Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Microstructure and Mechanical Properties of Spray-Formed 7075 Alloy During Retrogression

The mechanical properties, conductivity, microstructure, precipitation behavior and evolution process of elements and phases of spray-formed 7075 alloy during retrogression are studied by the tensile test, electric test, hardness test, transmission electron microscope (TEM), x-ray diffraction (XRD) analysis, electron-dispersive spectroscopy (EDS) and lattice parameter measurements. The results show that the mechanical properties and conductivity of the alloy can be effectively improved when treated at a suitable retrogression temperature and time. According to the TEM observations, XRD analysis, EDS and an accurate measurement of the lattice parameter, the redissolution of elements and precipitated phases can be readily observed. From the optimization selection of the RRA treatment for the 7075 alloy, the regularity of redissolution and precipitation of the elements and phases are evaluated. The ultimate tensile strength, yield strength, hardness, elongation and conductivity of the spray-formed 7075 alloy after preaging at 120 °C for 16 h, retrogression at 200 °C for 8 min and reaging at 120 °C for 24 h are 791, 736 MPa, 181 HBW, 8.5% and 22.6 MS/m, respectively.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure and Electromagnetic Shielding Properties of Mg-Zn-Ce-Y-Zr Alloys

Microstructure and electromagnetic interference shielding properties of extruded Mg-Zn-Ce-Y-Zr alloys were systematically investigated. A bimodal grain structure of fine recrystallized grains and deformed grains was observed in the alloys. Yttrium (Y) and cerium (Ce) refined the recrystallized grains. Mg-Zn-Ce phase, Mg{sub 3}Zn{sub 3}Y{sub 2} phase and a few precipitates containing Zn and Zr were observed. Y and Ce additions changed the texture of the alloys. When the total rare earth content reached 4 wt.%, the texture was remarkably weaker than other studied alloys. The shielding capacity increased first and then decreased with Y contents. The value of shielding effectiveness for the extruded Mg-5Zn-1Ce-2Y-0.6Zr alloys reached 79-118 dB in the frequency range of 30 MHz-1.5 GHz, which was significantly higher than that of some aluminum alloys. The addition of Y and Ce is effective in improving the shielding capacity in Mg alloys. The electrical conductivity and second phases in the alloys were important in enhancing shielding effectiveness. The texture and precipitation exerted significant effect on electrical conductivity. In addition, subsequently aging treatment evidently improved shielding effectiveness.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructural Evolution and Mechanical Behavior of Lead-Free Silicon Brass Manufactured by Low-Pressure Die Casting

Low-pressure die casting (LPDC) has been widely used to process aluminum and magnesium alloys; however, it has yet to be applied to manufacture brass alloys. This study investigates the microstructural evolution and mechanical behavior of a lead-free CuZnSiAl silicon brass via a variable-controlling approach on the basis of a faucet casting by LPDC. The manufactured silicon brass castings are predominantly composed of bcc β-CuZn(Si, Al) and minor fcc α-Cu(Zn, Si) solid solutions. The silicon brass castings also predominantly exhibit short rod-like or granular α phases, which distinctly differ from the acicular α morphology obtained by conventional gravity casting. The manufactured silicon brass castings which contain finer β grains and short rod-like or granular α phase exhibit superior mechanical properties. Their optimal mechanical properties—elongation of 15.0%, yield strength of 359.8 MPa, and ultimate tensile strength of 598.9 MPa—are far superior to those of the typical lead brass HPb59-1. The results obtained in this study provide insight into the manufacture and design of lead-free silicon brass castings by LDPC.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure and Deformation Mechanism of AZ31 Magnesium Alloy Under Dynamic Strain Rate

A hot-rolled AZ31Mg alloy sheet was subjected to dynamic plastic deformation parallel to the rolling direction, and microstructural evolutions and mechanical properties of the deformed samples were examined. It has been found that dynamic strain rate could facilitate {10-12} twin nucleation and growth and leads to a lower yield stress of about 20 MPa and an early end to twinning characteristic (happening at a strain point of about 6%) shown in the stress–strain curve. {10-12} twinning mechanism dominates the early plastic deformation; but when plastic strain exceeds ~ 9%, dislocation–slip mechanism instead of {10-12} twinning dominates the later plastic deformation. And this premature transformation of the dominant deformation mechanisms from {10-12} twinning to dislocation slip is caused by dynamic strain rate. The effect of dynamic strain rate on the number of twin nucleations remains unclear, and the more systematic researches are needed in the future.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure, Texture, and Mechanical Properties of Ni-W Alloy After Accumulative Roll Bonding

In this study, the microstructure, texture, and mechanical properties evolution of Ni-14W (wt.%) alloy processed up to four cycles of accumulative roll-bonding (ARB) were investigated using electron backscatter diffraction, microhardness measurements, and tensile tests. The initial equiaxed grains, with an average size of 10 μm, underwent a strong refinement after ARB processing. The elongated ultrafine grains were parallel to the rolling direction, with a grain thickness of 0.2 µm. The texture after ARB processing was characterized by the typical rolling components (Copper, S and Brass), which showed a tendency toward stabilization after four cycles. The microhardness increased substantially (+ 86%) and seemed to saturate after three cycles. The tensile tests demonstrated that Ni-14W samples subjected to ARB processing exhibited high strength (> 1200 MPa after three ARB cycles) and very poor ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effects of Rotation Speed on Microstructure and Mechanical Properties of 2060 Al-Cu-Li Alloy in Friction Stir Welding

Microstructural and mechanical properties of 2.0-mm-thick 2060 Al-Cu-Li alloy joints obtained at different rotation speeds were assessed in this study. The rotation speeds ranged from 400 to 1300 rpm, with welding speed kept at a constant value of 100 mm/min. With the increase in rotation speed, grain coarsening occurred while the density of precipitation decreased in the stir zone (SZ), and great amounts of the Al{sub 2}CuLi and Al{sub 2}Cu phases were dissolved while only small amounts of the Al{sub 3}Zr and Al{sub 3}Li phases remained. The lowest hardness was found at the interface between the heat-affected zone (HAZ) and thermo-mechanically affected zone (TMAZ); the average hardness value of SZ increased, while the lowest hardness moved in the direction away from the center of joints. The ultimate strength (UTS) of weld first increased rapidly and then slowly decreased as rotation speed increased, with a maximum value of 443 MPa obtained at a rotation speed of 600 rpm, reaching 83.58% of the base metal (BM) strength. Three fracture modes were established to illustrate the growth mechanism of the crack. Analysis of the fracture surface showed that insufficient materials flowed and coarsened secondary phases caused the joint fracture.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Study on Microstructure and Properties of AZ31/6061 GTAW Butt Joints According to Mg-Cd-Al Ternary System

AZ31 Mg and 6061 Al were successfully joined by GTAW method with Cd as filler metal. The tensile strength of the joints reached 170 MPa through this alloying method according to Mg-Cd-Al ternary system. The microstructure, phases, element distribution and fracture mechanism of alloyed joints were studied. The results suggest that the fusion zone is mainly composed of CdMg compounds and Al-based solid solution. A transitional zone thickness of 40-80 μm with few primary Al{sub 12}Mg{sub 17} and fine Al{sub 12}Mg{sub 17}-MCMS (MCMS represents a mixture of CdMg and CdMg{sub 3} compounds) eutectic is formed between the AZ31 base metal and fusion zone. The fracture surface presents three distinct regions because of the different distribution of Al{sub 12}Mg{sub 17} compounds in the transitional zone. The alloying with Cd filler metal can disperse Al{sub 12}Mg{sub 17} intermetallic compounds and form CdMg ordered compounds with excellent plasticity. Thus, the mechanical properties of alloyed joints have been significantly enhanced.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructure and Performance of Nano-WC Particle-Strengthened Ni Coatings by Electro-brush Plating

Nano-WC particle-strengthened Ni composite coatings were prepared by electro-brush plating. A series of artificial neural network models was developed for the analysis and prediction of the coating performance. The microstructure and phase structure were studied with SEM, XRD and EDS. Nano-WC particles as the hard phase were distributed evenly and dispersed in the coatings, which was conducive to the hardness enhancement of the coatings. Additionally, nano-WC particles as microballs inserted in the coatings could reduce the friction when wear of the coating surface occurred. Furthermore, the addition of nano-WC particles delayed the time of crack initiation and propagation in the coatings, which increased the service lifetime when they worked in a thermal shock environment.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2018

Microstructure and Mechanical Properties of Cast Al-5Zn-2Mg Alloy Subjected to Equal-Channel Angular Pressing

In the present work, cast Al-5Zn-2Mg alloy was processed through equal-channel angular pressing (ECAP) in route B{sub C} up to four number of passes. Microstructure and mechanical properties were investigated on processed and unprocessed materials. In cast condition, the material was composed of dendritic structure. After homogenization treatment, large-sized grains were observed. After ECAP processing, significant grain refinement was observed. After ECAP processing, high-density dislocations and high degree of misorientation between the grains were observed. In cast material, rod-shaped precipitates were observed, while, after ECAP processing, spherical-shaped precipitates were observed. ECAP processing leads to a noticeable improvement in the mechanical properties of the material. After four passes, 122% improvement in the microhardness and 135% improvement in the ultimate tensile strength of the material were observed. After three passes, a slight decrease in the mechanical properties was observed. This is attributed to the dissolution of the metastable η′ phase, annihilation of dislocations, dynamic recrystallization and texturing during ECAP processing. Brittle fracture mode was observed in tensile testing cast and homogenized samples. After ECAP processing, fracture mode was changed into shear fracture mode.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Microstructural Characterization and Electrochemical Behavior of AA2014 Al-Cu-Mg-Si Alloy of Various Tempers

AA2014 Al-Cu-Mg-Si alloy is subjected to aging heat treatment, and microstructural features and electrochemical behavior of the AA2014 Al-Cu-Mg-Si alloy of various tempers have been characterized. Hardness measurement of the alloy of different tempers showed typical age hardening behavior. X-ray diffraction and transmission electron microscopy studies revealed the presence of characteristic phases. Differential scanning calorimetry study displayed the sequence of solid-state precipitation and dissolution reactions in the AA2014 alloy of various tempers. Electrochemical behavior was assessed by measurement of variation of open-circuit voltage with time, potentiodynamic polarization and potentiodynamic cyclic polarization of the AA2014 alloy of various tempers in 3.5 wt.% NaCl solution at near neural (pH ~ 7) and at alkaline (pH 12) conditions. Potentiodynamic polarization studies of different tempers in 3.5 wt.% NaCl solution at pH ~ 7 showed that the corrosion potential (E{sub corr}) value has shifted toward more negative (active) direction with increasing aging time. The cyclic polarization in 3.5 wt.% NaCl solution at pH ~ 7 displayed active–passive behavior and also showed a large hysteresis loop indicating high pit growth damage.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Effect of Zinc Interlayer in Microstructure Evolution and Mechanical Properties in Dissimilar Friction Stir Welding of Aluminum to Titanium

The welding of aluminum (Al) and titanium (Ti) is difficult and challenging due to the differences in their chemical and physical properties, and the formation of brittle intermetallic phases. In the present experiment, a zinc (Zn) interlayer was used during friction stir welding of Al to Ti. The weld was characterized in detail to understand the mechanisms associated with microstructural evolution and improvement in mechanical properties of the weld. X-ray computed tomography results reveal three-dimensional distribution of particles and flakes of titanium in the weld nugget. It was also observed that Ti particles are inhomogeneously distributed in the weld and the distribution depends on their morphology. Such a distribution of Ti was informative in understanding material flow. In addition, the consolidation of Zn in the Al matrix reveals the nature of material flow in the weld nugget as well. The importance of the Zn interlayer and mechanism of phase formation was explored in this study. It was characterized that the mechanical mixing of Zn with Al and Ti alters phase evolution and restricts the formation of conventional Al{sub 3}Ti intermetallic phase. The presence of zinc homogenizes elemental distribution and inhibits the formation of brittle intermetallic phases, which leads to a substantial improvement in mechanical properties of the weld.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure, Phase Transformation, Mechanical Behavior, Bio-corrosion and Antibacterial Properties of Ti-Nb-xSn (x = 0, 0.25, 0.5 and 1.5) SMAs

Porous Ti-Nb-xSn shape memory alloys (SMAs) are fabricated by microwave sintering technology. The microstructures exhibit needle-like morphologies, β{sub (N)} (normal straight and crossed needles along with needle-like morphology that resembles spaghetti or irregular lines with α-phases in between) as well as plate-like morphologies [normal straight plate-like morphology, α′′ and dendritic plate-like morphology, β{sub (D)}]. Increases in Sn addition significantly induce an increase in the density of the α-phase. XRD patterns exhibited three phases, namely the β-main phase with smaller intensities of α′′ and α. Further, the addition of 0.25% Sn led to more effective improvement in the intensity of the α′′-phase compared with 0.5% and 1.5% Sn addition. Additions of Sn also enhanced the fracture strength and its corresponding strain along with the shape memory effect (SME), where the best enhancement was achieved at 0.25% Sn. The corrosion rate (Ri) was reduced by rising Sn content, while both corrosion resistance and antibacterial zones were increased. The lower elastic modulus, as well as the robust mechanical properties and bioactivity, made these SMAs rather suitable for biomedical application purposes, where the low elastic modulus had value in terms of avoiding the problem of “stress shielding.”.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Fabrication, Analysis of Microstructure and Oxidation Resistance of Cemented C/C Composites by Laser

Cylindrical carbon–carbon composites have been cemented using a CO{sub 2} laser actuated by a raster scanning mirror system in a four-step sequence. Complete and homogenous surface cementation as well as thermal stability of the composites was sought after and achieved. The line of heat created from the laser beam impinged parallel to the axis of the pre-coated cylinder, while suspended from one end and slowly rotated. Four slurry compositions, all containing chloride salts from refractory elements, some combined with silicon, were pre-deposited by air spraying it over each specimen and then laser treated sequentially. Confined heat sublimed the chlorine ions resulting in silicide compounds that reacted with the carbon substrate to form a bonding layer. Microstructure characterization was performed using scanning electron microscopy, energy-dispersive spectroscopy and x-ray diffraction, immediately after the cementation was consolidated and after heat treated under argon. Preliminary oxidation weight loss tests were performed up to 1423 K under argon and air, revealing a 9.8 and 30.6% weight reduction, respectively, after 9 h of exposure. Cemented specimens were then coated with a glass overcoat layer that allowed them to perform moderately better against oxidation achieving up to a 28% weight loss after 20 h at 1273 K in air.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Cold Deformation and Heat Treatment on the Microstructure and Mechanical Behavior of High Entropy Alloy CuCrFeNi{sub 2}Al{sub 0.5}

CuCrFeNi{sub 2}Al{sub 0.5}, a high entropy alloy (HEA) with a single FCC phase, was deformed at room temperature and then heat treated. The small particles precipitated from the deformed FCC solid solution matrix after heating at 700 °C, softening the solid solution matrix. This outcome confirms that the microstructure of HEAs can be controlled by heat treatment in addition to controlling the chemical composition and the rate of cooling from liquid alloys. The hardness of the samples increased due to precipitation hardening, and the specimen heated at 700 °C with 10% predeformation had the highest hardness. As the predeformation increases, the precipitates tend to interweave in the network morphology. Meanwhile, grains in all specimens became more severely coarse after heat treatment at 1100 °C. Predeformation followed by annealing can obviously slow down the creep rate, indicating that annealing at an appropriate temperature can improve the mechanical properties of deformed HEA.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure and Mechanical Properties of Powder Thixoforged Amorphous Ni{sub 55}Nb{sub 35}Si{sub 10}-Reinforced Al Matrix Composites

Powder thixoforging was used to produce amorphous Ni{sub 55}Nb{sub 35}Si{sub 10}-reinforced Al matrix composites from recycled Al powders obtained from ball-milled Al520 end-milled billets. The amorphous reinforcing material was uniformly dispersed in the Al matrix and bonded adequately with it without undesired interfacial reactions. The compressive yield strength of composites with 45% reinforcement content increased 248% to 794 MPa over as-cast samples. The maximum elongation and hardness of samples were 15%, and 60.4 HRA, respectively. The relative density of the unreinforced thixoforged sample was 99.8%, indicating near-perfect compaction of Al powders. The maximum elongation, hardness, and compressive yield strength of thixoforged monolithic matrix alloys were, respectively, 40%, 56.9 HRA, and 747 MPa (a 228% increase in CYS over the cast alloy). In contrast, cold-forged samples showed only 82% increase in compressive yield strength over the as-cast alloy. Powder thixoforging introduced in this study—even without reinforcement—delivers better mechanical properties compared to cold forging most likely due to the refinement and modification of the microstructure during powder ball milling.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Microstructure and Corrosion Properties of Laser-Welded SAF 2507 Super Duplex Stainless Steel Joints

SAF 2507 super duplex stainless steel has been welded using laser beam (LB) welding and laser/gas metal arc hybrid (LGH) welding processes. The pitting and intergranular corrosion properties of the welding joints have been tested using electrochemical testing and microstructure observations. The volume fraction of the ferrite phase reaches 70% in the weld zone of the LB welding joint, while the volume fraction of the ferrite phase is 60% for the welding joint of LGH due to the introduction of Ni from welding wire. The pitting corrosion resistance of the welding joint for LB is better than that of LGH. The pitting corrosion is easily conceived in the heat-affected zone (HAZ) because of the formation of Cr{sub 2}N in the HAZ during welding.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effects of Thermal Exposure on the Microstructure and Mechanical Properties of Al-Si-Cu-Ni-Mg-Gd Alloy

The present study focused on the effect of thermal exposure on the phase evolution and properties of the cast-T6 Al-12Si-4Cu-2Ni-0.8Mg-xGd (x = 0, 0.1, and 0.2) alloy used for cast piston.The thermal stability of the alloys was studied in the temperature range of 200-300 °C for exposure duration up to 500 h, thus obtaining the relationship between the microstructural evolution and its impact on the mechanical properties. The fine Al{sub 2}Cu phase grew into the coarse θ-Al{sub 2}Cu phases during the thermal exposure, resulting in a decrease in the mechanical strength of the alloy. The thermal stability and stiffness of the Al-Si-Cu-Ni-Mg alloys were improved with the increase in Gd content from 0 to 0.2%.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Improvement of Microstructure and Mechanical Properties of CoCrCuFeNi High-Entropy Alloys By V Addition

V element had positive effect in improving the strength of many alloys, so it was possible that V had potential to strengthen CoCrCuFeNi high-entropy alloys (HEAs) with face-centered cubic (FCC) crystal structure, which was relatively weak in strength and had outstanding ductility. In this paper, we studied the alloying effect of V on the phase evolution, microstructure and the mechanical properties of the (CoCrCuFeNi){sub 100−x}V{sub x} (x = 0-16, atomic ratio, hereafter in at.%) HEAs systematically. The results showed that V element had capacity to induce sigma phase precipitation. The volume fraction of sigma phase increased from 0 to 12%; the compressive yield stress of (CoCrCuFeNi){sub 100−x}V{sub x} HEAs increased from 300 to 613 MPa with V content increasing from 0 to 16% (atomic ratio, hereafter in at.%). However, the compression fracture strain decreased from 50 to 28%. V addition was beneficial in improving the strength of CoCrCuFeNi HEA, and the increase in sigma phase volume fraction was the key factor for the improvement of the (CoCrCuFeNi){sub 100−x}V{sub x} HEAs in yield stress.

36 MATERIALS SCIENCE↗