Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dislocation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

Precipitation in solution-treated Al-4wt%Cu under cyclic strain

Solution-treated Al-4wt%Cu was strain-cycled at ambient temperature and above and the precipitation behavior investigated by TEM. In the temperature range 100 C to 200 C precipitation of {Theta}'' appears to have been suppressed and precipitation of {Theta}' promoted via cyclic strain. Anomalously rapid growth of precipitates appears to have been facilitated by a vacancy supersaturation generated by dislocation motion, with a diminishing effect observed at higher temperatures due to the faster recovery of non-equilibrium vacancy concentrations. {Theta}' precipitates generated under cyclic strain are considerably smaller and more finely dispersed than those typically produced via quench-aging due to their heterogeneous nucleation on dislocations, and possess a low aspect ratio and rounded edges of the broad faces due to the introduction of ledges into the growing precipitates by dislocation cutting. Frequency effects indicate that dislocation motion, rather than the extremely small precipitate size, is responsible for the observed reduction in aspect ratio. Accelerated formation of grain boundary precipitates appears partially responsible for rapid intergranular fatigue failure following cycling at elevated temperatures, producing fatigue striations and ductile dimples coexistent on the fracture surface.

36 MATERIALS SCIENCE↗

Influence of orientation on the size effect in BCC pillars with different critical temperatures.

The size effect in body-centered cubic metals is comprehensively investigated through micro/nano-compression tests performed on focused ion beam machined tungsten (W), molybdenum (Mo) and niobium (Nb) pillars, with single slip [2 3 5] and multiple slip [0 0 1] orientations. The results demonstrate that the stress-strain response is unaffected by the number of activated slip systems, indicating that dislocation-dislocation interaction is not a dominant mechanism for the observed diameter dependent yield strength and strain hardening. Furthermore, the limited mobility of screw dislocations, which is different for each material at ambient temperature, acts as an additional strengthening mechanism leading to a material dependent size effect. Nominal values and diameter dependence of the flow stress significantly deviate from studies on face-centered cubic metals. This is demonstrated by the correlation of size dependence with the material specific critical temperature. Activation volumes were found to decrease with decreasing pillar diameter further indicating that the influence of the screw dislocations decreases with smaller pillar diameter.

36 MATERIALS SCIENCE↗

An effect of the networks of the subgrain boundaries on spectral responses of thick CdZnTe detectors

CdZnTe (CZT) crystals used for nuclear-radiation detectors often contain high concentrations of subgrain boundaries and networks of poligonized dislocations that can significantly degrade the performance of semiconductor devices. These defects exist in all commercial CZT materials, regardless of their growth techniques and their vendor. We describe our new results from examining such detectors using IR transmission microscopy and white X-ray beam diffraction topography. We emphasize the roles on the devices performances of networks of subgrain boundaries with low dislocation densities, such as poligonized dislocations and mosaic structures. Specifically, we evaluated their effects on the gamma-ray responses of thick, >10 mm, CZT detectors. Our findings set the lower limit on the energy resolution of CZT detectors containing dense networks of subgrain boundaries, and walls of dislocations.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Microstructural creep, fatigue and creep-fatigue modeling of Nickel-based superalloy Inconel 617 at high temperature - 18506

Inconel 617 is a solution strengthened nickel-based alloy which has been considered as one of the leading structural material for the intermediate heat exchangers (IHX) in very high temperature reactor (VHTR). In order to gain understanding of the creep and fatigue deformation mechanisms and their interactions in alloy 617 operating in the VHTR environment, a computational model that operates at the microstructural scale has been developed for creep, fatigue and creep-fatigue modeling of alloy 617. This model is based on an isothermal, large deformation crystal plasticity finite element (CPFE) formulation and idealizes the deformation in the crystal lattice as collective glide and climb of dislocations. A recently developed glide resistance evolution equation by the authors that can capture the intermediate softening observed in both fatigue and creep-fatigue cycles of Inconel 617 at high temperature is adopted for the dislocation glide formulation. Dislocation climb is incorporated to account for the interactions between dislocations and local point defects at high temperature. The CP equations are solved incrementally as the constitutive relationship in the context of FE analysis on fully resolved microstructure reconstructed from experiment data. Model parameters are calibrated and verified using experimental tests. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

A mesh-independent method for planar three-dimensional crack growth in finite domains: A mesh-independent method for crack growth in 3D finite domains

The discrete crack mechanics (DCM) method is a dislocation-based crack modeling technique where cracks are constructed using Volterra dislocation loops. The method allows for the natural introduction of displacement discontinuities, avoiding numerically expensive techniques. Mesh dependence in existing computational modeling of crack growth is eliminated by utilizing a superposition procedure. The elastic field of cracks in finite bodies is separated into two parts: the infinite-medium solution of discrete dislocations and an finite element method solution of a correction problem that satisfies external boundary conditions. In the DCM, a crack is represented by a dislocation array with a fixed outer loop determining the crack tip position encompassing additional concentric loops free to expand or contract. Solving for the equilibrium positions of the inner loops gives the crack shape and stress field. The equation of motion governing the crack tip is developed for quasi-static growth problems. Additionally, convergence and accuracy of the DCM method are verified with two- and three-dimensional problems with well-known solutions. Crack growth is simulated under load and displacement (rotation) control. In the latter case, a semicircular surface crack in a bent prismatic beam is shown to change shape as it propagates inward, stopping as the imposed rotation is accommodated.

42 ENGINEERING↗

In Situ TEM Investigation of ZnO Nanowires during Sodiation and Lithiation Cycling

The development of sodium-ion batteries has drawn lots of attention recently due to the low-cost and eco-friendly sodium source. However, a fundamental understanding of the sodiation behavior for commonly used electrode materials is still limited. Here, combining in situ transmission electron microscopy, aberration-corrected scanning transmission electron microscopy, and ex situ battery cycling tests, the lithiation and sodiation behavior of ZnO nanowires is investigated. The findings show a direct correlation between the mechanical behavior of the lithiated/sodiated ZnO nanowires and their electrochemical cyclability. The mechanical brittleness of LiZn and the formation of nanocracks lead to the poor cyclability of Li-ion batteries with a ZnO anode. However, the sodiated ZnO nanowires show profuse dislocation plasticity. The observed high-density dislocations offer the sodiated ZnO anode more ductility and subsequently better cyclability than its Li-ion counterpart. The results reveal the importance of understanding the correlation between mechanical properties of battery electrodes and their cycling abilities.

Asayesh-Ardakani, Hasti↗

Three-dimensional nonlocal anisotropic elasticity: a generalized continuum theory of Ångström-mechanics

In this paper, based on Eringen’s theory of nonlocal anisotropic elasticity, the three-dimensional nonlocal anisotropic elasticity of generalized Helmholtz type is developed. The derivation of a new three-dimensional nonlocal anisotropic kernel, which is the Green function of the three-dimensional anisotropic Helmholtz equation, enables to capture anisotropic length scale effects by means of a length scale tensor, which is a symmetric tensor of rank two. The derived nonlocal kernel function possesses up to six internal characteristic lengths on the Ångström-scale. The presented theory of nonlocal elasticity possesses the appropriate property to be a generalized continuum theory of Ångström-mechanics, since the range of its validity and applicability is up to the Ångström-scale. The connection between the theory of nonlocal anisotropic elasticity and lattice theory is established. The tensor function of nonlocal elastic moduli as well as the nonlocal kernel function is given in terms of the Hessian matrix in the lattice approach. In the framework of the considered theory, the modeling of dislocations in anisotropic materials taking into consideration anisotropic dislocation core effects is presented. Important dislocation key formulas, namely the anisotropic Peach–Koehler stress formula, the Peach–Koehler force and the anisotropic Blin’s formula, are derived. A major tool used in deriving the expression of anisotropic Blin’s formula is Kirchner’s so-called FF-tensor, which is here generalized toward nonlocal anisotropic elasticity. The main feature and advantage of the derived fields, compared with the corresponding ones in classical anisotropic elasticity, is that they are free of singularities. Numerical applications to straight dislocations in bcc Fe are given, revealing the ability and advantage of the considered theory to describe adequately nonsingular anisotropic stress and self-energy fields capturing the effects of anisotropy on the Ångström-scale.

42 ENGINEERING↗

Temperature and radiation effects on brittle versus ductile fracture behavior in miscible phase boundaries: insight from atomistic simulations

Temperature- and irradiation-assisted failure mechanisms in miscible phase boundaries are clarified via atomistic calculations. We first establish the temperature-dependent brittle-to-ductile transition in U–Zr miscible phase boundaries. Our results confirm that these boundaries are mostly brittle at low temperatures and ductile at elevated temperatures. We then investigate the changes induced by irradiation on the fracture mechanisms in such phase boundaries. The irradiation-induced defect accumulation follows a multi-stage process that starts with the accumulation of isolated small dislocation loops before transitioning to the saturation and growth of larger dislocation loops and end up with a reorganization into forest dislocations. The accumulation of loops is the primary feature to participate in the delineation between brittle and ductile interfacial fracture in irradiated phase boundaries. At low damage levels, radiation defect interactions with the crack tip are limited and U–Zr miscible boundaries fail through the emission of dislocations ahead of the crack tip followed by brittle cleavage in agreement with the classical Griffith’s criterion for crack stability. At higher damage levels, the failure mode transitions from brittle crack growth to ductile void growth. In this case, the microcrack tip is blunted by the high density of pre-existing, radiation-induced defects in the vicinity of the crack. This interaction leads to the development and growth of a cavity at the interface as opposed to interfacial cleavage.

36 MATERIALS SCIENCE↗

Suppression of Void Nucleation in High-Purity Aluminum via Dynamic Recrystallization

The process of ductile fracture in metals often begins with void nucleation at second-phase particles and inclusions. Previous studies of rupture in high-purity face-centered-cubic metals, primarily aluminum (Al), concluded that second-phase particles are necessary for cavitation. A recent study of tantalum (Ta), a body-centered-cubic metal, demonstrated that voids nucleate readily at deformation-induced dislocation boundaries. These same features form in Al during plastic deformation. This study investigates why void nucleation was not previously observed at dislocation boundaries in Al. Here, we demonstrate that void nucleation is impeded in Al by room-temperature dynamic recrystallization (DRX), which erases these boundaries before voids can nucleate at them. If dislocation cells reform after DRX and before specimen separation by necking, voids nucleation is observed. These results indicate that dislocation substructures likely plays an important role in ductile rupture.

36 MATERIALS SCIENCE↗

Transmission Electron Microscope In Situ Straining Technique to Directly Observe Defects and Interfaces During Deformation in Magnesium

In-situ straining was used to study deformation behavior of hexagonal close-packed (hcp) metals.Twinning and dislocation motion, both essential to plasticity in hcp materials, were observed.Typically, these processes are characterized post-mortem by examining remnant microstructural features after straining has occurred. By imposing deformation during imaging, direct observation of active deformation mechanisms is possible. This work focuses on straining of structural metals in a transmission electron microscope (TEM), and a recently developed technique that utilizes familiar procedures and equipment to increase ease of experiments. In-situ straining in a TEM presents several advantages over conventional post-mortem characterization, most notably time-resolution of deformation and streamlined identification of active deformation mechanisms. Drawbacks to the technique and applicability to other studies are also addressed. In-situ straining is used to study twin boundary motion in hcp magnesium. A {101¯2} twin was observed during tensile and compressive loading. Twin-dislocation interactions are directly observed. Notably, dislocations are observed to remain mobile, even after multiple interactions with twin boundaries, a result which suggests that Basinki’s dislocation transformation mechanism by twinning is not present in hcp metals. The coupling of in-situ straining with traditional post-mortem characterization yields more detailed information about material behavior during deformation than either technique alone.

magnesium↗

Deformation mechanisms in a precipitation-strengthened ferritic super alloy revealed by in situ neutron dffraction studies at elevated temperatures

The ferritic superalloy Fe–10Ni–6.5Al–10Cr–3.4Mo strengthened by ordered (Ni,Fe)AlB2-type precipitates is a candidate material for ultra-supercritical steam turbine applications above 923 K. Despite earlier success in improving its room-temperature ductility, the creep resistance of this material at high temperatures needs to be further improved, which requires a fundamental understanding of the high-temperature deformation mechanisms at the scales of individual phases and grains. In situ neutron diffraction has been utilized to investigate the lattice strain evolution and the microscopic load-sharing mechanisms during tensile deformation of this ferritic superalloy at elevated temperatures. Finite-element simulations based on the crystal plasticity theory are employed and compared with the experimental results, both qualitatively and quantitatively. Based on these interphase and intergranular load-partitioning studies, it is found that the deformation mechanisms change from dislocation slip to those related to dislocation climb, diffusional flow and possibly grain boundary sliding, below and above 873 K, respectively. Insights into microstructural design for enhancing creep resistance are also discussed.

nuclear (including radiation effects), defects, me↗

In situ high-energy X-ray diffraction study of tensile deformation of neutron-irradiated polycrystalline Fe-9%Cr alloy

The effect of neutron irradiation on tensile deformation of a Fe-9wt.%Cr alloy was investigated using in situ high-energy synchrotron X-ray diffraction during room-temperature uniaxial tensile tests. New insights into the deformation mechanisms were obtained through the measurements of lattice strain evolution and the analysis of diffraction peak broadening using the modified Williamson-Hall method. Two neutron-irradiated specimens, one irradiated at 300 °C to 0.01 dpa and the other at 450 °C to 0.01dpa, were tested along with an unirradiated specimen. The macroscopic stress–strain curves of the irradiated specimens showed increased strength, reduced ductility and work-hardening exponent compared to the unirradiated specimen. The evolutions of the lattice strain, the dislocation density and the coherent scattering domain size in the deformation process revealed different roles of the submicroscopic defects in the 300°C/0.01 dpa specimen and the TEM-visible nanometer-sized dislocation loops in the 450°C/0.01 dpa specimen: submicroscopic defects extended the linear work hardening stage (stage II) to a higher strain, while irradiation-induced dislocation loops were more effective in dislocation pinning. Lastly, while the work hardening rate of stage II was unaffected by irradiation, significant dynamic recovery in stage III in the irradiated specimens led to the early onset of necking without stage IV as observed in the unirradiated specimen.

36 MATERIALS SCIENCE↗

An investigation of the microstructure and ductility of annealed cold-rolled tungsten

Tungsten is notoriously brittle metal at room temperature. Furthermore, contrary to most metals, plastic deformation increases ductility and recrystallization decreases ductility of tungsten. The fundamentals that govern this behavior have challenged academia and industry for decades. This paper focuses on understanding the controlling factors of ductility through a systematic investigation of the changes in microstructure and mechanical properties of cold-rolled tungsten that occur during annealing. Cold-rolled tungsten samples were annealed at temperatures up to 1400 °C, and mechanical testing and microstructural analysis was performed before and after annealing. Furthermore, a dislocation mobility model based on the Orowan equation was applied. The mechanisms of deformation are discussed within the context of deformed and annealed microstructures. The high fraction of low angle grain boundaries and high density of edge dislocations were found to be the most important factors for ductility. Although there were gradual changes in microstructure and mechanical properties, the ductility of cold-rolled tungsten was maintained up to 1300 °C. The material recrystallized when annealed above this temperature, had no ductility, and suffered brittle fracture. Microstructural characterizations of the as-rolled material revealed a typical BCC texture, with grains elongated in rolling direction and a large amount of edge dislocations and low angle grain boundaries. The level of texturing and the fraction of low angle grain boundaries diminished after recrystallization. It was found that, compared to the recrystallized material, as-rolled tungsten can accommodate over 7 orders of magnitude higher deformation velocity due to the high density of edge dislocations.

36 MATERIALS SCIENCE↗

Nano-scale microstructure damage by neutron irradiations in a novel Boron-11 enriched TiB 2 ultra-high temperature ceramic

Ultra-high temperature transition-metal ceramics are potential candidates for fusion reactor structural and plasma-facing components. We reveal the irradiation damage microstructural phenomena in Boron-11 enriched titanium diboride (TiB 2 ) using mixed-spectrum neutron irradiations, combined with state-of-art characterization using transmission electron microscopy (TEM) and high resolution TEM. Irradiations were performed using High Flux Isotope Reactor at ~220 and 620 °C up to 2.4 x 10 25 n.m -2 (E > 0.1 MeV). The calculated dose including contribution from residual Boron-10 ( 10 B) transmutation recoils, was ~4.2 displacements per atom. TiB 2 is susceptible to irradiation damage in terms of dislocation loop formation, cavities and anisotropic swelling induced micro-cracking. At both 220 and 620 °C, TEM revealed dislocation loops on basal and prism planes, with nearly two orders of magnitude higher number density of prism-plane loops. HRTEM, electron diffraction and relrod imaging revealed additional defects on {10$ \overline{1}\ $0} planes, identified as faulted prism-plane dislocation loops. High defect cluster density on prism planes will induce a-lattice parameter swelling of TiB 2 , as reported in literature. This anisotropic lattice parameter swelling induced grain boundary micro-cracking, the extent of which decreased with increasing irradiation temperature. The dominance of irradiation defect clusters on prism planes is different than typical hexagonal ceramics where dislocation loops predominantly form on basal planes, causing c-lattice parameter swelling. Helium generation and temperature rise from the transmutation of residual 10 B resulted in matrix and grain boundary cavities for the irradiation at 620 °C. In conclusion, the study additionally signifies isotopic enrichment as a viable approach to produce transition-metal diborides for potential nuclear structural applications.

36 MATERIALS SCIENCE↗

Relating microstructure to defect behavior in AA6061 using a combined computational and multiscale electron microscopy approach

In this paper, a multiscale electron microscopy-based approach is applied to understanding how different aspects of the microstructure in a notched AA6061-T6, including grain boundaries, triple junctions, and intermetallic particles, promote localized dislocation accumulation as a function of applied tensile strain and depth from the sample surface. Experimental measurements and crystal plasticity simulations of dislocation distributions as a function of distance from specified microstructural features both showed preferential dislocation accumulation near intermetallic particles relative to grain boundaries and triple junctions. High resolution electron backscatter diffraction and site-specific transmission electron microscopy characterization showed that high levels of dislocation accumulation near intermetallic particles led to the development of an ultrafine sub-grain microstructure, indicative of a much higher level of local plasticity than predicted from the coarser measurements and simulations. In addition, high resolution measurements in front of a crack tip suggested a compounding influence of intermetallic particles and grain boundaries in dictating crack propagation pathways.

36 MATERIALS SCIENCE↗

Neutron irradiation-induced microstructure damage in ultra-high temperature ceramic TiC

Titanium carbide (TiC) is an ultra-high temperature ceramic with potential as a structural material candidate for advanced reactor concepts. However, the irradiation tolerance of TiC is not well understood. Here, we reveal the key irradiation damage microstructure degradation processes in TiC using mixed spectrum neutron irradiations at dose of ~2 displacements per atom (dpa) at temperatures of ~220, 620, and 1115 °C, combined with state-of-art microstructure characterization using transmission electron microscopy (TEM) and high-resolution TEM (HRTEM). The helium injection (~65 atomic parts per million) produced by neutron transmutation also occurred in the sample. TiC was observed to form irradiation-induced interstitial-type dislocation loops and He-stabilized cavities. At 220 and 620 °C, the analysis of the electron diffraction patterns, rel-rod imaging and HRTEM revealed that the dislocation loops were faulted Frank loops with Burgers vector b Frank = 1/3<111> lying on {111} planes. A detailed Burgers vector identification performed by the g.b technique revealed that the dislocation loops forming at 1115 °C were unfaulted, edge-type, with Burgers vectors b = a<100> and a/2<110> with corresponding {100} and {110} habit planes. Using continuum mechanics, we estimated the critical radius at which a faulted dislocation loop transitions to a perfect loop to be 9 nm. Further, no amorphization occurred in TiC under-investigated irradiation conditions while macroscopic swelling under point defect swelling regime was observed. He-stabilized cavities were detected at 1115 °C, but not at lower temperature irradiation. These observations indicate the onset of long-range vacancy migration in TiC occurs between 620 and 1115 °C.

36 MATERIALS SCIENCE↗

Progression of creep deformation from grain boundaries to grain interior in Al-Cu-Mn-Zr alloys

Creep mechanisms are studied in θ'-Al 2 Cu-strengthened Al-Cu-Mn-Zr alloys at 300 and 350°C for (i) ACMZ, a base alloy without further alloying elements and (ii) RR350, a commercial alloy with additions of Ni and Co forming distinct grain-boundary precipitates. At high stresses, creep is dominated by dislocations bypassing θ' precipitates within grains via the Orowan mechanism, as evidenced by (i) very high stress exponent (n~20-25) and (ii) α-Al and θ' lattice strains (measured via in-situ neutron diffraction) evolving during creep in a manner consistent with load transfer from the plastically-deforming α-Al matrix to elastically-deforming θ' precipitates. At intermediate stresses, both alloys exhibit a n~3 regime, where α-Al and θ' lattice strains scale near-linearly with applied stress while remaining largely unaffected by strain accumulation, indicating that Orowan looping or dislocation pile-up around θ' is now inactive within the grains. Rather, dislocation motion occurs solely in θ'-precipitate-free zones (θ'-PFZ) where high dislocation densities are observed via TEM after creep deformation. Plastic flow at θ'-PFZ and/or localized pipe diffusion are expected to enable grain-boundary sliding (GBS), which is proposed as the rate-limiting mechanism in the n~3 regime. Ni/Co-rich precipitates at RR350 grain-boundaries, with negligible θ'-PFZ around them, share load (as determined via neutron diffraction) with the α-Al matrix more effectively than θ-Al 2 Cu precipitates at ACMZ grain-boundaries, with wide surrounding θ'-PFZ. So, high creep resistance in the n~3 GBS regime of RR350 is enabled by coarsening-resistant grain-boundary precipitates, forming without concomitant development of weak θ'-PFZ, which effectively share load with the grains.

36 MATERIALS SCIENCE↗