Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “cathodes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Cluster Expansion Analysis of Atomic Order in Li-Ion Battery Cathode Material LiCo y Ni 1-y O 2

A modified cluster-expansion treatment was developed recently to analyze atomic order in LiCo y Ni 1-y O 2 , a model cathode material for Li-ion batteries. In this treatment, referred to as a “spin-atom” cluster expansion, the occupant of a lattice site is identified by its spin state as well as its atomic species. Further, Effective Cluster Interaction (ECI) coefficients are derived from a large training data set (i.e., the set of atomic arrangements for which DFT calculations are performed) which is filtered by an anomaly detection algorithm to eliminate poorly converged DFT calculations. The cluster expansion incorporates Li-Ni (LN) exchange as well as intralayer Co-Ni (CN) exchange. Monte Carlo simulations based on the cluster expansion were applied to the Ni-rich part of the phase diagram. The simulations predict a miscibility gap between y = 0.05 and y = 0.65.

25 ENERGY STORAGE↗
DOE OSTI2020

Fast Charge-Driven Li Plating on Anode and Structural Degradation of Cathode

Enabling fast charging in lithium ion batteries (LIBs) is a key factor to make electric vehicles drive just like gasoline-powered vehicles when the time comes to refuel. However, fast charging to current LIBs (LiNi x Mn y Co 1–z O 2 /graphite) is limited by lithium plating, which is barely reversible and causes LIBs to lose capacity over time. Thus, research to quantify the lithium plating in LIB cells is extremely important in improving our fundamental understanding of lithium plating behavior and enabling fast charging for LIBs. Here, we precisely quantified the amount of fast-charge-driven lithium plating in a coin-cell composed of LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC532)/graphite. We found that the amount of lithium plating gradually increases with the cycle count and reaches 25.59 μmole (26.80 mAh g –1 cathode ) by the 100th cycle. The study also reveals that the NMC532 has lost 19% of its original lithium content after 100 fast-charging cycles; this, correspondingly, causes a lattice volumetric strain of 0.59%.

25 ENERGY STORAGE↗
DOE OSTI2020

Systematic Study of the Cathode Compositional Dependency of Cross-Talk Behavior in Li-Ion Battery

While LiNi x Mn y Co 1-x-y O 2 (NMC) is one of the most widely used cathode materials for lithium-ion batteries (LIBs), the composition of NMC is evolving to Ni-rich NMC to achieve higher lithium capacity that fulfills the constant demand for LIBs with ever-higher energy densities. The change in the composition of NMC affects electrochemical features and electrode cross-talk, which explains the performance change during cycling. Here in this study, we introduce various NMC materials (LiNi 0.5 Mn 0.3 Co 0.2 O 2 , LiNi 0.6 Mn 0.2 Co 0.2 O 2 and LiNi 0.8 Mn 0.1 Co 0.1 O 2 ) to reveal how the NMC composition affects electrode cross-talk. The study reveals that NMC composition strongly affects transition metal dissolution; dissolution of manganese linearly decreases as its stoichiometric ratio in NMC decreases, while dissolution of nickel is only prominent in LiNi 0.8 Mn 0.1 Co 0.1 O 2 . Aged electrolyte samples are characterized with high-performance liquid chromatography, and two electrolyte decomposition species, C 8 H 16 O 5 and C 9 H 18 O 5 , are identified across all samples.

25 ENERGY STORAGE↗
DOE OSTI2021

Modeling Coupled Chemo-Mechanical Behavior of Randomly Oriented NMC811 Polycrystalline Li-Ion Battery Cathodes

This paper develops a three-dimensional, transient, chemo-mechanical model that predicts the performance of single secondary particle Li-ion battery cathodes. The secondary particles are composed of numerous (approximately 60) randomly oriented single-crystal primary particles. The model incorporates concentration-dependent and anisotropic material properties. As much as possible, electrochemical, transport, and structural properties for crystalline NMC811 (Li x Ni 0.8 Mn 0.1 Co 0.1 O 2 ) are taken from prior publications. Weak Van der Waals bonding between primary particles is modeled empirically using a spring analogy, which enables local primary-particle separations (disintegration) and subsequent reattachments. The model fully couples Li diffusion and the mechanical response. Results include predictions of local Li-concentrations and stresses. High stresses are found near grain boundaries, especially when the lattice orientations are greatly misaligned. Particle separations are characterized in terms of a damage parameter. The model is used to predict the effects of design and operating conditions, including charge/discharge rates, cycling scenarios, and particle sizes.

25 ENERGY STORAGE↗
DOE OSTI2021

Mitigation of PtCo/C Cathode Catalyst Degradation via Control of Relative Humidity

Maintaining the high performance of proton-exchange membrane fuel cells (PEMFC) over the course of its lifetime is a key enabling factor for its successful commercialization as a primary power source in zero-emission transportation applications. In this context, it is important to mitigate the degradation of PtCo-alloy based cathode catalysts used for oxygen reduction reaction (ORR). PtCo-alloy catalysts exhibit high activity at beginning-of-life (BOL) which tends to decrease during operation due to loss of electrochemical surface area (ECSA) and dissolution-contamination related effects of the Co-alloying component. Here, we demonstrate the use of relative humidity (RH) of the inlet gases as a controllable parameter to mitigate the degradation of PtCo-alloy catalyst degradation. We employ a catalyst-specific voltage cycling accelerated stress test (AST) durability protocol as a function of inlet RH to degrade PtCo catalysts. A series of in situ electrochemical diagnostics and ex situ characterizations have been carried out to investigate the catalyst layer characteristics at end-of-test (EOT). Our results show that at sub-saturated conditions of durability protocol operation, PtCo catalyst sustains higher EOT H 2 /air performance due to better retention of ECSA and smaller impact of Co 2+ dissolution/contamination.

25 ENERGY STORAGE↗
DOE OSTI2022

To Pave the Way for Large-Scale Electrode Processing of Moisture-Sensitive Ni-Rich Cathodes

High-capacity Ni-rich cathode such as LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) has a great potential to enable high energy lithium-ion batteries (LIBs) for long-range electrical vehicles. However, the utilization of NMC 811 in large-scale application is still challenging. While many published papers on NMC811 focus on materials modification, the moisture sensitivity of NMC811 and its implications in storage and large-scale electrode coating are not well explored, not to mention how to overcome those challenges for industry application. This work discusses the key parameters impacting the rheological properties of NMC811 slurries and their correlations to the properties of dried electrodes. Effective solutions are proposed to address the gelation issue of NMC811 slurry during large-scale coating to hopefully inspire more effective and practical approaches to tackle the grand challenges in electrochemical energy storage.

25 ENERGY STORAGE↗
DOE OSTI2022

Facile Surface Coatings for Performance Improvement of NMC811 Battery Cathode Material

High nickel content layered oxide LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) is a promising cathode material with a high theoretical capacity of 200 mAh g -1 for use in high energy density lithium-ion batteries. However, its surface can easily get passivated by LiOH and Li 2 CO 3 due to its surface residual Li 2 O being reacting with ambient moisture and CO 2 . Herein, NMC811 was treated in a 3.0 M solution of lithium bis(fluorosulfonyl)imide (LiFSI) in dimethyl carbonate (DMC) at 60 °C for 8 h, 16 h and 24 h, respectively, resulting in coating of the NMC811 surface with LiF due to the basic nature of those residual lithium salts that react with LiFSI. The facile treatment of NMC811 in LiFSI/DMC not only improves the cycling stability but also enhances the capacity of the Li/NMC811 cells, mainly because of the thinning of the Li 2 CO 3 layer as suggested by cyclic voltammograms and impedance analyses. This method opens a new avenue for activation of passivated NMC811 particles for practical battery applications.

25 ENERGY STORAGE↗
DOE OSTI2022

Critical Barriers to Successful Implementation of Earth-Abundant, Mn-Rich Cathodes for Vehicle Applications and Beyond: The Effect of Particle Morphology

As the search for improved and next-generation cathodes continues, it is clear that a deeper understanding of synthesis–structure–electrochemical property relationships is of critical importance. The effects of primary and secondary particle morphologies on various transition metal oxides have been studied, but new findings are still being reported. To date, few studies have focused on the effects of particle morphologies on Li- and Mn-rich oxides (>50% Mn) and even fewer studies have focused on the influence over key properties such as electrode-level impedance. In this study, we report the effects of particle morphologies on the area-specific-impedance (ASI) and thermal behavior of Li- and Mn-rich oxides. Samples with a fixed, layered–layered–spinel (LLS), composition were synthesized with differing primary morphologies and tested under standardized, full-cell protocols. The results suggest that smaller primary particle size (i.e., higher surface area) leads to lower overall ASI, a delay in the increasing impedance at low states-of-charge (SOCs), and surprisingly, improved thermal behavior.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Electrochemistry of Praseodymium in Aqueous Solution Using a Liquid Gallium Cathode

We report the electrochemistry of liquid Ga electrodes in aqueous media was examined in the presence of praseodymium acetate (PrOAc) as an alternate path for low temperature reduction of rare earth elements (REE). This study investigated the aqueous electrochemistry of Ga with and without REEs (Pr). Cyclic voltammetry experiments showed that in the presence of PrOAc, an order of magnitude increase in cathodic current was observed for the Ga electrode, compared to that in the absence of Pr. Decrease in the reduction current with the increase of scan rate, with and without Pr, suggests catalytic reactions following electron transfer, which was attributed to the Ga 2 O disproportionation reaction. Chronoamperometric experiments performed in Pr containing solutions formed a precipitate. Over 50% of the Pr ions from the aqueous electrolyte were immobilized in the precipitate; a solid Ga-rich phase. Formation of this precipitate was only possible when Ga oxidation was induced. This condition was achieved by circulation of liquid Ga from the pool via external pump and returned dropwise to the liquid Ga pool. When the collected precipitate was leached in dilute HCl, Pr was released with H 2 evolved as a byproduct, and Ga returned to its initial liquid metallic state. These preliminary results show encouraging new routes that could be applied for the recovery of diluted REE leachates, such as those obtained from magnets, coal fly ash, and ores.

25 ENERGY STORAGE↗
DOE OSTI2023

LT-LiNi 1/3 Mn 1/3 Co 1/3 O 2 : A Partially-Disordered, Composite Rock Salt Cathode Prepared by Flame Spray Pyrolysis for Li-Ion Batteries

A unique composite cathode structure for Li-ion batteries, designated LT-LiNi 1/3 Mn 1/3 Co 1/3 O 2 (or LT-NMC111), has been prepared by flame spray pyrolysis and subsequent annealing between 400 and 650 °C. It is composed predominantly of structurally-integrated and partially-disordered lithiated-spinel and layered components, both of which can be broadly described as partially-disordered rock salt constituents. The paper describes the evolution of the LT-NMC111 structure as a function of the synthesis method, annealing temperature, and electrochemical properties in the context of other recently reported “low-temperature” (LT) materials, such as LT-LiCo 1−x Al x O 2 and LT-LiMn 0.5 Ni 0.5 O 2 or, in spinel notation, LT-Li 2 Co 2–2x Al 2x O 4 and LT-Li 2 MnNiO 4 , respectively.

25 ENERGY STORAGE↗
DOE OSTI2023

Highly-Conductive and Durable SOFC Cathode-Side Contact Based on Reactively-Sintered Mn-Co Spinel

A cathode-side contact layer with well-matched coefficient of thermal expansion is needed to prevent cracking of solid oxide fuel cell stacks from thermal cycling during stack operations. An Mn 1.25 Co 1.75 O 4 (MCO) spinel layer synthesized via reactive sintering with a metal-containing precursor was proposed as a highly conductive and durable contact material. Compared to the interconnect/contact/cathode assemblies with the (La 0.80 Sr 0.20 ) 0.95 MnO 3-x and La(Mn 0.45 Co 0.35 Cu 0.2 )O 3 contacts, the assembly with the MCO contact exhibited the lowest area-specific resistance at 800 °C (8.2 mΩ·cm 2 ) during 2000-h cyclic exposure and was crack-free based on the cross-sectional examination, indicative of the superiority of the spinel contact over the perovskite counterparts.

Electrochemistry↗
DOE OSTI2024

Cathodic Decomposition Electrodes as Standard Reference Electrodes for Molten Salts: Example of the Lithium Eutectic Electrode for the LiCl-KCl Eutectic

Alternatives to the widely-used standard anodic decomposition reference electrodes in molten salts are necessary to enable more easily reproduced thermochemical and electrochemical data in molten salt electrolytes. The class of standard reference electrodes called cathodic decomposition electrodes (CDEs) are easily constructed and can be used to make thermochemical measurements in molten salts more directly compared to anodic decomposition electrodes. The lithium eutectic electrode (LEE) was chosen as a sample test case for validation and was applied to thermochemical measurements of electroactive species in molten LiCl-KCl eutectic. Transient measurements were made to measure the Li + /Li reduction potential at zero current in pure LiCl-KCl eutectic relative to a Li-alloy reference electrode to validate the reference potential of the LEE. Literature-reported electromotive force measurements against Li-alloy reference electrodes were used to generate a relationship between the LEE and the standard chlorine electrode and this relationship was used to evaluate measured and reported formal potential measurements for the LiCl-KCl-GdCl 3 system. This work demonstrates the general framework for defining CDEs for any molten salt system and a method for calibrating external reference electrodes against a CDE standard reference electrode, improving the ease of obtaining thermochemical and electrochemical measurements in any molten salt system.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Mechanistic Insights into Oxygen Reduction Reaction on Metal Cathode Over BaZrO 3 -Based Electrolyte under Moist Atmosphere: Interfacial Interactions and Reaction Pathways

The oxygen reduction reaction (ORR) is a critical process that often governs the overall performance of electrochemical systems such as proton conducting solid oxide fuel cells. Despite its significance, the current understanding about the ORR, especially when it involves H 2 O is still limited. In this study, the proton involved ORR (PI-ORR) on metal cathode (e.g., Pt) over BaZrO 3 (BZO) electrolyte is investigated using density functional theory (DFT) under moist atmosphere. Two scenarios are considered: one at relatively high temperature (900 K) in the presence of oxygen vacancy in BZO substrate and one at relatively low temperature (700 K) without oxygen vacancy. We systematically explored oxygen vacancy effects on adsorption sites and proton transfer pathways, calculated energy profiles and Gibbs free energies for elementary steps along the O 2 dissociated and the O 2 concerted reaction pathways. We also evaluated H 2 O impacts on intermediate oxygen species (*O and *OH) through Ab Initio molecular dynamics. These analyses revealed pathway-dependent reaction mechanisms and hydration effects at triple-phase boundary, advancing fundamental understanding of PI-ORR in metal cathode/Ba-based electrolyte systems for energy applications.

08 - HYDROGEN↗
DOE OSTI2026

A Reflection on the Evolution of Sodium/Metal Chloride (ZEBRA) Batteries and Lithium-Ion Cathode Materials (1975–2025): A Tribute to Johan Coetzer

This narrative summarizes, in retrospect, the enormous and quietly-conducted contribution of Dr Johan Coetzer, a South African scientist and entrepreneur, to the discovery, development and implementation of the high temperature sodium—metal chloride “ZEBRA” battery (Na/β-Al 2 O 3 , NaAlCl 4 /MCl 2 (M = Ni, Fe)). Here, this research activity was initiated in the mid 1970’s at the Council for Scientific and Industrial Research (CSIR) in South Africa and subsequently developed primarily in partnership with the Atomic Energy Research Establishment (AERE, Harwell, UK), Beta R&D (Derby, UK) and Daimler Benz (Germany), before being transferred to industry worldwide for electric vehicle and energy storage applications, albeit at a relatively low production rate. Coetzer’s wide-ranging, innovative and, at times, unconventional scientific approach also laid the foundation for the discovery and implementation of manganese-based spinel and layered metal oxide cathode materials for the Li-ion battery industry.

ZEBRA Battery↗
DOE OSTI2025

Maximizing Calendering Effects Through the Mechanical Pulverization of Co-Free Nickel-Rich Cathodes in Lithium-Ion Cells

Calendering is a technique used to maximize the volumetric energy density of battery electrodes. However, higher amounts of calendering result in increased tortuosity and particle cracking. We propose a novel packing structure of electrode particles to maximize calendering benefits while minimizing particle fracture. Cobalt-free layered oxide cathode LiNi0.92Mn0.04Al0.04O2 (NMA) particles are pulverized through ball-milling and coated with lithium phosphate. Pulverized and pristine NMA are fabricated into “bimodal” electrodes, whereas “unimodal” electrodes consist of only pristine NMA. Each electrode type was made into 30% porosity, 40% porosity, and uncalendered coin cell samples. X-ray diffraction suggests that the unimodal samples suffer from more particle fracture than the bimodal samples when calendered to the same porosity of 30%. Electrochemical impedance spectroscopy suggests that the bimodal electrodes exhibit lower surface film resistance. This is supported by enhanced capacity retention for the bimodal samples after 100 cycles.

25 ENERGY STORAGE↗
DOE OSTI2025

Enhancement of the electrochemical performance of LiFePO 4 cathode material by nanosecond laser annealing

Pulsed laser annealing of LiFePO 4 can improve conductivity by increasing oxygen vacancy-related defect concentration; this approach can improve the current carrying capacity of LIB cathodes from 135 to 145 mAh g −1 under optimized conditions. Since the depth of the laser annealing region is less than 1 µm, the increase is equivalent to a 125% overall improvement in the charge capacity if the entire thickness of the LiFePO 4 region is treated by pulsed laser annealing. Pulsed laser annealing has two primary effects on the atomic structure of LiFePO 4 , namely an increase in anionic vacancy concentration and antisite defect concentration.

25 ENERGY STORAGE↗
DOE OSTI2026

Beam halo formation with different cathode distributions

Beam halo refers to the low-density distribution of particles extending beyond the beam core, and its generation and mitigation are important topics in particle accelerator design. Effective mitigation of beam halo is essential for the cooler design based on Energy Recovery Linac (ERL), which must deliver an electron beam with average beam current of 100 mA and a charge 1 nC per bunch. In the ERL injector and booster linacs, space charge effects are stronger due to relatively low beam energy (6 MeV). Additionally, the longer bunch length of approximately 100 ps in this regime vs the RF period of 5.08 ns makes the formation of beam halos more likely. Therefore, effective collimation of beam halo is critical to maintaining the required beam parameters. To design an effective collimation scheme, several halo distributions were generated at the cathode and used to study halo formation within the injector-merger. This paper presents different halo distributions and halo formation, providing insights on halo collimation strategy.

Accelerator Physics↗
DOE OSTI2020

Cathode Modeling and Diode Performance in a Planar Geometry using Space-charge-limited Emission

Space-charge-limited (SCL) emission parameters are varied to study the performance effects in a planar diode using an electromagnetic particle-in-cell simulation software suite, EMPIRE. Oscillations in the simulations are found and linked to the emission parameters, namely the breakdown threshold, the emission delay time, and the current density ramp time. The oscillations are suggested to be a transverse oscillator due to the perfect magnetic conductor boundary condition in steady-state operation and the formation of a virtual cathode in the diode driven by the SCL boundary condition.

97 MATHEMATICS AND COMPUTING↗