Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Conditional Distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Comparative plasma tails of Venus and comets

A review of current models of solar wind flow in the plasma tails of weakly magnetized bodies is presented. Measurements conducted by the Mariner 5 spacecraft, the Veneras 9 and 10, and the PVO orbiters, in the Venus tail, and with the ICE spacecraft in the tail of Comet Giacobini-Zinner, reveal common plasma properties which suggest that similar physical processes are operative. Most notable is the observation of decreased flow velocities and enhanced plasma temperatures in the vicinity of their plasma tails. In Venus, the measured velocity and temperature fields are consistent with the effects of frictional forces between the mass-loaded ionosheath flow and the ionosphere along the (magnetic) polar regions of the ionopause. It is argued that similar conditions exist at a cometary ionopause and that the distribution of magnetic fluxes in a cometary tail is controlled by the entry of plasma fluxes from the (magnetic) polar regions of the comet's ionospheric obstacle. This question is further addressed in connection with the two-step shape of the magnetic profile measured across the tail of the comet. It is suggested that the low intensity outer increases of the magnetic lobes are associated with the draping of the interplanetary magnetic field lines around the comet's ionospheric obstacle, and that the higher intensity increases seen in the inner regions of the magnetic lobes are due to an additional compression of magnetic fluxes produced by the entry of plasma particles into the tail.

Perezdetejada, H.↗
NASA NTRS1988

Measured and calculated acoustic attenuation rates of tuned resonator arrays for two surface impedance distribution models with flow

An experiment was performed to validate two analytical models for predicting low frequency attenuation of duct liner configurations built from an array of seven resonators that could be individually tuned via adjustable cavity depths. These analytical models had previously been developed for high frequency aero-engine inlet duct liner design. In the low frequency application, the liner surface impedance distribution is unavoidably spatially varying by virtue of available fabrication techniques. The characteristic length of this spatial variation may be a significant fraction of the acoustic wavelength. Comparison of measured and predicted attenuation rates and transmission losses for both modal decomposition and finite element propagation models were in good to excellent agreement for a test frequency range that included the first and second cavity resonance frequencies. This was true for either of two surface impedance distribution modeling procedures used to simplify the impedance boundary conditions. In the presence of mean flow, measurements revealed a fine scale structure of acoustic hot spots in the attenuation and phase profiles. These details were accurately predicted by the finite element model. Since no impedance changes due to mean flow were assumed, it is concluded that this fine scale structure was due to convective effects of the mean flow interacting with the surface impedance nonuniformities.

Parrott, Tony L.↗
NASA NTRS1987

The topology of large-scale structure. I - Topology and the random phase hypothesis

Many models for the formation of galaxies and large-scale structure assume a spectrum of random phase (Gaussian), small-amplitude density fluctuations as initial conditions. In such scenarios, the topology of the galaxy distribution on large scales relates directly to the topology of the initial density fluctuations. Here a quantitative measure of topology - the genus of contours in a smoothed density distribution - is described and applied to numerical simulations of galaxy clustering, to a variety of three-dimensional toy models, and to a volume-limited sample of the CfA redshift survey. For random phase distributions the genus of density contours exhibits a universal dependence on threshold density. The clustering simulations show that a smoothing length of 2-3 times the mass correlation length is sufficient to recover the topology of the initial fluctuations from the evolved galaxy distribution. Cold dark matter and white noise models retain a random phase topology at shorter smoothing lengths, but massive neutrino models develop a cellular topology.

Weinberg, David H.↗
NASA NTRS1986

Analytical and experimental studies of the surface flaw

This paper uses the Newman-Raju model, the Paris crack growth rate law, and a fixed R ratio to demonstrate the analytical considerations associated with predicting stress intensity distributions and fatigue crack growth of surface flaws under conditions of small-scale yielding. Problems which lie outside the realm of the model used in the analytical description are presented. It is concluded that, while the model employed provides remarkable predictive capability in a variety of surface flaw problems, many exceptional cases remain to be modeled.

Smith, C. W.↗
NASA NTRS1989

Microparticle impacts in space: Results from Solar Max and shuttle witness plate inspections

The Solar Maximum Satellite developed electronic problems after operating successfully in space for several years. Astronauts on Space Shuttle mission STS-41C retrieved the satellite into the orbiter cargo bay, replaced defective components, and re-deployed the repaired satellite into orbit. The defective components were returned to Earth for study. The space-exposed surfaces were examined. The approach and objectives were to: document morphology of impact; find and analyze projectile residue; classify impact by origin; determine flux distribution; and determine implications for space exposure. The purpose of the shuttle witness plate experiment was to detect impacts from PAM D2 solid rocket motor; determine flux and size distribution of particles; and determine abrasion effects on various conditions. Results are given for aluminum surfaces, copper surfaces, stainless steel surfaces, Inconel surfaces, and quartz glass surfaces.

Mckay, David S.↗
NASA NTRS1989

Predeployment validation of fault-tolerant systems through software-implemented fault insertion

Fault injection-based automated testing (FIAT) environment, which can be used to experimentally characterize and evaluate distributed realtime systems under fault-free and faulted conditions is described. A survey is presented of validation methodologies. The need for fault insertion based on validation methodologies is demonstrated. The origins and models of faults, and motivation for the FIAT concept are reviewed. FIAT employs a validation methodology which builds confidence in the system through first providing a baseline of fault-free performance data and then characterizing the behavior of the system with faults present. Fault insertion is accomplished through software and allows faults or the manifestation of faults to be inserted by either seeding faults into memory or triggering error detection mechanisms. FIAT is capable of emulating a variety of fault-tolerant strategies and architectures, can monitor system activity, and can automatically orchestrate experiments involving insertion of faults. There is a common system interface which allows ease of use to decrease experiment development and run time. Fault models chosen for experiments on FIAT have generated system responses which parallel those observed in real systems under faulty conditions. These capabilities are shown by two example experiments each using a different fault-tolerance strategy.

Czeck, Edward W.↗
NASA NTRS1990

A scheme for parameterizing cirrus cloud ice water content in general circulation models

Clouds strongly influence th earth's energy budget. They control th amount of solar radiative energy absorbed by the climate system, partitioning the energy between the atmosphere and the earth's surface. They also control the loss of energy to space by their effect on thermal emission. Cirrus and altostratus are the most frequent cloud types, having an annual average global coverage of 35 and 40 percent, respectively. Cirrus is composed almost entirely of ice crystals and the same is frequently true of the upper portions of altostratus since they are often formed by the thickening of cirrostratus and by the spreading of the middle or upper portions of thunderstorms. Thus, since ice clouds cover such a large portion of the earth's surface, they almost certainly have an important effect on climate. With this recognition, researchers developing climate models are seeking largely unavailable methods for specifying the conditions for ice cloud formation, and quantifying the spatial distribution of ice water content, IWC, a necessary step in deriving their radiative characteristics since radiative properties are apparently related to IWC. A method is developed for specifying IWC in climate models, based on theory and measurements in cirrus during FIRE and other experiments.

Heymsfield, Andrew J.↗
NASA NTRS1991

Solar rocket plume/mirror interactions

The extent to which the plume from a solar thermal rocket will impinge on the solar collector is studied by flow field analysis. Such interaction can adversely affect collector performance through fouling, excessive heat loading, or pressure loads that deform the delicate structures. The geometrical shape of the collector is such that only the flow from the nozzle boundary layer can reach it, but the thrust levels of interest lead to very viscous nozzle flows with thick boundary layers. Reasonable accuracy in solving these flows requires a fully coupled viscous-inviscid procedure. Results show that the fraction of the plume that hits the collector can be well estimated by continuum theory, but that transitional and rarefied phenomena will have some impact on how it is distributed over the surface. Initial results for one representative condition show that approx. 4 percent of the total flow in the jet makes its way to the collector. The pressures on the collector, however, remain quite low because of its distance from the engine. Additional work is needed to document the effect of thrust scaling and wall cooling on impingement.

Yu, Sheng-Tao↗
NASA NTRS1990

Relaxation of the loss-cone by quasi-linear diffusion of the electron-cyclotron maser instability in the solar corona

A self-consistent numeric two-dimensional code using kinetic-wave particle equations has been developed and applied to the maser dynamics of the solar corona. Time histories generated by the code reveal details of the evolution of the linear phase, the saturation and subsequent relaxation of the loss cone. Quantitative values are obtained for the saturation time, the amount of the converted free energy, the critical wave energy level for onset of maser diffusion, the velocity and pitch angle range of the resonant particles, and the relative importance of the different magnetoionic modes and harmonics. A wide range of initial conditions is covered by varying the loss-cone distribution and the ambient cold plasma parameters.

Aschwanden, Markus J.↗
NASA NTRS1992

Infrared photometric behavior and opposition effect of Mars

Although the instrument wasn't designed for this purpose, data from the imaging spectrometer ISM may be used for studying photometric variations of Mars reflectance, that are related to the surface materials and aerosols physical properties. ISM flew aboard the Phobos-2 spacecraft which orbited Mars from January to March, 1989. About 40,000 spectra were acquired in 128 channels ranging from 0.76 to 3.16 micro-m, with a spatial resolution of 25 km and a signal-to-noise ratio ranging up to 1000. Analysis of the results leads to the following conclusions: width variations of the opposition surge can be related to differences in porosity or grain size distribution on the various domains, with little or no effect from suspended dust. As the biggest effects are observed on dark and bright materials, intermediate behaviors on average-bright regions cannot result from a mixing process, but are more likely to come from either cementation processes or modification of the grain size distribution under the influence of wind, which under Martian conditions preferentially removes the biggest particles. Thus, a surface dust consisting in big bright and small dark grains could explain the observations.

Erard, S.↗
NASA NTRS1992

Finite element nonlinear panel flutter with arbitrary temperatures in supersonic flow

A finite element frequency domain method for predicting nonlinear flutter response of panels with temperature effects is presented. By using the principle of virtual work, the element nonlinear stiffness formulation for a panel under a combined thermal and aerodynamic loads is derived on the bases of von Karman's large deflection plate theory, the first-order piston theory aerodynamics and the quasi-steady thermal stress theory. The system equations of motion can be mathematically separated into two sets of equations and then solved in sequence. The first set of equations yields the panel thermal-aerodynamic equilibrium and the second set of equations of motion leads to the flutter limit-cycle oscillations. Stability and flutter boundaries can also be obtained from the two sets of system equations. Finite element large amplitude limit-cycle flutter results at different uniform temperatures are obtained for a simply supported square panel and are compared with existing Galerkin/time integration and other finite element solutions. Effects of nonuniform temperature distributions, panel length-to-width ratios, and boundary conditions on flutter responses of rectangular and triangular panels are presented.

Xue, David Y.↗
NASA NTRS1992

Numerical simulation of MPD thruster flows with anomalous transport

Anomalous transport effects in an Ar self-field coaxial MPD thruster are presently studied by means of a fully 2D two-fluid numerical code; its calculations are extended to a range of typical operating conditions. An effort is made to compare the spatial distribution of the steady state flow and field properties and thruster power-dissipation values for simulation runs with and without anomalous transport. A conductivity law based on the nonlinear saturation of lower hybrid current-driven instability is used for the calculations. Anomalous-transport simulation runs have indicated that the resistivity in specific areas of the discharge is significantly higher than that calculated in classical runs.

Caldo, Giuliano↗
NASA NTRS1992

Lunar PMAD technology assessment

This report documents an initial set of power conditioning models created to generate 'ballpark' power management and distribution (PMAD) component mass and size estimates. It contains converter, rectifier, inverter, transformer, remote bus isolator (RBI), and remote power controller (RPC) models. These models allow certain studies to be performed; however, additional models are required to assess a full range of PMAD alternatives. The intent is to eventually form a library of PMAD models that will allow system designers to evaluate various power system architectures and distribution techniques quickly and consistently. The models in this report are designed primarily for space exploration initiative (SEI) missions requiring continuous power and supporting manned operations. The mass estimates were developed by identifying the stages in a component and obtaining mass breakdowns for these stages from near term electronic hardware elements. Technology advances were then incorporated to generate hardware masses consistent with the 2000 to 2010 time period. The mass of a complete component is computed by algorithms that calculate the masses of the component stages, control and monitoring, enclosure, and thermal management subsystem.

Metcalf, Kenneth J.↗
NASA NTRS1993

Vibration of thermally buckled composite plates with initial deflections using triangular elements

A consistent finite element formulation is presented for the analysis of thermal postbuckling and free vibration of thermally buckled thin, laminated composite plates subjected to large temperature change. The influence of moderately large initial imperfections in deflection on the thermal postbuckling deflection and the vibration characteristics of the buckled plate is also investigated. The finite element equations of motion are derived from the principle of virtual work. These equations can be mathematically separated into two sets and solved in sequence. The first set of equations yields the particular solution of static thermal postbuckling deflection, and the second set of equations gives the homogeneous solution of vibration characteristics on the buckled plate. The first set of static equations is solved by using Newton-Raphson iteration method. The tangent stiffness matrix in the final iteration is equal to the total stiffness matrix of the second set of dynamic equations. This feature saves tremendous computation time in comparing with using the conventional approach. The influence of lamination angle, temperature distribution, plate planform of arbitrary shape, and boundary support conditions on postbuckling and vibration behavior are investigated.

Zhou, R. C.↗
NASA NTRS1993

A laboratory model of a hydrogen/oxygen engine for combustion and nozzle studies

A small laboratory diagnostic thruster was developed in order to evaluate approaches for the use of temperature and pressure sensors for the investigation of low thrust rocket flowfields. Tests were performed at chamber pressures of about 255 kPa, 370 kPa, and 500 kPa with oxidizer/fuel mixture ratios between 4.0 and 8.0. Two gaseous hydrogen/gaseous oxygen injector designs were tested with 60 and 75 fuel film cooling. The results of hot-wire tests showed the thruster and instrumentation designs to be effective. Azimuthal temperature distributions were found to be a function of operating conditions and hardware configuration. Results indicated that small differences in injector design can result in dramatically different thruster performance and wall temperature behavior. However, the importance of these injector effects may be decreased by operating at a high fuel film cooling rate.

Morren, Sybil H.↗
NASA NTRS1957

Investigation of the Laminar Aerodynamic Heat-transfer Characteristics of a Hemisphere-cylinder in the Langley 11-inch Hypersonic Tunnel at a Mach Number of 6.8

A program to investigate the aerodynamic heat transfer of a nonisothermal hemisphere-cylinder has been conducted in the Langley 11-inch hypersonic tunnel at a Mach number of 6.8 and a Reynolds number from approximately 0.14 x 10(6) to 1.06 x 10(6) based on diameter and free-stream conditions. The experimental heat-transfer coefficients were slightly less over the whole body than those predicted by the theory of Stine and Wanlass (NACA technical note 3344) for an isothermal surface. For stations within 45 degrees of the stagnation point the heat-transfer coefficients could be correlated by a single relation between local Stanton number and local Reynolds number. Pitot pressure profiles taken at a Mach number of 6.8 on a hemisphere-cylinder have verified that the local Mach number or velocity outside the boundary layer required in the theories may be computed from the surface pressures by using isentropic flow relations and conditions immediately behind a normal shock. The experimental pressure distribution at Mach number of 6.8 is closely predicted by the modified Newtonian theory.

Crawford, Davis H↗
NASA NTRS1993

Dynamic data distributions in Vienna Fortran

Vienna Fortran is a machine-independent language extension of Fortran, which is based upon the Single-Program-Multiple-Data (SPMD) paradigm and allows the user to write programs for distributed-memory systems using global addresses. The language features focus mainly on the issue of distributing data across virtual processor structures. Those features of Vienna Fortran that allow the data distributions of arrays to change dynamically, depending on runtime conditions are discussed. The relevant language features are discussed, their implementation is outlined, and how they may be used in applications is described.

Chapman, Barbara↗