Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “boundary effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

Transition Delay in Hypersonic Boundary Layers via Optimal Perturbations

The effect of nonlinear optimal streaks on disturbance growth in a Mach 6 axisymmetric flow over a 7deg half-angle cone is investigated in an e ort to expand the range of available techniques for transition control. Plane-marching parabolized stability equations are used to characterize the boundary layer instability in the presence of azimuthally periodic streaks. The streaks are observed to stabilize nominally planar Mack mode instabilities, although oblique Mack mode disturbances are destabilized. Experimentally measured transition onset in the absence of any streaks correlates with an amplification factor of N = 6 for the planar Mack modes. For high enough streak amplitudes, the transition threshold of N = 6 is not reached by the Mack mode instabilities within the length of the cone, but subharmonic first mode instabilities, which are destabilized by the presence of the streaks, reach N = 6 near the end of the cone. These results suggest a passive flow control strategy of using micro vortex generators to induce streaks that would delay transition in hypersonic boundary layers.

Boundary layer transition↗
NASA NTRS1978

Studies on the influence on flexural wall deformations on the development of the flow boundary layer

Flexural wave-like deformations can be used to excite boundary layer waves which in turn lead to the onset of turbulence in the boundary layer. The investigations were performed with flow velocities between 5 m/s and 40 m/s. With four different flexural wave transmissions a frequency range from 0.2 kc/s to 1.5 kc/s and a phase velocity range from 3.5 m/s to 12 m/s was covered. The excitation of boundary layer waves becomes most effective if the phase velocity of the flexural wave coincides with the phase velocity region of unstable boundary layer waves.

Schilz, W.↗
NASA NTRS1993

Shell stability analysis in a computer aided engineering (CAE) environment

The development of 'DISDECO', the Delft Interactive Shell DEsign COde is described. The purpose of this project is to make the accumulated theoretical, numerical and practical knowledge of the last 25 years or so readily accessible to users interested in the analysis of buckling sensitive structures. With this open ended, hierarchical, interactive computer code the user can access from his workstation successively programs of increasing complexity. The computational modules currently operational in DISDECO provide the prospective user with facilities to calculate the critical buckling loads of stiffened anisotropic shells under combined loading, to investigate the effects the various types of boundary conditions will have on the critical load, and to get a complete picture of the degrading effects the different shapes of possible initial imperfections might cause, all in one interactive session. Once a design is finalized, its collapse load can be verified by running a large refined model remotely from behind the workstation with one of the current generation 2-dimensional codes, with advanced capabilities to handle both geometric and material nonlinearities.

Arbocz, J.↗
NASA NTRS1997

Application of PML Absorbing Boundary Conditions to the Benchmark Problems of Computational Aeroacoustics

Accurate numerical non-reflecting boundary conditions are important in all the proposed benchmark problems of the Second Workshop. Recently, a new absorbing boundary condition has been developed using Perfectly Matched Layer (PML) equations for the Euler equations. In this approach, a region with a width of a few grid points is introduced adjacent to the non-reflecting boundaries. In the added region, Perfectly Matched Layer equations are constructed and applied so that the out-going waves are absorbed inside the layer with little reflection to the interior domain. It will be demonstrated in the present paper that the proposed absorbing boundary condition is quite general and versatile, applicable to radiation boundaries as well as inflow and outflow boundaries. It is also easy to implement. The emphasis of the paper will be on the application of the PML absorbing boundary condition to problems in Categories 1, 2, and 3. In Category 1, solutions of problems 1 and 2 are presented. Both problems are solved using a multi-domain polar grid system. Perfectly Matched Layer equations for a circular boundary are constructed and their effectiveness assessed. In Category 2, solutions of problem 2 are presented. Here, in addition to the radiation boundary conditions at the far field in the axisymmetric coordinate system, the inflow boundary condition at the duct inlet is also dealt with using the proposed Perfectly Match Layer equations. At the inlet, a PML domain is introduced in which the incident duct mode is simulated while the waves reflected from the open end of the duct are absorbed at the same time. In Category 3, solutions of all three problems are presented. Again, the PML absorbing boundary condition is used at the inflow boundary so that the incoming vorticity wave is simulated while the outgoing acoustic waves are absorbed with very little numerical reflection. All the problems are solved using central difference schemes for spatial discretizations and the optimized Low-Dissipation and Low-Dispersion Runge-Kutta scheme for the time integration. Issues of numerical accuracy and efficiency are also addressed.

Hu, Fang Q.↗
NASA NTRS1952

Experimental Study of the Effects of Finite Surface Disturbances and Angle of Attack on the Laminar Boundary Layer of an NACA 64A010 Airfoil with Area Suction

A Langley low-turbulence wind-tunnel investigation of a porous NACA 64A010 airfoil section has been made to determine the effectiveness of area suction in maintaining full-chord laminar flow behind finite disturbances and at angles of attacks other than 0 degrees. Aero suction resulted in only a small increase in the size of a finite disturbance required to cause premature boundary-layer transition as compared with that for the airfoil without suction. Combined wake and suction drags lower than the drag of the plain airfoil were obtained through a range of low lift coefficient by the use of area suction.

FLOW, LAMINAR↗
DOE OSTI2023

Observational Investigation of the Effect of Turbulence on Microphysics and Precipitation in Warm Marine Boundary Layer Clouds

Abstract Turbulence is omnipresent in the marine boundary layer (MBL) and several mechanisms have been proposed regarding its role on MBL cloud microphysics. In particular, past modeling studies suggested that increasing turbulence broaden the droplet size distribution (DSD) and leads to precipitation initiation, this suggested relationship has not been evaluated yet using long‐term observations. Here, comprehensive retrievals from long‐term ground‐based observations are used to explore the impact of turbulence on microphysics and precipitation in drizzling MBL clouds. Our analysis supports that broader DSD and larger droplets are observed with strong turbulence, but interestingly, the precipitation is reduced instead of being enhanced. This suppression mechanism is mainly due to the entrainment and mixing process in which the entrained dry air evaporates cloud water. This study provides observational evidence to show the complex effect of turbulence on MBL cloud properties and implies the potential influence of turbulence on the clouds lifetime.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Evaluation and mitigation of trace 210Pb contamination on copper surfaces

Clean materials are required to construct and operate many low-background physics experiments. High-purity copper has found broad use because of its physical properties and availability. In this paper, we describe methods to assay and mitigate Pb-210 contamination on copper surfaces, such as from exposure to environmental radon or coming from bulk impurities. We evaluated the efficacy of wet etching on commercial samples and observed that Po-210 contamination from the copper bulk does not readily pass into solution. During the etch, the polonium appears to trap at the copper-etchant boundary, such that it is effectively concentrated at the copper surface. We observed a different behavior for Pb-210; high-sensitivity measurements of the alpha emissivity versus time indicate the lowest level of Pb-210 contamination ever reported for a commercial copper surface: 0 +/- 12 nBq/cm2 (1-sigma). Additionally, we have demonstrated the effectiveness of mitigating trace Pb-210 and Po-210 surface backgrounds using custom, high-purity electroplating techniques. These approaches were evaluated utilizing assays performed with an XIA UltraLo-1800 alpha spectrometer.

radon, copper, copper cleaning, dark matter, Pb-21↗
NASA NTRS1990

Predicting the aeroelastic behavior of a wind-tunnel model using transonic small disturbance theory

The CAP-TSD (Computational Aeroelasticity Program - Transonic Small Disturbance) code, developed at the NASA-Langley Research Center, is applied to the Active Flexible Wing (AFW) wind-tunnel model for prediction of the model's transonic aeroelastic behavior. Static aeroelastic solutions using CAP-TSD are computed. Dynamic (flutter) analyses are then performed as perturbations about the static aeroelastic deformations of the AFW. The accuracy of the static aeroelastic procedure is investigated by comparing analytical results to those from AFW wind-tunnel experiments. Dynamic results are presented in the form of root loci at different Mach numbers for a heavy gas and for air test mediums. The resultant flutter boundaries for both gases, and the effects of viscous damping and angle of attack on the flutter boundary in air, are also presented.

Silva, Walter A.↗
NASA NTRS1982

Experiments on the stability of the flat-plate boundary layer with suction

Experiments have been conducted in the VPI and SU Stability Wind Tunnel on a flat-plate wind-tunnel model equipped with porous suction panels. Detailed hot-wire measurements were conducted in the laminar boundary layer to investigate the stabilizing effects of suction on growing Tollmien-Schlichting waves, which were introduced into the boundary layer using a vibrating ribbon. Special care was taken to minimize external disturbances and to avoid extraneous experimental bias. The measurements, which included mean-flow and disturbance-amplitude profiles across the boundary layer, showed that suction applied through discrete porous strips can be as effective as suction applied continuously over a much longer streamwise length. The measurements also showed that suction is more effective when placed forward, nearer to the region of neutral stability, than when placed in the region of maximum growth rate. These results also provided meaningful comparison with recent theory.

Reynolds, G. A.↗
NASA NTRS1989

Effects of transverse shear on large deflection random response of symmetric composite laminates with mixed boundary conditions

Nonlinear equations of motion of symmetrically laminated anisotropic plates are derived considering von Karman strains and transverse shear effects. Using a single-mode Galerkin procedure, the nonlinear modal equation is obtained. The direct equivalent linearization method is employed for solution of this equation. The effects of transverse shear on large deflection vibration of laminated plates with mixed boundary support conditions under random excitation are studied. Mean-square deflections and mean-square inplane strains are obtained for symmetric graphite-epoxy laminates. Using equilibrium equations and the continuity requirements, the mean-square transverse shear stresses are calculated. The results obtained will be useful in the sonic fatigue design of composite aircraft panels. The analysis is presented in detail for plates with two opposing edges simply supported and the remaining edges clamped.

Prasad, C. B.↗
NASA NTRS1987

Wind-tunnel investigation of a full-scale general aviation airplane equipped with an advanced natural laminar flow wing

An investigation was conducted in the Langley 30- by 60-Foot Wind Tunnel to evaluate the performance, stability, and control characteristics of a full-scale general aviation airplane equipped with an advanced laminar flow wing. The study focused on the effects of natural laminar flow and advanced boundary layer transition on performance, stability, and control, and also on the effects of several wing leading edge modifications on the stall/departure resistance of the configuration. Data were measured over an angle-of-attack range from -6 to 40 deg and an angle-of-sideslip range from -6 to 20 deg. The Reynolds number was varied from 1.4 to 2.4 x 10 to the 6th power based on the mean aerodynamic chord. Additional measurements were made using hot-film and sublimating chemical techniques to determine the condition of the wing boundary layer, and wool tufts were used to study the wing stall characteristics. The investigation showed that large regions of natural laminar flow existed on the wing which would significantly enhance cruise performance. Also, because of the characteristics of the airfoil section, artificially tripping the wing boundary layer to a turbulent condition did not significantly effect the lift, stability, and control characteristics. The addition of a leading-edge droop arrangement was found to increase the stall angle of attack at the wingtips and, therefore, was considered to be effective in improving the stall/departure resistance of the configuration. Also the addition of the droop arrangement resulted in only minor increases in drag.

Murri, Daniel G.↗
NASA NTRS2003

The Effect of Surface Topography on the Nonlinear Dynamics of Rossby Waves

Boussinesq convection in rotating systems attracts a sustained attention of the fluid dynamics community, because it has intricate non-linear dynamics (Cross & Hohenberg 1993) and plays an important role in geophysical and astrophysical applications, such as the motion of the liquid outer core of Earth, the Red Spot in Jupiter, the giant cells in the Sun etc. (Alridge et al. 1990). A fundamental distinction between the real geo- and astrophysical problems and the idealized laboratory studies is that natural systems are inhomogeneous (Alridge et al. 1990). Heterogeneities modulate the flow and influence significantly the dynamics of convective patterns (Alridge et al. 1990; Hide 1971). The effect of modulations on pattern formation and transition to turbulence in Boussinesq convection is far from being completely understood (Cross & Hohenberg 1993; Aranson & Kramer 2002). It is generally accepted that in the liquid outer core of the Earth the transport of the angular momentum and internal heat occurs via thermal Rossby waves (Zhang et al. 2001; Kuang & Bloxham 1999). These waves been visualized in laboratory experiments in rotating liquid-filled spheres and concentric spherical shells (Zhang et al. 2001; Kuang & Bloxham 1999). The basic dynamical features of Rossby waves have been reproduced in a cylindrical annulus, a system much simpler than the spherical ones (Busse & Or 1986; Or & Busse 1987). For convection in a cylindrical annulus, the fluid motion is two-dimensional, and gravity is replaced by a centrifugal force, (Busse & Or 1986; Or & Busse 1987). Hide (1971) has suggested that the momentum and heat transport in the core might be influenced significantly by so-called bumps, which are heterogeneities on the mantle-core boundary. To model the effect of surface topography on the transport of momentum and energy in the liquid outer core of the Earth, Bell & Soward (1996), Herrmann & Busse (1998) and Westerburg & Busse (2001) have studied the nonlinear dynamics of thermal Rossby waves in a cylindrical annulus with azimuthally modulated height.

Abarzhi, S. I.↗
NASA NTRS1993

Surface boundary conditions for the numerical solution of the Euler equations

We consider the implementation of boundary conditions at solid walls in inviscid Euler solutions by upwind, finite-volume methods. We review some current methods for the implementation of surface boundary conditions and examine their behavior for the problem of an oblique shock reflecting off a planar surface. We show the importance of characteristic boundary conditions for this problem and introduce a method of applying the classical flux-difference splitting of Roe as a characteristic boundary condition. Consideration of the equivalent problem of the intersection of two (equal and opposite) oblique shocks was very illuminating on the role of surface boundary conditions for an inviscid flow and led to the introduction of two new boundary-condition procedures, denoted as the symmetry technique and the curvature-corrected symmetry technique. Examples of the effects of the various surface boundary conditions considered are presented for the supersonic blunt body problem and the subcritical compressible flow over a circular cylinder. Dramatic advantages of the curvature-corrected symmetry technique over the other methods are shown, with regard to numerical entropy generation, total pressure loss, drag and grid convergence.

Dadone, A.↗
NASA NTRS1990

Experimental Study of a Three-Dimensional Shear-Driven Turbulent Boundary Layer with Streamwise Adverse Pressure Gradient

The effects of a strong adverse pressure gradient on a three-dimensional turbulent boundary layer are studied in an axisymmetric spinning cylinder geometry. Velocity measurements made with a three-component laser Doppler velocimeter include all three mean flow components, all six Reynolds stress components, and all ten triple-product correlations. Reynolds stress diminishes as the flow becomes three-dimensional. Lower levels of shear stress were seen to persist under adverse pressure gradient conditions. This low level of stress was seen to roughly correlate with the magnitude of cross-flow (relative to free stream flow) for this experiment as well as most of the other experiments in the literature. Variations in pressure gradient do not appear to alter this correlation. For this reason, it is hypothesized that a three-dimensional boundary layer is more prone to separate than a two-dimensional boundary layer, although it could not be directly shown here. None of the computations performed with either a Prandtl mixing length, k-epsilon, or a Launder-Reece-Rodi full Reynolds-stress model were able to predict the reduction in Reynolds stress.

Driver, David M.↗
DOE OSTI2020

Effects of cluster expansion on the locations of phase transition boundary as a first step to quantify uncertainty in first principles statistical mechanics framework

Predicting phase diagrams from first principle calculations eliminates the need of tedious experimental trials and errors. Fully automating first principle phase diagram calculations without any sort of human intervention has been a long daunting task and troubling scientific communities for decades. This grand problem remains not fully resolved, largely due to the vastly high-dimensional parameter space associated with density functional theory, cluster expansion, lattice Monte Carlo, and the substantial uncertainty propagating through a set of complex simulations. As a first step to tackle this grand problem, we reported a first demonstration of how sensitive phase boundary locations can be to various cluster expansion fittings and input DFT training data. To the best knowledge of the authors, this study reported the first ever attempt to quantify uncertainty in first principles statistical mechanics framework. In addition, a semi-automated phase transition detection algorithm has been devised in this paper to deal with the associated statistical errors and uncertainties from Monte Carlo method and its predecessor DFT calculations and cluster expansions. This algorithm has been applied in a classical cluster expansion Mg-Cd binary alloy system to detect phase transitions at various locations of phase diagram using different cluster expansions to demonstrate its predictive power and quantify uncertainties. The results suggested that using Chebyshev basis function shifted the transition locations toward the dilute solid solution phase and expanded the phase stability of concentrated ordered phases to wider composition range. The addition of perturbed defect configurations into training data set lowered the order-disorder transition temperature to be away from true transition temperature, suggesting the transition nature is indeed configurational disorder dominated rather than defect assisted. Finally, we found that the weighting has negligible effect on the transition locations, except for the case of using Chebyshev basis function to fit all non-weighted configurations that can be susceptible to Monte Carlo sampling hysteresis.

36 MATERIALS SCIENCE↗
NASA NTRS2013

Investigation of Materials for Boundary Layer Control in a Supersonic Wind Tunnel

During operation of the NASA Glenn Research Center 15- by 15-Centimeter Supersonic Wind Tunnel (SWT), a significant, undesirable corner flow separation is created by the three-dimensional interaction of the wall and floor boundary layers in the tunnel corners following an oblique-shock/ boundary-layer interaction. A method to minimize this effect was conceived by connecting the wall and floor boundary layers with a radius of curvature in the corners. The results and observations of a trade study to determine the effectiveness of candidate materials for creating the radius of curvature in the SWT are presented. The experiments in the study focus on the formation of corner fillets of four different radii of curvature, 6.35 mm (0.25 in.), 9.525 mm (0.375 in.), 12.7 mm (0.5 in.), and 15.875 mm (0.625 in.), based on the observed boundary layer thickness of 11.43 mm (0.45 in.). Tests were performed on ten candidate materials to determine shrinkage, surface roughness, cure time, ease of application and removal, adhesion, eccentricity, formability, and repeatability. Of the ten materials, the four materials which exhibited characteristics most promising for effective use were the heavy body and regular type dental impression materials, the basic sculpting epoxy, and the polyurethane sealant. Of these, the particular material which was most effective, the heavy body dental impression material, was tested in the SWT in Mach 2 flow, and was observed to satisfy all requirements for use in creating the corner fillets in the upcoming experiments on shock-wave/boundary-layer interaction.

Braafladt, Alexander↗
NASA NTRS1993

Effects of precipitation on the thermodynamic structure of the trade wind boundary layer

A model of the thermodynamic structure of the trade wind boundary layer is formulated to include the parameterization of precipitation in relatively shallow clouds. Although the area-averaged simulated precipitation rates are relatively small (less than 1 mm/day), the inclusion of precipitation has an appreciable effect on the predicted thermodynamic structure. The cloud layer structure simulated with precipitation is warmer, drier, and more stable than that simulated without precipitation. The simulated inversion height is lowered by as much as 60 mbar when precipitation is included.

Albrecht, Bruce A.↗