Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “experimentation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86
All sourcesNASA NTRSDOE OSTI
NASA NTRS1953

Comparison of the Experimental and Theoretical Distribution of Lift on a Slender Inclined Body of Revolution at M = 2

Pressure distributions and force characteristics have been determined for a body of revolution consisting of a fineness ratio 5.75, circular-arc, ogival nose tangent to a cylindrical afterbody for an angle-of-attack range of 0 degrees to 35.5 degrees. The free-stream Mach number was 1.98 and the free-stream Reynolds number was approximately 0.5 x 10 sup 6, based on body diameter. Comparison of the theoretical and experimental pressure distributions shows that for zero lift, either slender-body theory or higher-order theories yield results which are in good agreement with experiment. For the lifting case, good agreement with theory is found only for low angles of attack and for the region in which the body cross-sectional area is increasing in the downstream direction. Because of the effects of cross-flow separation and the effects of compressibility due to the high cross-flow Mach numbers at large angles of attack, the experimental pressure distributions differ from those predicted by potential theory. Although the flow about the inclined body was, in general, similar to that assumed as the basis for Allen's method of estimating the forces resulting from viscous effects (NACA RM A91I26), the distribution of the forces was significantly different from that assumed. Nevertheless, the lift and pitching-moment characteristics were in fair agreement with the estimated value.

Perkins, Edward W↗
NASA NTRS1952

Analytical and Experimental Investigation of Inlet-engine Matching for Turbojet-powered Aircraft at Mach Numbers up to 2.0

An analysis of inlet-turbojet-engine matching for a range of Mach numbers up to 2.0 indicates large performance penalties when fixed-geometry inlets are used. Use of variable-geometry inlets, however, nearly eliminates th The analysis was confirmed experimentally by investigating at Mach numbers of 0, 0.63, and 1.5 to 2.0 two single oblique-shock-type inlets of different compression-ramp angles, which simulated a variable-geometry configuration. The experimental investigation indicated that total-pressure recoveries comparable withose attainable with well designed nose inlets were obtained with the side inlets when all the boundary layer ahead of the inlets was removed. Serious drag penalties resulted at a Mach number of 2.0 from the use of blunt-cowl leading edges. However, sharp-lip inlets produced large losses in thrust for the take-off condition. These thrust penalties which are associated with the the low-speed operation of the sharp-lip inlet designs can probably be avoided without impairing the supersonic performance of the inlet by the use of auxiliary inlets or blow-in doors.

Esenwein, Fred T↗
NASA NTRS1954

Design and Test of Mixed-flow Impellers IV : Experimental Results for Impeller Models MFI-1 and MFI-2 with Changes in Blade Height

Modifications A and B of impeller model MFI-1 and A, B, and C of impeller model MFI-2 were investigated experimentally in an attempt to determine what allowance in blade height should be made for boundary layer and viscous losses in an impeller designed for isentropic compressible flow. A gradual increase in blade height was arbitrarily made from inlet to outlet in anticipation of a gradual build-up of boundary layer. Apparently there was a rapid build-up of boundary layer near the inlet in the experimental case rather than a gradual one. Therefore, the proper allowance for boundary layer cannot be described from the data obtained. Decreasing the pressure gradient along the shroud by reducing the blade height allowance apparently did little to increase the overall efficiency. At the design speed of 1400 feet per second, the overall adiabatic efficiency was increased from 0.83 for the MFI-1A to 0.85 for the MFI-1B with reduction in height; however, it is indicated from the theoretical velocity distribution and outlet surveys that the increase was due to a change from decelerating to accelerating flow along the hub rather than from any change along the shroud. It is further indicated that the consequences of a thickened or separated boundary layer depend not only on the design velocity gradients but also on the shape of the passage.

Hamrick, Joseph T↗
NASA NTRS1957

Comparison of experimental with theoretical total-pressure loss in parallel-walled turbojet combustors

An experimental investigation of combustor total-pressure loss was undertaken to confirm previous theoretical analyses of effects of geometric and flow variables and of heat addition. The results indicate that a reasonable estimate of cold-flow total-pressure-loss coefficient may be obtained from the theoretical analyses. Calculated total-pressure loss due to heat addition agreed with experimental data only when there was no flame ejection from the liner at the upstream air-entry holes.

Dittrich, Ralph T↗
NASA NTRS1929

Mathematical and experimental investigation of heat control and power increase in air-cooled aircraft engines

In order to understand the numerical relations between the air velocity, temperature of the cylinder walls, heat dissipation, cylinder dimensions and type of construction an experimental plant was installed in the Siemens and Halske laboratory. The experimental cylinder was exposed to the air stream of a wind tunnel. The compression chamber was heated by an electrically heated oil bath kept constantly in motion by a stirrer. The wall temperatures were measured by thermocouples. The air stream was produced a seven-watt blower. The air flowed through a current rectifier (honeycomb), diffuser, air chamber with quieting sieves and a nozzle.

ENGINES - AIR COOLED - POWER INCREASES↗
NASA NTRS1956

Review of experimental investigations of liquid-metal heat transfer

Experimental data of various investigators of liquid-metal heat-transfer characteristics were reevaluated using as consistent assumptions and methods as possible and then compared with each other and with theoretical results. The reevaluated data for both local fully developed and average Nusselt numbers in the turbulent flow region were found still to have considerable spread, with the bulk of the data being lower than predicted by existing analysis. An equation based on empirical grounds which represents most of the fully developed heat-transfer data is nu = 0.625 pe(0.4) where nu represents the Nusselt number and pe the Peclet number. The theoretical prediction of the heat transfer in the entrance region was found to give lower values, in most cases, than those found in the experimental work.

Lubarsky, Bernard↗
NASA NTRS1918

Experimental research on air propellers

The purposes of the experimental investigation on the performance of air propellers described in this report are as follows: (1) the development of a series of design factors and coefficients drawn from model forms distributed with some regularity over the field of air-propeller design and intended to furnish a basis of check with similar work done in other aerodynamic laboratories, and as a point of departure for the further study of special or individual types and forms; (2) the establishment of a series of experimental values derived from models and intended for later use as a basis for comparison with similar results drawn from certain selected full-sized forms and tested in free flight.

Durand, William F↗
NASA NTRS1935

Experimental Verification of the Theory of Wind-Tunnel Boundary Interference

The results of an experimental investigation on the boundary-correction factor are presented in this report. The values of the boundary-correction factor from the theory, which at the present time is virtually completed, are given in the report for all conventional types of tunnels. With the isolation of certain disturbing effects, the experimental boundary-correction factor was found to be in satisfactory agreement with the theoretically predicted values, thus verifying the soundness and sufficiency of the theoretical analysis. The establishment of a considerable velocity distortion, in the nature of a unique blocking effect, constitutes a principal result of the investigation.

Theodorsen, Theodore↗
NASA NTRS1937

An analytical and experimental study of the effect of periodic blade twist on the thrust, torque, and flapping motion of an autogiro rotor

An analysis is made of the influence on autogiro rotor characteristics of a periodic blade twist that varies with the azimuth position of the rotor blade and the results are compared with experimental data. The analysis expresses the influence of this type of twist upon the thrust, torque, and flapping motion of the rotor. The check against experimental data shows that the periodic twist has a pronounced influence on the flapping motion and that this influence is accurately predicted by the analysis. The influence of the twist upon the thrust and torque could be demonstrated only indirectly, but its importance is indicated.

Wheatley, John B↗
NASA NTRS1951

A study of the use of experimental stability derivatives in the calculation of the lateral disturbed motions of a swept-wing airplane and comparison with flight results

An investigation was made to determine the accuracy with which the lateral flight motions of a swept-wing airplane could be predicted from experimental stability derivatives, determined in the 6-foot-diameter rolling-flow test section and 6 by 6-foot curved-flow test section of the Langley stability tunnel. In addition, determination of the significance of including the nonlinear aerodynamic effects of sideslip in the calculations of the motions was desired. All experimental aerodynamic data necessary for prediction of the lateral flight motions are presented along with a number of comparisons between flight and calculated motions caused by rudder and aileron disturbances.

Bird, John D↗
NASA NTRS1954

Theoretical and Experimental Investigation of Mufflers with Comments on Engine-Exhaust Muffler Design

Equations are presented for the attenuation characteristics of single-chamber and multiple-chamber mufflers of both the expansion-chamber and resonator types, for tuned side-branch tubes, and for the combination of an expansion chamber with a resonator. Experimental curves of attenuation plotted against frequency are presented for 77 different mufflers with a reflection-free tailpipe termination. The experiments were made at room temperature without flow; the sound source was a loud-speaker. A method is given for including the tailpipe reflections in the calculations. Experimental attenuation curves are presented for four different muffler-tailpipe combinations, and the results are compared with the theory. The application of the theory to the design of engine-exhaust mufflers is discussed, and charts are included for the assistance of the designer.

Davis, Don D , Jr↗
NASA NTRS1955

A Theoretical and Experimental Investigation of the Lift and Drag Characteristics of Hydrofoils at Subcritical and Supercritical Speeds

A theoretical and experimental investigation at subcavitation speeds was made of the effect of the free-water surface and rigid boundaries on the lift and drag of an aspect-ratio-10 hydrofoil at both subcritical and supercritical speeds and of an aspect ratio-4 hydrofoil at supercritical speeds. Approximate theoretical solutions for the effects of the free-water surface and rigid boundaries on drag at subcritical speeds are developed. An approximate theoretical solution for the effects of these boundaries on drag at subcritical speeds is also presented. The agreement between theory and experiment at both supercritical and subcritical speeds is satisfactory for engineering calculations of hydrofoil characteristics from aerodynamic data. The experimental investigation indicated no appreciable effect of the limiting speed of wave propagation on lift-curve slope or angle of zero lift. It also showed that the increase in drag as the critical speed is approached from the supercritical range is gradual. The result is contrary to the abrupt increase at the critical speed predicted by theory.

Wadlin, Kenneth L↗
NASA NTRS1955

An Experimental Study of Applied Ground Loads in Landing

Results are presented of an experimental investigation made of the applied ground loads and the coefficient of friction between the tire and the ground during the wheel spin-up process in impacts of a small landing gear under controlled conditions on a concrete landing strip in the Langley impact basin. The basic investigation included three major phases: impacts with forward speed at horizontal velocities up to approximately 86 feet per second, impacts with forward speed and reverse wheel rotation to simulate horizontal velocities up to about 273 feet per second, and spin-up drop tests for comparison with the other tests. In addition to the basic investigation, supplementary tests were made to evaluate the drag-load alleviating effects of prerotating the wheel before impact so as to reduce the relative velocity between the tire and ground. In the presentation of the results, an attempt has been made to interpret the experimental data so as to obtain some insight into the physical phenomena involved in the wheel spin-up process.

Milwitzky, Benjamin↗
NASA NTRS1954

An Experimental Investigation of Reduction in Transonic Drag Rise at Zero Lift by the Addition of Volume to the Fuselage of a Wing-body-tail Configuration and a Comparison with Theory

An experimental investigation was made by the free-fall recoverable-model technique to assess at zero lift the possibilities of reducing the drag-rise coefficients of a wing-body-cruciform-tail combination by adding volume to the fuselage. The basic features of the test model were an unswept aspect-ratio-3.1 thin wing, a fineness-ratio-12.4 fuselage, and four 45 degrees sweptback tail surfaces. The tests covered a Mach number range of 0.84 to 1.15 with Reynolds numbers of 6.000.000 to 14,000,000, based on the wing mean aerodynamic chord. Considerable reduction in drag-rise coefficient was effected for several different modifications by the addition of properly distributed volume to the fuselage. In one instance, a reduction in drag coefficient was obtained by adding a volume which was almost four times the exposed wing volume. The computation method presented in NACA RM A53H17 generally predicted the supersonic drag-rise coefficients for each modification within 20 percent of the experimental values. As in the above-mentioned report, the predictions at a Mach number of one were not accurate. The changes in drag-rise coefficients resulting from the modifications were generally predicted with better accuracy than the values of drag-rise coefficients.

Holdaway, George H↗
NASA NTRS1958

Design and experimental investigation of a single-stage turbine with a rotor entering relative Mach number of 2

The design and experimental investigation of a single-stage supersonic turbine are presented herein. The turbine was designed for a rotor entering relative Mach number of 2. The maximum equivalent specific work output of the turbine at design speed and approximately design over-all pressure ratio was 32.9 BTU per pound at a static efficiency of 0.414. This static efficiency gave good verification to an independent reference that indicated theoretical static efficiencies for similar single-stage turbines within the range 0.40 to 0.45. An experimental ratio of effective rotor blade momentum thickness to mean camber length was determined to be 0.0014, which compares favorably with the results obtained from several transonic and subsonic turbines. The design procedure for this turbine would have been improved by allowing for more rotor losses by assuming a value of this momentum parameter comparable with those obtained from transonic turbines. Removing a large portion of the rotor suction surface enabled a lower static pressure to be felt at the stator exit, at the expense of higher rotor losses. The net result was an improvement in turbine work output of about 3 percent at design setting conditions. No problems associated with supersonic starting were encountered even under the worst conditions of turbine operation with respect to this problem.

Moffitt, Thomas P↗
NASA NTRS1955

An Experimental Investigation of the Hinge-moment Characteristics of a Constant-chord Control Surface Oscillating at High Frequency

The results of an experimental investigation of the hinge-moment characteristics of a constant-chord control surface oscillating at high frequency is presented. The control surface was mounted on an aspect-ratio-2 triangular wing. The aerodynamic restoring-moment coefficient and damping-moment coefficient were determined at a frequency of 260 cycles per second for a Mach number range of 0.6 to 0.8 and 1.3 to 1.9 at angles of attack of 5 degrees and 10 degrees. The test results showed linear theory to be a reliable guide to the prediction of the trend of the restoring-moment coefficient with Mach number for the supersonic speed range of the investigation but overestimated the magnitude of the coefficient. The experimental values of the damping-moment coefficient were, for the most part, more positive than those indicated by the theory and, for some conditions, could lead to instability of the control surface. Comparison of the results of this investigation with those of previous investigations at 0 and 50 cycles per second showed that frequency had little effect on the restoring-moment coefficient. The damping-moment coefficient was similarly insensitive to frequency at an oscillation amplitude of plus-or-minus 1.0 degrees but at an amplitude ofplus-or-minus 2.5 degrees the results showed a destabilizing shift with increasing frequency.

Reese, David E JR↗
NASA NTRS1956

Component Performance Investigation of J71 Experimental Turbine. Iv-effect of First-stator Adjustment; Over-all Performance of J71-97 Turbine with 132-percent-design Stator Area

An experimental invesitgation of the effect of increasing the first-stator area of the J71-97 experimental three-stage turbine from 97 percent of design to 132 percent revealed (1) the maximum efficiency obtained decreased from 0.891 to 0.869, (2) the choking equivalent weight flows increased by approximately 13.6 percent, and (3) at the turbine match points required to maintain the compressor at constant design equivalent conditions the turbine efficiency decreased from 0.87 to 0.86.

TURBINES -ALLISON J-71↗
NASA NTRS1993

New experimental techniques for solar cells

Solar cell capacitance has special importance for an array controlled by shunting. Experimental measurements of solar cell capacitance in the past have shown disagreements of orders of magnitude. Correct measurement technique depends on maintaining the excitation voltage less than the thermal voltage. Two different experimental methods are shown to match theory well, and two effective capacitances are defined for quantifying the effect of the solar cell capacitance on the shunting system.

Lenk, R.↗