Results for “torque” — Page 86

NASA NTRSDate not supplied

Attitude Control System for the Solar Cruiser and Future Solar Sail Missions

NASA’s Marshall Space Flight Center (MSFC) is developing the Solar Cruiser solar sail mission to continue to mature solar sail propulsion. Solar Cruiser is a 95kg spacecraft capable of deploying a 1654 square meter solar sail. Solar Cruiser will demonstrate science observation capabilities and navigation in sub Lagrange Point (L1) halo-orbits. Solar Cruiser sail technology can be scaled to larger solar sail missions, including attitude control system and sail membrane and boom technology. Larger solar sails could be used to image the solar poles, enabling Solar Polar Imager (SPI) missions currently prohibitively expensive for propellant-based propulsion methods. Similarly, solar sails can be used to create artificial equilibria and indefinite station-keeping at locations sunward of Lagrange Point one, L1, along the Sun-Earth line (SEL), which can provide space-weather monitor and prediction and reveal discoveries about our Sun and solar system. To achieve the high characteristic acceleration required for larger solar sail missions such as SPI, a solar sail area of approximately 7000 square-meters would be needed. In comparison, the largest solar sail flown to date is the JAXA’s IKAROS mission with a 196 square-meters sail. Attitude control an SPI-size sail poses challenges, including station keeping under solar sail induced torques and thrust vector pointing. In this study, the scalability of the Solar Cruiser sail attitude control architecture to larger sails is studied, such as pointing control performance, mass and power requirements. Solar Cruiser attitude control actuators include propellant-based, such as ion engines, and propellantless options which create differential solar pressures to generate spacecraft torques. Propellantless attitude control includes active translation of the center of mass, Reflectivity Control Devices (RCDs), and tip vanes. The study summarizes the scalability characteristics of the different attitude control architectures for larger solar sail missions.

Solar Sail Propulsion↗

NASA NTRS2018

Modeling of Orbital and Attitude Dynamics of Nanosatellites Controlled via Active Electrostatic Charging

The large-scale exploration of airless bodies, such as asteroids and moons, is gaining interest, however it is limited by mobility issues: the lack of atmosphere, low gravity, and unknown soil properties pose difficult challenges for many forms of traditional locomotion. The environment in proximity of these bodies is also electrically charged due to interactions with solar wind and UV radiation. The EGlider (Electrostatic Glider) concept would be able to overcome these mobility issues by leveraging the natural environment, allowing operations in close proximity of the surface, while enabling long duration missions by minimizing propellant consumption. The EGlider is an advanced concept for small satellite mobility and propulsion, which relies on the electric fields naturally present around airless bodies in order to generate forces and torques useful for maneuvering. It does so by extending electrically charged appendages, which enable it to electrostatically soar above the surface. By differentially charging its electrodes it can also produce torques to control its attitude. The charges are maintained by continuous active ion or electron emission from the spacecraft, in order to cancel out the neutralizing influx of charges from surrounding plasma. An investigation of the spacecraft-plasma interaction was carried out. This included studying the effect of electrode geometry and calculating the charge-to-mass ratios required to enable several mission scenarios. Long, thin wire electrodes were identified to be the most power-efficient and would allow power-to-weight ratios achievable with current nanosatellite technologies. High electrode potential represents the main limiting factor for the system design. In order to test the feasibility of active control by means of differential charging, a simple 2D interaction model was developed, and a feedback controller to stabilize the vehicle was tested in a simulation environment. The results confirmed that good performance could be obtained for both position and attitude control. Finally, a dedicated software was developed for future simulation and testing of control strategies for the EGlider. This software allows to study the trajectory and attitude of an arbitrarily configured spacecraft in the proximity of an arbitrarily defined main airless body. The spacecraft can be assembled from basic parts, each with specified electrical, mass and optical properties. Efficient models allow to calculate gravitational and electrical interactions with the rotating main body and the local plasma field, as well as solar radiation pressure effects. Control models can be implemented as simple plug-in functions and easily tested. The preliminary validation campaign showed good matching with the reference cases that have been analyzed.

Corpino, Sabrina↗

NASA NTRSDate not supplied

Full Scale Flat Floor Testing of a 500-M2-Class Solar Sail Deployer

Solar sailing missions rely on deployable systemsfor large area to mass ratios once in space, whilestill being small enough for launcher envelopes inthe stowed configuration. Many of thesedeployable systems feature booms that areflattened and subsequently coiled onto aspool/hub. As part of a collaborative deployablespace structures research effort of NASA and DLR,a boom deployment mechanism for a future 500 m²solar sail has been developed since 2017. To achieve the respective solar sail size goal, 16.5m long booms produced by NASA were integratedinto a DLR-designed deployer mechanism. Thisconsiderable size, as well as the lightweightconstruction of the booms and respectivedeployable systems makes ground testing asignificant challenge. Some systems for gravitycompensation and boom alignment will bepresented in the paper. However, the main focus isthe functional flat floor testing of the integratedboom-deployment mechanism system, as well asits challenges. The testing performed includes full deployment aswell as stowage of the booms. Both have beenperformed multiple times. The latter is one of thekey parameters determining packaging efficiency,which in turn confirms design assumptions. Duringsystem development, small scale tests and modelshave been used in preparation of flat floor testingof the 33 m span cross of the full-scale booms anddeployment mechanism. Hence a small chapter isalso devoted to analysing the differences inbehaviour between small- and full-scaledeployment systems. More parameters that are vital to design decisionshave been determined this way, such as drivingbelt force or hub brake torque. This paper alsofocuses on development goals and needs forfuture steps to achieve higher levels of technologyreadiness, such as the balancing of driving motorforce, synchronisation of its transmission and thecountering hub brake torque

Deployment mechanism↗

NASA NTRS2022

Environmental Testing of the OVEN System for Lunar Water Extraction and Prospecting

Introduction: The presence of water ice in permanently shadowed regions on the lunar surface [1] may enable a sustained human presence on the Moon with minimal need for consumables. However, in order to develop a long term utilization plan that includes the usage of in-situ water we must first understand the abundance, stratigraphy and distribution of this re-source. Multiple space agencies currently have plans for lunar water prospecting missions. The Optimized Volatile Extraction Node (OVEN) was designed for water prospecting missions that require samples to be weighed, sealed, and heated as the means of determining water concentration. This method of water quantification necessitates a fair amount of automation, so a rigorous environmental test program was performed in order to build confidence in the performance of the OVEN design. The work presented here describes the OVEN environmental test program as well as ongoing efforts to improve on the design. Vibration: The OVEN participated in two rounds of random vibration tests. The first test was a stand-alone test performed at the Energy Systems Test Area of the Johnson Space Center. The second test was an integrated test with the mobile platform developed for the Resource Prospector project. The OVEN survived both tests without damage, but the tests did provide valuable lessons learned with regards to specific operations. Thermal Vacuum: The OVEN was successfully demonstrated at a temperature range of -50 to 75 C in a thermal vacuum chamber. The need to heat motor gearboxes at lower temperatures was predetermined so this test program was completed by implementing a method of gearbox heating that used the existing circuitry within the motors. Dust: A custom dynamometer was built in order to determine the torque required to move the various mechanisms within the OVEN at a range of temperatures. The OVEN system was coated with lunar dust simulant in order to determine mechanism torques under a worst-case operating condition. Sublimation: Sublimation losses within the OVEN were quantified through a series of test configurations, including an integrated test in a thermal vacuum chamber at Glenn Research Center [2]. Current Work: The OVEN subsystem is currently not a component of any existing prospecting missions, but work continues that will take the lessons learned from previous environmental tests and improve on the design in order to be considered for future prospecting opportunities. References: [1] Colaprete, A., Schultz, P., Heldmann, J., Wooden, D., Shirley, M., Ennico, K., ... & Sollitt, L. (2010). Detection of water in the LCROSS ejecta plume. science, 330(6003), 463-468. [2] Kleinhenz, J., Smith, J., Roush, T., Colaprete, A., Zacny, K., Paulsen, G., ... & Paz, A. (2018). Volatiles Loss from water bearing regolith simulant at Lunar Environments. In Earth and Space 2018: Engineering for Extreme Environments (pp. 454-466). Reston, VA: American Society of Civil Engineers.

A Paz↗

NASA NTRSDate not supplied

X-57 “Maxwell” High-Lift Propeller Testing and Model Development

NASA’s X-57 “Maxwell” distributed electric propulsion flight demonstrator has a high-lift system that includes 12 fixed-pitch high-lift propellers located upstream of the wing leading edge for lift augmentation at low speeds. These high-lift propellers are not required at higher speeds and are folded conformally along the nacelles to reduce drag when not in operation. Aircraft performance models and flight simulations incorporate propeller performance to predict thrust, moments, and power consumption and propeller model accuracy is important in identifying safe operating regimes for this aircraft. Current high-lift propeller performance models have been verified and calibrated against numerous computational fluid dynamics analyses under a variety of flight conditions. We performed a series of full-scale wind tunnel tests at the NASA Langley Research Center Low Speed Aeroacoustic Wind Tunnel to further validate these models, to identify any adverse operating conditions for these propellers, and to assess the accuracy of the facility’s new Propeller Test Stand. The results indicate that the models accurately predicted performance and that the right-handed propeller showed lower torque and thrust for a given propeller speed compared to the left-handed version. Acoustic data support these measurements, showing higher tonal noise for the left versus right propeller. We suspect this is due to slight differences in the material properties between the early production (right) and more recent (left) blade sets leading to greater detwisting in the right-handed blades under load. Both propellers demonstrated very stable operation throughout the test including during deployment, stowing, and windmilling. Furthermore, high-speed imagery of the spinning propeller indicated no blade oscillations or instabilities for any test case. We also leveraged these images to analyze the effects of propeller loading on blade detwisting and tip position. Unfortunately, the thrust measurements varied significantly during the test due to cross-loading of the Propeller Test Stand load cell, though trends in the thrust data were still observable. The torque measurement, however, remained very precise for all test points and was used for performance comparisons. As a result of this test, we validated and improved the X-57 high-lift propeller performance models, obtained detailed propeller acoustic data and high-speed imagery, observed the propeller operating safely during a variety of dynamic events, and identified two potentially adverse, low-propeller-speed conditions which will be avoided during normal aircraft operation.

X-57↗

NASA NTRSDate not supplied

ISRU Pilot Excavator: Bucket Drum Scaling Experimental Results

NASA’s Space Technology Mission Directorate (STMD) is funding the development of a robotic excavator called the “ISRU Pilot Excavator” which will be a technology demonstration of excavating and transporting 10 metric tons of lunar regolith on the surface of the moon with a 30k-class robotic excavator. ISRU Pilot Excavator will be the next generation of robotic excavator to use bucket drums as excavation tools. This is an evolution of the Regolith Advanced Surface Systems Operations Robot (RASSOR) developed at NASA’s Kennedy Space Center. Bucket drums are hollow cylinders with regularly spaced scoops around the perimeter. The drums rotate in one direction to collect regolith with the scoops. The regolith slides down an internal baffling system inside the drum which prevents the regolith from falling back out of the scoops. The captured regolith can then be transported while held in the drum and then deposited by rotating the drum in the opposite direction allowing the regolith to slide back down the baffling and out of the excavation scoops. Bucket drums were developed by Lockheed Martin in 2008 and used on multiple robotic excavator prototypes ever since. However the forces on a bucket drum and considerations for scaling have not been measured in detail. Bucket drums are challenging to model using classical blade\bucket equations because of their unique geometry. Therefore this experiment was performed to measure the forces on three bucket drums of the same geometry at different scales. Small: 9.4” (239mm) dia. x 8.1” (206mm) width, Medium: 11.6” (294mm) dia. x 10” (254mm) width, and Large: 17” (432mm) dia. x 14.1”(358mm) width. The test stand consisted of an actuated gantry with controlled motion in the vertical (Z) and horizontal (X) axes and a single rotation axis (R). The bucket drums were individually mounted to the rotary axis of the test stand and translated across a prepared bed of BP-1 lunar regolith simulant at a specified linear speed and cutting depth. The test stand was outfitted with a torque sensor in line with the rotation of the drum (R) and a 3 axis (X, Y, and Z) load cell. In addition to the three sizes of bucket drums the linear excavation speed and cutting depth were test variables. The results of these experiments show the relationship between the three scales of bucket drums for factors such as: excavation force, torque due to regolith rotation inside the drum, excavation energy, time to fill, etc. and will be discussed in detail in this paper. This fundamental data will be used in the design of the ISRU Pilot Excavator and can inform the design of future bucket drum excavators.

Jason Michael Schuler↗

NASA NTRSDate not supplied

Characterizations of Optimized Microshutter Arrays for Space Borne Observatory Applications

We report the latest design, fabrication, and characterization result of the Next-Generation Microshutter Arrays (NGMSA) for space borne observatory applications. Our improved blade design aims to reduce the counter torque induced by the potential on the opposing wall to eliminate the torque bump, and thus enables pure electrostatic actuation for more reliable and stable microshutter operations. This paper presents the experimental performances of micro-fabricated microshutter arrays with varying design parameters and compares the results with simulation predictions.

Electrostatic↗

NASA NTRSDate not supplied

ISRU Pilot Excavator: Bucket Drum Scaling Experimental Results

NASA’s Space Technology Mission Directorate (STMD) is funding the development of a robotic excavator called the “ISRU Pilot Excavator” (IPEx) which will be a technology demonstration of excavating and transporting 10 metric tons of lunar regolith on the surface of the moon with a 30kg-class robotic excavator. IPEx will be the next generation of robotic excavators to use bucket drums as excavation tools. This is an evolution of the Regolith Advanced Surface Systems Operations Robot (RASSOR) developed at NASA’s Kennedy Space Center (KSC). Bucket drums are hollow cylinders with regularly spaced scoops around the perimeter. The drums rotate in one direction to collect regolith with the scoops. The regolith slides down an internal baffling system inside the drum which prevents the regolith from falling back out of the scoops (see Figure 1). The captured regolith can then be transported while held in the drum and then deposited by rotating the drum in the opposite direction allowing the regolith to slide back down the baffling and out of the excavation scoops. Bucket drums were developed by Lockheed Martin in 2008 and used on multiple robotic excavator prototypes ever since. However, the forces on a bucket drum and considerations for scaling have not been measured in detail. Bucket drums are challenging to model using classical blade\bucket equations because of their unique geometry. Therefore, this experiment was performed to measure the forces on three bucket drums of the same geometry at different scales. Small: 9.4” (239mm) dia. x 8.1” (206mm) width, Medium: 11.6” (294mm) dia. x 10” (254mm) width, and Large: 17” (432mm) dia. x 14.1” (358mm) width. The test stand consisted of an actuated gantry with controlled motion in the vertical (Z) and horizontal (X) axes and a single rotation axis (R). The bucket drums were individually mounted to the rotary axis of the test stand and translated across a prepared bed of BP-1 lunar regolith simulant at a specified linear speed and cutting depth. The test stand was outfitted with a torque sensor in line with the rotation of the drum (R) and a 3 axis (X, Y, and Z) load cell. In addition to the three sizes of bucket drums the linear excavation speed and cutting depth were test variables. The results of these experiments show the relationship between the three scales of bucket drums for factors such as: excavation force, torque due to regolith rotation inside the drum, excavation energy, time to fill, etc. and will be discussed in detail in this paper. This fundamental data will be used in the design of IPEx and can inform the design of future bucket drum excavators.

RASSOR↗

NASA NTRS2022

Trajectory Generation for Flexible-Joint Space Manipulators

Space manipulator arms often exhibit significant joint flexibility and limited motor torque. Future space missions, including satellite servicing and large structure assembly, may involve the manipulation of massive objects, which will accentuate these limitations. Currently, astronauts use visual feedback on-orbit to mitigate oscillations and trajectory following issues. Large time delays between orbit and Earth make ground teleoperation difficult in these conditions, so more autonomous operations must be considered to remove the astronaut resource requirement and expand robotic capabilities in space. Trajectory planning for autonomous systems must therefore be considered to prevent poor trajectory tracking performance. We provide a model-based trajectory generation methodology that incorporates constraints on joint speed, motor torque, and base actuation for flexible-joint space manipulators while minimizing total trajectory time. Full spatial computer simulation results, as well as physical experiment results with a single-joint robot on an air bearing table, show the efficacy of our methodology.

Space robotics↗

NASA NTRSDate not supplied

Modeling Spacesuit-Human Interaction for Injury Risk Identification

Performing functional tasks while inside of the space suit introduces additional ergonomic challenges which can lead to musculoskeletal stresses and injuries in astronauts. Computational modeling of the suit-body interaction can be used alongside human-in-the-loop testing to understand and mitigate these risks and potentially improve the work performance. In this work, a static rigid-body model of the human body was integrated with the space suit and the process is described. This model enables prediction of the resulting joint torques and musculoskeletal loading from a simulated extravehicular activity (EVA) task. For representative EVA tasks, joint torque and body angles were used as parameters to predict the muscle strength required to achieve the task, as well as the percentage of the general and astronaut-like population that could achieve that strength demand. Population strength capability can be used as an indicator of the difficulty of a task and the level of injury risk for the given task types and crew anthropometry. The sensitivity of the model to inputs such as body joint location within the space suit and individual anthropometry will also be evaluated. Future work will use a database of3D human body scans and the movements of the body inside the suit during different EVA tasks to identify potential soft tissue contact points. The specific locations and magnitudes of contacts between the body and suit are expected to identify risk of repetitive tissue contact stresses. Overall, this model will provide a new tool to structurally identify the injury risks of EVA tasks and evaluate alternate strategies to reduce injury risk.

Garima Gupta↗

NASA NTRS2021

Kinetically Tunable, Active Auxetic, and Variable Recruitment Active Textiles from Hierarchical Assemblies

Multifunctional textiles with programmable, multi-axial, distributed, and scalable actuation are highly desirable and presently unrealized. 1D torque-unbalanced active yarns within 2D textile structures are exploited to produce soft and scalable active textiles that exhibit tunable displacements, forces, stiffnesses, and kinematic deformations. Through a textile hierarchy spanning active material composition, yarn construction, textile geometry, and system architecture, these active textiles accomplish kinetic tunability, variable recruitment behaviors, and auxetic effects without mechanical contact, called active auxetic effects. New modes of pre-programmed multi-axial performance are enabled by geometrically manipulating—specifically pre-stressing and constraining—active filaments in torsion and leveraging their structural elastic instability within a textile geometry. The new kinematic motion afforded by torque-unbalanced active yarns enhances the performance of active textiles, which accomplish tensile strokes over 40%, generated blocked forces up to 308 N m−1, and specific work over 0.4. kJ kg−1. Advances in active textiles are demonstrated through multifunctional 3D applications, including a variable constriction pump that exhibits sequential actuation, a wearable that conforms multi-axially around the body, and a soft exoskeleton that performs assistive motions and on-body anchoring simultaneously. By harnessing the capabilities of active materials within a textile hierarchy, advances in the potentiality of multifunctional textiles are presented.

Active auxetic effects↗

NASA NTRSDate not supplied

Cryobotics: Extreme Cold Environment Testing

The extreme cold environment test chamber was designed to conduct research in cryobotics; an area of study that focuses on robotic systems and rotating machinery operating in extreme cold environments including Earth, low Earth orbit, Mars, Moon, asteroids, Solar orbit, planetary orbit, or those encountered during travel among these destinations. The test chamber incorporates a modular dynamometer, consisting of a variety of brakes, torque sensors and motors to be easily interchanged between tests. Each test employs a unique test profile that incorporates different setpoints of applied torques and velocities for a given period or number of revolutions. The modularity of the dynamometer setup allows for any combination of motor, gearbox to be tested. The chamber has been used to run tests for various projects including Bulk Metallic Glass Gears (BMGG), Volatiles Investigating Polar Exploration Rover (VIPER), Intelligent Payload Experiment (IPEX), and Pilot Excavator. Various upgrades have been made to the extreme cold environment test chamber for the use of cryobotic research. These upgrades greatly increased the autonomous capabilities of the test set up by providing redundancies in the hardware and software. The redundancies were primarily added to protect the integrity of the cryohead. A new strapping and insulation method was performed to create the thermal conductive path from the actuators to the cryohead. The software was upgraded to include temperature setpoint control, further increasing the autonomous capabilities of the test. This paper goes into detail regarding the upgrades made to the extreme cold environment test chamber, as well as highlights the results from a COLDArm acceptance test.

Jonathan Drew Smith↗

NASA NTRS2023

Modeling and Simulation of the Angel Upper Limb Offload Device: Branching Into New Methods

BACKGROUND: The Active Response Gravity Offload System (ARGOS) provides an analog environment for extravehicular activity (EVA) testing and training. Discomfort has been observed during longer suited test sessions. While the subject’s core is offloaded during surface EVA evaluations, his/her arms experience full Earth gravity and can become overly fatigued, especially during suited tests which involve reaching and prolonged arm extensions. A device (ARGOS Negation of Gravitational Effects on the Limbs: ANGEL) to offload the weight of the arms and suit sleeves is being developed by JSC’s Flight Systems Branch of the Software, Robotics, and Simulation Division. Previously we have shared preliminary modeling of that device and kinematics based on motion capture data. Here we present an alternative approach to determine device kinematics by calculating ANGEL component angles with an OpenSim plugin. We compare calculated angles to inverse kinematics (IK) derived ones with the goal of validating the model. This new method can be further informative for device design and analytically testing different configurations to achieve desired reduced gravity conditions (e.g., lunar gravity (Lg) or Martian gravity (Mg)). We have compared calculated angles with IK-derived angles in tests with a shirt-sleeve subject positioned in a test stand with a Mark-III Hard Upper Torso (HUT) and Portable Life Support System (PLSS) mockup and arm weights to emulate the weight of the suit sleeve as well as a suited subject in ARGOS with a Mark-III suit. A variety of upper body tasks were completed in the former and full-body tasks in the latter. METHODS AND RESULTS: To model the offload device, we augment the OpenSim human model topology with the offload mechanism components and joints, using CAD models to represent the mechanism graphically. The joint angles of the device are calculated in the OpenSim plugin by modeling how the components configure themselves under the offloading spring tension given a particular IK-derived arm position. There are four ANGEL components with a total of 5 degrees of freedom (DOFs), each component has a single DOF except for the cuff which is modeled as 2 DOFs. The sickle/yaw bracket and cuff rotation angles are determined statically based on the assumptions that the sickle will track the attachment point of the cuff and that the cuff will rotate such that the attachment point is at its highest point. The cuff tilt, linker and V-bracket angles are then determined by optimizing their positions to approach a mechanical equilibrium. The calculated linker angle is compared to three different methods of determining the linker line-of-force kinematically (from V-bracket to center-cuff, cuff highest point or marker-derived position). Given the joint angles of the device, the spring force and resulting force on the arm is computed by the plugin and applied as an external load in inverse dynamics (ID) to enable study of overall shoulder joint torques as well as offload achieved. We verify the calculated joint angles by using the inverse kinematic data. The average difference in angles is the smallest for the V-bracket and linker, around 1 to 5 degrees for most trials. The resulting offload and shoulder torque are comparable between calculated and IK-derived angles. In summary, we have developed a method to calculate the joint angles of an exoskeleton-like upper limb offloading device currently in development. We have also developed a custom plugin which will be a valuable tool to optimize device configurations for a desired gravitational environment, probe the offload achieved for motions recorded outside of our test suite, and inform future design improvements.

L B Nilsson↗

NASA NTRSDate not supplied

A Machine Learning Model for Solar Sail Shape Reconstruction Using Flight Data

Solar sail deformation leads to disturbance torques from solar radiation pressure, driving performance requirements for momentum management systems. For the Solar Cruiser technology demonstrator mission, we have developed a model leveraging neural network-based machine learning to derive sail shape characteristics. The model uses torque and attitude telemetry simulated from a reduced-order tensor model of the deformed sail mesh over a characterization sequence. The machine learning model predicts sail boom deflection with comparable accuracy to that of an onboard context camera. This model can discover sail shape with no additional mass or data downlink requirements, allowing for validation of sail force modeling assumptions using in flight data. The results from the project hold promise for the further implementation of machine learning techniques in solar sail telemetry analysis and control.

solar sail↗

NASA NTRSDate not supplied

A Machine Learning Model for Solar Sail Shape Reconstruction Using Flight Data

Solar sail deformation leads to disturbance torques from solar radiation pressure, driving performance requirements for momentum management systems. For the Solar Cruiser technology demonstrator mission, we have developed a model leveraging neural network-based machine learning to derive sail shape characteristics. The model uses torque and attitude telemetry simulated from a reduced-order tensor model of the deformed sail mesh over a characterization sequence. The machine learning model predicts sail boom deflection with comparable accuracy to that of an onboard context camera. This model can discover sail shape with no additional mass or data downlink requirements, allowing for validation of sail force modeling assumptions using in flight data. The results from the project hold promise for the further implementation of machine learning techniques in solar sail telemetry analysis and control.

solar sail↗

NASA NTRS2023

Modeling and Simulation of The Angel Upper Limb Offload Device: Branching into New Methods

BACKGROUND: The Active Response Gravity Offload System (ARGOS) provides an analog environment for extravehicular activity (EVA) testing and training. Discomfort has been observed during longer suited test sessions. While the subject’s core is offloaded during surface EVA evaluations, his/her arms experience full Earth gravity and can become overly fatigued, especially during suited tests which involve reaching and prolonged arm extensions. A device (ARGOS Negation of Gravitational Effects on the Limbs: ANGEL) to offload the weight of the arms and suit sleeves is being developed by JSC’s Flight Systems Branch of the Software, Robotics, and Simulation Division. Previously we have shared preliminary modeling of that device and kinematics based on motion capture data. Here we present an alternative approach to determine device kinematics by calculating ANGEL component angles with an OpenSim plugin. We compare calculated angles to inverse kinematics (IK) derived ones with the goal of validating the model. This new method can be further informative for device design and analytically testing different configurations to achieve desired reduced gravity conditions (e.g., lunar gravity (Lg) or Martian gravity (Mg)). We have compared calculated angles with IK-derived angles in tests with a shirt-sleeve subject positioned in a test stand with a Mark-III Hard Upper Torso (HUT) and Portable Life Support System (PLSS) mockup and arm weights to emulate the weight of the suit sleeve as well as a suited subject in ARGOS with a Mark-III suit. A variety of upper body tasks were completed in the former and full-body tasks in the latter. METHODS AND RESULTS: To model the offload device, we augment the OpenSim human model topology with the offload mechanism components and joints, using CAD models to represent the mechanism graphically. The joint angles of the device are calculated in the OpenSim plugin by modeling how the components configure themselves under the offloading spring tension given a particular IK-derived arm position. There are four ANGEL components with a total of 5 degrees of freedom (DOFs), each component has a single DOF except for the cuff which is modeled as 2 DOFs. The sickle/yaw bracket and cuff rotation angles are determined statically based on the assumptions that the sickle will track the attachment point of the cuff and that the cuff will rotate such that the attachment point is at its highest point. The cuff tilt, linker and V-bracket angles are then determined by optimizing their positions to approach a mechanical equilibrium. The calculated linker angle is compared to three different methods of determining the linker line-of-force kinematically (from V-bracket to center-cuff, cuff highest point or marker-derived position). Given the joint angles of the device, the spring force and resulting force on the arm is computed by the plugin and applied as an external load in inverse dynamics (ID) to enable study of overall shoulder joint torques as well as offload achieved. We verify the calculated joint angles by using the inverse kinematic data. The average difference in angles is the smallest for the V-bracket and linker, around 1 to 5 degrees for most trials. The resulting offload and shoulder torque are comparable between calculated and IK-derived angles. In summary, we have developed a method to calculate the joint angles of an exoskeleton-like upper limb offloading device currently in development. We have also developed a custom plugin which will be a valuable tool to optimize device configurations for a desired gravitational environment, probe the offload achieved for motions recorded outside of our test suite, and inform future design improvements.

L B Nilsson↗

NASA NTRSDate not supplied

Implementation of Field-Oriented Control in Joint Actuator Electronics for Satellite-Servicing Robotics

NASA’s OSAM-1 (On-orbit Servicing, Assembly, and Manufacturing 1) is a robotic spacecraft designed to extend the life of a satellite. Launching in 2026, the OSAM-1 servicer will use a robotic arm to grasp, refuel, and relocate Landsat 7. In order to accomplish the various servicing operations, including the critical auto-grapple capturing operation, the robot arm uses active compliance and visual servo control loops. These sophisticated control algorithms are enabled by the high performance Joint Control Boards (JCBs). At the core of the robot arm control architecture, the JCBs employ field-oriented control (FOC) to accurately commutate and efficiently control joint actuator torque. FOC offers numerous benefits over other current control methods, allowing the JCBs to achieve the high bandwidth and performance required by the outer control loops. As an added benefit, a torque feed-forward term allows the FOC loop to simulate microgravity actuator performance during ground testing. In this paper, a FOC implementation for space robotics applications and an end-to-end actuator calibration process are discussed.

Sam Zhao↗

NASA NTRS2022

Remote Sensing of Coronal Forces During a Solar Prominence Eruption

We present a new methodology—the Keplerian Optical Dynamics Analysis (KODA)—for quantifying the dynamics of erupting magnetic structures in the solar corona. The technique involves adaptive spatiotemporal tracking of propagating intensity gradients and their characterization in terms of time-evolving Keplerian areas swept out by the position vectors of moving plasma blobs. Whereas gravity induces purely ballistic motions consistent with Kepler's second law, noncentral forces such as the Lorentz force introduce nonzero torques resulting in more complex motions. KODA algorithms enable direct evaluation of the line-of-sight component of the net torque density from the image-plane projection of the areal acceleration. The method is applied to the prominence eruption of 2011 June 7, observed by the Solar Dynamics Observatory's Atmospheric Imaging Assembly. Results obtained include quantitative estimates of the magnetic forces, field intensities, and blob masses and energies across a vast region impacted by the postreconnection redistribution of the prominence material. The magnetic pressure and energy are strongly dominant during the early, rising phase of the eruption, while the dynamic pressure and kinetic energy become significant contributors during the subsequent falling phases. Measured intensive properties of the prominence blobs are consistent with those of typical active-region prominences; measured extensive properties are compared with those of the whole pre-eruption prominence and the post-eruption coronal mass ejection of 2011 June 7, all derived by other investigators and techniques. We show that KODA provides valuable information on spatially and temporally dependent characteristics of coronal eruptions that is not readily available via alternative means, thereby shedding new light on the environment and evolution of these solar events.

V M Uritskiy↗