Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Behavior modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,567 records · Page 87

He-3 and other lunar volatiles

Constraints are considered and estimates are given for the abundances of He-3, other noble gases, and chemically reactive volatiles (e.g., H, C, N, S, F, Cl) on the Moon. For the case of surface inventories, solar wind particles implanted into grains on the surface of the Moon provide an accessible, though not necessarily abundant, source of H, C, N and the noble gases. Solar wind implanted species are concentrated in the infest grain sized, and are only found in the upper few meters of the regolith, where there are grains that have been directly exposed to the Sun. Elemental abundances in surface soils are typically 10s of mg/g, and vary according to the exposure history of the soil. The abundance of the rare, but possibly economically important, isotope He-3 is typically a few mg/g. The largest uncertainty in estimates of the total lunar abundance of solar wind implanted species comes from the lack of knowledge of their distribution with depth below the upper meter or two. For the case of bulk inventories, constraints resulting from lunar sample analyses and from physical chemical models of volatile behavior during the hypothesized giant impact origin of the Moon is used to give estimated abundances.

Fegley, B., Jr.↗

Breakup of a liquid jet in supersonic crossflow

A theoretical study of the breakup of a circular liquid jet injected transversely into a supersonic air stream is conducted. Two different criteria for breakup are explored in the context of a previously developed model for the behavior of liquid jets in compressible crossflow (Heister et al., 1989). The local sonic point criterion first proposed by Schetz, et al. (1980) is explored, in addition to an auxiliary criterion put forth by Clark (1964) based on surface-tension stability. It is found that the local sonic point appears to provide a more reasonable approximation to the actual location of jet breakup, based on comparisons with limited experimental data.

Li, H.-S.↗

Stability analysis of position and force control problems for robot arms

Stability issues involving the control of a robot arm under the influence of external forces are discussed. Several different scenarios are considered: position control with the external force as an unmodeled disturbance, compliant control for a bounded external force in some subspace, and compliant control for a force due to the interaction with an environment whose dynamical behavior can be modeled. In each of these cases, a stability analysis using the Lyapunov method is presented. An explanation of instability is put forth for the case in which the environment has flexibility and the gains are inappropriately chosen. When the environment is stiff in the force control subspace, robust stability can be achieved with the integral force feedback.

Wen, John T.↗

Diskoseismology: Probing accretion disks. I - Trapped adiabatic oscillations

The normal modes of acoustic oscillations within thin accretion disks which are terminated by an innermost stable orbit around a slowly rotating black hole or weakly magnetized compact neutron star are analyzed. The dominant relativistic effects which allow modes to be trapped within the inner region of the disk are approximated via a modified Newtonian potential. A general formalism is developed for investigating the adiabatic oscillations of arbitrary unperturbed disk models. The generic behavior is explored by way of an expansion of the Lagrangian displacement about the plane of symmetry and by assuming separable solutions with the same radial wavelength for the horizontal and vertical perturbations. The lowest eigenfrequencies and eigenfunctions of a particular set of radial and quadrupole modes which have minimum motion normal for the plane are obtained. These modes correspond to the standard dispersion relation of disk theory.

Nowak, Michael A.↗

Statistical prediction with Kanerva's sparse distributed memory

A new viewpoint of the processing performed by Kanerva's sparse distributed memory (SDM) is presented. In conditions of near- or over-capacity, where the associative-memory behavior of the model breaks down, the processing performed by the model can be interpreted as that of a statistical predictor. Mathematical results are presented which serve as the framework for a new statistical viewpoint of sparse distributed memory and for which the standard formulation of SDM is a special case. This viewpoint suggests possible enhancements to the SDM model, including a procedure for improving the predictiveness of the system based on Holland's work with genetic algorithms, and a method for improving the capacity of SDM even when used as an associative memory.

Rogers, David↗

A finite element method for the thermochemical decomposition of polymeric materials. I - Theory

The governing differential equations are developed to model the thermomechanical behavior of chemically decomposing, polymeric materials. These equations account for thermal and gaseous diffusion through a poroelastic, transversely isotropic solid. The Bubnov-Galerkin finite element method is applied to the governing equations to cast the coupled set into a single matrix equation. A method for solving these equations simultaneously at each time step is discussed.

Sullivan, R. M.↗

Assessing the impact of modeling limits on intelligent systems

The knowledge bases underlying intelligent systems are validated. A general conceptual framework is provided for considering the roles in intelligent systems of models of physical, behavioral, and operational phenomena. A methodology is described for identifing limits in particular intelligent systems, and the use of the methodology is illustrated via an experimental evaluation of the pilot-vehicle interface within the Pilot's Associate. The requirements and functionality are outlined for a computer based knowledge engineering environment which would embody the approach advocated and illustrated in earlier discussions. Issues considered include the specific benefits of this functionality, the potential breadth of applicability, and technical feasibility.

Rouse, William B.↗

Experiments with phase change thermal energy storage canisters for Space Station Freedom

The solar dynamic power module proposed for the Space Station Freedom (SSF) uses the heat of fusion of a phase change material (PCM) to efficiently store thermal energy for use during eclipse periods. The PCM, a LiF-20CaF2 salt, is contained in annular, metal canisters located in a heat receiver at the focus of a solar concentrator. PCM canister ground-based experiments and analytical heat transfer studies are discussed. The hardware, test procedures, and test results from these experiments are discussed. After more than 900 simulated SSF orbital cycles, no canister cracks or leaks were observed and all data were successfully collected. The effect of 1-g test orientation on canister wall temperatures was generally small while void position was strongly dependent on test orientation and canister cooling. In one test orientation, alternating wall temperature data were measured that supports an earlier theory of oscillating vortex flow in the PCM melt. Analytical canister wall temperatures compared very favorably with experimental temperature data. This illustrates that ground-based canister thermal performance can be predicted well by analyses that employ straight-forward, engineering models of void behavior and liquid PCM free convection.

Kerslake, Thomas W.↗

X-Ray And Acoustic Measurements Yield Stiffnesses

Analytical technique combines ultrasonic scanning measurements of local velocity of sound in specimen of material with x-ray computed tomographic measurements of local mass density to compute local stiffness of material. Stiffnesses at various locations in specimen then used in finite-element mathematical model of elastic behavior of specimen to compute local stresses, local strains, and overall deformations. Technique enhances value of quantitative nondestructive x-ray and ultrasonic measurements. Especially useful in characterization of carbon/carbon composites and other advanced materials not homogeneous and for which customary simplifying assumption of constant density and/or constant stiffness not valid.

Madaras, Eric Irvine↗

Framework Programmable Platform for the Advanced Software Development Workstation (FPP/ASDW). Demonstration framework document. Volume 2: Framework process description

In the second volume of the Demonstration Framework Document, the graphical representation of the demonstration framework is given. This second document was created to facilitate the reading and comprehension of the demonstration framework. It is designed to be viewed in parallel with Section 4.2 of the first volume to help give a picture of the relationships between the UOB's (Unit of Behavior) of the model. The model is quite large and the design team felt that this form of presentation would make it easier for the reader to get a feel for the processes described in this document. The IDEF3 (Process Description Capture Method) diagrams of the processes of an Information System Development are presented. Volume 1 describes the processes and the agents involved with each process, while this volume graphically shows the precedence relationships among the processes.

Mayer, Richard J.↗

Design of a compliant wheel for a miniature rover to be used on Mars

The Jet Propulsion Laboratory has identified the need for a compliant wheel for a miniature martian rover vehicle. This wheel must meet requirements of minimum mass, linear radial deflection, and reliability in cryogenic conditions over a five year lifespan. Additionally, axial and tangential deflections must be no more than 10 percent of the radial value. The team designed a wheel by use of finite element and dimensionless parameter analysis. Due to the complex geometry of the wheel, a finite element model describing its behavior was constructed to investigate different wheel configurations. Axial and tangential deflections were greatly reduced but did not meet design criteria. A composite material was selected for its high strength, toughness, fatigue resistance, and damping characteristics. The team chose a Kevlar fiber filled thermoplastic composite. This report is divided into four primary sections. First, the introduction section gives background information, defines the task, and discusses the scope and limitations of the project. Second, the alternative designs section introduces alternative design solutions, addresses advantages and disadvantages of each, and identifies the parameters used to determine the best design. Third, the design solution section introduces the methods used to evaluate the alternates, and gives a description of the design process used. Finally, the conclusion and recommendations section evaluates the wheel design, and offers recommendations pertaining to improvement of the design solution.

Carroll, Mark↗

A Regression Method for Comparing Launch Zone Ranges Derived From Different Sources

In modern fighter aircraft air-to-air missile launch acceptable ranges (LARs) are provided to the pilot for his launch decision. These LARs are calculated in the avionic software, using very simple algebraic equations and algorithms, that attempt to model complex missile behavior. Frequently these algorithms are revised to reflect inaccuracies discovered, when comparisons are made with missile six degree-of-freedom (6-DOF) simulations. The process of modifying this software has become expensive. In the past, these simple LAR generators were modified based only on subjective judgmental approach, with little regard to the missile range design limits. With reduced budgets a more rational methodology should be taken to assess whether or not simple fighter LAR generators need to be modified. Any LAR generator can produce large amounts of range (minimum and maximum) data over the board engagement limits of modem fighter and air-to-air missiles. This infinite population lends itself to some statistical methodology to access simple LAR accuracy and the need for software modification. The methodology should produce statistical parameters for use in the decision making process of modifying a simple fighter LAR generator. This paper presents a regression method, based on a missile range design limit philosophy. Acceptance criteria from the regression method are given that provide simple statistical parameters to aid in this decision making process.

Flight Testing↗

Nondestructive evaluation of Shuttle Columbia tiles

The NDE of Orbiter Vehicle-102 tile bonds, performed in August 1991, is described. The evaluation was carried out in order to help NASA develop fast, reliable methods to diagnose problems in tile bonding other than the present 'pull' and 'wiggle' tests. The NDE did not find any indication of bond problems, and all bonds were classified as 'nominal'. The feasibility of using NDE techniques in a dynamic, real-world environment without interfering with Shuttle rework schedules is shown. The data will be useful in verifying analytical models of tile behavior developed at the University of Central Florida. The need for a tile test bed containing known tile misbonds is suggested.

Davis, Richard M.↗

Hidden slow pulsars in binaries

The recent discovery of the binary containing the slow pulsar PSR 1718-19 orbiting around a low-mass companion star adds new light on the characteristics of binary pulsars. The properties of the radio eclipses of PSR 1718-19 are the most striking observational characteristics of this system. The surface of the companion star produces a mass outflow which leaves only a small 'window' in orbital phase for the detection of PSR 1718-19 around 400 MHz. At this observing frequency, PSR 1718-19 is clearly observable only for about 1 hr out of the total 6.2 hr orbital period. The aim of this Letter is twofold: (1) to model the hydrodynamical behavior of the eclipsing material from the companion star of PSR 1718-19 and (2) to argue that a population of binary slow pulsars might have escaped detection in pulsar surveys carried out at 400 MHz. The possible existence of a population of partially or totally hidden slow pulsars in binaries will have a strong impact on current theories of binary evolution of neutron stars.

Tavani, Marco↗

The 1987 RIACS annual report

The Research Institute for Advanced Computer Science (RIACS) was established at the NASA Ames Research Center in June of 1983. RIACS is privately operated by the Universities Space Research Association (USRA), a consortium of 64 universities with graduate programs in the aerospace sciences, under several Cooperative Agreements with NASA. RIACS's goal is to provide preeminent leadership in basic and applied computer science research as partners in support of NASA's goals and missions. In pursuit of this goal, RIACS contributes to several of the grand challenges in science and engineering facing NASA: flying an airplane inside a computer; determining the chemical properties of materials under hostile conditions in the atmospheres of earth and the planets; sending intelligent machines on unmanned space missions; creating a one-world network that makes all scientific resources, including those in space, accessible to all the world's scientists; providing intelligent computational support to all stages of the process of scientific investigation from problem formulation to results dissemination; and developing accurate global models for climatic behavior throughout the world. In working with these challenges, we seek novel architectures, and novel ways to use them, that exploit the potential of parallel and distributed computation and make possible new functions that are beyond the current reach of computing machines. The investigation includes pattern computers as well as the more familiar numeric and symbolic computers, and it includes networked systems of resources distributed around the world. We believe that successful computer science research is interdisciplinary: it is driven by (and drives) important problems in other disciplines. We believe that research should be guided by a clear long-term vision with planned milestones. And we believe that our environment must foster and exploit innovation. Our activities and accomplishments for the calendar year 1987 and our plans for 1988 are reported.

Source record↗

A Pluto thermal model

The recent discovery of nitrogen on Pluto suggests that Pluto's volatile cycles may be similar to those on Neptune's moon Triton. Here, we report the first results of our efforts to apply a thermal model that we developed to study the seasonal nitrogen cycle on Triton to the case of Pluto. The model predicts volatile behavior as a function of time to calculate frost deposit depth, polar cap boundaries, temperature of the frost and substrate, and atmospheric pressure, assuming nitrogen frost deposits in solid-vapor equilibrium with nitrogen in the atmosphere.

Hansen, C. J.↗

Mobility analysis, simulation, and scale model testing for the design of wheeled planetary rovers

The use of computer based techniques to model and simulate wheeled rovers on rough natural terrains is considered. Physical models of a prototype vehicle can be used to test the correlation of the simulations in scaled testing. The computer approaches include a quasi-static planar or two dimensional analysis and design tool based on the traction necessary for the vehicle to have imminent mobility. The computer program modeled a six by six wheel drive vehicle of original kinematic configuration, called the Rocker Bogie. The Rocker Bogie was optimized using the quasi-static software with respect to its articulation parameters prior to fabrication of a prototype. In another approach used, the dynamics of the Rocker Bogie vehicle in 3-D space was modeled on an engineering workstation using commercial software. The model included the complex and nonlinear interaction of the tire and terrain. The results of the investigation yielded numerical and graphical results of the rover traversing rough terrain on the earth, moon, and Mars. In addition, animations of the rover excursions were also generated. A prototype vehicle was then used in a series of testbed and field experiments. Correspondence was then established between the computer models and the physical model. The results indicated the utility of the quasi-static tool for configurational design, as well as the predictive ability of the 3-D simulation to model the dynamic behavior of the vehicle over short traverses.

Lindemann, Randel A.↗

Containerless measurements on liquids at high temperatures

The application of containerless techniques for measurements of the thermophysical properties of high temperature liquids is reviewed. Recent results obtained in the materials research laboratories at Intersonics are also presented. Work to measure high temperature liquid properties is motivated by both the need for reliable property data for modeling of industrial processes involving molten materials and generation of data form basic modeling of materials behavior. The motivation for this work and examples of variations in thermophysical property values from the literature are presented. The variations may be attributed to changes in the specimen properties caused by chemical changes in the specimen and/or to measurement errors. The two methods used to achieve containerless conditions were aeroacoustic levitation and electromagnetic levitation. Their qualities are presented. The accompanying slides show the layout of levitation equipment and present examples of levitated metallic and ceramic specimens. Containerless techniques provide a high degree of control over specimen chemistry, nucleation and allow precise control of liquid composition to be achieved. Effects of minor additions can thus be measured in a systematic way. Operation in reduced gravity enables enhanced control of liquid motion which can allow measurement of liquid transport properties. Examples of nucleation control, the thermodynamics of oxide contamination removal, and control of the chromium content of liquid aluminum oxide by high temperature containerless processes are presented. The feasibility of measuring temperature, emissivity, liquidus temperature, enthalpy, surface tension, density, viscosity, and thermal diffusivity are discussed in the final section of the paper.

Weber, Richard↗