Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “difference”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Effect of different stages of deformation on the microstructure evolution of Ti-rich NiTi shape memory alloy

The main objective of this work was to investigate the thermomechanical behavior and microstructural changes of a Ti-rich NiTi shape memory alloy (SMA). The microstructural and texture evolution of aged NiTi alloy at different degrees of deformation were elicited by transmission electron microscopy (TEM). An effort was made to correlate results obtained from the tensile test with results from microstructure studies. The undeformed sample reveals a self-accommodated morphology with straight and well defined twin boundaries. At different stages of deformation, diverse mechanisms were involved. These mechanisms include marstraining, detwinning accompanied by dislocation movement, and finally, severe plastic deformation, subdivision and amorphization of the matrix. Under increasing strains, high density lattice defects were generated and the morphology of B19’ became disordered. - Graphical abstract: The summary of microstructure changes of the martensite twins during tensile deformation in polycrystalline NiTi SMAs. - Highlights: • Initial elastic response, dislocation avalanche and deformation bands were studied. • < 011 > Type II twin accompanied by detwinned area after 2% cold work was observed. • Visible parallel fine stacking faults showed plastic flow of the material. • At higher strains, subgrains changed to recrystallized, finely amorphous structure.

36 MATERIALS SCIENCE↗

Microstructures of chemical vapor deposited high-purity tungsten achieved by two different precursors

Highlights: • CVD tungsten used as electron emitters of thermionic fuel elements was investigated. • Microstructures were characterized with metallography analysis. • The preferred orientation was determined with XRD and EBSD. • The surface morphology was observed with SEM and WLI. • Tungsten via thermolysis of WCl{sub 6} is better for thermionic fuel elements. - Abstract: Chemical vapor deposited (CVD) high-purity tungsten can be manufactured as electron emitters in thermionic fuel elements. Exposed surface planes of the emitter emit electrons and affect the efficiency and load capacity of the thermionic fuel element. In order to determine the electron emission planes of the emitter, the metallurgic structures, the preferred orientation and the as-deposited surface morphology of CVD tungsten have been investigated. In this work, high-purity (over 99.99%) tungsten was achieved by two different precursors: hydrogen reduction of tungsten hexafluoride (WF{sub 6}) and thermolysis of tungsten hexachloride (WCl{sub 6}). The microstructures of CVD tungsten were characterized by metallography analysis, X-ray diffraction (XRD), electron backscattered diffraction (EBSD), and white light interference (WLI). Tungsten fabricated by hydrogen reduction of WF{sub 6} and thermolysis of WCl{sub 6} has <100>-preferred columnar microstructures. However, the latter exhibits larger columnar grains and preferred <100> less. The preferred orientation is caused by the higher growth rate of the <100> orientation and competition between the <100> orientations of different grains. The as-deposited surface consists of tiny pyramids, with <100> axis and {111} side faces. In contrast to tungsten produced by hydrogen reduction of WF{sub 6}, the pyramid on tungsten synthesized via thermolysis of WCl{sub 6} contains small {110} facets on the four edges. Therefore, tungsten made via thermolysis of WCl{sub 6} is a better candidate for thermionic fuel elements, because the higher work function of {110} planes enables better output efficiency.

36 MATERIALS SCIENCE↗

Microstructure characterization and nano & micro hardness of tri-modal microstructure of titanium alloy under different hot working conditions

Highlights: • The contents and sizes of α{sub p} and α{sub l} are determined by the processing parameters of first and second step. • The morphology of α{sub s} embedded in β phase is determined by the accumulated distortional strain energy and dislocations. • α{sub p} becomes harder as the strain rate of the first step increases due to the constantly enhanced work hardening effect. • β{sub t} is always harder than α{sub p} and α{sub l} due to the interfacial-strengthening effect. • The hardness of α{sub l} makes the greatest contribution in the integrated hardness of tri-modal microstructure. - Abstract: In this work, the dependences of tri-modal microstructure parameters and corresponding nano & micro hardness on through-process processing parameters were quantitatively studied during the three-step thermo-mechanical processing of TA15 titanium alloy. It is found that the processing parameters of first step, especially for the deformation temperature and strain rate, mainly affect primary equiaxed α (α{sub p}) through the α → β phase transformation and the competition between dynamic recovery and dynamic recrystallization. The second processing step primarily affects the content and thickness of lamellar α (α{sub l}). In the third processing step, compared with low-temperature aging, normal annealing provides sufficient driving force for α{sub l} and secondary lamellar α (α{sub s}) growing, which leads to thicker α{sub l} and α{sub s}. As for the nano & micro hardness, in one sample undergoing different process, transformed β matrix (β{sub t}) is always harder than α{sub l} and α{sub s} due to the interfacial-strengthening effect. In addition, with increasing strain rate of the first step, α{sub p} becomes harder due to the constantly enhanced work hardening effect while the hardness of β{sub t} varies little because of the competition between interfacial strengthening and distribution disorder degree. However, the nano hardness of α{sub l} decreases firstly and then increases with strain rate, which presents the same trend with the micro hardness of integrated hardness at different processing conditions.

36 MATERIALS SCIENCE↗

Comparison of aluminium foams prepared by different methods using X-ray tomography

Highlights: • The closed porosity of MF aluminium foam is much lower than GI aluminium foam at a similar overall porosity. • There are more micropores in cell walls of MF aluminium foams than that in GI aluminium foams. • GI method is more suitable to prepare aluminium foams with high porosity under a similar cell size condition. • The thickness difference between normal cell wall and Plateau border is greater in GI foams compared to MF foams. - Abstract: The cell structure and mechanical properties of aluminium foams prepared by melt foaming (MF) method are supposed to be better than the ones produced by gas injection (GI) method. Preparation processes of these two methods have been developed during the last recent years. Mechanical properties of aluminium foams depend strongly on characteristics of the cell structure. Therefore, it is necessary to compare cell structures of the foams fabricated with these two methods quantitatively using X-ray computed tomography and this is the purpose of the present paper. MF and GI foams have thus been prepared. True density measurements and cell structures indicate that the volume fraction of the closed cells of MF foam with high porosity is negligible. By contrast, the majority of cells of GI foam are closed. Results of cell structure analysis show that there are more micropores in cell walls of the foams prepared by MF method compared to the ones prepared by GI method, especially for the MF foams with low porosity. In addition, results of cell size study show that the cell size distribution is wide in dynamic GI foams, and there are usually big holes inside MF foams. GI method is more suitable to prepare aluminium foams with high porosity compared to MF method. Furthermore, the thickness difference between normal cell wall and Plateau border is greater in GI foams, in particular for the ones produced by the static injector.

36 MATERIALS SCIENCE↗

Crystal development during carbonation of lime-based mortars in different environmental conditions

Highlights: • High CO{sub 2} and DiloCarb® treatment favour advanced carbonation and self-healing. • In the lime mortar without ceramics, channel type pores occur in the aggregate border. • In the lime mortars with ceramics, vug type pores are produced in the binder during kneading. • The formation of tabular CaCO{sub 3} polymorphs caused an increase in stress leading to microshrinkage cracks. • The use of a ceramic provoked dissolution and then re-precipitation of more stable polymorphs. - Abstract: This study examines crystal development during the carbonation of lime mortars according to the additives used and curing conditions. Two types of samples were prepared, one with sand and the other one additionally including Roman ceramics. These mortars were cured: 1) by spraying with a carbonation accelerator product under laboratory conditions; 2) in a climate chamber under 20 °C, 60% relative humidity, and 1600 ppm CO{sub 2}; and 3) under laboratory conditions as controls. Polarized light microscopy, SEM-EDS and XRD were used at 28, 90, 120 and 180 days to monitor the carbonation process. Observations indicate the development of different CaCO{sub 3} polymorphs, which appeared as metastable phases. The early nucleation of a well-defined calcite phase as the most stable CaCO{sub 3} polymorph was only identified in the chamber-cured samples. Differences in the pore network were observed depending on the composition and morphology of the mortar components and the environmental curing conditions.

36 MATERIALS SCIENCE↗

Microstructure and texture evolution of duplex stainless steels with different molybdenum contents

Highlights: • The 3.05Mo steel has higher resistance to strain-induced transformation than the 0.28Mo steel. • The increased Mo content affects the grain growth of austenite and ferrite due to the effects of segregation and anchoring. • At high annealing temperatures, this Mo retarding effect is weakened. • The suppression of γ-fiber development in the ferrite texture is associated with the increased Mo content. • High amounts of Mo generate unfavorable conditions for the formation of CSL boundaries. - Abstract: The microstructure and texture evolution of duplex stainless steels with different molybdenum contents were studied. For this purpose, hot-rolled 2205 and 2304 samples were solution-annealed at 1100 °C for 1800 s and then cold-rolled to a 75% thickness reduction. This was followed by an isothermal annealing at 900 and 1100 °C for 180 s. The EBSD technique was used to determine the phase ratio, crystallographic texture, and microstructural characteristics. The hot-rolled steel had a work hardened microstructure and the samples submitted to intermediate annealing presented mainly deformation-free grains. Cold rolling resulted in a substantial reduction in the phase spacing with the formation of the strain-induced α′-martensite (SIM) from the metastable austenite. After annealing at 900 °C, the ferrite grains retained the elongated shape of the cold-rolled condition and the primary recrystallization progressed in the austenite phase. Increasing the Mo content increased the resistance to strain-induced martensitic transformation and inhibited the grain growth of austenite phase during annealing at 900 °C. Increasing annealing temperature to 1100 °C promoted the coarsening of both bcc and fcc structures with the formation of annealing twins in the austenitic grains. The recrystallization kinetics and subsequent grain growth occur earlier in ferrite than in austenite phase. Differences in Mo content did not significantly alter the evolution of austenite texture, whereas in the ferrite phase the increase in Mo content suppressed the γ-fiber development. Oriented nucleation was the predominant mechanism observed during the recrystallization of ferritic grains in the 2205 samples. The development of ∑19a boundaries was associated with the selected growth of {554}<225>{sub α} grains in the annealed 2304 samples. Annealing twins were associated with the formation of Σ3 boundaries after the heat treatments. Grain coarsening resulted in a larger fraction of the special boundaries in ferrite phase but inhibited the CSL formation in the austenite phase.

36 MATERIALS SCIENCE↗

Characterization of the effects of different tempers and aging temperatures on the precipitation behavior of Al-Mg (5.25at.%)-Mn alloys

We investigated the effects of different tempers (H131 and H116) and different aging temperatures (50 and 70 °C) on the precipitation behavior of Al-Mg (5.25 at.%)-Mn (Al 5083) alloys aged for a long time (41 and 30 months) using electron backscatter diffraction(EBSD), scanning transmission electron microscopy(STEM), energy-dispersive X-ray spectroscopy(EDS), atom probe tomography (APT), and small angle neutron scattering (SANS). Results for the GP zones and β'' phases were found in Al 5083 H116 aged at 50 °C for 24 months using APT. EDS and SANS revealed that a phase transformation process from GP zones to β'/β phases occurred for precipitates formed in both Al 5083 H131 and H116 aged at 70 °C. The effective diffusion coefficient of Mg in Al 5083 H131 is 1.8 times of that in Al 5083 H116 aged at 70 °C. The precipitation process in Al 5083 H116 aged at 50 °C is much slower than that in the sample aged at 70 °C. Finally, we identified the coarsening process in Al 5083 H131 and H116 aged at 70 °C for > 9 months.

36 MATERIALS SCIENCE↗

Critical differences between electron beam melted and selective laser melted Ti-6Al-4 V

Effective optimization of the production of Ti-6Al-4 V using AM requires a fundamental understanding of the relative importance of different microstructural features to the deformation and failure mechanisms, particularly features that vary between production methods. In this study, the tensile response and deformation mechanisms of electron beam melted (EBM) AM Ti-6Al-4 V material loaded in different orientations and produced using various powder sizes were compared to those of selective laser melted (SLM) AM Ti-6Al-4 V material. The density and morphology of pores, phase fractions, prior-β grains, and defect microstructures were evaluated using scanning electron microscopy, X-ray computed tomography, electron backscatter diffraction, and transmission electron microscopy before and after deformation. The results were used to evaluate the relative importance of each feature on strengthening, deformation, and failure initiation mechanisms. Results focused primarily on coarse-powder EBM materials indicated that phase distribution and defect density were most influential for determining material yield strength as well as maximum possible strain to failure. Porosity was lower overall in EBM Ti-6Al-4 V than in SLM, allowing for occasional increases in part strain to failure, but remained a limiting factor determining overall part ductility.

36 MATERIALS SCIENCE↗

Synthesis of c-axis oriented AlN thin films on different substrates: A review

Highly c-axis oriented AlN thin films have been deposited by reactive sputtering on different substrates. The crystallographic properties of layered film structures consisting of a piezoelectric layer, aluminum nitride (AlN), synthesized on a variety of substrates, have been examined. Aluminum nitride thin films have been deposited by reactive pulsed-DC magnetron sputtering using an aluminum target in an Ar/N{sub 2} gas mixture. The influence of the most critical deposition parameters on the AlN thin film crystallography has been investigated by means of X-ray diffraction (XRD) analysis of the rocking curve Full-Width at Half Maximum (FWHM) of the AlN-(0 0 0 2) peak. The relationship between the substrate, the synthesis parameters and the crystallographic orientation of the AlN thin films is discussed. A guide is provided showing how to optimize these conditions to obtain highly c-axis oriented AlN thin films on substrates of different nature.

36 MATERIALS SCIENCE↗

Synthesis, characterization and evaluation of nano-zirconium vanadate ion exchanger by using three different preparation techniques

Sol-gel, homogeneous precipitation and hydrothermal synthesis are three different preparation techniques have been used as an attempt to synthesize nano-zirconium vanadate with properties suitable to be used as ion exchangers. The impact of the synthetic preparation variables such as the reactant concentrations, reaction temperature and reaction time on the ion exchange capacity of the produced ion exchanger has been considered for each preparation technique. One sample from each preparation technique having the largest ion exchange capacity has been selected to be physically and chemically characterized using various analytical techniques such as XRD, TGA, DSC, pH titration, FTIR and SEM in order to determine the properties of the ion exchanger produced from each technique. For all the studied ZrV samples it can be presumed that they have the ion exchange affinity sequences for alkali metal ions K > Na > Li, the order for the alkaline earth metals is Ba > Ca > Mg and their affinity for radioactive metals follow Cs > Sr. Moreover, the prepared materials are of high thermal and radiation stabilities. Also they have high chemical stabilities toward wide concentration ranges of acid, basic as well as polar solvents. It has been deduced from the X-ray analysis that ZrV produced from the sol-gel technique has an amorphous structural. While those produced from the homogeneous precipitation and hydrothermal synthesis techniques, in the nano-scale have semi-crystalline structural. Furthermore, SEM confirms that particle size of the all studied prepared ZrV samples have nano-diameters of range 50-60 nm. Specific surface area of the three different prepared ion exchangers are found to be equal to 187, 192 and 320 m{sup 2}/g for sol-gel, homogeneous precipitation and hydrothermal, respectively. A tentative structural formula of Zr(OH){sub 2}(HVO{sub 4}){sub 2}.2H{sub 2}O has been proposed for all studied samples on the basis of on FTIR, DSC and TGA results.

36 MATERIALS SCIENCE↗

A comparative study on the optical limiting properties of different nano spinel ferrites with Z-scan technique

Highlights: ► First report in which the optical limiting properties of five different nano spinel ferrites are compared. ► The obtained nonlinearity fits to a two-photon like absorption process. ► Except for NiFe{sub 2}O{sub 4}, the observed nonlinearity has contributions from excited state absorption. ► A size dependent optical limiting response is obtained. ► Among the investigated ferrites, ZnFe{sub 2}O{sub 4} is found to be a better candidate for the optical limiting applications. -- Abstract: We report the optical limiting properties of five different spinel ferrites, NiFe{sub 2}O{sub 4}, Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4}, ZnFe{sub 2}O{sub 4}, Ni{sub 0.5}Co{sub 0.5}Fe{sub 2}O{sub 4}, and CoFe{sub 2}O{sub 4} with an average particle grain size of 8 nm. The optical limiting properties are investigated using the open aperture Z-scan technique. The obtained nonlinearity fits to a two-photon like absorption process. Except for NiFe{sub 2}O{sub 4}, the observed nonlinearity has contributions from excited state absorption. The optical limiting response is also studied against particle size and the nonlinearity is found to increase with increasing particle size within the range of our investigations. On comparing the optical limiting properties, ZnFe{sub 2}O{sub 4} is found to be a better candidate for the optical limiting applications. To the best of our knowledge, this is the first report where the optical limiting properties of spinel ferrites are compared.

36 MATERIALS SCIENCE↗

Controlled synthesis of different morphologies of TiB{sub 2} microcrystals by aluminum melt reaction method

Highlights: ► TiB{sub 2} microcrystals with different morphologies were synthesized. ► The growth of TiB{sub 2} is controlled by two-dimensional nucleation in Al melt. ► The growth of the hierarchical TiB{sub 2} microcrystals is controlled by two steps. - Abstract: TiB{sub 2} microcrystals with different morphologies, including hexagonal plate-like, tower-like and dendritic, were fabricated by aluminum melt reaction method in this study. The growth mechanisms of these microcrystals are also discussed based on the fundamental crystal growth theories. It is found that the growth of TiB{sub 2} is controlled by two-dimensional nucleation in aluminum melt. If the atomic concentration, reaction rate and atomic diffusion rate in the melt are high, TiB{sub 2} microcrystals exhibit hierarchical tower-like and dendritic morphologies. Otherwise, the single crystal of hexagonal plate-like morphology is obtained. The growth of the hierarchical TiB{sub 2} microcrystals is controlled by two steps, intermittent two-dimensional nucleation and continuous lateral spreading of layers on the growth faces.

36 MATERIALS SCIENCE↗

A facile liquid phase exfoliation method to prepare graphene sheets with different sizes expandable graphite

Graphical abstract: - Highlights: • This study presented a novel method for the production of high-quality graphene sheets through the exfoliation of Li-intercalated EG with sonication. • The quality of the graphene sheets produced from different sizes EG was compared for the first time and the formation mechanism was discussed. • The graphene sheets obtained from the small size EG have less layers than the large size EG. - Abstract: In this work, graphene sheets suspension were synthesized directly from expandable graphite (EG) via an intercalation and exfoliation pathway using n-butyl lithium as the intercalating agent, water and N,N-dimethylformamide (DMF) as the exfoliating agent. The quality of the graphene sheets produced from different sizes EG was compared and the formation mechanism was discussed. The formation of the graphene sheets and its formation mechanism were confirmed by transmission electron microscopy (TEM), high-resolution TEM (HRTEM), selected area electron diffraction (SAED), Raman spectroscopy measurement, inductively coupled plasma atomic emission spectrometry (ICP-AES) and thermogravimetric analysis (TGA). The graphene sheets obtained from the small size EG have less layers than the large size EG.

36 MATERIALS SCIENCE↗

Synthesis and investigation of optical properties of TOPO-capped CuInS{sub 2} semiconductor nanocrystal in the presence of different solvent

Graphical abstract: - Highlights: • TOPO-capped CuInS{sub 2} nanoparticles were synthesized by injection method. • Pure CuInS{sub 2} nanoparticle was obtained by injection in 200 °C. • The size, shape and optical properties of products were controlled. • Nanoparticles with size smaller than 10 nm and wurtzite phase was obtained. • The absorption and PL spectra of CuInS{sub 2} nanoparticles were tunable. - Abstract: In this work, synthesis of CuInS{sub 2} semiconductor nanoparticles by thermolysis of a mixed solution of CuAc, In(Ac){sub 3} and DDT in coordinating solvent and trioctylphosphine oxide (TOPO) as ligand was developed. CuInS{sub 2} nanoparticles with size of −10 nm and nanorods were obtained and optical properties controlled by adjusting the reaction parameters such as temperature and time. Also the shape of nanoparticles was controlled by various solvents elaborately. The as-prepared nanoparticles were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Scanning electron microscopy (SEM), UV–vis absorption, and photoluminescence (PL) spectroscopy. With the use of different solvent different morphology obtained. In the presence of oleylamine/octadecene rectangle-like nanorods obtained while with the use of oleic acid sphere-like nanoparticles achieved.

36 MATERIALS SCIENCE↗

Study of Eu{sup 3+} → Eu{sup 2+} reduction in BaAl{sub 2}O{sub 4}:Eu prepared in different gas atmospheres

Highlights: • The effect of different gas atmospheres on the Eu reduction process was studied. • The Eu reduction was monitored analyzing XANES region at the Eu L{sub III}-edge. • Hydrogen reducing agent are the most appropriate gas for Eu{sup 2+} stabilization. • Only a part of the Eu ions can be stabilized in the divalent state. • A model of Eu reduction process is proposed. - Abstract: The effect of different gas atmospheres such as H{sub 2}(g), synthetic air, carbon monoxide (CO) and nitrogen (N{sub 2}) on the Eu{sup 3+} → Eu{sup 2+} reduction process during the synthesis of Eu-doped BaAl{sub 2}O{sub 4} was studied using synchrotron radiation. The Eu{sup 3+} → Eu{sup 2+} reduction was monitored analyzing XANES region when the sample are excited at the Eu L{sub III}-edge. The results show that the hydrogen reducing agent are the most appropriate gas for Eu{sup 2+} stabilization in BaAl{sub 2}O{sub 4} and that only a part of the Eu ions can be stabilized in the divalent state. A model of Eu reduction process, based on the incorporation of charge compensation defects, is proposed.

36 MATERIALS SCIENCE↗

Electrical properties of AC{sub 3}B{sub 4}O{sub 12}-type perovskite ceramics with different cation vacancies

Highlights: • AC{sub 3}B{sub 4}O{sub 12} perovskite with different concentration cation vacancies were prepared. • Cell parameter decreases with the increase of concentration of cation vacancies. • PTCO and CTO remain high dielectric permittivity but depress loss greatly. • Dielectric loss associates with cation vacancies and motion of oxygen vacancies. - Abstract: AC{sub 3}B{sub 4}O{sub 12}-type perovskite CaCu{sub 3}Ti{sub 4}O{sub 12} (CCTO), □{sub 0.34}Pr{sub 0.67}Cu{sub 3}Ti{sub 4}O{sub 12} (PCTO), □{sub 1}Cu{sub 3}Ta{sub 2}Ti{sub 2}O{sub 12} (CTTO), □{sub 2}Cu{sub 2}Ta{sub 4}O{sub 12} (CTO) ceramics with different concentration cation vacancies were prepared through traditional solid state reaction method. X-ray diffraction analysis indicated that CCTO and PCTO are perovskite cubic with space group Im-3 (no. 204) while CTTO and CTO are Pm-3 (no. 200). Cell parameter of the samples dramatically increases with the increase of cation vacancies. Dielectric permittivity of them maintains very high value of ∼10{sup 4} from room temperature to 550 K but the dielectric loss is depressed with the increase of cation vacancies in the same space group. The dielectric properties and conductivity behavior were described by the Debye relaxation and the universal dielectric response, respectively. The effect mechanism of cation vacancy and crystal structure on carrier transposition were discussed.

36 MATERIALS SCIENCE↗

Core–shell Ag@SiO{sub 2} nanoparticles of different silica shell thicknesses: Preparation and their effects on photoluminescence of lanthanide complexes

Highlights: • Ag@SiO{sub 2} nanoparticles of different silica shell thicknesses were prepared via the Stöber process. • Sm and Dy complexes with benzoate, 1,10-phenanthroline and 2,2′-bipyridine were synthesized. • The complex-doped Ag@SiO{sub 2} composites show stronger luminescent intensities than pure complexes. • The luminescent intensities of the composites strongly depend on the SiO{sub 2} shell thickness. - Abstract: Three kinds of almost spherical core–shell Ag@SiO{sub 2} nanoparticles of different silica shell thicknesses (10, 25 and 80 nm) were prepared via the Stöber process. The Ag core nanoparticles were prepared by reducing silver nitrate with sodium citrate. The size, morphology and structure of core–shell Ag@SiO{sub 2} nanoparticles were characterized by transmission electron microscopy. Subsequently, eight kinds of lanthanide complexes with benzoate, 1,10-phenanthroline and 2,2′-bipyridine were synthesized. The composition of the lanthanide complexes was characterized by elemental analysis, IR and UV spectra. Finally, lanthanide complexes were attached to the surface of Ag@SiO{sub 2} nanoparticles to form lanthanide-complex-doped Ag@SiO{sub 2} nanocomposites. The results show that the complex-doped Ag@SiO{sub 2} nanocomposites display much stronger luminescence intensities than the lanthanide complexes. Furthermore, the luminescence intensities of the lanthanide-complex-doped Ag@SiO{sub 2} nanocomposites with SiO{sub 2} shell thickness of 25 nm are stronger than those of the nanocomposites with SiO{sub 2} shell thickness of 10 and 80 nm.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

High-temperature electrochemical performance of low-cost La–Ni–Fe based hydrogen storage alloys with different preparation methods

Highlights: • Effects of four different preparation processes were studied at 20/60 °C. • All NS + HT, RS and RS + HT processes can optimize the thermodynamic performance. • The HT process can provoke the precipitation of A{sub 2}B{sub 7} and leads to a poor cycling life. • Al exhibits the most remarkable dissolution for all the alloys, especially at 60 °C. - Abstract: In order to optimize the microstructure and high temperature electrochemical performances of low-cost AB{sub 5}-type Ml(NiMnAl){sub 4.2}Co{sub 0.3}Fe{sub 0.5} hydrogen storage electrode alloys, four different preparation methods including normal solidification (NS), normal solidification and 900 °C heat treatment (NS + HT), rapid solidification (RS), rapid solidification and 900 °C heat treatment (RS + HT) were adopted in this work. All alloys exhibit CaCu{sub 5} type hexagonal structure and there is a small amount of A{sub 2}B{sub 7} phase in NS + HT and RS + HT alloys. It is found the using of HT process can decrease the hydrogen equilibrium plateau pressure, the plateau slope and hysteresis at 40, 60 and 80 °C. The NS + HT and RS + HT alloys also possess better activation, high rate discharge performance, larger discharge capacity, but poor cycling performance due to the existence of A{sub 2}B{sub 7} phase which can accelerate dissolution of Ni, Mn and Fe elements in KOH alkaline electrolyte. The RS process can make alloy exhibit the best cycling performance especially at 60 °C.

36 MATERIALS SCIENCE↗