Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Effects of oxide surface chemistry on diffusioosmosis

Diffusioosmosis is the movement of fluid induced by gradients in solute concentration. Recent studies suggest that in low permeability rocks, it may be the dominant mode of reactant transport and thus control rates of diagenesis, which cannot be adequately explained by pressure-driven flow alone. In this paper we investigate how the equilibrium between an oxide mineral and the surrounding fluid phase influences the diffusioosmotic velocity. We have developed a theory for the case of a thin double layer, where the Debye length is smaller than the characteristic pore size. Several factors contribute to the total fluid velocity: the chemical structure of the mineral surface, the electrolyte type and concentration gradient, and the solution pH. Individual factors can act in concert or in opposition, leading to widely varying magnitudes and directions of the velocity. The numerical results are within the range of the limited experimental data. Our results highlight how surface charging and surface complexation impact the flow, and how they depend on pH.

Diagenesis↗

The effect of the surface composition of Ru-Pt bimetallic catalysts for methanol oxidation

Here, a series of Ru-Pt bimetallic catalysts prepared by the electroless deposition of controlled and variable amounts of Ru on the Pt surface of a commercially-available 20 wt% Pt/C catalyst has been characterized and evaluated for the oxidation of methanol. The activity of each Ru-Pt catalyst was determined as a function of surface composition via cyclic voltammetry. For the Ru-Pt bimetallic catalysts, activity passed through a maximum at approximately 50% monodisperse Ru surface coverage. However, due to the monolayer coverage of Ru on Pt, the amount of metal in the catalyst is minimized compared to a bulk 1:1 atomic ratio of Ru:Pt seen in commercial bimetallic catalysts. Chemisorption and temperature programmed reduction experiments confirmed that the surface had characteristics of a true bimetallic catalyst. On a mass of Pt basis, the activity of this composition for methanol oxidation was 7 times higher than pure Pt and 3.5 times higher than a commercial catalyst with a 1:1 Pt:Ru bulk atomic ratio.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Understanding photocatalytic overall water splitting on CoO nanoparticles: Effects of facets, surface stoichiometry, and the CoO/water interface

Unlike CoO micropowder, which is unable to split water, CoO nanoparticles have been observed to photocatalytically split water into H 2 and O 2 at room temperature without an externally applied potential or co-catalyst. The photocatalytic activity of CoO nanoparticles has been suggested to stem from an upwards shift in the band edges relative to bulk CoO such that the conduction and valence band edges span the water redox potentials. However, the origin of this shift in the band edges is unknown. In this study, we use first-principles density functional theory (DFT) calculations to explore the thermodynamically stable surface configurations of CoO as a function of oxygen chemical potential. Here we show that the band edge positions are sensitive to surface chemistry which is determined by surface orientation, adsorbates, and stoichiometry, and thus growth conditions and operating environment. In particular, we predict that CoO nanoparticles have fully hydroxylated CoO(1 1 1) facets, with band edges spanning the water redox potentials, while larger CoO particles (such as CoO micropowders) have a full monolayer of hydrogen on the CoO(1 1 1) facets, with a band alignment that favors water oxidation but not water reduction. Furthermore, we demonstrate that explicit inclusion of liquid water is crucial for accurately predicting the band edge positions, and thus photocatalytic behavior, of CoO in an aqueous solution. Our work explains why photocatalytic overall water splitting has only been observed on CoO nanoparticles, and provides new insights into the relationships between environmental conditions, surface structure, and band alignment, which may lead to new approaches for optimizing activity in CoO and other oxide photocatalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of free surfaces on localized plastic deformation in single-crystal nickel containing helium bubbles and radiation-induced self-interstitial atom clusters

This paper presents molecular dynamics (MD) simulations of plastic deformation in single-crystal Ni models containing internal distributions of helium (He) bubbles and self-interstitial atom (SIA) clusters corresponding to experimental characterization of ex-service Inconel X-750 components. Here, we simulate single crystals with and without free surfaces at room temperature and 588K, the latter temperature corresponding to the Inconel X-750 service conditions. Both models are deformed under multiple slip to a maximum deviatoric strain of ~10 %. A dislocation slip band forms in the model without free surfaces, but not in the model with free surfaces. However, the latter exhibits nano-twin nucleation from surfaces. Helium (He) bubbles that overlap with a slip band or a nano-twinned region deform more severely than other bubbles in the model. Nevertheless, the bubbles do not link up and do not form configurations that resemble incipient cracks.

36 MATERIALS SCIENCE↗

Optical properties of bimetallic Au-Cu nanocrystals embedded in glass

Highlights: • Bimetallic Au-Cu/Au-Cu sosoloid nanocrystals embedded in glass have been synthesized. • We achieved good size control of the nanocrystals. • The glasses with bimetallic nanoparticles exhibit enhanced for NLO. • The mechanisms on the nonlinear effects of the obtained glasses are discussed. - Abstract: Bimetallic gold-copper and gold-copper solid solutions nanocrystals (NCs) with orthorhombic morphologies were successfully embedded in sodium borosilicate glass; these materials were fabricated via a facile and synthetic sol-gel technique. Microstructural investigations demonstrate that the Au-Cu intermetallic nanostructure is generated in the glass host. Z-scan technique was applied to reveal the third-order nonlinear optical properties of the as-obtained glasses at the wavelength of 800 nm. The as-synthesized glasses exhibit similar nonlinear behaviors with reverse saturation absorption effects and self-focusing performances. The third-order nonlinear susceptibility χ{sup (3)} values were optimized by tuning the sizes of the Au-Cu NCs. The χ{sup (3)} of Au-Cu(1), Au-Cu(2) and Au-Cu(3) measured to be 3.1 × 10{sup −12}, 5.4 × 10{sup −12}, and 4.4 × 10{sup −12} esu for the single-pulse energy of 1 μJ. We have discussed the nonlinear optical mechanism of Au-Cu sodium borosilicate glass that may be due to the quantum confinement effects and surface plasmon resonance effects.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Effect of Fermi surface topology change on the Kagome superconductor CeRu 2 under pressure

The cubic Laves phase compound CeRu 2 with a Kagome substructure of Ru has been investigated to understand myriad fascinating phenomena resulting from competition among its various physical and geometric features. Such phenomena include flat bands, van Hove singularities, Dirac cones, reentrant superconductivity, magnetism, the Fulde–Ferrell–Larkin–Ovchinnikov state, valence fluctuations, time-irreversible anisotropic s-state superconductivity, etc. Extensive studies have thus been carried out since 1958 when the highly unusual coexistence of superconductivity and ferromagnetism was proposed for the mixed compounds (Ce,Gd)Ru 2 . Activity has accelerated in recent years due to increasing interest in topological states in superconductors. However, there has been little investigation of the mutual influence of these fascinating states. Therefore, we systematically investigated the superconductivity and possible Fermi surface topological change in CeRu 2 via magnetic, resistivity, and structural measurements under pressure up to ~168 GPa. An unusual phase diagram that suggests an intriguing interplay between the compound’s superconducting order and Fermi surface topological order has been constructed. A resurgence in its superconducting transition temperature was observed above 28 GPa. Our experiments have identified a structural transition above 76 GPa and a few tantalizing phase transitions driven by high pressure. Our high-pressure results further suggest that superconductivity and Fermi surface topology in CeRu 2 are strongly intertwined.

36 MATERIALS SCIENCE↗

Nuclear reactor radiation and temperature effects on piezoelectric surface acoustic wave devices

Surface acoustic wave (SAW) resonators were characterized in-situ in a nuclear reactor environment at high temperature. Devices based on lithium niobate (LiNbO 3 ), aluminum nitride (sc-AlN), and thin-film aluminum nitride on sapphire substrate (AlN/sapphire) were tested up to 400 °C temperature and 1.9 × 10 12 n/cm 2 s neutron flux. Shifts in device resonant frequency were detected in response to temperature and neutron flux. Devices undergo a frequency change when exposed to neutron flux. At 300 °C, AlN/sapphire produced the strongest neutron flux response about 1.02 ppm at 1.27 × 10 12 n/cm 2 s neutron flux (5.7 × 10 4 rad-Si/hr neutron dose rate), compared to 0.30 ppm for LiNbO 3 and 0.17 ppm for sc-AlN. While the transient kinetics in response to step change in neutron flux support the defect-accumulation mechanism, the concurrent measurement of device temperature using resistive temperature sensor suggests additional heating caused by absorption of gamma rays can also play a role. These results make SAW devices attractive candidates for sensor applications in extreme environments.

Aluminum nitride↗

Soiling of building envelope surfaces and its effect on solar reflectance. Part I: Analysis of roofing product databases

The use of highly reflective “cool” roofing materials can decrease demand for air conditioning, mitigate the urban heat island effect, and potentially slow global warming. However, initially high roof solar reflectance can be degraded by natural soiling and weathering processes. We evaluated solar reflectance losses after three years of natural exposure reported in two separate databases: the Rated Products Directory of the US Cool Roof Rating Council (CRRC) and information reported by manufacturers to the US Environmental Protection Agency (EPA)’s ENERGY STAR® rating program. Many product ratings were culled because they were duplicative (within a database) or not measured. A second, site-resolved version of the CRRC dataset was created by transcribing from paper records the site-specific measurements of aged solar reflectance in Florida, Arizona and Ohio. Products with high initial solar reflectance tended to lose reflectance, while those with very low initial solar reflectance tended to become more reflective as they aged. Within the site-resolved CRRC database, absolute solar reflectance losses for samples of medium-to-high initial solar reflectance were 2 - 3 times greater in Florida (hot and humid) than in Arizona (hot and dry); losses in Ohio (temperate but polluted) were intermediate. Disaggregating results by product type, factory-applied coating, field-applied coating, metal, modified bitumen, shingle, singleply membrane and tile, revealed that absolute solar reflectance losses were largest for fieldapplied coating, modified bitumen and single-ply membrane products, and smallest for factoryapplied coating and metal products.The 2008 Title 24 provisional aged solar reflectance formula overpredicts the measured aged solar reflectance of 0% to 30% of each product type in the culled public CRRC database. The rate of overprediction was greatest for field-applied coating and single-ply membrane products and least for factory-applied coating, shingle, and metal products. New product-specific formulas can be used to estimate provisional aged solar reflectance from initial solar reflectance pending measurement of aged solar reflectance. The appropriate value of soiling resistance varies by product type and is selected to attain some desired overprediction rate for the formula. The correlations for shingle products presented in this paper should not be used to predict aged solar reflectance or estimate provisional aged solar reflectance because the data set is too small and too limited in range of initial solar reflectance.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Soiling of building envelope surfaces and its effect on solar reflectance – Part II: Development of an accelerated aging method for roofing materials

Highly reflective roofs can decrease the energy required for building air conditioning, help mitigate the urban heat island effect, and slow global warming. However, these benefits are diminished by soiling and weathering processes that reduce the solar reflectance of most roofing materials. Soiling results from the deposition of atmospheric particulate matter and the growth of microorganisms, each of which absorb sunlight. Weathering of materials occurs with exposure to water, sunlight, and high temperatures. This study developed an accelerated aging method that incorporates features of soiling and weathering. The method sprays a calibrated aqueous soiling mixture of dust minerals, black carbon, humic acid, and salts onto preconditioned coupons of roofing materials, then subjects the soiled coupons to cycles of ultraviolet radiation, heat and water in a commercial weatherometer. Three soiling mixtures were optimized to reproduce the site-specific solar spectral reflectance features of roofing products exposed for 3 years in a hot and humid climate (Miami, Florida); a hot and dry climate (Phoenix, Arizona); and a polluted atmosphere in a temperate climate (Cleveland, Ohio). A fourth mixture was designed to reproduce the three-site average values of solar reflectance and thermal emittance attained after 3 years of natural exposure, which the Cool Roof Rating Council (CRRC) uses to rate roofing products sold in the US. This accelerated aging method was applied to 25 products₋single ply membranes, factory and field applied coatings, tiles, modified bitumen cap sheets, and asphalt shingles₋and reproduced in 3 days the CRRC's 3-year aged values of solar reflectance. In conclusion, this accelerated aging method can be used to speed the evaluation and rating of new cool roofing materials.

54 ENVIRONMENTAL SCIENCES↗