Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “conditional probability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Problems with aging wiring in Naval aircraft

The Navy is experiencing a severe aircraft electrical wiring maintenance problem as a result of the extensive use of an aromatic polyimide insulation that is deteriorating at a rate that was unexpected when this wire was initially selected. This problem has significantly affected readiness, reliability, and safety and has greatly increased the cost of ownership of Naval aircraft. Failures in wire harnesses have exhibited arcing and burning that will propagate drastically, to the interruption of many electrical circuits from a fault initiated by the failure of deteriorating wires. There is an urgent need for a capability to schedule aircraft rewiring in an orderly manner with a logically derived determination of which aircraft have aged to the point of absolute necessity. Excessive maintenance was demonstrated to result from the accelerated aging due to the parameters of moisture, temperature, and strain that exist in the Naval Aircraft environment. Laboratory studies have demonstrated that MIL-W-81381 wire insulation when aged at high humidities followed the classical Arrhenius thermal aging relationship. In an extension of the project a multifactor formula was developed that is now capable of predicting life under varying conditions of these service parameters. An automated test system has also been developed to analyze the degree of deterioration that has occurred in wires taken from an aircraft in order to obtain an assessment of remaining life. Since it is both physically and financially impossible to replace the wiring in all the Navy's aircraft at once, this system will permit expedient scheduling so that those aircraft that are most probable to have wiring failure problems can be overhauled first.

Campbell, Frank J.↗
NASA NTRS2000

Measurement and Modeling of Steep Ocean Wave Slopes

Our study emphasizes the importance of identifying and quantifying the distribution variance, skewness and kurtosis from optical and microwave scattering observations. Recent field measurements of the sea slope distribution for intermediate-to-long scale gravity waves will be presented. These data were collected using an airborne laser range system designed to estimate the surface slope vector at horizontal scales of 1-2 m. The observed slope distribution tail indicates that the occurrence of steep waves substantially exceeds a Gaussian prediction. This measured peakedness is present over the wide range of sea state and wind speed conditions encountered. Data are further evaluated within the context of Cox and Munk's well-known sea slope investigations. Based on a re-evaluation of the Cox and Munk's reported parameters, we find a consistent picture develops wherein data are shown to consistently indicate non-Gaussian statistics. One fundamental application of such a non-Gaussian slope observation is its place in modifying predicted wave breaking probability to help to better quantify gas transfer processes at the sea surface.

Chapron, B.↗
NASA NTRS1987

Oxidative processes in soybean and pea seeds: effect of light, temperature, and water content

Oxidative processes are probable determinants of longevity of seeds in storage. Measurements of actual oxygen uptake rates were made for soybean and pea seeds as a comparison of short and long lived seeds when light, temperature, and moisture contents were varied. In both peas and soybeans, the oxygen uptake was depressed at low temperatures (<16 degrees C) and low water contents (< 0.25 gram H2O per gram dry weight). Apparent activation energies under these conditions are very high, while apparent activation energies of seeds at higher water contents and at temperatures greater than 22 degrees C are much less. Light enhances the level of oxygen uptake in pea, but reduces the level of oxygen uptake in soybean. The complexities of the interactions of oxygen uptake with environmental conditions in soybean compared to pea suggest that oxidative processes occur in soybean at low water contents, but are essentially absent in pea. It is suggested that the additional oxidative processes in soybean with moisture contents between 0.10 and 0.24 gram per gram may contribute to the poorer longevity of soybean seed compared to pea seed.

NASA Program Space Biology↗
NASA NTRS1948

Ditching Tests of a 1/20-Scale Model of the Northrop B-35 Airplane

Tests of a 1/20-scale dynamically similar model of the Northrop B-35 airplane were made to study its ditching characteristics. The model was ditched in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds,and conditions of damage were simulated during the investigation. The ditching characteristics were determined by visual observation and from motion-picture records and time-history acceleration records. Both longitudinal and lateral accelerations were measured. Results are given in tabular form and time-history acceleration curves and sequence photographs are presented. Conclusions based on the model investigation are as follows: 1. The best ditching of the B-35 airplane probably can be made by contacting the water in a near normal landing attitude of about 9 deg with the landing flaps full down so as to have a low horizontal speed. 2. The airplane usually will turn or yaw but the motion will not be violent. The maximum lateral acceleration will be about 2g. 3. If the airplane does not turn or yaw immediately after landing, it probably will trim up and then make a smooth run or porpoise slightly. The maximum longitudinal decelerations that will be encountered are about 6g or 7g. 4. Although the decelerations are not indicated to be especially large, the construction of the airplane is such that extensive damage is to be expected, and it probably will be difficult to find ditching stations where crew members can adequately brace themselves and be reasonably sure of avoiding a large inrush of water.

Fisher, Lloyd J.↗
NASA NTRS2008

Assessment of Medical Risks and Optimization of their Management using Integrated Medical Model

The Integrated Medical Model (IMM) Project is a software-based technique that will identify and quantify the medical needs and health risks of exploration crew members during space flight and evaluate the effectiveness of potential mitigation strategies. The IMM Project employs an evidence-based approach that will quantify probability and consequences of defined in-flight medical risks, mitigation strategies, and tactics to optimize crew member health. Using stochastic techniques, the IMM will ultimately inform decision makers at both programmatic and institutional levels and will enable objective assessment of crew health and optimization of mission success using data from relevant cohort populations and from the astronaut population. The objectives of the project include: 1) identification and documentation of conditions that may occur during exploration missions (Baseline Medical Conditions List [BMCL), 2) assessment of the likelihood of conditions in the BMCL occurring during exploration missions (incidence rate), 3) determination of the risk associated with these conditions and quantify in terms of end states (Loss of Crew, Loss of Mission, Evacuation), 4) optimization of in-flight hardware mass, volume, power, bandwidth and cost for a given level of risk or uncertainty, and .. validation of the methodologies used.

Fitts, Mary A.↗
NASA NTRS2012

Ground-Based Centimeter, Millimeter, and Submillimeter Observations of Recent Comets

Comets provide important clues to the physical and chemical processes that occurred during the formation and early evolution of the Solar System, and could also have been important for initiating prebiotic chemistry on the early Earth [I]. Comets are comprised of molecular ices, that may be pristine interstellar remnants of Solar System formation, along with high-temperature crystalline silicate dust that is indicative of a more thermally varied history in the protosolar nebula [2]. Comparing abundances of cometary parent volatiles, and isotopic fractionation ratios, to those found in the interstellar medium, in disks around young stars, and between cometary families, is vital to understanding planetary system formation and the processing history experienced by organic matter in the so-called interstellar-comet connection [3]. In the classical picture, the long-period comets probably formed in the nebular disk across the giant planet formation region (5-40 AU) with the majority of them originating from the Uranus-Neptune region. They were subsequently scattered out to the Oort Cloud (OC) by Jupiter. The short-period comets (also known as ecliptic or Jupiter Family Comets - JFC) reside mainly in the Edgeworth-Kuiper belt where they were formed. Given the gradient in physical conditions expected across this region of the nebula, chemical diversity in this comet population is to be expected [4,5]. We have conducted observations of comets I 03P/Hartley 2 (JFC) and C/2009 PI (Garradd) (OC), at primarily millimeter and submillimeter wavelengths, to determine important cosmogonic quantities, such as the ortho:para ratio and isotope ratios, as well as probe the origin of cometary organics and if they vary between the two dynamic reservoirs.

Milam, S. N.↗
DOE OSTI2025

Statistical evaluation of microscale stress conditions leading to void nucleation in the weak shock regime

Here, we investigate the heterogeneity of the stress state driven by anisotropic deformation response at the single crystal level through five statistical volume element (SVE) calculations of polycrystalline BCC tantalum. This work focuses on grain boundaries as a prominent material defect type prone to void nucleation based upon experimental observations of predominantly intergranular void nucleation in this material. The SVEs are constructed to be statistically representative of larger volumes of material and are meshed such that mean and standard deviation of grain size and orientation information is reconstructed. The computational meshes feature hexahedral (brick) elements and smooth conformal grain boundaries where significant stress concentration is known to occur, a tail effect of interest in the extreme events process of dynamic ductile damage. An existing micromechanical crystallographic plasticity model shown to capture the single crystal behavior of BCC tantalum well is used to perform the polycrystal calculations. The model includes representation of the non-Schmid effect of non-planar screw dislocation kinetics in tantalum. A three-dimensional stress state time profile predicted by damage modeling of a flyer plate impact experiment is applied as boundary conditions to each SVE. Resulting grain boundary stress state statistics are strongly non-Gaussian. Significant structural evolution is observed within the compressive hold before unloading into tension in the stress profile. Strong angular dependence of grain boundary traction magnitude with shock direction is observed. Non-Schmid effects continue to suggest their influence on propensity of microstructural defect types to nucleate voids. A general void nucleation criterion is proposed using probability theory. The general framework is specified to polycrystalline BCC tantalum in the weak shock regime to include the SVE calculations and literature molecular dynamics calculations of grain boundary void nucleation strength. Probability density functions (PDFs) are used to describe the interaction between the local stress state heterogeneity and the distributed grain boundary void nucleation strength state. A causation entropy maximization procedure removes the requirement for ad hoc selection of a PDF functional form and provides a rigorous procedure for data-based PDF determination. The resulting physically informed PDF describes the spatial appearance frequency of nucleated voids as a function of applied macroscale pressure. Lower length scale physics are thus packaged in a precise and computationally efficient way to provide computational plasticity insight to macroscale dynamic ductile damage models.

36 MATERIALS SCIENCE↗
NASA NTRS1969

Recovery considerations for possible high inclination long duration earth orbital missions

Problem areas are discussed and various solutions proposed. One of the major recovery problems encountered with missions having higher orbital inclinations than previous missions is the greater likelihood of severe weather conditions in the landing zones, especially if landing zones are optimized for orbital coverage considerations. Restricting the reentry window and increasing in-orbit wait times can partially eliminate the weather problem, but the possibility of emergency landings at higher latitudes still exists. It can be expected that the increased confidence level in spacecraft reliability that will exist by the time the high-inclination missions are flown will reduce the probabilities of an emergency landing in an unfavorable recovery location to a very low level.

Obriant, T. E.↗
NASA NTRS1973

Cosmic Ray Hysteresis as Evidence for Time-dependent Diffusive Processes in the Long Term Solar Modulation

A simple one-dimensional time-dependent diffusion-convection model for the modulation of cosmic rays is presented. This model predicts that the observed intensity at a given time is approximately equal to the intensity given by the time independent diffusion convection solution under interplanetary conditions which existed a time iota in the past, (U(t sub o) = U sub s(t sub o - tau)) where iota is the average time spent by a particle inside the modulating cavity. Delay times in excess of several hundred days are possible with reasonable modulation parameters. Interpretation of phase lags observed during the 1969 to 1970 solar maximum in terms of this model suggests that the modulating region is probably not less than 10 a.u. and maybe as much as 35 a.u. in extent.

Ogallagher, J. J.↗
NASA NTRS1984

Chondrule rims and interchondrule matrix in UOC

Opaque rims around chondrules and clasts were distinguished from opaque, interchondrule matrix apparently unrelated spatially to chondrules and clasts. Microprobe and electron microscope techniques were used. The mean chemical composition for dark rim and matrix in Bishunpur and Tieschitz are similar to the opaque matrix of Huss, et al. However, the mean dark rim compositions in Bishunpur have significantly higher Fe, and lower Na, K, Al and Si than opaque interchondrule matrix. The opaque matrix of Huss, et al, essentially lies between these compositions. In Tieschitz only rim material was observed. In Tieschitz the rims are Si-poor and dominated by normative olivine (Fo50). Again there is an Na, K, Al component but is often nepheline normative rather than albitic. It too is probably present as glass, Ashworth (pers.comm.). In Bishunpur rims as well as the silicate-FeS, FeNi layering described by Allen, et al, discontinuous layering was observed within the silicate portion. This is apparently due to variations in the proportions of the components, particularly in the glassy phase. In Bishunpur there is a strong genetic link between matrix and rims, although rims seem to have formed under different, possibly more oxidizing, conditions. Also the presence of the same component in rims, matrix chondrules, and clasts suggests a common source.

Alexander, C.↗
NASA NTRS1985

Failure detection and accommodation in structural dynamics systems using analytic redundancy

The concept of analytic redundancy is extended to identify nonzero constant output failures in large spacecraft active control sensors and actuators, using a set of distributed sensors which do not nominally produce equivalent signals but are related through the structural dynamics of the system. The suboptimal technique uses a Sequential Probability Ratio Test on the residual sequence of a Kalman filter based on a modal structure model, to determine failure of a component based on an assumed failure hypothesis. The specific failure is identified and then the Kalman filter gains are reconfigured for the identified remaining working sensor set. Experimental data using an apparatus whose dynamics are representative of a large spacecraft show the nominal filter performance under failed and unfailed conditions.

Williams, J. P.↗
NASA NTRS1986

Spacecraft charging in the auroral plasma: Progress toward understanding the physical effects involved

The work is presented in four parts. First, main differences between the plasma environments in geostationary orbit and low polar orbit with regard to high-voltage charging situations are reviewed. Next, results are presented from a calculation of secondary-electron escape currents from negatively-charged spacecraft surfaces having various orientations relative to the local magnetic-field direction. It is shown that for finite ranges of combinations of electric and magnetic field directions, secondary-electron escape is completely suppressed and therefore cannot help to discharge the spacecraft. In such circumstances, secondary electrons may travel distances many times their gyroradii before reimpacting, and this may produce greatly increased secondary-electron surface currents. Thirdly, a simple rough estimate of the required conditions for high-voltage auroral-zone charging is developed. The results suggest that for any given spacecraft, surface potentials are likely to depend more strongly on the ratio of ambient flux of high-energy electrons to that of all ions, than on any other environmental parameter. Finally, preliminary results are presented of numerical simulation work directed toward testing this hypothesis. Numerical instabilities encountered in doing this simulation work probably are closely related to physical sensitivities inherent in the physics of the ion wake behind the spacecraft, and especially to beam-like constituents of the ion population in the wake.

Laframboise, J. G.↗
NASA NTRS1986

Protostellar formation in rotating interstellar clouds. V - Nonisothermal collapse and fragmentation

Numerical calculations are presented for rigorous models spanning a four-dimensional parameter space of initial conditions of the three-dimensional collapse of rotating protostellar clouds, encompassing radiative transfer in the Eddington approximation and detailed thermodynamical relations. It is found that protostellar formation may involve a few stages of hierarchical fragmentation terminated by increased thermal pressure in the nonisothermal regime, that high thermal energy clouds remain nearly axisymmetric during the first dynamic collapse phase, and that very slowly rotating clouds can fragment. The presolar nebula was probably formed from a cloud with very little initial rotation.

Boss, Alan R.↗
NASA NTRS1992

Radiative effects of the smoke clouds from the Kuwait oil fires

The radiative effects of the smoke from the Kuwait oil fires were assessed by measuring downwelling and upwelling solar flux, as well as spectral solar extinction beneath, above, and within the smoke plume. Seven radiation flight missions were undertaken between May 16 and June 2, 1991, to characterize the plume between the source region in Kuwait and approximately 200 km south, near Manama, Bahrain. Results are presented from one flight representative of conditions of the composite plume. On May 18, 1991, in a homogeneous, well-mixed region of smoke approximately 100 km downstream of the fires, visible optical depths as high as 2 were measured, at which time transmission to the surface was 8 percent, while 78 percent of the solar radiation was absorbed by the smoke. The calculated instantaneous heating rate inside the plume reached 24 K/d. While these effects are probably typical of those regions in the Persian Gulf area directly covered by the smoke, there is no evidence to suggest significant climatic effects in other regions.

Pilewskie, Peter↗
NASA NTRS1993

Development of a CFD code for casting simulation

Because of high rejection rates for large structural castings (e.g., the Space Shuttle Main Engine Alternate Turbopump Design Program), a reliable casting simulation computer code is very desirable. This code would reduce both the development time and life cycle costs by allowing accurate modeling of the entire casting process. While this code could be used for other types of castings, the most significant reductions of time and cost would probably be realized in complex investment castings, where any reduction in the number of development castings would be of significant benefit. The casting process is conveniently divided into three distinct phases: (1) mold filling, where the melt is poured or forced into the mold cavity; (2) solidification, where the melt undergoes a phase change to the solid state; and (3) cool down, where the solidified part continues to cool to ambient conditions. While these phases may appear to be separate and distinct, temporal overlaps do exist between phases (e.g., local solidification occurring during mold filling), and some phenomenological events are affected by others (e.g., residual stresses depend on solidification and cooling rates). Therefore, a reliable code must accurately model all three phases and the interactions between each. While many codes have been developed (to various stages of complexity) to model the solidification and cool down phases, only a few codes have been developed to model mold filling.

Murph, Jesse E.↗
DOE OSTI2020

MAPPER – A NOVEL CAPABILITY TO SUPPORT NUCLEAR MODEL VALIDATION AND MAPPING OF BIASES AND UNCERTAINTIES

This paper overviews the initial results of a new project at the Oak Ridge National Laboratory -- supported via an internal seed funding program -- focused on the development of a novel computational capability, called MAPPER, to support model validation. The MAPPER development aims to eliminate the need for empirical criteria, such as similarity indices, often employed to identify applicable experiments for given application conditions. To achieve that, MAPPER employs an information-theoretic-based approach, based on the Kullback-Leibler (KL) divergence principle, to combine responses of available or to-be-built experiments with application responses of interest using a training set of samples generated using randomized execution of the experiments and the application high fidelity analysis models. These samples are condensed using reduced order modeling techniques in the form of a joint probability distribution function (PDF) connecting each application response of interest with a new effective experimental response. The initial focus of the MAPPER capability will be to support the confirmatory analysis required for criticality safety analysis of storage facilities which require k-eff biases to be known for safe operation. This paper reports some of the initial results obtained with MAPPER as applied to a set of critical experiments for which existing similarity-based methods have been shown to provide inaccurate estimates of the biases.

Mertyurek, Ugur↗
DOE OSTI2020

High-energy ballistic electrons in low-pressure radio-frequency plasmas

This study demonstrates the presence of a small number of high-energy ballistic electrons (HEBEs) that originate from secondary electrons in low-pressure radio-frequency (rf) plasmas. The kinetic behaviors of the HEBEs are illustrated through electron energy probability functions from the fully kinetic particle-in-cell simulations, showing two wavy high-energy tails and two bifurcations during one rf cycle. Test-particle simulations and a semi-analytical method associated with nonlocal electron kinetics are performed to characterize the HEBE trajectories, which reveal the ballistic nature of the HEBEs and their typical bouncing features between the rf sheaths. Parameter dependence of the HEBEs on the discharge conditions (e.g., gas pressure, gap distance, and rf frequency) are identified, which is relevant to the plasma collisionality. With a pronounced presence of HEBEs, the overall impacts of the secondary electron emission on discharge parameters, such as electron power absorption and ionization rate, are also illustrated.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

The Impact of Operated Window Shading on Visual Comfort, Non-Visual Health, and Energy Demand from Electric Lighting

This paper introduces a simulation-based workflow to assess annual circadian lighting performance, glare risk and energy demand for an array of seated view positions under operated shading and electric lighting conditions. This workflow uses a combination of 9-band and 81-band simulations to represent daylight and electric lighting respectively. Annual daylight-driven calculations rely on a python-based code provided in the LARK simulation engine which was used to run 180-degree high dynamic range (HDR) renderings with 9-bands of spectral resolution. The results reveal the impact of shading systems on equivalent melanopic lux (EML) and daylight glare probability (DGP) over time and the energy demand (kWh) from electric lighting systems to supplement eye-level recommendations from the WELL v2 Building Standard.

Rockcastle, Siobhan↗