Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TiP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Recent finite element studies in plasticity and fracture mechanics

The paper reviews recent work on fundamentals of elastic-plastic finite-element analysis and its applications to the mechanics of crack opening and growth in ductile solids. The presentation begins with a precise formulation of incremental equilibrium equations and their finite-element forms in a manner valid for deformations of arbitrary magnitude. Special features of computational procedures are outlined for accuracy in view of the near-incompressibility of elastic-plastic response. Applications to crack mechanics include the analysis of large plastic deformations at a progressively opening crack tip, the determination of J integral values and of limitations to J characterizations of the intensity of the crack tip field, and the determination of crack tip fields in stable crack growth.

Rice, J. R.↗
NASA NTRS1979

Computation of subsonic and transonic flow about lifting rotor blades

An inviscid, nonconservative, three-dimensional potential flow code has been developed for computing the quasi-steady flow about an isolated lifting rotor blade. Calculations from the code were compared with chordwise pressure measurements obtained in a wind tunnel on a nonlifting rotor at transonic tip speeds at advance ratios from 0.40 to 0.55. The overall agreement between theoretical calculations and experiment was good. To illustrate the early capability of the program, the flow about a hypothetical lifting rotor blade having twist, airfoil thickness taper, and a 20 deg sweptback tip was analyzed at azimuthal positions of 60, 90, and 120 deg for an advance ratio of 0.342. A typical run on a CDC 7600 computer required about 5 min for one rotor position at transonic tip speeds.

Arieli, R.↗
NASA NTRS1980

Comparison of calculated and measured model rotor loading and wake geometry

The calculated blade bound circulation and wake geometry are compared with measured results for a model helicopter rotor in hover and forward flight. Hover results are presented for rectangular tip and ogee tip planform blades. The correlation is quite good when the measured wake geometry characteristics are used in the analysis. Available prescribed wake geometry models are found to give fair predictions of the loading, but they do not produce a reasonable prediction of the induced power. Forward flight results are presented for twisted and untwisted blades. Fair correlation between measurements and calculations is found for the bound circulation distribution on the advancing side. The tip vortex geometry in the vicinity of the advancing blade in forward flight was predicted well by the free wake calculation used, although the wake geometry did not have a significant influence on the calculated loading and performance for the cases considered.

Johnson, W.↗
NASA NTRS1980

Three dimensional mean flow and turbulence characteristics of the near wake of a compressor rotor blade

The investigation was carried out using the rotating hot wire technique. Measurements were taken inside the end wall boundary layer to discern the effect of annulus and hub wall boundary layer, secondary flow, and tip leakage on the wake structure. Static pressure gradients across the wake were measured using a static stagnation pressure probe insensitive to flow direction changes. The axial and the tangential velocity defects, the radial component of velocity, and turbulence intensities were found to be very large as compared to the near and far wake regions. The radial velocities in the trailing edge region exhibited characteristics prevalent in a trailing vortex system. Flow near the blade tips found to be highly complex due to interaction of the end wall boundary layers, secondary flows, and tip leakage flow with the wake. The streamwise curvature was found to be appreciable near the blade trailing edge. Flow properties in the trailing edge region are quite different compared to that in the near and far wake regions with respect to their decay characteristics, similarity, etc. Fourier decomposition of the rotor wake revealed that for a normalized wake only the first three coefficients are dominant.

Ravindranath, A.↗
NASA NTRS1980

Comparison of calculated and measured helicopter rotor lateral flapping angles

Calculated and measured values of helicopter rotor flapping angles in forward flight are compared for a model rotor in a wind tunnel and an autogiro in gliding flight. The lateral flapping angles can be accurately predicted when a calculation of the nonuniform wake-induced velocity is used. At low advance ratios, it is also necessary to use a free wake geometry calculation. For the cases considered, the tip vortices in the rotor wake remain very close to the tip-path plane, so the calculated values of the flapping motion are sensitive to the fine details of the wake structure, specifically the viscous core radius of the tip vortices.

Johnson, W.↗
NASA NTRS1979

Path dependence of J in three numerical examples

Three cracked geometries are studied with the aid of a new finite element model. The procedure employs a variable singularity at the crack tip that tracks changes in the material response during the loading process. Two of the problems are tension-loaded center-crack panels and the other is a three-point bend specimen. Results usually agree with other numerical and analytical analyses, except the finding that J is path dependent as a substantial plastic zone develops. Credible J values are obtained near the crack tip and J shows a significant increase as the radius of J path increases over two orders of magnitude. Incremental and deformation theories are identical provided the stresses exhibit proportionality found in the far field stresses but not near the tip.

Karabin, M. E., Jr.↗
NASA NTRS1981

Vibration characteristics of a laser heterodyne spectrometer tunable diode laser system using a mechanical cooler platform

The Langley Research Center redesigned the cooler test bed hardware for the refrigerator for the purpose of isolating the tunable diode laser (TDL) from the cold tip in a laser heterodyne spectrometer system. Deflection in the lateral and vertical directions were managed on the cold tip and on the TDL. Measurements were analyzed over the frequency range of 0.100 Hz. The results show that the TDL responds approximately one order of magnitude less than that of the cold tip. The redesign of the system provided for adequately isolating the TDL for future operation.

Catherines, J. J.↗
NASA NTRS1981

Evidence of imbedded vortices in a three-dimensional shear flow

Vortex phenomena encountered in an investigation of the streamwise development of the three-dimensional wake region behind the tip of a three-dimensional wedge model are reported. Pressure profiles were measured by pitot probes downstream of a tip with a nearly constant surface pressure level and a nearly continuous surface curvature in a blowdown air tunnel operating at Mach 6. Rather than the simple three-dimensional quasi-parallel shear flow expected, the measurements indicated the presence of a flow with large deficits in longitudinal pitot pressure, which are usually associated with the core region of quasi-steady longitudinal vortices. Vapor screen flow visualizations also support the presence of longitudinal vortices located primarily in the tip region and evidently forming in the vicinity of the wake neck. An increase in overall wake thickness by 100% is also observed. The origin of the vortices as quasi-steady Taylor-Gortler vortices generated in the concavely curved shear layer near the wake neck is considered. It is pointed out that the existence of longitudinal vortexes suggests that three-dimensional turbulence modeling may be much more difficult than previously supposed.

Morrisette, E. L.↗
NASA NTRS1949

Vibration and icing investigation of CAA type V-109 very-high-frequency aircraft antenna

Vibration and icing determinations on a CAA type V-109 very-high-frequency aircraft antenna were conducted in the NACA Lewis icing research tunnel. The antenna is an omnidirectional-range unit that consists of two aluminum elements mounted in a streamline plastic head forming a V in plan view with an apex angle of 80°. Vibration determinations during a nonicing experiment produced element-tip total amplitude of approximately 1/4 inch at a tunnel-air velocity of 300 miles per hour. During the icing investigation, a total amplitude as great as 7 inches was observed at the antenna-element tips with tunnel-air velocities greater than 160 miles per hour and a tunnel-air temperature of 20° F. At the higher tunnel-air temperatures, which produced a heavier and more severe ice accretion, the damping effect of the ice reduced the element-tip amplitudes over the entire range of tunnel-air velocities to a maximum of 1/4 inch at a tunnel-air velocity of 300 miles per hour.

William H Gowan, Jr↗
NASA NTRS1981

JT8D high pressure compressor performance improvement

An improved performance high pressure compressor with potential application to all models of the JT8D engine was designed. The concept consisted of a trenched abradable rubstrip which mates with the blade tips for each of the even rotor stages. This feature allows tip clearances to be set so blade tips run at or near the optimum radius relative to the flowpath wall, without the danger of damaging the blades during transients and maneuvers. The improved compressor demonstrated thrust specific fuel consumption and exhaust gas temperature improvements of 1.0 percent and at least 10 C over the takeoff and climb power range at sea level static conditions, compared to a bill-of-material high pressure compressor. Surge margin also improved 4 percentage points over the high power operating range. A thrust specific fuel consumption improvement of 0.7 percent at typical cruise conditions was calculated based on the sea level test results.

Gaffin, W. O.↗
NASA NTRS1981

Experimental and analytical studies of a model helicopter rotor in hover

A benchmark test to aid the development of various rotor performance codes was conducted. Simultaneous blade pressure measurements and tip vortex surveys were made for a wide range of tip Mach numbers including the transonic flow regime. The measured tip vortex strength and geometry permit effective blade loading predictions when used as input to a prescribed wake lifting surface code. It is also shown that with proper inflow and boundary layer modeling, the supercritical flow regime can be accurately predicted.

Caradonna, F. X.↗
NASA NTRS1981

Hover tests of a model H-force rotor

The potential of using tip vanes at the ends of helicopter rotor blades to obtain a controllable H-force is considered. The addition of vanes placed perpendicular to the blade tips can be used to obtain an inplane force. By varying the angle of the vanes, a radial force can be created which can be controllable in azimuth position. Such a force could be used to provide translational motion of the rotor and aircraft without the requirement for rotor tilting. In addition, an H-force generated at high flight speed could be used as a propulsive force in a matter similar to a propeller. The force generated by the vanes could also affect the aircraft's stability characteristics. The H-force could also modify rotor performance in hovering since they could be thought to act as a virtual shroud. Tests were run with a model rotor which has a 6 foot diameter with a 3 inch chord blade. Test data are presented on the effects of various tip-vane configurations on the hovering figure of merit. The extreme sensitivity of the performance to vane arrangement is shown.

Velkoff, H. R.↗
NASA NTRS1980

Forward velocity effects on fan noise and the suppression characteristics of advanced inlets as measured in the NASA-Ames 40 by 80 foot wind tunnel

Forward velocity effects on the forward radiated fan noise and on the suppression characteristics of three advanced inlets relative to a baseline cylindrical inlet were measured in the NASA Ames Research Center 40 x 80 foot Wind Tunnel. A modified JT15D turbofan engine in a quiet nacelle was the source of fan noise; the advanced inlets were a Conventional Takeoff/Landing (CTOL) hybrid inlet, a Short Takeoff/Landing (STOL) hybrid inlet, and a treated deflector inlet. Also measured were the static to flight effects on the fan noise of canting the baseline inlet 4 deg downward to simulate typical wing mounted turbofan engines. The CTOL hybrid inlet suppressed the high tip speed fan noise as much as 18 PNdB on a 61 m (200 ft) sideline scaled to a CF6 size engine while the STOL hybrid inlet suppressed the low tip speed fan noise as much as 13 PNdB on a 61 m (200 ft) sideline scaled to a OCSEE size engine. The deflector inlet suppressed the high tip speed fan noise as much as 13 PNdB at 61 m (200 ft) overhead scaled to a CF6 size engine. No significant changes in fan noise suppression for the CTOL and STOL hybrid inlets occurred for forward velocity changes above 21 m/s (68 ft/s) or for angle of attack changes up to 15 deg. However, changes in both forward velocity and angle of attack changed the deflector inlet noise unpredictably due to the asymmetry of the inlet flow field into the fan.

Moore, M. T.↗
NASA NTRS1982

On a study of the /Delta T/c and C/asterisk/ integrals for fracture analysis under non-steady creep

Applications of a vector quantity, path-independent integral which has an energy interpretation to the characterization of crack-tip fields in the range from fast to slow crack propagation are examined. The crack tip characterization parameter is defined in terms of a conservation integral for an area around the crack tip in a two-dimensional cracked body. The actual physical interpretation of the parameter is shown to be the difference in crack lengths displayed by two identical bodies which have equal load histories. A steady-state value is obtained for the parameter for cases of steady-state creep and is shown to be related to the standard path-independent integral for macroscopic self-similar crack growth under mode I conditions. A finite element model is developed for viscoplastic material models, using an initial strain approach with steps in a size employed in tangent stiffness methods.

Stonesifer, R. B.↗
NASA NTRS1984

Digital Soldering-Iron Tester

Instrument reads tip temperature and contact potential in seconds. Tinned soldering tip touched to temperature sensitive button for 4 seconds and to voltage probe for 1 to 3 seconds. Tip temperature and voltage appear on digital displays. Instrument quickly gives assurance conditions are correct for reliable soldering.

Buggle, R. N.↗
NASA NTRS1983

Effect of modifications of aerodynamic characteristics of a single-stage-to-orbit vehicle at Mach 5.9

Hypersonic stability, control, and performance characteristics were determined on a single-stage-to-orbit vehicle based on control-configured stability concepts. The configuration (0.006-scale model) had a large body with a small 50 deg swept wing. Two vertical-fin arrangements were investigated which consisted of a large center-line vertical tail and small wing-tip fins. The wing-tip fins had movable surfaces called controllers which could be deflected outward. Longitudinal and lateral directional characteristics were obtained over an angle-of-attack rage from 0 deg to 40 deg. The effects of tip-fin controller deflection on roll- and yaw-control characteristics at a sideslip angle of 0 deg were obtained. This investigation was conducted in the Langley 20 Inch Mach 6 Tunnel.

Bernot, P. T.↗
NASA NTRS1983

Selected advanced aerodynamics and active controls technology concepts development on a derivative B-747 aircraft

Analytical design and wind tunnel test evaluations covering the feasibility of applying wing tip extensions, winglets, and active control wing had alleviation to the model B747 are described. Aerodynamic improvement offered by wing tip extension and winglet individually, and the combined aerodynamic and weight improvements when wing load alleviation is combined with the tip extension or the winglet are evaluated. Results are presented in the form of incremental effects on weight mission range, fuel usage, cost, and airline operating economics.

Source record↗
NASA NTRS1983

Lean Limit Phenomena

The influence of stretch and preferential diffusion on premixed flame extinction and stability was investigated via two model flame configurations, namely the stagnation flame and the bunsen flame. Using a counterflow burner and a stagnation flow burner with a water-cooled wall, the effect of downstream heat loss on the extinction of a stretched premixed flame investigated for lean and rich propane/air and methane/air mixtures. It was demonstrated that extinction by stretch alone is possible only when the deficient reactant is the less mobile one. When it is the more mobile one, downstream heat loss or incomplete reaction is also needed to achieve extinction. The local extinction of bunsen flame tips and edges of hydrocarbon/air premixtures was investigated using a variety of burners. Results show that, while for both rich propane/air and butane/air mixtures tip opening occurs at a constant fuel equivalence ratio of 1.44 and is therefore independent of the intensity, uniformity, and configuration of the approach flow, for rich methane/air flames burning is intensified at the tip and therefore opening is not possible.

Law, C. K.↗