SEARCH · Engineering Papers

Results for “component performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

All sources NASA NTRS DOE OSTI

NASA NTRS1992

A 380 GHz SIS receiver using Nb/AlO(x)/Nb junctions for a radioastronomical balloon-borne experiment: PRONAOS

The superheterodyne detection technique used for the spectrometer instrument of the PRONAOS project will provide a very high spectral resolution (delta nu/nu = 10(exp -6)). The most critical components are those located at the front-end of the receiver: their contribution dominates the total noise of the receiver. Therefore, it is important to perform accurate studies for specific components, such as mixers and multipliers working in the submillimeter wave range. Difficulties in generating enough local oscillator (LO) power at high frequencies make SIS mixers very desirable for operation above 300 GHz. The low LO power requirements and the low noise temperature of these mixers are the primary reason for building an SIS receiver. This paper reports the successful fabrication of small (less than or equal to 1 sq micron) Nb/Al-O(x)/Nb junctions and arrays with excellent I-V characteristics and very good reliability, resulting in a low noise receiver performance measured in the 368/380 GHz frequency range.

Febvre, P.↗

DOE OSTI2026

Aluminum addition to AISI 52100 steel: Initial assessment on impact to mechanical properties and tribological performance and pathways for improvement

Here, in the transportation industry, reducing component weight is an effective strategy to improve fuel efficiency and lower emissions. Martensitic AISI 52100 steel is commonly used in drivetrain bearing components due to its high strength and excellent tribological performance. To achieve lightweighting without sacrificing mechanical properties and tribological behavior, this study explored the 52100 steel alloy modified by introducing nominally 5 wt% aluminum. The addition of aluminum led to an approximately 6% density reduction, however, it resulted in reduced hardness, strength and wear resistance, in part due to stabilization of a substantial amount of ferrite, as suggested by microstructural examination. Introducing 0.15 wt% additional carbon reduced the ferrite and demonstrated feasibility of mitigating the mechanical and tribological degradation caused by aluminum. This case study provides fundamental insights into the balance between lightweighting and mechanical/tribological performance for steel alloys, serving as a reference for further development of lightweight bearing steels.

Aluminum addition↗

NASA NTRS1975

Effect of halo component on bar-formation in disk galaxies

Numerical experiments are performed to determine the effect of a fixed halo component of mass on the stability of purely stellar disks. The rotation curve of the fixed halo component corresponds to the Schmidt model of the galaxy. It is found that when the stellar disk contains less than 50% of the total mass, the large-scale bar-making instability is effectively suppressed. For disks containing 50% or more of the total mass, a bar structure quickly forms.

Hohl, F.↗

NASA NTRS2009

Embedded passives emulator FY2003 interim report

The National Aeronautics and Space Administration Electronic Parts and Packaging (NEPP) Program has been evaluating state-of-the-art Embedded Passive Technology for the printed circuit board (PCB) industry for the past several years and has conducted its own testing on embedded passive coupons (resistors and capacitors). This document is a progress report of the work performed through fiscal year 2008 by NASA and the Navy to convert an existing PWB (printed wiring board) design to a design that incorporates embedded passive components. The work is being performed through a memorandum of understanding (MOU) between the NEPP Program (NASA) and the Naval Surface Warfare Center (NSWC) Crane Emerging Critical Interconnect Technology (ECIT) Program. NSWC Crane’s ECIT Program has funding to convert two PCB designs from the military and aerospace industry to a PCB design with embedded passives. ECIT will provide a design team that will take a well characterized design and convert it to an embedded design. They will also provide electrical modeling and layout expertise as well as build the PWB in their facility in Indiana. NEPP, through the Jet Propulsion Laboratory (JPL), will assemble any passives deemed not suitable for embedding and the active components and electrically test the new design to the existing (non-embedded) design

Gerke, David↗

NASA NTRS1991

Thermal verification testing of commercial printed-circuit boards for spaceflight

A method is discussed developed to verify commercial printed-circuit boards for a shuttle orbital flight. The Space Acceleration Measurement System Project used this method first with great success. The test sequence is based on early fault detection, desire to test the final assembly, and integration with other verification testing. A component thermal screening test is performed first to force flaws in design, workmanship, parts, processes, and materials into observable failures. Then temperature definition tests are performed that consist of infrared scanning, thermal vacuum testing, and preliminary thermal operational testing. Only the engineering unit is used for temperature definition testing, but the preliminary thermal operational testing is performed on the flight unit after the temperature range has been defined. In the sequence of testing, vibration testing is performed next, but most vibration failures cannot be detected without subsequent temperature cycling. Finally, final assembly testing is performed to simulate the shuttle flight. An abbreviated thermal screening test is performed as a check after the vibration test, and then a complete thermal operational test is performed. The final assembly test finishes up with a burn-in of 100 hours of trouble-free operation. Verification is successful when all components and final assemblies have passed each test satisfactory. This method was very successful in verifying that commercial printed-circuit boards will survive in the shuttle environment.

Foster, William M., II↗

NASA NTRS1992

Thermal verification testing of commercial printed-circuit boards for spaceflight

A method developed to verify commercial printed-circuit boards for a Shuttle orbital flight is discussed. The test sequence is based on early fault detection, desire to test the final assembly, and integration with other verification testing. A component thermal screening test is performed first to force flaws in design, workmanship, parts, processes, and materials into observable failures. Temperature definition and vibration tests are performed next. Final assembly testing is performed to simulate the Shuttle flight. An abbreviated thermal screening test is performed as a check after the vibration test, and then a complete thermal operational test is performed. The final assembly test finishes up with a burn-in of 100 h of trouble-free operation. Verification is successful when all components and final assemblies have passed each test. This method was very successful in verifying that commercial printed-circuit boards will survive in the Shuttle environment.

Foster, William M., II↗

NASA NTRS1994

A virtual work space for both hands manipulation with coherency between kinesthetic and visual sensation

This paper describes the construction of a virtual work space for tasks performed by two handed manipulation. We intend to provide a virtual environment that encourages users to accomplish tasks as they usually act in a real environment. Our approach uses a three dimensional spatial interface device that allows the user to handle virtual objects by hand and be able to feel some physical properties such as contact, weight, etc. We investigated suitable conditions for constructing our virtual work space by simulating some basic assembly work, a face and fit task. We then selected the conditions under which the subjects felt most comfortable in performing this task and set up our virtual work space. Finally, we verified the possibility of performing more complex tasks in this virtual work space by providing simple virtual models and then let the subjects create new models by assembling these components. The subjects can naturally perform assembly operations and accomplish the task. Our evaluation shows that this virtual work space has the potential to be used for performing tasks that require two-handed manipulation or cooperation between both hands in a natural manner.

Ishii, Masahiro↗

NASA NTRS1995

SSME HPOTP post-test diagnostic system enhancement project

An assessment of engine and component health is routinely made after each test or flight firing of a space shuttle main engine (SSME). Currently, this health assessment is done by teams of engineers who manually review sensor data, performance data, and engine and component operating histories. Based on review of information from these various sources, an evaluation is made as to the health of each component of the SSME and the preparedness of the engine for another test or flight. The objective of this project is to further develop a computer program which automates the analysis of test data from the SSME high-pressure oxidizer turbopump (HPOTP) in order to detect and diagnose anomalies. This program fits into a larger system, the SSME Post-Test Diagnostic System (PTDS), which will eventually be extended to assess the health and status of most SSME components on the basis of test data analysis. The HPOTP module is an expert system, which uses 'rules-of-thumb' obtained from interviews with experts from NASA Marshall Space Flight Center (MSFC) to detect and diagnose anomalies. Analyses of the raw test data are first performed using pattern recognition techniques which result in features such as spikes, shifts, peaks, and drifts being detected and written to a database. The HPOTP module then looks for combination of these features which are indicative of known anomalies, using the rules gathered from the turbomachinery experts. Results of this analysis are then displayed via a graphical user interface which provides ranked lists of anomalies and observations by engine component, along with supporting data plots for each.

Bickmore, Timothy W.↗

DOE OSTI2023

Multiscale Modeling of Corrosion and Oxidation Performance and Their Impact on High-temperature Fatigue of Automotive Exhaust Manifold Components

The persistent need to reducing automobile emissions has led to the wide adoption of turbocharger technology and engine downsizing, which results in a substantial raise in exhaust temperature, reaching as high as 950°C. Therefore, the material selection for exhaust manifolds and turbocharger housings becomes significantly challenging. The successful development of the multiscale models on oxidation and corrosion performance, and their impact on high-temperature fatigue will enable the acceleration of new, high-performance, heat-resistant alloy solutions and the reduction of time and cost in achieving a durable design. In this project, we developed and validated multiscale models that can accurately predict the corrosion and oxidation performance and their impact on high-temperature fatigue of high-temperature automotive exhaust manifold components. The capability of accurately predicting the corrosion/oxidation-fatigue damage can signiﬁcantly reduce the time and cost of achieving a durable design. The models were used to guide the development of new high thermomechanical fatigue (TMF) performance alloys.

Li, Mei↗

DOE OSTI2026

Volumetric Additive Manufacturing of Gradient Composition Glass

Advanced optics, such as lasers or cameras, are currently limited by geometric or compositional restrictions on the silica glass components that act as focusing or refracting lenses. Currently, these glass components must be made of one homogenous material in a range of shapes and sizes limited by a few specialized vendors. However, additional flexibility and customization of these optical components could significantly improve the performance of these devices and expand the design space available to optics engineers, as would the capability to locally change the optical properties of these glass components by changing the composition of the glass as a function of location. To this end, we have developed a method to print and process gradient composition glass, using volumetric additive manufacturing (VAM) and direct ink writing (DIW), on-site at Lawrence Livermore National Lab.

36 MATERIALS SCIENCE↗

NASA NTRS1973

The 5-kwe reactor thermoelectric system summary

Design of the 5-kwe reactor thermoelectric system was initiated in February 1972 and extended through the conceptual design phase into the preliminary design phase. Design effort was terminated in January, 1973. This report documents the system and component requirements, design approaches, and performance and design characteristics for the 5-kwe system. Included is summary information on the reactor, radiation shields, power conversion systems, thermoelectric pump, radiator/structure, liquid metal components, and the control system.

Vanosdol, J. H.↗

NASA NTRS1983

Number and placement of control system sensors considering possible failures

A methodology has been presented which is intended to assist the designer of a control system for a large space structure to decide how many sensors should be incorporated in the system and where they should be placed on the structure. This approach is intended to be especially useful in the early stages of the evolution of the system, before a complete control system concept has been defined. This methodology is based on a quantitative measure of the observability of the system for a given set of sensors. The effect of possible component failures during the mission period was incorporated in the measure. The question of sensor placement is then resolved by finding the locations which maximize the performance measure. The number of components to use cannot be determined by optimizing the measure because the observability always improves with increased number of sensors if they are optimally located. However, the improvement in the measure with component number can be determined, and this information can be used along with data on cost, power required, etc., to decide how many sensors to use.

Vandervelde, W. E.↗

NASA NTRS1990

Stanford/NASA-Ames Center of Excellence in model-based human performance

The human operator plays a critical role in many aeronautic and astronautic missions. The Stanford/NASA-Ames Center of Excellence in Model-Based Human Performance (COE) was initiated in 1985 to further our understanding of the performance capabilities and performance limits of the human component of aeronautic and astronautic projects. Support from the COE is devoted to those areas of experimental and theoretical work designed to summarize and explain human performance by developing computable performance models. The ultimate goal is to make these computable models available to other scientists for use in design and evaluation of aeronautic and astronautic instrumentation. Within vision science, two topics have received particular attention. First, researchers did extensive work analyzing the human ability to recognize object color relatively independent of the spectral power distribution of the ambient lighting (color constancy). The COE has supported a number of research papers in this area, as well as the development of a substantial data base of surface reflectance functions, ambient illumination functions, and an associated software package for rendering and analyzing image data with respect to these spectral functions. Second, the COE supported new empirical studies on the problem of selecting colors for visual display equipment to enhance human performance in discrimination and recognition tasks.

Wandell, Brian A.↗

NASA NTRS2002

Testing Facility Uncertainty Analyses for RBCC Systems Testing

The Rocket Based Combined Cycle (RBCC) engine is expected to evolve based upon past combined-cycle propulsion test experience/data and new extensive test data. Currently, it is envisioned that a portion of the component and system testing will be pursued at NASA Stennis Space Center (SSC). To realize the greatest benefit of the test data, uncertainty analyses are being performed on the relevant RBCC components and systems to be tested at NASA SSC to ascertain the needed measurement requirements. These studies pertain to the existing E-Complex test stands as well as a new facility, E-4. This paper describes the approach used in the studies and gives examples to demonstrate the approach and the usefulness of the results. Future work will greatly increase the reliability of the test data while minimizing costs by focusing expenditures in the proper areas that are critical to program success and not allowing resources to be wasted in areas that are not significant relative to overall program goals.

Hudson, Susan T.↗

DOE OSTI2021

Incorporating historical data and past analyses for improved tensile property prediction of 9% Cr steel

Data-driven analytical clustering and visualization techniques were applied to the dataset of 9% Cr experimental alloy data generated through the eXtremeMAT project. Techniques and results were compared with the resulting clusters obtained through similar analytical techniques on previous and reduced versions of the dataset. The principal components were generated in order to reduce the dimensionality of the complex dataset and to visualize the underlying trends in the data. Partitioning around medoids was performed on the resulting principal components to determine relevant clusters. Domain knowledge labels were further applied to the principal components to compare the labels with the trends identified through the clustering methods. The resulting clusters show the addition of the new data into the dataset, and show where alignment between the domain knowledge labels and partitioning around medoids (PAM) clusters show where the labels are appropriate. The clusters can be used to compare the tensile properties of the alloys, and to reduce the variation in the dataset.

Alloy design, Mechanical Properties, data analysis↗

NASA NTRS2005

Coping with Trial-to-Trial Variability of Event Related Signals: A Bayesian Inference Approach

In electro-neurophysiology, single-trial brain responses to a sensory stimulus or a motor act are commonly assumed to result from the linear superposition of a stereotypic event-related signal (e.g. the event-related potential or ERP) that is invariant across trials and some ongoing brain activity often referred to as noise. To extract the signal, one performs an ensemble average of the brain responses over many identical trials to attenuate the noise. To date, h s simple signal-plus-noise (SPN) model has been the dominant approach in cognitive neuroscience. Mounting empirical evidence has shown that the assumptions underlying this model may be overly simplistic. More realistic models have been proposed that account for the trial-to-trial variability of the event-related signal as well as the possibility of multiple differentially varying components within a given ERP waveform. The variable-signal-plus-noise (VSPN) model, which has been demonstrated to provide the foundation for separation and characterization of multiple differentially varying components, has the potential to provide a rich source of information for questions related to neural functions that complement the SPN model. Thus, being able to estimate the amplitude and latency of each ERP component on a trial-by-trial basis provides a critical link between the perceived benefits of the VSPN model and its many concrete applications. In this paper we describe a Bayesian approach to deal with this issue and the resulting strategy is referred to as the differentially Variable Component Analysis (dVCA). We compare the performance of dVCA on simulated data with Independent Component Analysis (ICA) and analyze neurobiological recordings from monkeys performing cognitive tasks.

Ding, Mingzhou↗

NASA NTRS1974

Applications Technology Satellite ATS-6 in orbit checkout report

The activities of the ATS-6 spacecraft for the checkout period of approximately four weeks beginning May 30, 1974 are described, along with the results of a performance evaluation of its subsystems and components. The following specific items are discussed: (1) subsystem requirements/specifications and in-orbit performance summary; (2) flight chronology; (3) spacecraft description; (4) structural/deployment subsystems; (5) electrical power subsystem; (6) thermal control subsystem; (7) telemetry and command subsystems; (8) attitude control subsystem; (9) spacecraft propulsion subsystem; (10) communication subsystem; and (12) experiment subsystem.

Moore, W.↗

NASA NTRS1984

Steam bottoming cycle for an adiabatic diesel engine

Steam bottoming cycles using adiabatic diesel engine exhaust heat which projected substantial performance and economic benefits for long haul trucks were studied. Steam cycle and system component variables, system cost, size and performance were analyzed. An 811 K/6.90 MPa state of the art reciprocating expander steam system with a monotube boiler and radiator core condenser was selected for preliminary design. The costs of the diesel with bottoming system (TC/B) and a NASA specified turbocompound adiabatic diesel with aftercooling with the same total output were compared, the annual fuel savings less the added maintenance cost was determined to cover the increase initial cost of the TC/B system in a payback period of 2.3 years. Steam bottoming system freeze protection strategies were developed, technological advances required for improved system reliability are considered and the cost and performance of advanced systes are evaluated.

Poulin, E.↗