SEARCH · Engineering Papers

Results for “cable”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

All sources NASA NTRS DOE OSTI

NASA NTRS1972

Solar electric propulsion breadboard thrust subsystem test results.

Work providing a firm basis for building an engineering model thrust subsystem (TSS) is described. A 1500-hr functional demonstration test revealed the impact of each element on TSS integration, operation, and future development. The primary conclusions are: accurate and specific definition of interfaces is essential to a timely system integration program. In addition to normal operating requirements, this definition must include requirements for preflight checkout, self-protection of all interfaces, capability expansion, failure modes, maximum input power, interelement power losses, noise and transient sensitivity and production, packaging for vacuum, thermal control, electrical grounding, cabling, mounting, and handling. In any future design, each phase of the TSS operation (startup, throttling, switching, etc.) should be considered in detail to anticipate and account for possible in-flight variations in element characteristics and performance.

Masek, T. D.↗

NASA NTRS1973

A remote test parameter profile display

Multiplexed digital recording system with simple interface between it and standard commercially available oscilloscopes was developed. System included: rapid set-up, minimum input cabling, low cost, display expansion capability, and portability.

Harrold, J. L.↗

NASA NTRS1973

Digital data command bus

Command bus constructed from coaxial cable has short segments of its outer jacket and shield removed and replaced with small ferrite cores carrying multiturn windings connected to decoder. Device reduces number of wire pairs required to communicate command data to systems and subsystems.

Milligan, G. C.↗

NASA NTRS1973

Manufacture and quality control of interconnecting wire harnesses

Four-volume series of documents has been prepared as standard reference. Each volume may be used separately and covers wire and cable preparation as well as harness fabrication and installation. Series should be useful addition to libraries of manufactures of electrical and electronic equipment.

Source record↗

NASA NTRS1973

Variable load indicator

Weighing device measures loads as a function of its elongation. Device is compact, simple, and inexpensive. It does not require presetting and will measure any load from zero to its yield point. Because of its low cost relative to other load indicators such as strain gauges, device can be used as turnbuckle for tensioning straps, rods, or cables where accurate preloading is critical.

Appleberry, W. T.↗

NASA NTRS1973

Emergency-escape device

Relatively simple inexpensive device uses reeled steel cable, is controlled by automotive-type shock absorber, and allows safe descent from burning building. Device is cheap to manufacture and assemble and requires neither skill, special knowledge, or athletic ability to operate. It is reliable and fireproof and can be deployed instantly.

Broussard, P. M.↗

NASA NTRS1974

Means for mapping radiated fields and for measuring differential movement of antenna elements

Null seeking system uses two transponders located at selected points on dish to detect phase-front of received signal. One signal line has continuously variable phase shifter driven by reversible stepmotor. Each of two transponders on dish is a dipole with mixer crystal between elements. Crystal is driven, in turn, by 181.6MHz signal carried by miniature coaxial cable.

Lundy, C. C.↗

NASA NTRS1974

RF shielded connectors

Gap, where cable joins connector housing, is shielded effectively by composite RF shielding made from suitable potting resin material (fumed silica, thixotropic prepolymer composition), conductive coating (silver-filled, flexible, polyurethane resin), and protective jacket (wax coated housing formed around another wax form having contours shaped to match configuration).

Fisher, A.↗

NASA NTRS1972

Satellite networks for education

Satellite based educational networking is discussed with particular attention given to the potential uses of communications satellites to help meet educational needs in the United states. Four major subject areas were covered; (1) characteristics and structure of networks, (2) definition of pressures within educational establishment that provide motivation for various types of networks, (3) examination of current educational networking status for educational radio and television, instructional television fixed services, inter- and intra-state educational communication networks, computer networks, and cable television for education, and (4) identification of possible satellite based educational telecommunication services and three alternatives for implementing educational satellite systems.

Singh, J. P.↗

NASA NTRS1972

Smoke Plume Analysis Using Fan-beam and Single-beam Radiometers

Smoke plume data were taken using the stacks of the Mills Road Steam Plant on Redstone Arsenal, Huntsville, Alabama. The fan-beam unit was placed approximately 235 meters east of the Mills Road Steam Plant, and the single-beam unit was placed approximately 80 meters north of the fan-beam unit. Results of the smoke plume measurements indicate that the smoke plume is a periodic process near the mouth of the smokestack. The usefulness of the system is limited because of inaccurate and cumbersome positioning methods and base line constraints due to cable length. It is recommended that the radiometers be mounted on pedestals which have both azimuth and elevation positions determined by digitally controlled stepper drive motors. It is also recommended that a time multiplex system be used to transmit data from the radiometers to the electronics van.

Dodd, J. L.↗

NASA NTRS1973

Evaluation of an aeroelastic model technique for predicting airplane buffet loads

A wind-tunnel technique which makes use of a dynamically scaled aeroelastic model to predict full-scale airplane buffet loads during buffet boundary penetration is evaluated. A 1/8-scale flutter model of a fighter airplane with remotely controllable variable-sweep wings and trimming surfaces was used for the evaluation. The model was flown on a cable-mount system which permitted high lift forces comparable to those in maneuvering flight. Bending moments and accelerations due to buffet were measured on the flutter model and compared with those measured on the full-scale airplane in an independent flight buffet research study. It is concluded that the technique can provide valuable information on airplane buffet load characteristics not available from any other source except flight test.

Hanson, P. W.↗

NASA NTRS1972

Manufacturing and quality control of FCC harnesses

The Saturn 5 program contractors encountered many technological challenges and problems relative to inter-connecting wiring and cabling during the development stages of the Saturn program. The knowledge gained from solving these problems, plus recently developed state-of-the-art techniques, materials, and processes were documented in a report prepared for NASA/MSFC. The portions of that report which deal with FCC harnesses are presented.

Malohm, W. L.↗

NASA NTRS1972

Transition splices and cost comparison

The development and testing of two designs of transition splices are reported. The design goal was to produce splice terminations that are electrically insulated to withstand the environmental conditions of commercial aircraft and are capable of being repaired and reworked on installed cables with the use of hand tools. In addition, a cost study comparison of FCC vs. RCC is reported. The comparison was made on a basis of 10 aircraft with each vehicle using approximately 100,000 feet of wiring and 2,000 connectors. The results are tabulated for seven different wiring configurations.

Remedios, M. D.↗

NASA NTRS1972

MSFC connector development

NASA flat conductor cable connectors with individually sealed contacts are described. Descriptions of the design, main features, contact spring, connector electrical data, dimensions and weight, FCC termination, and keying system for plug and receptacle are included.

Angele, W.↗

NASA NTRS1972

Advanced wiring technique and hardware application: Airplane and space vehicle

An advanced wiring system is described which achieves the safety/reliability required for present and future airplane and space vehicle applications. Also, present wiring installation techniques and hardware are analyzed to establish existing problem areas. An advanced wiring system employing matrix interconnecting unit, plug to plug trunk bundles (FCC or ribbon cable) is outlined, and an installation study presented. A planned program to develop, lab test and flight test key features of these techniques and hardware as a part of the SST technology follow-on activities is discussed.

Ernst, H. L.↗

NASA NTRS1972

FCC for homewiring

The application of flat conductor cable technology to surface mounted homewiring was investigated. Baseboard concepts, safety aspects, problems, and advantages are discussed.

Hankins, J. D.↗

NASA NTRS1972

FCC for ALSEP (lunar experiment)

The use of FCC in the ALSEP is discussed. Cable requirements, tradeoffs with round wire, design and development problems are described.

Cripps, G.↗

NASA NTRS1973

Stability analysis and trend study of a balloon tethered in a wind, with experimental comparisons

A stability analysis and trend study for a balloon tethered in a steady wind are presented. The linearized, stability-derivative type analysis includes balloon aerodynamics, buoyancy, mass (including apparent mass), and static forces resulting from the tether cable. The analysis has been applied to a balloon 7.64 m in length, and the results are compared with those from tow tests of this balloon. This comparison shows that the analysis gives reasonable predictions for the damping, frequencies, modes of motion, and stability boundaries exhibited by the balloon. A trend study for the 7.64-m balloon was made to illustrate how the stability boundaries are affected by changes in individual stability parameters. The trends indicated in this study may also be applicable to many other tethered-balloon systems.

Redd, L. T.↗