Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind tunnel testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Long duct nacelle aerodynamic development for DC-10 derivatives

The results are presented of a wind tunnel test utilizing a 4.7-percent-scale semispan model of the DC-10 in the Calspan 8-foot transonic wind tunnel. The effect of a revised long-duct nacelle shape on the channel velocities, the incremental drag relative to the baseline long-duct nacelle, and channel velocities for the baseline long-duct nacelle were determined and compared with data obtained at Ames. The baseline and the revised long-duct nacelles are representative of a CF6-50 mixed-flow configuration and were evaluated on a model of a proposed DC-10 stretched-fuselage configuration. The results showed that the revised long-duct nacelle has an appreciable effect on the inboard channel velocities, resulting in an increased channel Mach number. However, the pressure recovery on the nacelle afterbody was about the same for both nacelles. The lift curves for both long-duct nacelle configurations were the same. The channel pressures measured at Calspan were in good agreement with those measured at Ames for the baseline long-duct nacelle. The incremental drag for the revised nacelle was measured as two to four counts (three counts is approximately equal to one percent of the airplane drag) higher than that of the baseline long-duct nacelle.

Patel, S. P.↗
NASA NTRS1991

Results from a test of a 2/3-scale V-22 rotor and wing in the 40- by 80-Foot Wind Tunnel

A test of a 0.658-scale V-22 rotor and wing was conducted in the 40- by 80-Foot Wind Tunnel at Ames Research Center. The principal objectives of the test were to measure the wing download in hover for a variety of test configurations, and rotor performance in forward flight. Also, a limited amount of data on rotor performance in vertical climb were acquired. This paper presents the results from the test with predictions from appropriate analytical methods. A new method for presenting and interpreting wing surface pressure data in hover is described, and this method shows that the wing flap can produce substantial lift loads in hover. The rotor performance in vertical climb was underpredicted by CAMRAD/JA and by the free wake analysis EHPIC. A simple momentum theory is presented which provides good predictions of rotor performance in forward flight.

Felker, Fort F.↗
NASA NTRSDate not supplied

Wind-US Simulations of the NASA 1507 Inlet Test Case

Steady-state, Reynolds-Averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) simulations were performed of the NASA 1507 Inlet Test Case from the 6th AIAA Propulsion Aerodynamics Workshop (PAW) held in January 2023 using the Wind-US CFD solver. The simulations were performed with bleed regions modeled as surface patches and the Slater bleed boundary condition models were applied within those regions. Both the constant-plenum-pressure and the fixed-plenum-exit bleed models where applied. The vortex generators were modeled using the Bender-Anderson-Yagle (BAY) vortex generator model. The CFD simulations were performed for inlet engine-face flow ratios varying from supercritical to subcritical inlet operation until inlet unstart. The results of the CFD simulations were compared to wind-tunnel data which included boundary layer profiles, axial static pressure distributions, bleed rates, total pressure recovery performance curves, and engine-face total pressure rake profiles. The CFD simulations were able to match most of the boundary layer rake data near the geometric throat, but the boundary layers on the centerbody were thinner than indicated by the wind-tunnel data. For the supercritical CFD simulations, the engine-face flow ratio was at least 2% to 2.5% lower than indicated by the wind-tunnel data, but still consistent with the level of supercritical bleed. The engine-face flow rates of the wind-tunnel tests had an uncertainty of ±2% which could explain the differences. The supercritical engine-face flow rates of the wind-tunnel data indicated a 5% supercritical bleed rate rather than the reported 7.18% bleed rate. The CFD simulations were able to calculate the maximum total pressure recovery of pt2/pt = 0.907 as observed for the wind-tunnel data. The CFD simulations with the constant-pressure bleed model were able to obtain a much lower engine-face total pressure ratio than indicated by both the wind-tunnel data and the CFD simulations using a fixed-plenum-exit bleed model. The CFD simulations indicated a sharp static pressure rise for the terminal shock rather than a more gradual rise indicated by the wind-tunnel data. The CFD simulations were not able to accurately compute the total pressure variation across the engine-face total pressure rake.

Supersonics↗
NASA NTRS1976

High supersonic stability and control characteristics of a 0.015-scale (remotely controlled elevon) model 44-0 space shuttle orbiter tested in the NASA/LaRC 4-foot UPWT (LEG 2) (LA75), volume 1

Wind tunnel tests are reported on a 0.015-scale SSV orbiter model with remote independently operated left and right elevon surfaces. Special attention was directed to definition of nonlinear aerodynamic characteristics by taking data at small increments. Six component aerodynamic force and moment and elevon position data were recorded for the space shuttle orbiter with various elevon, aileron rudder and speed brake deflection combinations over an angle of attack range from -4 deg to 32 deg at angles of sideslip of 0 deg and 3 deg. Additional tests were made over an angle of sideslip range from -6 deg to 8 deg at selected angles of attack. Test Mach numbers were 2.86, 2.90, 3.90 and 4.60 with Reynolds numbers held at a constant 2.0 x 1 million per foot.

Ball, J. W.↗
NASA NTRS1981

Additional testing of the inlets designed for a tandem fan V/STOL nacelle

The wind tunnel testing of a scale model of a tandem fan nacelle designed for a type (subsonic cruise) V/STOL aircraft configuration is discussed. The performance for the isolated front inlet and for the combined front and aft inlets is reported. Model variables include front and aft inlets with aft inlet variations of short and long aft inlet cowls, with a shaft simulator and diffuser vortex generators, cowl lip fillets, and nacelle strakes. Inlet pressure recovery, distortion, and inlet angle-to-attack separation limits were evaluated at tunnel velocity from 0 to 240 knots, angles-of-attack from -10 to +40 degrees and inlet flow rates corresponding to throat Mach number from 0.0 to 0.6. Combined nacelle pitch and yaw runs up to 30 deg. were also made.

Ybarra, A. H.↗
NASA NTRS1942

An Investigation of Hydrofoils in the NACA Tank I : Effect of Dihedral and Depth of Submersion

Tests were conducted on hydrofoil assemblies approximating an arrangement for use under seaplanes or surface boats. A series of hydrofoils, each supported by two struts, was towed at various depths ranging from partial submersions to a depth of 5-chord lengths. At depths greater than 4 or 5 chords, the influence of the surface of the water is small; hydrofoils operating at low speed will have characteristics similar to those of airfoils of the same section.

HYDROFOILS - NACA - CHARACTERISTICS TANK TESTS (NA↗
NASA NTRS1993

Lift enhancement of an airfoil using a Gurney flap and vortex generators

The results of a low-speed wind tunnel test are presented for a single-element airfoil incorporating two lift-enhancing devices, namely a Gurney flap and vortex generators. The former consists of a small plate, on the order of one to two percent of the airfoil chord in height, located at the trailing edge perpendicular to the pressure side of the airfoil. The later consist of commercially-available, wishbone-shaped vortex generators. The test was conducted in the NASA Ames 7- by 10-foot Wind Tunnel with a full-span NACA 4412 airfoil. Measurements of surface pressure distributions and wake profiles were made to determine the lift, drag, and pitching-moment coefficients for the various airfoil configurations. The results indicate that the addition of a Gurney flap increased the maximum lift coefficient from 1.49 up to 1.96.

Storms, Bruce L.↗
NASA NTRS1980

Evaluation of flow quality in two large NASA wind tunnels at transonic speeds

Wind tunnel testing of low drag airfoils and basic transition studies at transonic speeds are designed to provide high quality aerodynamic data at high Reynolds numbers. This requires that the flow quality in facilities used for such research be excellent. To obtain a better understanding of the characteristics of facility disturbances and identification of their sources for possible facility modification, detailed flow quality measurements were made in two prospective NASA wind tunnels. Experimental results are presented of an extensive and systematic flow quality study of the settling chamber, test section, and diffuser in the Langley 8 foot transonic pressure tunnel and the Ames 12 foot pressure wind tunnel. Results indicate that the free stream velocity and pressure fluctuation levels in both facilities are low at subsonic speeds and are so high as to make it difficult to conduct meaningful boundary layer control and transition studies at transonic speeds.

Harvey, W. D.↗
NASA NTRS1981

A theory for predicting boundary impedance and resonance frequencies of slotted-wall wind tunnels, including plenum effects

Wave-induced resonance associated with the geometry of wind-tunnel test sections can occur. A theory that uses acoustic impedance concepts to predict resonance modes in a two dimensional, slotted wall wind tunnel with a plenum chamber is described. The equation derived is consistent with known results for limiting conditions. The computed resonance modes compare well with appropriate experimental data. When the theory is applied to perforated wall test sections, it predicts the experimentally observed closely spaced modes that occur when the wavelength is not long compared with he plenum depth.

Barger, R. L.↗
NASA NTRS1982

Dynamic structural aeroelastic stability testing of the XV-15 tilt rotor research aircraft

For the past 20 years, a significant effort has been made to understand and predict the structural aeroelastic stability characteristics of the tilt rotor concept. Beginning with the rotor-pylon oscillation of the XV-3 aircraft, the problem was identified and then subjected to a series of theoretical studies, plus model and full-scale wind tunnel tests. From this data base, methods were developed to predict the structural aeroelastic stability characteristics of the XV-15 Tilt Rotor Research Aircraft. The predicted aeroelastic characteristics are examined in light of the major parameters effecting rotor-pylon-wing stability. Flight test techniques used to obtain XV-15 aeroelastic stability are described. Flight test results are summarized and compared to the predicted values. Wind tunnel results are compared to flight test results and correlated with predicted values.

Schroers, L. G.↗
NASA NTRS1973

Experimental study of flow about a stalled two-dimensional airfoil

Wind tunnel tests to determine the flow characteristics of a stalled wing are described. The advantages of the plane wing over the ring wing for wind tunnel investigations are presented. The general flow pattern for stalled ring airfoils is developed. Photographs of the test equipment and installation are provided.

Coles, D. E.↗
NASA NTRS2018

Acoustic Testing of a High-Tip-Speed Fan with Bypass-Duct Liners

Under a pair of Space Act Agreements between NASA and Honeywell Aerospace, a model-scale (22 in.-diameter fan) acoustic wind tunnel test was carried out in the fall of 2014 in the NASA Glenn Research Center 9- by 15-Foot Low-Speed Wind Tunnel. The goal was to obtain acoustic pressure measurements for far-field, inlet and exit rotating rake, and in-duct microphone locations. This supersonic-tip-speed fan was tested in three bypass duct configurations: hard-wall, traditional liner, and advanced multiple-degree-of-freedom. Limited aerodynamic data was collected to verify the expected operating conditions. Preliminary analysis of the acoustic data finds it suitable for use in evaluating current NASA and Honeywell Aerospace acoustic tools and liner design practices.

Noise↗
NASA NTRSDate not supplied

NASA’s Unsteady Pressure-Sensitive Paint Phase I Development Overview

Since 2019, a group out of NASA Ames Research Center(ARC)has been focused on implementing systematic updates to make unsteady pressure-sensitive paint (uPSP) a more viable capability for production wind tunnel testing. Focusing on the general categories of data acquisition, data transfer, data processing, and data visualization, the uPSP Development Team has made several improvements to increase data quality and innovate a more workable system that would provide valuable surface pressure data to customers. As a result of the COVID-19 pandemic and several initial demonstration tests prior to the formal start of the development effort, the decision was made to focus on launch vehicles as the test article. To-date this development has focused on implementation in the ARC Unitary Plan Wind Tunnel 11-by11-footTransonic Wind Tunnel due to the large optical access of the test section and that the NASA Advanced Supercomputer is located at ARC. This paper summarizes the project origins and the results of four years of development effort, which will all culminate in a final demonstration test in the first half of2024.

unsteady pressure-sensitive paint↗
NASA NTRS1998

Flight Stability and Control and Performance Results from the Linear Aerospike SR-71 Experiment (LASRE)

The Linear Aerospike SR-71 Experiment (LASRE) is presently being conducted to test a 20-percent-scale version of the Linear Aerospike rocket engine. This rocket engine has been chosen to power the X-33 Single Stage to Orbit Technology Demonstrator Vehicle. The rocket engine was integrated into a lifting body configuration and mounted to the upper surface of an SR-71 aircraft. This paper presents stability and control results and performance results from the envelope expansion flight tests of the LASRE configuration up to Mach 1.8 and compares the results with wind tunnel predictions. Longitudinal stability and elevator control effectiveness were well-predicted from wind tunnel tests. Zero-lift pitching moment was mispredicted transonically. Directional stability, dihedral stability, and rudder effectiveness were overpredicted. The SR-71 handling qualities were never significantly impacted as a result of the missed predictions. Performance results confirmed the large amount of wind-tunnel-predicted transonic drag for the LASRE configuration. This drag increase made the performance of the vehicle so poor that acceleration through transonic Mach numbers could not be achieved on a hot day without depleting the available fuel.

Moes, Timothy R.↗
NASA NTRS1985

An experimental and analytical method for approximate determination of the tilt rotor research aircraft rotor/wing download

The XV-15 Tilt Rotor Research Aircraft download phenomenon was analyzed. This phenomenon is a direct result of the two rotor wakes impinging on the wing upper surface when the aircraft is in the hover configuration. For this study the analysis proceeded along tow lines. First was a method whereby results from actual hover tests of the XV-15 aircraft were combined with drag coefficient results from wind tunnel tests of a wing that was representative of the aircraft wing. Second, an analytical method was used that modeled that airflow caused gy the two rotors. Formulas were developed in such a way that acomputer program could be used to calculate the axial velocities were then used in conjunction with the aforementioned wind tunnel drag coefficinet results to produce download values. An attempt was made to validate the analytical results by modeling a model rotor system for which direct download values were determinrd..

Jordon, D. E.↗
NASA NTRS2019

Acoustic Testing of a High-Tip-Speed Fan with Bypass-Duct Liners - Overview

Under a pair of Space Act Agreements between NASA and Honeywell Aerospace, a model-scale (22 in.-diameter fan) acoustic wind tunnel test was carried out in the fall of 2014 in the NASA Glenn Research Center 9- by 15-Foot Low-Speed Wind Tunnel. The goal was to obtain acoustic pressure measurements for far-field, inlet and exit rotating rake, and in-duct microphone locations. This supersonic-tip-speed fan was tested in three bypass duct configurations: hard-wall, traditional liner, and advanced multiple-degree-of-freedom. Limited aerodynamic data was collected to verify the expected operating conditions. Preliminary analysis of the acoustic data finds it suitable for use in evaluating current NASA and Honeywell Aerospace acoustic tools and liner design practices. This report provides an overview of the test and some preliminary findings.

Miller, Christopher J.↗