

Uncertainty Analysis for Oil-Film Interferometry Skin-Friction Measurement Techniques

Over the past 20 years, the use of oil-film interferometry to measure the skin friction coefficient (C(sub f) = tau/q where tau is the surface shear stress and q is the dynamic pressure) has increased. Different forms of this oil-film technique with various levels of accuracy and ease of use have been successfully applied in a wide range of flows. The method's popularity is growing due to its relative ease of implementation and minimal intrusiveness as well as an increased demand for C(sub f) measurements. Nonetheless, the accuracy of these methods has not been rigorously addressed to date. Most researchers have simply shown that the skin-friction measurements made using these techniques compare favorably with other measurements and theory, most of which are only accurate to within 5-20%. The use of skin-friction data in the design of commercial aircraft, whose drag at cruise is 50% skin-friction drag, and in the validation of computational fluid dynamics programs warrants better uncertainty estimates. Additional information is contained in the original extended abstract.

Naughton, Jonathan W.↗

NASA NTRS1972

A study of the variations in the thermosphere related to solar activity.

Densities derived from the drag of five artificial satellites and covering the time interval from 1958 to 1971 have been used to study the variations in the thermosphere arising from changes in solar activity. Exospheric temperatures derived from the densities by means of atmospheric models have been related to the 10.7-cm solar flux, in which the active-area component had been separated from the slow-varying clear-disk component by means of a relation between the flux and sunspot areas. When the day-to-day (27-day) variation is suppressed, the remaining slow temperature variation appears to be linearly related to the clear-disk flux component. If we also relate linearly the day-to-day temperature variations with the day-to-day variations of the flux, we find that the regression coefficient changes from 1 K at sunspot maximum to 2 K at low solar activity; a nearly constant coefficient is obtained by relating the temperature variations to the ratio of the active-area component to the clear-disk component of the flux.

Jacchia, L. G.↗

NASA NTRS1921

General Theory of the Steady Motion of an Airplane

The writer points out briefly the history of the method proposed for the study of steady motion of an airplane, which is different from other methods now used. M. Paul Painleve has shown how convenient the drag-lift curve was for the study of airplane steady motion. The author later added to the drift-lift curve the curve called the "speed curve" which permits a direct checking of the speed of the airplane under all flying conditions. But the speed curve was plotted in the same quadrant as the drag-lift curve. Later, with the progressive development of aeronautical science, and with the continually increasing knowledge concerning engines and propellers, the author was brought to add the three other quadrants to the original quadrant, and thus was obtained the steady motion chart which is described in detail in this report. This charts permits one to read directly for a given airplane its horizontal speed at any altitude, its rate of climb at any altitude, its apparent inclination to the horizon at any moment, its ceiling, its propeller thrust, revolutions, efficiency, and power absorbed, that is the complete set of quantities involved in the subject, and to follow the variations of all these quantities both for variable altitude and for variable throttle. The chart also permits one to follow the variation of all of the above in flight as a function of the lift coefficient and of the speed. The author also discusses the interaction of the airplane and propeller through the slipstream and the question of the properties of the engine-propeller system and its dependence upon the properties of the engine considered alone and of the propeller considered alone. There is also a discussion of a standard atmosphere.

De Bothezat, George↗

NASA NTRS1995

Experimental testing using a remotely operated flap with a 2D high lift model

The problem of efficient wind tunnel testing for multi-element airfoils was first addressed by the author during a previous ASEE fellowship. A modern three element model with internal actuators to position a flap in two degrees of freedom was designed and later built. Some preliminary testing proved that the approach was viable. The purpose of this summer's work was to fully develop experimental methods including efficient data acquisition. The final goal is to develop dense data sets for both lift and drag measurements as a function of flap position for both take-off and landing configurations. The model has a span of 36 in. and chord of 18 in. and is currently being fitted for a 3 ft. x 4 ft. low speed wind tunnel. The flap was reworked to allow all pressure taps to function after initial tests showed two blocked ports. The serial method of obtaining pressures from the surface taps was found to be exceedingly slow so a new method using 12 pressure transducers and a 12 port parallel scanning valve were developed. A new automated data acquisition and control algorithm was developed using LabView software and a PC platform. Flow two-dimensionality is currently under investigation with boundary layer control by blowing; this was previously omitted for initial testing. By the end of the summer a detailed data set (uncorrected) consisting of lift coefficient versus flap position for the landing configuration should be available.

Landman, Drew↗

NASA NTRS1960

Measurements of Skin Friction of the Compressible Turbulent Boundary Layer on a Cone with Foreign Gas Injection

Measurements of average skin friction of the turbulent boundary layer have been made on a 15deg total included angle cone with foreign gas injection. Measurements of total skin-friction drag were obtained at free-stream Mach numbers of 0.3, 0.7, 3.5, and 4.7 and within a Reynolds number range from 0.9 x 10(exp 6) to 5.9 x 10(exp 6) with injection of helium, air, and Freon-12 (CCl2F2) through the porous wall. Substantial reductions in skin friction are realized with gas injection within the range of Mach numbers of this test. The relative reduction in skin friction is in accordance with theory-that is, the light gases are most effective when compared on a mass flow basis. There is a marked effect of Mach number on the reduction of average skin friction; this effect is not shown by the available theories. Limited transition location measurements indicate that the boundary layer does not fully trip with gas injection but that the transition point approaches a forward limit with increasing injection. The variation of the skin-friction coefficient, for the lower injection rates with natural transition, is dependent on the flow Reynolds number and type of injected gas; and at the high injection rates the skin friction is in fair agreement with the turbulent boundary layer results.

Pappas, Constantine C.↗

NASA NTRS2004

Atmospheric Models for Aerocapture Systems Studies

Aerocapture uses atmospheric drag to decelerate into captured orbit from interplanetary transfer orbit. This includes capture into Earth orbit from, for example, Lunar-return or Mars-return orbit. Eight Solar System destinations have sufficient atmosphere for aerocapture to be applicable - three of the rocky planets (Venus, Earth, and Mars), four gas giants (Jupiter, Saturn, Uranus, and Neptune), and Saturn's moon Titan. These destinations fall into two groups: (1) The rocky planets, which have warm surface temperatures (approx. 200 to 750 K) and rapid decrease of density with altitude, and (2) the gas giants and Titan, which have cold temperatures (approx. 70 to 170 K) at the surface or 1-bar pressure level, and slow rate of decrease of density with altitude. The height variation of average density with altitude above 1-bar pressure level for the gas giant planets is shown. The periapsis density required for aerocapture of spacecraft having typical values of ballistic coefficient (a measure of mass per unit cross-sectional area) is also shown. The aerocapture altitudes at the gas giants would typically range from approx. 150 to 300 km. Density profiles are compared for the rocky planets with those for Titan and Neptune. Aerocapture at the rocky planets would occur at heights of approx. 50 to 100 km. For comparison, typical density and altitudes for aerobraking operations (circularizing a highly elliptical capture orbit, using multiple atmospheric passes) are also indicated.

Justus, C. G.↗

NASA NTRS2013

Extraction and Separation Modeling of Orion Test Vehicles with ADAMS Simulation

The Capsule Parachute Assembly System (CPAS) project has increased efforts to demonstrate the performance of fully integrated parachute systems at both higher dynamic pressures and in the presence of wake fields using a Parachute Compartment Drop Test Vehicle (PCDTV) and a Parachute Test Vehicle (PTV), respectively. Modeling the extraction and separation events has proven challenging and an understanding of the physics is required to reduce the risk of separation malfunctions. The need for extraction and separation modeling is critical to a successful CPAS test campaign. Current PTV-alone simulations, such as Decelerator System Simulation (DSS), require accurate initial conditions (ICs) drawn from a separation model. Automatic Dynamic Analysis of Mechanical Systems (ADAMS), a Commercial off the Shelf (COTS) tool, was employed to provide insight into the multi-body six degree of freedom (DOF) interaction between parachute test hardware and external and internal forces. Components of the model include a composite extraction parachute, primary vehicle (PTV or PCDTV), platform cradle, a release mechanism, aircraft ramp, and a programmer parachute with attach points. Independent aerodynamic forces were applied to the mated test vehicle/platform cradle and the separated test vehicle and platform cradle. The aero coefficients were determined from real time lookup tables which were functions of both angle of attack ( ) and sideslip ( ). The atmospheric properties were also determined from a real time lookup table characteristic of the Yuma Proving Grounds (YPG) atmosphere relative to the planned test month. Representative geometries were constructed in ADAMS with measured mass properties generated for each independent vehicle. Derived smart separation parameters were included in ADAMS as sensors with defined pitch and pitch rate criteria used to refine inputs to analogous avionics systems for optimal separation conditions. Key design variables were dispersed in a Monte Carlo analysis to provide the maximum expected range of the state variables at programmer deployment to be used as ICs in DSS. Extensive comparisons were made with Decelerator System Simulation Application (DSSA) to validate the mated portion of the ADAMS extraction trajectory. Results of the comparisons improved the fidelity of ADAMS with a ramp pitch profile update from DSSA. Post-test reconstructions resulted in improvements to extraction parachute drag area knock-down factors, extraction line modeling, and the inclusion of ball-to-socket attachments used as a release mechanism on the PTV. Modeling of two Extraction parachutes was based on United States Air Force (USAF) tow test data and integrated into ADAMS for nominal and Monte Carlo trajectory assessments. Video overlay of ADAMS animations and actual C-12 chase plane test videos supported analysis and observation efforts of extraction and separation events. The COTS ADAMS simulation has been integrated with NASA based simulations to provide complete end to end trajectories with a focus on the extraction, separation, and programmer deployment sequence. The flexibility of modifying ADAMS inputs has proven useful for sensitivity studies and extraction/separation modeling efforts. 1

Fraire, Usbaldo, Jr.↗

DOE OSTI2022

Local correlation-based transition models for high-Reynolds-number wind-turbine airfoils

Abstract. Modern wind-turbine airfoil design requires robust performance predictions for varying thicknesses, shapes, and appropriate Reynolds numbers. The airfoils of current large offshore wind turbines operate with chord-based Reynolds numbers in the range of 3–15 million. Turbulence transition in the airfoil boundary layer is known to play an important role in the aerodynamics of these airfoils near the design operating point. While the lack of prediction of lift stall through Reynolds-averaged Navier–Stokes (RANS) computational fluid dynamics (CFD) is well known, airfoil design using CFD requires the accurate prediction of the glide ratio (L/D) in the linear portion of the lift polar. The prediction of the drag bucket and the glide ratio is greatly affected by the choice of the transition model in RANS CFD of airfoils. We present the performance of two existing local correlation-based transition models – one-equation model (γ− SA) and two-equation model (γ-Reθt‾- SA) coupled with the Spalart–Allmaras (SA) RANS turbulence model – for offshore wind-turbine airfoils operating at a high Reynolds number. We compare the predictions of the two transition models with available experimental and CFD data in the literature in the Reynolds number range of 3–15 million including the AVATAR project measurements of the DU00-W-212 airfoil. Both transition models predict a larger L/D compared to fully turbulent results at all Reynolds numbers. The two models exhibit similar behavior at Reynolds numbers around 3 million. However, at higher Reynolds numbers, the one-equation model fails to predict the natural transition behavior due to early transition onset. The two-equation transition model predicts the aerodynamic coefficients for airfoils of various thickness at higher Reynolds numbers up to 15 million more accurately compared to the one-equation model. As a result, the two-equation model predictions are more comparable to the predictions from eN transition model. However, a limitation of this model is observed at very high Reynolds numbers of around 12–15 million where the predictions are very sensitive to the inflow turbulent intensity. The combination of the two-equation transition model coupled with the Spalart–Allmaras (SA) RANS turbulence model is a good method for performance prediction of modern wind-turbine airfoils using CFD.

17 WIND ENERGY↗

NASA NTRS1991

Minimum fuel coplanar aeroassisted orbital transfer using collocation and nonlinear programming

The fuel optimal control problem arising in coplanar orbital transfer employing aeroassisted technology is addressed. The mission involves the transfer from high energy orbit (HEO) to low energy orbit (LEO) without plane change. The basic approach here is to employ a combination of propulsive maneuvers in space and aerodynamic maneuvers in the atmosphere. The basic sequence of events for the coplanar aeroassisted HEO to LEO orbit transfer consists of three phases. In the first phase, the transfer begins with a deorbit impulse at HEO which injects the vehicle into a elliptic transfer orbit with perigee inside the atmosphere. In the second phase, the vehicle is optimally controlled by lift and drag modulation to satisfy heating constraints and to exit the atmosphere with the desired flight path angle and velocity so that the apogee of the exit orbit is the altitude of the desired LEO. Finally, the second impulse is required to circularize the orbit at LEO. The performance index is maximum final mass. Simulation results show that the coplanar aerocapture is quite different from the case where orbital plane changes are made inside the atmosphere. In the latter case, the vehicle has to penetrate deeper into the atmosphere to perform the desired orbital plane change. For the coplanar case, the vehicle needs only to penetrate the atmosphere deep enough to reduce the exit velocity so the vehicle can be captured at the desired LEO. The peak heating rates are lower and the entry corridor is wider. From the thermal protection point of view, the coplanar transfer may be desirable. Parametric studies also show the maximum peak heating rates and the entry corridor width are functions of maximum lift coefficient. The problem is solved using a direct optimization technique which uses piecewise polynomial representation for the states and controls and collocation to represent the differential equations. This converts the optimal control problem into a nonlinear programming problem which is solved numerically by using a modified version of NPSOL. Solutions were obtained for the described problem for cases with and without heating constraints. The method appears to be more robust than other optimization methods. In addition, the method can handle complex dynamical constraints.

Shi, Yun Yuan↗

NASA NTRSDate not supplied

Transonic Correction Method for Flight Dynamic Stability Analysis of Mach 0.745 Transonic Truss-Braced Wing

This paper presents a transonic correction method for obtaining dynamic stability derivatives for flight dynamic stability analysis. The method provides a transonic correction to the Theodorsen's theory of unsteady aerodynamics using FUN3D CFD solver of unsteady Reynolds-averaged Navier-Stokes equations (RANS) for a series of wing sections of the Mach 0.745 Transonic Truss-Braced Wing in pitch and plunge oscillations. Unsteady lift and pitching moment coefficients are obtained and used to develop the correction terms in the Theodorsen's theory to account for transonic aerodynamics. The unsteady lift and pitching moment derivatives with respect to the unsteady angle of attack are obtained as frequency response functions of the reduced frequency. These frequency response functions are used to compute the dynamic stability derivatives of lift and pitching moment due to the angle of attack and pitch rate and the dynamic stability derivatives for the rolling moment and yawing moment with respect to the roll rate and yaw rate. A transonic correction is applied to steady-state stability derivatives computed by VSPAERO solver using transonic small disturbance code TSFOIL coupled to an integral boundary method. A dynamic stability analysis is conducted for longitudinal and lateral-directional motions. Without transonic corrections and dynamic stability derivatives, the analysis indicates an unstable phugoid mode. The transonic correction applied to the steady-state stability derivatives computed by VSPAERO shows a stable phugoid mode. This is due to the increase of the drag stability derivatives as a result of the additional wave drag contribution in transonic flow. The effect of the transonic dynamic stability derivatives is observed to be a significant contributor to the increase in the damping values of all the flight dynamic modes of the Mach 0.745 Transonic-Truss Braced Wing.

Transonic↗

NASA NTRS2021

Experimental Flight Validation of the Prandtl 1933 Bell Spanload

This report describes the validation of the 1933 Prandtl bell spanload. This spanload is the minimum induced drag of a wing for a given structural weight with properties that eliminate adverse yaw. Aircraft using the Prandtl bell spanload were flown and investigated. The results of this research show that many previously held assumptions should be rethought, and the creation of aircraft using the Prandtl bell spanload will require considerable new techniques. Part of this work centered on the use of inverse methods. The usual first-step approach to a computational fluids problem is to create a geometry of the aircraft. Once this geometry exists, the computational fluids solution has been solved; however, the problem of creating the geometry still exists. A very small segment of the computational fluids world has concentrated on inverse solutions. This design approach begins with an end result - the computational fluids solution; from this end result, the geometry is sought. A more generic inverse tool was desired that would allow for the design of wings - specifically Prandtl bell spanload wings. Such a tool has been developed and allows for variable taper, aspect ratio, sweep, airfoils, and design-lift coefficients; output from the tool results in twist distribution of wings.

Albion H. Bowers↗

NASA NTRS1993

Quasi-decadal variability of the stratosphere: Influence of long-term solar ultraviolet variations

A multiple regression statistical model is applied to investigate the existence of upper-stratospheric ozone, temperature, and zonal wind responses to long-term (solar cycle) changes in solar ultraviolet radiation using 11.5 years of reprocessed Nimbus-7 Solar Backscattered Ultraviolet (SBUV) data and 12.4 years of National Meteorological Center (NMC) data. A positive solar cycle variation of independently measured ozone and temperature occurs with maximum amplitude near the low-latitude stratopause. The seasonal solar regression coefficients near 1 mb for both ozone and temperature occur at low latitudes supporting a role for photochemical and radiative forcing in their origin. Zonal wind perturbations that correlate with long-term solar ultraviolet variations are a strong function of season and pressure level. Above approximately 2 mbar, the largest solar-correlated zonal wind enhancements occur at middle winter latitudes near the time of winter solstice in both hemispheres. The Northern Hemisphere December enhancement at 1 mb was especially large, 23 +/- 9 m/s from solar minimum to maximum during the last solar cycle. The derived ozone, temperature, and zonal wind increases with increasing solar ultraviolet flux near the stratopause are larger than predicted by models that consider primarily photochemical and radiative processes. The higher ozone and temperature response amplitudes at low latitudes may be due to modified ozone transport and adiabatic temperature changes induced by the dynamical response. If the midlatitude winter solstice wind enhancements are solar induced, their high amplitudes require a positive feedback due to wave-mean flow interaction such that the planetary wave drag on the flow is reduced under solar maximum conditions.

Hood, L. L.↗

DOE OSTI2025

OC7 Phase I Definition Document

The Offshore Code Comparison Collaboration 7 (OC7) project is organized under the International Energy Agency Wind Technology Collaboration Programme Task 56 with an objective to evaluate and enhance the predictive accuracy of engineering-level modeling tools used in the design of offshore wind energy systems. Phase I of OC7 is focused on improving the models and modeling practices of hydrodynamic viscous loads on floating offshore wind turbine platforms. In alignment with this goal, Work Package 1.1 of OC7 Phase I is formulated to investigate the modeling of hydrodynamic viscous loads on several different geometric components commonly encountered with floating offshore wind platform designs, including cylindrical columns, heave plates, and rectangular pontoons. Work Package 1.1 also explores the dependence of hydrodynamic coefficients on the sea state to drive toward practical guidance on how these coefficients can be selected or adjusted for different conditions. This report outlines the motivation and objectives behind each subphase of OC7 Phase I, along with the necessary technical specifications and load case definitions to guide the project participants. It also serves as an important part of the project documentation for future modelers who would like to reproduce this work or make use of the data and information generated from the OC7 project.

17 WIND ENERGY↗

NASA NTRS1981

Full-scale study of the cooling system aerodynamics of an operating piston engine installed in a light aircraft wing panel

Measurements of the drag and of the nacelle internal pressures on a wing and nacelle that housed a horizontally opposed piston engine were made in the 40- by 80-Foot Wind Tunnel at Ames Research Center. These tests are follow-ons to earlier tests made with the same wing and nacelle but in which the engine was replaced with an electric motor and an adjustable orifice plate. In the initial tests the orifice plate was used to control the rate of cooling-air flow through the nacelle and thereby to simulate a range of gasoline engine types. Good agreement was found between the results of those tests and of the test reported here. Also, the upper and lower plenum pressure and cooling-air flow rate were found to be related by conventional equations used to represent the flow through orifices. Tests were run with three cooling air inlet sizes over a free-stream velocity range from 50 to 150 knots, an angle of attack range from 0 deg to 10 deg, and a cowl-flap deflection range from 0 deg to 30 deg. The data were analyzed by computing a flow coefficient similar to that used in the analysis of orifices. It was found that all of the flow coefficient values fell within a band that varied linearly with inlet area. The linear mean line through this band provides an estimate of the relationship between cooling-air flow rate and upper plenum pressure over a wide range of test conditions.

Corsiglia, V. R.↗

NASA NTRS2016

Generalized Fluid System Simulation Program, Version 6.0

The Generalized Fluid System Simulation Program (GFSSP) is a general purpose computer program for analyzing steady state and time-dependent flow rates, pressures, temperatures, and concentrations in a complex flow network. The program is capable of modeling real fluids with phase changes, compressibility, mixture thermodynamics, conjugate heat transfer between solid and fluid, fluid transients, pumps, compressors, and external body forces such as gravity and centrifugal. The thermofluid system to be analyzed is discretized into nodes, branches, and conductors. The scalar properties such as pressure, temperature, and concentrations are calculated at nodes. Mass flow rates and heat transfer rates are computed in branches and conductors. The graphical user interface allows users to build their models using the 'point, drag, and click' method; the users can also run their models and post-process the results in the same environment. Two thermodynamic property programs (GASP/WASP and GASPAK) provide required thermodynamic and thermophysical properties for 36 fluids: helium, methane, neon, nitrogen, carbon monoxide, oxygen, argon, carbon dioxide, fluorine, hydrogen, parahydrogen, water, kerosene (RP-1), isobutene, butane, deuterium, ethane, ethylene, hydrogen sulfide, krypton, propane, xenon, R-11, R-12, R-22, R-32, R-123, R-124, R-125, R-134A, R-152A, nitrogen trifluoride, ammonia, hydrogen peroxide, and air. The program also provides the options of using any incompressible fluid with constant density and viscosity or ideal gas. The users can also supply property tables for fluids that are not in the library. Twenty-four different resistance/source options are provided for modeling momentum sources or sinks in the branches. These options include pipe flow, flow through a restriction, noncircular duct, pipe flow with entrance and/or exit losses, thin sharp orifice, thick orifice, square edge reduction, square edge expansion, rotating annular duct, rotating radial duct, labyrinth seal, parallel plates, common fittings and valves, pump characteristics, pump power, valve with a given loss coefficient, Joule-Thompson device, control valve, heat exchanger core, parallel tube, and compressible orifice. The program has the provision of including additional resistance options through User Subroutines. GFSSP employs a finite volume formulation of mass, momentum, and energy conservation equations in conjunction with the thermodynamic equations of state for real fluids as well as energy conservation equations for the solid. The system of equations describing the fluid network is solved by a hybrid numerical method that is a combination of the Newton-Raphson and successive substitution methods. The application and verification of the code has been demonstrated through 30 example problems.

Majumdar, A. K.↗

NASA NTRS1990

Natural laminar flow application to transport aircraft

A major goal of NASA during the last 15 years has been the development of laminar flow technology for aircraft drag reduction. Of equal importance is achieving a state of readiness that will allow the successful application of this technology by industry to large, long-range aircraft. Recent progress in achieving extensive laminar flow with limited suction on the Boeing 757 has raised the prospects from practical application of the hybrid laminar flow control (HLFC) concept to subsonic aircraft. Also, better understanding of phenomena affecting laminar flow stability and response to disturbances has encouraged consideration of natural laminar flow (NLF), obtained without suction or active mechanical means, for application to transport aircraft larger than previously thought feasible. These ideas have inspired the current NASA/ASEE project with goals as follows: explore the feasibility of extensive NLF for aircraft at high Reynolds number under realistic flight conditions; determine the potential applications of NLF technology and the conditions under which they may be achieved; and identify existing aircraft that could be adapted to carry out flight experiments to validate NLF technology application. To achieve these objectives, understanding of the physical limits to natural laminar flow and possible ways to extend these limits was sought. The primary factors involved are unit Reynolds number, Mach number, wing sweep, thickness, and lift coefficients as well as surface pressure gradients and curvature. Based on previous and ongoing studies using laminar boundary layer stability theory, the interplay of the above factors and the corresponding transition limits were postulated.

Gratzer, Louis B.↗