Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “performance model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Super Boiler 2 nd Generation Technology for Watertube Boilers

This report describes Phase I of a proposed two phase project to develop and demonstrate an advanced industrial watertube boiler system with the capability of reaching 94% (HHV) fuel-to-steam efficiency and emissions below 2 ppmv NO x , 2 ppmv CO, and 1 ppmv VOC on natural gas fuel. The boiler design would have the capability to produce >1500°F, >1500 psig superheated steam, burn multiple fuels, and will be 50% smaller/lighter than currently available watertube boilers of similar capacity. This project is built upon the successful Super Boiler project at GTI. In that project that employed a unique two-staged intercooled combustion system and an innovative heat recovery system to reduce NO x to below 5 ppmv and demonstrated fuel-to-steam efficiency of 94% (HHV). This project was carried out under the leadership of GTI with project partners Cleaver-Brooks, Inc., Nebraska Boiler, a Division of Cleaver-Brooks, and Media and Process Technology Inc., and project advisors Georgia Institute of Technology, Alstom Power Inc., Pacific Northwest National Laboratory and Oak Ridge National Laboratory. Phase I of efforts focused on developing 2 nd generation boiler concepts and performance modeling; incorporating multi-fuel (natural gas and oil) capabilities; assessing heat recovery, heat transfer and steam superheating approaches; and developing the overall conceptual engineering boiler design. Based on our analysis, the 2 nd generation Industrial Watertube Boiler when developed and commercialized, could potentially save 265 trillion Btu and $1.6 billion in fuel costs across U.S. industry through increased efficiency. Its ultra-clean combustion could eliminate 57,000 tons of NO x , 460,000 tons of CO, and 8.8 million tons of CO 2 annually from the atmosphere. Reduction in boiler size will bring cost-effective package boilers into a size range previously dominated by more expensive field-erected boilers, benefiting manufacturers and end users through lower capital costs.

03 NATURAL GAS↗

Replicating HCCI-like autoignition behavior: What gasoline surrogate fidelity is needed?

This work seeks to characterize the fidelity needed in a gasoline surrogate with the intent to replicate the complex autoignition behavior exhibited within advanced combustion engines, and specifically Homogeneous Charge Compression Ignition (HCCI). A low-temperature gasoline combustion (LGTC) engine operating in HCCI mode and a rapid compression machine (RCM) are utilized to experimentally quantify fuel reactivity, through autoignition and preliminary heat release characteristics. Fuels considered include a research grade E10 U.S. gasoline (RD5-87), three multi-component surrogates (PACE-1, PACE-8, PACE-20), and a binary surrogate (PRF88.4). Each fuel was studied at lean/HCCI-like conditions covering a wide range of temperatures and pressures that are representative of naturally aspirated to high boost engine operation. Detailed chemical kinetic modeling is also undertaken using a recently updated gasoline surrogate kinetic model to simulate the RCM experiments and to provide chemical insight into surrogate-to-surrogate differences. The LGTC engine experiments demonstrate nearly identical reactivity between PACE-20 and RD5-87 across studied conditions, while faster phasing is seen for both PACE-1 and PACE-8 due to their stronger intermediate- and low-temperature heat release (ITHR/LTHR) at naturally aspirated and boosted conditions, respectively. The RCM experiments reveal typical low-temperature, negative temperature coefficient (NTC) and intermediate-temperature autoignition behaviors at all pressure conditions for RD5-87, which are qualitatively reproduced by all surrogates. Quantitative discrepancies in both autoignition and preliminary heat release are observed for all surrogates, while their ability to replicate RD5-87 autoignition behavior follows the order of PACE-20 > PACE-1 > PACE-8 > PRF88.4. Excellent mapping is obtained between the LGTC engine and the RCM, where the engine pressure-time trajectories can be characterized by the regimes represented by the RCM autoignition isopleths. The kinetic model performs commendably when simulating both autoignition and preliminary heat release of PACE-20, while typically overpredicting ignition delay times for PACE-1, PACE-8 and PRF88.4 at high-pressure and low-temperature/NTC conditions. Sensitivity and rate of production (ROP) analyses highlight surrogate-to-surrogate differences in the governing chemical kinetics where n-pentane initiates rapid OH branching at a faster rate and an earlier timing for PACE-20 than iso-pentane does for PACE-1 and PACE-8, making it computationally more reactive than the other surrogates. The current study highlights the need to include non-standardized properties, such as the lean/HCCI-like autoignition characteristics, in addition to ASTM properties (e.g., RON, MON) as metrics of fuel reactivity and targets to be matched when formulating high-fidelity surrogates that fully capture gasoline advanced combustion behavior such as HCCI-like autoignition.

42 ENGINEERING↗

TREAT Transient Test Reactor Restart Status

Transient testing involves placing nuclear fuel or material into the core of a nuclear reactor designed to operate at high power for a short time, and subjecting the nuclear fuel or material to short bursts of intense, high power radiation. After the experiment is completed, the fuel or material is analyzed to determine the effects of the radiation. The results are then used in fuel or material design and/or qualification. Transient testing is required for essentially all nuclear fuel design and qualification efforts to learn how nuclear fuel will respond during accidents involving transient overpower and/or under cooling events. For example, nuclear fuel may fragment when exposed to higher than normal power. This fragmentation can cause unacceptable performance. Transient testing is also needed to validate performance models for nuclear fuel and materials. These models, when validated, will dramatically shorten the development and qualification life cycle for nuclear fuels, supporting rapid development of low emissions, reliable power generation. In the past, transient testing was primarily done in facilities that no longer exist. The U.S. Department of Energy evaluated how to provide the required transient testing capability and, following completion of the National Environmental Policy Act process, they selected the Transient Reactor Test (TREAT) facility to resume transient testing. TREAT is located at Idaho National Laboratory (INL). The TREAT reactor was used from 1959 to 1994 to conduct more than 2,500 nuclear fuel transient tests, and was placed in standby in 1994. TREAT is capable of transients in excess of 19 GW. The paper describes the progress towards restart. The restart efforts have revealed that the plant fuel and equipment is acceptable for future operations. The safety basis development, procedures, and training are well under way. Experiment capability preparations are in progress. Reactor startup is anticipated no later than 2018. (author)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Sentiment analysis of the United States public support of nuclear power on social media using large language models

This study utilized large language models (LLMs) to analyze public sentiment in the United States (US) regarding nuclear power on social media, focusing on X/Twitter, considering climate change challenges and advancements in nuclear power technology. Approximately, 1.26 million nuclear tweets from 2008–2023 were examined to fine-tune LLMs for sentiment classification. We found the crucial role of accurate data labeling for model performance, with potential implications for a 15% improvement, achieved through high-confidence labels. LLMs demonstrated better performance compared to traditional machine learning classifiers, with reduced susceptibility to overfitting and up to 96% classification accuracy. LLMs are used to segment the US public tweets into policy and energy-related categories, revealing that 68% are politically themed. Policy tweets tended to convey negative sentiment, often reflecting opposing political perspectives and focusing on nuclear deals and international relations. Energy-related tweets covered diverse topics with predominantly neutral to positive sentiment, indicating broad support for nuclear power in 48 out of 50 US states. The US public positive sentiments toward nuclear power stemmed from its high power density, reliability regardless of weather conditions, environmental benefits, application versatility, and recent innovations and advancements in both fission and fusion technologies. Negative sentiments primarily focused on waste management, high capital costs, and safety concerns. The neutral campaign highlighted global nuclear facts and advancements, with varying tones leaning towards positivity or negativity. An interesting neutral theme was the advocacy for the combined use of renewable and nuclear energy to attain net-zero goals.

Energy & Fuels↗

Performance Assessment Transport Modeling of Uranium at the Area 5 Radioactive Waste Management Site at the Nevada National Security Site

Following is a brief summary of the assumptions that are pertinent to the radioactive isotope transport in the GoldSim Performance Assessment model of the Area 5 Radioactive Waste Management Site, with special emphasis on the water-phase reactive transport of uranium, which includes depleted uranium products.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Evaluation of CMIP5 continental precipitation simulations relative to satellite-based gauge-adjusted observations

Numerous studies have emphasized that climate simulations are subject to various biases and uncertainties. The objective of this study is to cross-validate 34 Coupled Model Intercomparison Project Phase 5 (CMIP5) historical simulations of precipitation against the Global Precipitation Climatology Project (GPCP) data, quantifying model pattern discrepancies and biases for both entire data distributions and their upper tails. The results of the Volumetric Hit Index (VHI) analysis of the total monthly precipitation amounts show that most CMIP5 simulations are in good agreement with GPCP patterns in many areas, but that their replication of observed precipitation over arid regions and certain sub-continental regions (e.g., northern Eurasia, eastern Russia, central Australia) is problematical. Overall, the VHI of the multi-model ensemble mean and median also are superior to that of the individual CMIP5 models. However, at high quantiles of reference data (e.g., the 75th and 90th percentiles), all climate models display low skill in simulating precipitation, except over North America, the Amazon, and central Africa. Analyses of total bias (B) in CMIP5 simulations reveal that most models overestimate precipitation over regions of complex topography (e.g. western North and South America and southern Africa and Asia), while underestimating it over arid regions. Also, while most climate model simulations show low biases over Europe, inter-model variations in bias over Australia and Amazonia are considerable. The Quantile Bias (QB) analyses indicate that CMIP5 simulations are even more biased at high quantiles of precipitation. Lastly, we found that a simple mean-field bias removal improves the overall B and VHI values, but does not make a significant improvement in these model performance metrics at high quantiles of precipitation.

54 ENVIRONMENTAL SCIENCES↗

Optimizing 3d spin polarization of CoOOH by in situ Mo doping for efficient oxygen evolution reaction

Transition-metal oxyhydroxides are attractive catalysts for oxygen evolution reactions (OERs). Further studies for developing transition-metal oxyhydroxide catalysts and understanding their catalytic mechanisms will benefit their quick transition to the next catalysts. Herein, Mo-doped CoOOH was designed as a high-performance model electrocatalyst with durability for 20 h at 10 mA cm -2 . Additionally, it had an overpotential of 260 mV (glassy carbon) or 215 mV (nickel foam), which was 78 mV lower than that of IrO 2 (338 mV). In situ, Raman spectroscopy revealed the transformation process of CoOOH. Calculations using the density functional theory showed that during OER, doped Mo increased the spin-up density of states and shrank the spin-down bandgap of the 3d orbits in the reconstructed CoOOH under the electrochemical activation process, which simultaneously optimized the adsorption and electron conduction of oxygen-related intermediates on Co sites and lowered the OER overpotentials. Our research provides new insights into the methodical planning of the creation of transition-metal oxyhydroxide OER catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Soil water percolation and nutrient fluxes as a function of topographical, seasonal and soil texture variation in Central Amazonia, Brazil

Abstract Understanding soil water dynamics and transport of nutrients is challenging in tropical rainforests due to the uniqueness of several properties related to soils, vegetation and seasonality that make relating patterns found in temperate environments to tropical sites difficult. We address the need for better edaphic characterization in tropical environments by investigating soil water percolation rates and chemistry across topographic, soil texture and seasonal gradients in a mature tropical rainforest in Central Amazonia, Brazil. We utilized a passive wick flux meter (e.g., drainage lysimeter) to directly measure real‐time percolation fluxes at 60‐cm depth, and to sample a suite of chemical species across plateau, slope and valley topographic positions. We found percolation flux volume and chemical exports generally increase with decreasing elevation and clay content, which was lowest in the valley. Daily percolation flux was observed to be 2.39 ± 0.44 in plateau, 3.01 ± 0.50 in slope and 6.16 ± 0.83 mm in valley. Most solutes were present in small amounts of <1 mg L −1 , such as PO₄ 3− , Fe 2+ /Fe 3+ and Mn 2+ ; however, NO 3 − concentrations were >20 mg L −1 , even exceeding 100 mg L −1 in the valley. Based on additional isotopic analysis, we speculate high NO 3 − concentrations are partially an artefact of root decomposition following installation of the flux meters. The empirical relationships we show among percolation volume and nutrient exports under varying topographies and soil textures can improve Earth System Model performance by better constraining ecohydrological relationships to nutrient fluxes, which can in‐turn better illuminate the important factors that govern their behaviour.

54 ENVIRONMENTAL SCIENCES↗

The Phenix‐AlphaFold webservice: Enabling AlphaFold predictions for use in Phenix

Abstract Advances in machine learning have enabled sufficiently accurate predictions of protein structure to be used in macromolecular structure determination with crystallography and cryo‐electron microscopy data. The Phenix software suite has AlphaFold predictions integrated into an automated pipeline that can start with an amino acid sequence and data, and automatically perform model‐building and refinement to return a protein model fitted into the data. Due to the steep technical requirements of running AlphaFold efficiently, we have implemented a Phenix‐AlphaFold webservice that enables all Phenix users to run AlphaFold predictions remotely from the Phenix GUI starting with the official 1.21 release. This webservice will be improved based on how it is used by the research community and the future research directions for Phenix.

Poon, Billy K.↗

Modeling absorption spectra of molecules in solution

The presence of solvent tunes many properties of a molecule, such as its ground and excited state geometry, dipole moment, excitation energy, and absorption spectrum. Because the energy of the system will vary depending on the solvent configuration, explicit solute–solvent interactions are key to understanding solution-phase reactivity and spectroscopy, simulating accurate inhomogeneous broadening, and predicting absorption spectra. In this tutorial review, we give an overview of factors to consider when modeling excited states of molecules interacting with explicit solvent. We provide practical guidelines for sampling solute–solvent configurations, choosing a solvent model, performing the excited state electronic structure calculations, and computing spectral lineshapes. Furthermore, we introduce our recent results combining the vertical excitation energies computed from an ensemble of solute–solvent configurations with the vibronic spectra obtained from a small number of frozen solvent configurations, resulting in improved simulation of absorption spectra for molecules in solution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Many-Core Acceleration of a Discrete Ordinates Transport Mini-App at Extreme Scale, In: ISC High Performance 2016: High Performance Computing

Time-dependent deterministic discrete ordinates transport codes are an important class of application which provide significant challenges for large, many-core systems. One such challenge is the large memory capacity needed by the solve step, which requires us to have a scalable solution in order to have enough node-level memory to store all the data. In our previous work, we demonstrated the first implementation which showed a significant performance benefit for single node solves using GPUs. In this paper we extend our work to large problems and demonstrate the scalability of our solution on two Petascale GPU-based supercomputers: Titan at Oak Ridge and Piz Daint at CSCS. Our results show that our improved node-level parallelism scheme scales just as well across large systems as previous approaches when using the tried and tested KBA domain decomposition technique. We validate our results against an improved performance model which predicts the runtime of the main ‘sweep’ routine when running on different hardware, including CPUs or GPUs.

Computer Science↗

Interpreting LHC SUSY searches in the phenomenological MSSM

We interpret within the phenomenological MSSM (pMSSM) the results of SUSY searches published by the CMS collaboration based on the first ~1 fb^-1 of data taken during the 2011 LHC run at 7 TeV. The pMSSM is a 19-dimensional parametrization of the MSSM that captures most of its phenomenological features. It encompasses, and goes beyond, a broad range of more constrained SUSY models. Performing a global Bayesian analysis, we obtain posterior probability densities of parameters, masses and derived observables. In contrast to constraints derived for particular SUSY breaking schemes, such as the CMSSM, our results provide more generic conclusions on how the current data constrain the MSSM.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Modelling and computational improvements to the simulation of single vector-boson plus jet processes for the ATLAS experiment

This paper presents updated Monte Carlo configurations used to model the production of single electroweak vector bosons (W, Z/γ$^{∗}$) in association with jets in proton-proton collisions for the ATLAS experiment at the Large Hadron Collider. Improvements pertaining to the electroweak input scheme, parton-shower splitting kernels and scale-setting scheme are shown for multi-jet merged configurations accurate to next-to-leading order in the strong and electroweak couplings. The computational resources required for these set-ups are assessed, and approximations are introduced resulting in a factor three reduction of the per-event CPU time without affecting the physics modelling performance. Continuous statistical enhancement techniques are introduced by ATLAS in order to populate low cross-section regions of phase space and are shown to match or exceed the generated effective luminosity. This, together with the lower per-event CPU time, results in a 50% reduction in the required computing resources compared to a legacy set-up previously used by the ATLAS collaboration. The set-ups described in this paper will be used for future ATLAS analyses and lay the foundation for the next generation of Monte Carlo predictions for single vector-boson plus jets production.[graphic not available: see fulltext]

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Multigrid methods with space–time concurrency

Here, we consider the comparison of multigrid methods for parabolic partial differential equations that allow space–time concurrency. With current trends in computer architectures leading towards systems with more, but not faster, processors, space–time concurrency is crucial for speeding up time-integration simulations. In contrast, traditional time-integration techniques impose serious limitations on parallel performance due to the sequential nature of the time-stepping approach, allowing spatial concurrency only. This paper considers the three basic options of multigrid algorithms on space–time grids that allow parallelism in space and time: coarsening in space and time, semicoarsening in the spatial dimensions, and semicoarsening in the temporal dimension. We develop parallel software and performance models to study the three methods at scales of up to 16K cores and introduce an extension of one of them for handling multistep time integration. We then discuss advantages and disadvantages of the different approaches and their benefit compared to traditional space-parallel algorithms with sequential time stepping on modern architectures.

97 MATHEMATICS AND COMPUTING↗

Evaluation of Radioactive Aerosol Precipitation on the Inner Surfaces of Steam-Water Lines in Beyond Design Basis Accidents at NPP with RBMK

The results of modeling performed with the MELCOR code of the transport and precipitation of fission product aerosols in the steam-water lines of RBMK during beyond design basis accidents are presented. It is shown that the precipitation of fission product aerosols on the inner surfaces of steam-water lines depends on the course of the accident and can be an effective mechanism for lowering their atmospheric emissions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Simulation of carbon cycling, including dissolved organic carbon transport, in forest soil locally enriched with 14C

The DyDOC model was used to simulate organic matter decomposition and dissolved organic matter (DOM) transport in deciduous forest soils at the Oak Ridge Reservation (ORR) in Tennessee, USA. The model application relied on extensive data from the Enriched Background Isotope study (EBIS), which made use of a local atmospheric enrichment of radiocarbon to establish a large-scale manipulation experiment with different inputs of 14C from both above-ground and below-ground litter. The aim of the modelling was to test if the processes that constitute DyDOC can explain the available observations for C dynamics in the ORR. More specifically we used the model to investigate the origins of DOM, its dynamics within the soil profile, and how it contributes to the formation of stable carbon in the mineral soil. The model was first configured to account for water transport through the soil, then observed pools and fluxes of carbon and 14C data were used to fit the model parameters that describe the rates of the metabolic transformations. The soils were described by a thin O-horizon, a 15 cm thick A-horizon and a 45-cm thick B-horizon. Within the thin O-horizon, litter is either converted to CO2 or to a second organic matter pool, which is converted to CO2 at a different rate, both pools being able to produce DOM. The best model performance was obtained by assuming that adsorption of downwardly transported DOM in horizons A and B, followed by further conversion to stable forms, produces mineral-associated carbon pools, while root litter is the source of non-mineral associated carbon, with relatively short residence times. In the simulated steady-state, most carbon entering the O-horizon leaves quickly as CO2, but 17% (46 gC m-2 a-1) is lost as DOC in percolating water. The DOM comprises mainly hydrophobic material, 40% being derived from litter and 60% from older organic matter pools (residence time ~ 10 years). Most of the DOM is converted to CO2 in the mineral soil, over timescales of 1 to 15 years, but there is a conversion of 11 gC m-2 a-1 into stabilised forms that turnover on a timescale of 100-200 years. The small flux of DOC leaving the B-horizon (1.2 gC m-2 a-1) is mainly hydrophilic material, some of which can penetrate to depth quickly after formation. Considering the soil profile as single entity, the simulated soil carbon pools at ORR have mean residence times in the range 1-200 years, most of the carbon being in the slow pools, most of the turnover associated with the faster ones.

54 ENVIRONMENTAL SCIENCES↗

Improved MPI collectives for MPI processes in shared address spaces

As the number of cores per node keeps increasing, it becomes increasingly important for MPI to leverage shared memory for intranode communication. This paper investigates the design and optimization of MPI collectives for clusters of NUMA nodes. We develop performance models for collective communication using shared memory and we demonstrate several algorithms for various collectives. Experiments are conducted on both Xeon X5650 and Opteron 6100 InfiniBand clusters. The measurements agree with the model and indicate that different algorithms dominate for short vectors and long vectors. We compare our shared-memory allreduce with several MPI implementations-Open MPI, MPICH2, and MVAPICH2-that utilize system shared memory to facilitate interprocess communication. On a 16-node Xeon cluster and 8-node Opteron cluster, our implementation achieves on geometric average 2.3X and 2.1X speedup over the best MPI implementation, respectively. Our techniques enable an efficient implementation of collective operations on future multi- and manycore systems.

Collective communication↗

Large-scale optimization-based non-negative computational framework for diffusion equations: Parallel implementation and performance studies

It is well-known that the standard Galerkin formulation, which is often the formulation of choice under the finite element method for solving self-adjoint diffusion equations, does not meet maximum principles and the non-negative constraint for anisotropic diffusion equations. Recently, optimization-based methodologies that satisfy maximum principles and the non-negative constraint for steady-state and transient diffusion-type equations have been proposed. To date, these methodologies have been tested only on small-scale academic problems. The purpose of this paper is to systematically study the performance of the non-negative methodology in the context of high performance computing (HPC). PETSc and TAO libraries are, respectively, used for the parallel environment and optimization solvers. For large-scale problems, it is important for computational scientists to understand the computational performance of current algorithms available in these scientific libraries. The numerical experiments are conducted on the state-of-the-art HPC systems, and a single-core performance model is used to better characterize the efficiency of the solvers. Furthermore, our studies indicate that the proposed non-negative computational framework for diffusion-type equations exhibits excellent strong scaling for real-world large-scale problems.

97 MATHEMATICS AND COMPUTING↗