Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “layers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

An experimental study of a reattaching supersonic shear layer

A Mach 1.83 fully developed turbulent boundary layer was separated at a 25.4 mm backward step and formed a free shear layer. The incoming boundary layer thickness, momentum thickness, and Reynolds number were approximately 8 mm, 0.5 mm, and 52x10 to the 6th/m, respectively. A two-component coincident LDV system was used to take velocity measurements of the incoming boundary layer, the free shear layer, and the reattached shear layer. The results confirmed the existence of organized structures in both the free and the reattached shear layer which was reported earlier based on the authors dynamic pressure measurements and Schlieren photographs.

Samimy, M.↗
NASA NTRS1989

Double-peaked sodium layers at high latitudes

Na lidar observations indicate that at high latitudes in summer the neutral Na layer frequently attains a double-peaked structure. The main layer with a maximum near 90 km altitude is supplemented by a secondary, narrow layer near 95 km altitude. Results are presented concerning secondary sodium layers. It appears likely that the formation of secondary Na layers observed frequently above the lidar site is not solely a 'sodium phenomenon', but part of a more comprehensive layering process for metal atoms and ions. Na(+)/Na density ratios close to 0.5 near the peaks of both the main and secondary layers are derived.

Von Zahn, U.↗
NASA NTRS1990

Layered Internal-Photoemission Sensor

High quantum efficiency achieved without multiple layer contacts. Proposed infrared sensor based on photoemission from multiple layers of metal silicide sandwiched between layers of silicon. Suitable for use in focal-plane arrays. Layered internal-photoemission sensor has positive/intrinsic/negative structure modified by inclusion of layers or islands of metal silicide. Holes photo-excited from silicide regions and swept to detection by reverse-bias electric field in intrinsic silicon. Easier to make because internal layers allowed to "float" electrically, contact being made with only two outer semiconductor layers.

Fathauer, Robert W.↗
NASA NTRS1987

Boundary-layer receptivity and laminar-flow airfoil design

Boundary-layer receptivity examines the way in which external disturbances generate instability waves in boundary layers. Receptivity theory is complementary to stability theory, which studies the evolution of disturbances that are already present in the boundary layer. A transition prediction method which combines receptivity with linear stability theory would directly account for the influence of free-stream disturbances and also consider the characteristics of the boundary layer upstream of the neutral stability point. The current e sup N transition prediction methods require empirical correlations for the influence of environmental disturbances, and totally ignore the boundary layer characteristics upstream of the neutral stability point. The regions where boundary-layer receptivity occurs can be separated into two classes, one near the leading edges and the other at the downstream points where the boundary layer undergoes rapid streamwise adjustments. Analyses were developed for both types of regions, and parametric studies which examine the relative importance of different mechanisms were carried out. The work presented here has focused on the low Mach number case. Extensions to high subsonic and supersonic conditions are presently underway.

Kerschen, Edward J.↗
NASA NTRS1990

Method of forming a multiple layer dielectric and a hot film sensor therewith

The invention is a method of forming a multiple layer dielectric for use in a hot-film laminar separation sensor. The multiple layer dielectric substrate is formed by depositing a first layer of a thermoelastic polymer such as on an electrically conductive substrate such as the metal surface of a model to be tested under cryogenic conditions and high Reynolds numbers. Next, a second dielectric layer of fused silica is formed on the first dielectric layer of thermoplastic polymer. A resistive metal film is deposited on selected areas of the multiple layer dielectric substrate to form one or more hot-film sensor elements to which aluminum electrical circuits deposited upon the multiple layered dielectric substrate are connected.

Hopson, Purnell, Jr.↗
NASA NTRS1989

A layered abduction model of perception: Integrating bottom-up and top-down processing in a multi-sense agent

A layered-abduction model of perception is presented which unifies bottom-up and top-down processing in a single logical and information-processing framework. The process of interpreting the input from each sense is broken down into discrete layers of interpretation, where at each layer a best explanation hypothesis is formed of the data presented by the layer or layers below, with the help of information available laterally and from above. The formation of this hypothesis is treated as a problem of abductive inference, similar to diagnosis and theory formation. Thus this model brings a knowledge-based problem-solving approach to the analysis of perception, treating perception as a kind of compiled cognition. The bottom-up passing of information from layer to layer defines channels of information flow, which separate and converge in a specific way for any specific sense modality. Multi-modal perception occurs where channels converge from more than one sense. This model has not yet been implemented, though it is based on systems which have been successful in medical and mechanical diagnosis and medical test interpretation.

Josephson, John R.↗
NASA NTRS1989

Effect of velocity ratio on plane mixing layer development

An experimental study has been conducted to investigate the effect of velocity ratio on the development of a plane mixing layer to self-similarity. Plane mixing layers with five different velocity ratios (0.5, 0.6, 0.7, 0.8 and 0.9) were generated in a newly designed mixing layer wind tunnel with both initial boundary layers tripped. For each velocity ratio, mean flow and turbulence measurements were obtained at eight streamwise locations with a single cross-wire probe. The results indicate that the splittter plate wake plays a very dominant and, in some cases, a lasting role in the development of the mixing layer. For velocity ratios between 0.5 and 0.7, self-similarity of the mixing layer was observed with the asymptotic states comparable. Mixing layers with the higher velocity ratios failed to achieve a self-similar state within the measurement domain. The development distance decreased with increasing velocity ratio up to 0.7, after which it appeared to increase. Almost all of the observed effects may be attributed to the presence and subsequent behavior of the splitter plate wake.

Mehta, R. D.↗
NASA NTRS1991

User's manual for the Langley boundary layer noise propagation program (MRS-BLP)

A computer program, McAninch-Rawls-Spence Boundary Layer Propagation (MRS-BLP), is described. This program models the refractive and scattering effects on acoustic pressure waves propagating through a boundary layer encompassing an aircraft's fuselage. The noise source is assumed known and generated by a propeller. The fuselage is represented by an infinitely long cylinder embedded in a longitudinal flow. By matching a numerical solution inside the boundary layer with an analytical solution outside the boundary layer, the program calculates the acoustic pressure at the surface of the cylinder given the incident field at the top of the boundary layer. The boundary layer flow velocity and sound speed profiles, as well as the boundary layer thickness may be specified by the user. A detailed description of the input parameters and how to execute the program is given. Example executions of MRS-BLP showing results are also included.

Spence, Peter L.↗
NASA NTRS1992

Interface of an uncoupled boundary layer algorithm with an inviscid core flow algorithm for unsteady supersonic engine inlets

An uncoupled boundary layer algorithm was combined with an inviscid core flow algorithm to model flows within supersonic engine inlets. The inviscid flow algorithm that was used was the LArge Perturbation INlet Code (LAPIN). The boundary layer and inviscid core flow algorithms were formulated in different manners. The boundary layer algorithm was two dimensional and solved in nonconservation form, while the core flow algorithm was one dimensional and solved in conservation form. In order to interface the two codes, the following modifications were important. The coordinate system was set up to maintain the parabolic nature of the boundary layer algorithm while approaching the one dimensional core flow solution far from a wall. The pressure gradient used in the boundary layer equation was calculated using the core flow values and the boundary layer equations, so the boundary layer solution smoothly approached the core flow values far from the wall. Flaring was used for the advection terms perpendicular to the core flow to maintain the stability of the algorithm. With these modifications, the combined viscous/inviscid algorithm matched well with experimental observations of pressure distributions with a supersonic inlet.

Darling, Douglas↗
NASA NTRS1992

Effects of fiber and interfacial layer architectures on the thermoplastic response of metal matrix composites

Examined here is the effect of fiber and interfacial layer morphologies on thermal fields in metal matrix composites (MMCs). A micromechanics model based on an arbitrarily layered concentric cylinder configuration is used to calculate thermal stress fields in MMCs subjected to spatially uniform temperature changes. The fiber is modelled as a layered material with isotropic or orthotropic elastic layers, whereas the surrounding matrix, including interfacial layers, is treated as a strain-hardening, elastoplastic, von Mises solid with temperature-dependent parameters. The solution to the boundary-value problem of an arbitrarily layered concentric cylinder under the prescribed thermal loading is obtained using the local/global stiffness matrix formulation originally developed for stress analysis of multilayered elastic media. Examples are provided that illustrate how the morphology of the SCS6 silicon carbide fiber and the use of multiple compliant layers at the fiber/matrix interface affect the evolution of residual stresses in SiC/Ti composites during fabrication cool-down.

Pindera, Marek-Jerzy↗
NASA NTRS1992

The three-dimensional turbulent boundary layer near a plane of symmetry

The asymptotic structure of the three-dimensional turbulent boundary layer near a plane of symmetry is considered in the limit of large Reynolds number. A self-consistent two-layer structure is shown to exist wherein the streamwise velocity is brought to rest through an outer defect layer and an inner wall layer in a manner similar to that in two-dimensional boundary layers. The cross-stream velocity distribution is more complex and two terms in the asymptotic expansion are required to yield a complete profile which is shown to exhibit a logarithmic region. The flow in the inner wall layer is demonstrated to be collateral to leading order; pressure-gradient effects are formally of higher order but can cause the velocity profile to skew substantially near the wall at the large but finite Reynolds numbers encountered in practice. The governing set of ordinary differential equations describing a self-similar flow is derived. The calculated numerical solutions of these equations are matched asymptotically to an inner wall-layer solution and the results show trends that are consistent with experimental observations.

Degani, A. T.↗
NASA NTRS1992

Structure of a swirling turbulent mixing layer

A single-stream swirling turbulent mixing layer was produced in which the angular momentum instability acts over most of the layer for most of its development length. The instability is associated with a large increase in the level of the conventional Reynolds stresses over those in an unswirled mixing layer. This paper presents measurements of the three-dimensionality of the mean flow at one axial location well downstream of the origin. The output of a fixed hot-wire probe was ensemble-averaged to produce an approximation to the mean flow field that would be seen by a rotating observer. The main goals of this study were to establish the presence or absence of Taylor-Goertler vortices found in unstable laminar boundary layers. The variations in the mean velocities and Reynolds stresses are generally consistent with a bodily 'wrinkling' of the mixing layer, without a significant variation in the layer thickness. The wrinkling is most probably a result of circumferential variations in the initial boundary layer, which in turn originate at the swirl generator.

Wood, D. H.↗
NASA NTRS1992

Interface of an uncoupled boundary layer algorithm with an inviscid core flow algorithm for unsteady supersonic engine inlets

An uncoupled boundary layer algorithm was combined with an inviscid core flow algorithm to model flows within supersonic engine inlets. The inviscid flow algorithm that was used was the LArge Perturbation INlet Code (LAPIN). The boundary layer and inviscid core flow algorithms were formulated in different manners. The boundary layer algorithm was two dimensional and solved in nonconservation form, while the core flow algorithm was one dimensional and solved in conservation form. In order to interface the two codes, the following modifications were important. The coordinate system was set up to maintain the parabolic nature of the boundary layer algorithm while approaching the one dimensional core flow solution far from a wall. The pressure gradient used in the boundary layer equation was calculated using the core flow values and the boundary layer equations, so the boundary layer solution smoothly approached the core flow values far from the wall. Flaring was used for the advection terms perpendicular to the core flow to maintain the stability of the algorithm. With these modifications, the combined viscous/inviscid algorithm matched well experimental observations of pressure distributions with a supersonic inlet.

Darling, Douglas↗
NASA NTRS1934

On the theory of laminar boundary layers involving separation

This paper presents a mathematical discussion of the laminar boundary layer, which was developed with a view of facilitating the investigation of those boundary layers in particular for which the phenomenon of separation occurs. The treatment starts with a slight modification of the form of the boundary layer equation first published by Von Mises. Two approximate solutions of this equation are found, one of which is exact at the outer edge of the boundary layer while the other is exact at the wall. The final solution is obtained by joining these two solutions at the inflection points of the velocity profiles. The final solution is given in terms of a series of universal functions for a fairly broad class of potential velocity distributions outside of the boundary layer. Detailed calculations of the boundary layer characteristics are worked out for the case in which the potential velocity is a linear function of the distance from the upstream stagnation point. Finally, the complete separation point characteristics are determined for the boundary layer associated with a potential velocity distribution made up of two linear functions of the distance from the stagnation point. It appears that extensions of the detailed calculations to more complex potential flows can be fairly easily carried out by using the explicit formulae given in the paper. (author)

Von Karman, TH↗
NASA NTRS1993

Application of a Reynolds stress model to separating boundary layers

Separating turbulent boundary layers occur in many practical engineering applications. Nonetheless, the physics of separation/reattachment of flows is poorly understood. During the past decade, various turbulence models were proposed and their ability to successfully predict some types of flows was shown. However. prediction of separating/reattaching flows is still a formidable task for model developers. The present study is concerned with the process of separation from a smooth surface. Features of turbulent separating boundary layers that are relevant to modeling include the following: the occurrence of zero wall shear stress, which causes breakdown of the boundary layer approximation; the law of the wall not being satisfied in the mean back flow region; high turbulence levels in the separated region; a significant low-frequency motion in the separation bubble; and the turbulence structure of the separated shear layer being quite different from that of either the mixing layers or the boundary layers. These special characteristics of separating boundary layers make it difficult for simple turbulence models to correctly predict their behavior.

Ko, Sung HO↗
NASA NTRS1994

The Martian atmospheric planetary boundary layer stability, fluxes, spectra, and similarity

This is the first analysis of the high frequency data from the Viking lander and spectra of wind, in the Martian atmospheric surface layer, along with the diurnal variation of the height of the mixed surface layer, are calculated for the first time for Mars. Heat and momentum fluxes, stability, and z(sub O) are estimated for early spring, from a surface temperature model and from Viking Lander 2 temperatures and winds at 44 deg N, using Monin-Obukhov similarity theory. The afternoon maximum height of the mixed layer for these seasons and conditions is estimated to lie between 3.6 and 9.2 km. Estimations of this height is of primary importance to all models of the boundary layer and Martian General Circulation Models (GCM's). Model spectra for two measuring heights and three surface roughnesses are calculated using the depth of the mixed layer, and the surface layer parameters and flow distortion by the lander is also taken into account. These experiments indicate that z(sub O), probably lies between 1.0 and 3.0 cm, and most likely is closer to 1.0 cm. The spectra are adjusted to simulate aliasing and high frequency rolloff, the latter caused both by the sensor response and the large Kolmogorov length on Mars. Since the spectral models depend on the surface parameters, including the estimated surface temperature, their agreement with the calculated spectra indicates that the surface layer estimates are self consistent. This agreement is especially noteworthy in that the inertial subrange is virtually absent in the Martian atmosphere at this height, due to the large Kolmogorov length scale. These analyses extend the range of applicability of terrestrial results and demonstrate that it is possible to estimate the effects of severe aliasing of wind measurements, to produce a models which agree well with the measured spectra. The results show that similarity theory developed for Earth applies to Mars, and that the spectral models are universal.

Tillman, James E.↗
NASA NTRS1994

Roles of drizzle in a one-dimensional third-order turbulence closure model of the nocturnal stratus-topped marine boundary layer

This study focuses on the effects of drizzle in a one-dimensional third-order turbulence closure model of the nocturnal stratus-topped marine boundary layer. When the simulated drizzle rate is relatively small (maximum approximately equal to 0.6 mm/day), steady-state solutions are obtained. The boundary layer stabilizes essentially because drizzle causes evaporative cooling of the subcloud layer. This stabilization considerably reduces the buoyancy flux and turbulence kinetic energy below the stratus cloud. Thus, drizzle tends to decouple the cloud from the subcloud layer in the model, as suggested by many observational studies. In addition, the evaporation of drizzle in the subcloud layer creates small scattered clouds, which are likely to represent cumulus clouds, below the solid stratus cloud in the model. The sensitivity experiments show that these scattered clouds help maintain a coupled boundary layer. When the drizzle rate is relatively large (maximum approximately equal to 0.9 mm/day), the response of the model becomes transient with bursts in turbulent fluxes. This phenomenon is related to the formation of the scattered cloud layer below the solid stratus cloud. It appears that the model is inadequate to represent the heat and moisture transport by strong updrafts covering a small fractional area in cumulus convection.

Wang, Shouping↗
NASA NTRS1993

First in-situ observations of neutral and plasma density fluctuations within a PMSE layer

The NLC-91 rocket and radar campaign provided the first opportunity for high resolution neutral and plasma turbulence measurements with simultaneous observations of PMSE (Polar Mesospheric Summer Echoes). During the flight of the TURBO payload on August 1, 1991, Cornell University Portable Radar Interferometer (CUPRI) and European Incoherent Scattter facility (EISCAT) observed double PMSE layers located at 86 and 88 km altitude, respectively. Strong neutral density fluctuations were observed in the upper layer but not in the lower layer. The fluctuation spectra of the ions and neutrals within the upper layer are consistent with standard turbulence theories. However, we show that there is no neutral turbulence present in the lower layer and that something else must have been operating here to create the plasma fluctuations and hence the radar echoes. Although the in situ measurements of the electron density fluctuations are much stronger in the lower layer, the higher absolute electron density of the upper layer more than compensated for the weaker fluctuations yielding comparable radar echo powers.

Lubken, Franz-Josef↗