Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “System Operations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Assessment Study of Small Space Debris Removal by Laser Satellites

Space debris in Earth orbit poses significant danger to satellites, humans in space, and future space exploration activities. In particular, the increasing number of unidentifiable objects, smaller than 10 cm, presents a serious hazard. Numerous technologies have been studied for removing unwanted objects in space. Our approach uses a short wavelength laser stationed in orbit to vaporize these small objects. This paper discusses the power requirements for space debris removal using lasers. A short wavelength laser pumped directly or indirectly by solar energy can scan, identify, position, and illuminate the target, which will then be vaporized or slow down the orbital speed of debris by laser detonation until it re-enters the atmosphere. The laser-induced plasma plume has a dispersive motion of approximately 105 m/sec with a Lambertian profile in the direction of the incoming beam [1-2]. The resulting fast ejecting jet plume of vaporized material should prevent matter recombination and condensation. If it allows any condensation of vaporized material, the size of condensed material will be no more than a nanoscale level [3]. Lasers for this purpose can be indirectly pumped by power from an array of solar cells or directly pumped by the solar spectrum [4]. The energy required for vaporization and ionization of a 10 cm cube (~ 2700 gm) of aluminum is 87,160 kJ. To remove this amount of aluminum in 3 minutes requires a continuous laser beam power of at least 5.38 MW under the consideration of 9% laser absorption by aluminum [5] and 5% laser pumping efficiency. The power needed for pumping 5.38 MW laser is approximately 108 MW, which can be obtained from a large solar array with 40% efficiency solar cells and a minimal area of 450 meters by 450 meters. This solar array would collect approximately 108 MW. The power required for system operation and maneuvering can be obtained by increasing solar panel size. This feasibility assessment covers roughly the power requirement, laser system, and a potential operational scenario.

Choi, Sang H.↗
NASA NTRSDate not supplied

Towards Autonomous Lunar Resource Excavation via Reinforcement Learning

To continue on a sustainable and flexible path, NASA needs to address the challenge of collecting and moving large amounts of regolith at the destination. NASA’s Regolith Advanced Surface Systems Operations Robot (RASSOR) is principally designed to mine and deliver regolith for In-Situ Resource Utilization (ISRU) processing. RASSOR’s design enables it to efficiently collect and deposit regolith, return collected material for processing, and myriad related ISRU activities. To reliably perform these operations on the lunar surface, RASSOR software and sensory systems need to be robust and maximize the information extracted from a reduced sensor payload. Herein, we present preliminary findings from the Intelligent Capabilities Enhanced RASSOR project. We created reduced-order simulation environments to develop autonomous trenching controllers via reinforcement learning and prototype state estimation architectures. The goal of reinforcement learning is for an agent to learn a policy (task strategy) through interactions with an environment. When the agent performs an action, a change occurs in environment state and a numerical reward is received which informs the agent whether the action performed was good or not. Since reinforcement learning algorithms learn through trial-and-error, a simulation is a desirable first environment for development and learning. We developed two simulations, the first is a 2D excavation simulation developed to facilitate parameter selection, and a 3D simulation developed using a game physics engine, to simulate simplified soil interactions and increase the fidelity of the dynamic models of the robotic agents. The development of this 3D simulation has enabled the training of additional sensing capabilities and research both at the granular mechanics and operations levels. We experimented with various virtual sensor payloads to identify a combination that enabled efficient excavation operation and learning. Our reward function is based on how much material is excavated per step. A penalty is also received for leaving the dig site and to smooth the acceleration of the drum arms. We implemented pseudo time-of-flight sensors to report distance from each drum to ground and the height above ground which was found to be more efficient than existing solutions. Our findings suggest that reinforcement learning for autonomous operations has learned viable trenching strategies within 3000 training episodes in our simplified 2D environment and helped identify desirable sensing capabilities, arrangements, and considerations such as the positioning of time-of-flight sensors. Future work includes expanding our simulation to more complex environments and scenarios, and transfer learning from simulation to RASSOR 2.0 hardware for deployment in the Regolith Test Bin at NASA's Kennedy Space Center.

rassor↗
NASA NTRS1993

An operations concept methodology to achieve low-cost mission operations

Historically, the Mission Operations System (MOS) for a space mission has been designed last because it is needed last. This has usually meant that the ground system must adjust to the flight vehicle design, sometimes at a significant cost. As newer missions have increasingly longer flight operations lifetimes, the MOS becomes proportionally more difficult and more resource-consuming. We can no longer afford to design the MOS last. The MOS concept may well drive the spacecraft, instrument, and mission designs, as well as the ground system. A method to help avoid these difficulties, responding to the changing nature of mission operations is presented. Proper development and use of an Operations Concept document results in a combined flight and ground system design yielding enhanced operability and producing increased flexibility for less cost.

Ledbetter, Kenneth W.↗
DOE OSTI2024

Robust VAR Capability Curve of DER with Uncertain Renewable Generation

Active distribution system with high penetration of inverter based distributed energy resources(DER), can be utilized for var-related ancillary services at the transmission side interface. In order to utilize the DER flexibility, transmission system operator must be presented the aggregated DER flexibility of distribution system. However, the uncertainty in renewable generation, questions the credibility of aggregated capability curve in practice. In this paper, we incorporate the uncertainty into aggregation process to develop capability curve while preserving the real physics (unbalance and lossy nature) of distribution system. The Resulting capability curve with the associated probability can be harnessed by the TSO for decision making for both planning and operation.

Kar, Aditya Shankar↗
DOE OSTI2024

Revealing Decision Conservativeness Through Inverse Distributionally Robust Optimization

This paper introduces Inverse Distributionally Robust Optimization (I-DRO) as a method to infer the conservativeness level of a decision-maker, represented by the size of a Wasserstein metric-based ambiguity set, from the optimal decisions made using Forward Distributionally Robust Optimization (F-DRO). By leveraging the Karush-Kuhn-Tucker (KKT) conditions of the convex F-DRO model, we formulate I-DRO as a bi-linear program, which can be solved using off-the-shelf optimization solvers. Additionally, this formulation exhibits several advantageous properties. We demonstrate that I-DRO not only guarantees the existence and uniqueness of an optimal solution but also establishes the necessary and sufficient conditions for this optimal solution to accurately match the actual conservativeness level in F-DRO. Furthermore, we identify three extreme scenarios that may impact I-DRO effectiveness. Our case study applies F-DRO for power system scheduling under uncertainty and employs I-DRO to recover the conservativeness level of system operators. Numerical experiments based on an IEEE 5-bus system and a realistic NYISO 11-zone system demonstrate I-DRO performance in both normal and extreme scenarios. An extended version of this paper with additional analyses is available at li2024revealing.

distributionally robust optimization↗
DOE OSTI2026

Measurement Adequacy for Monitoring Data Center Oscillations

Artificial intelligence (AI) training data centers with periodic load profiles can induce sustained grid oscillations across a wide frequency range, making accurate monitoring essential for reliable power system operation. This report evaluates the adequacy of existing measurement systems for monitoring such oscillations, focusing on phasor measurement units (PMUs) and point-on-wave (POW) measurement systems. The analysis shows that while PMUs are highly effective for monitoring low-frequency electromechanical oscillations, they have inherent limitations in accurately representing higher-frequency oscillations due to constraints imposed by reporting rates and the bandwidth of phasor estimation filters. Even when configured with higher reporting rates, the filtering inherent in the phasor estimation process can significantly attenuate oscillation magnitudes, potentially leading to underestimation of oscillatory behavior. This has important implications for compliance and performance monitoring of large loads. To address the limitations associated with PMU-based monitoring, the report examines the use of high-resolution POW measurements, which can capture oscillations across a broader frequency range. However, continuous POW monitoring introduces practical challenges related to large data volumes, communication bandwidth, and real-time data processing. For this reason, the report also discusses emerging approaches that use POW measurements as a complementary capability alongside PMUs to improve observability of oscillations from large data center loads.

47 OTHER INSTRUMENTATION↗
NASA NTRS1964

Investigation and study of a multi-aperture antenna system final report, 1 jan. - 1 apr. 1964

This investigation was concerned with a multiple aperture adaptive antenna system for application to receiving telemetered data from remote space vehicles or satellites. The primary criterion for determining the feasibility of such a system has been economic considerations, but of necessity many physical constraints imposed on both a single antenna and a multiple aperture system have been evaluated. These include such factors as acquisition and combining of signals, look angle, shadowing, propagation influences system spatial bandwidth, collimation, interference, doppler effects, reliability, and noise. Specific conclusions have been made for a system operating at a frequency of 2 Gc, but the system model adopted allows quick evaluation at other frequencies. At a frequency of 2Gc, the crossover point between a single antenna or a multiple aperture configuration occurs for an 85 foot reflector. However this transition region is not critical. For lunar range communications a single antenna appears to be the most economical, whereas at interplanetary ranges aperture equivalents of around 400 feet are required and achieved by arraying eight 142 foot antennas.

TELEMETRY↗
NASA NTRS1972

Apollo experience report: Lunar module communications system

The development of the lunar module communications system is traced from the initial concept to the operational system used on manned lunar missions. The problems encountered during the development, the corrective actions taken, and recommendations for similar equipment in future programs are included. The system was designed to provide communications between the lunar module and the manned space flight network, between the lunar module and the command and service module, and between the lunar module and the extravehicular crewmen. The system provided the equipment necessary for voice, telemetry, and television communications; ranging information; and various communications links.

Dietz, R. H.↗
NASA NTRS1973

Design and fabrication of an augmentor wing model for acoustic tests

The design and fabrication of a full-scale section of an augmentor wing to be used for acoustic testing at the Lewis Research Center are discussed. This hardware will be used primarily to investigate scaling effects of acoustic data obtained during the Boeing-run model tests. Typical model test data is shown in the report, together with predictions on both performance and acoustics that can be expected from the full-scale section to be built. Areas covered include: the aerodynamic and acoustic criteria of the flap system and nozzles, detailed discussion of the hardware, test system operation procedure, and stress analysis of the entire test system.

Jackson, J.↗
NASA NTRS1976

Investigation of selected disk systems

The large disk systems offered by IBM, UNIVAC, Digital Equipment Corporation, and Data General were examined. In particular, these disk systems were analyzed in terms of how well available operating systems take advantage of the respective disk controller's transfer rates, and to what degree all available data for optimizing disk usage is effectively employed. In the course of this analysis, generic functions and components of disk systems were defined and the capabilities of the surveyed disk system were investigated.

Source record↗
NASA NTRS1977

Annual Symposium on Machine Processing of Remotely Sensed Data, 4th, Purdue University, West Lafayette, Ind., June 21-23, 1977, Proceedings

Papers are presented on a variety of techniques for the machine processing of remotely sensed data. Consideration is given to preprocessing methods such as the correction of Landsat data for the effects of haze, sun angle, and reflectance and to the maximum likelihood estimation of signature transformation algorithm. Several applications of machine processing to agriculture are identified. Various types of processing systems are discussed such as ground-data processing/support systems for sensor systems and the transfer of remotely sensed data to operational systems. The application of machine processing to hydrology, geology, and land-use mapping is outlined. Data analysis is considered with reference to several types of classification methods and systems.

Morrison, D. B.↗
NASA NTRS1979

Dynamic analysis of a photovoltaic power system with battery storage capability

A photovolataic power system with a battery storage capability is analyzed. A dual battery current control concept is proposed, which enables the battery to either supply or accept power depending upon system environment and load conditions. A simulation of the power system, including the battery current control, is developed and evaluated. The evaulation demonstrate the visbility of the battery control concept of switch the battery from a charge to discharge mode and back as required by load and environmental conditions. An acceptable system operation is demonstrated over the entire insolation range. Additionally, system sensitivity, bandwidth, and damping characteristics of the battery control are shown to be acceptable for a projected hardware implementation.

Merrill, W. C.↗
NASA NTRS1979

Quiet short-haul research aircraft familiarization document

The design features and general characteristics of the NASA Quiet Short-Haul Research Aircraft are described. Aerodynamic characteristics and performance are discussed based on predictions and early flight-test data. Principle airplane systems, including the airborne data-acquisition system, are also described. The aircraft was designed and built to fulfill the need for a national research facility to explore the use of upper surface-blowing propulsive-lift technology in providing short takeoff and landing capability, and perform advanced experiments in various technical disciplines such as aerodynamics, propulsion, stability and control, handling qualities, avionics and flight-control systems, trailing-vortex phenomena, acoustics, structure and loads, operating systems, human factors, and airworthiness/certification criteria. An unusually austere approach using experimental shop practices resulted in a low cost and high research capability.

Mccracken, R. C.↗
NASA NTRS1980

Adaptive rain fade compensation

A large available margin must be provided for satellite communications systems operating near 20 GHz, which occasionally experience fades due to rain attenuation. It is proposed that this margin may be achieved in high-capacity FDMA satellites by dynamically providing a large margin to those links which are experiencing deep fades, while maintaining a small fade margin on all others. Single-beam SCPC operation and multiple-beam, satellite-switched FDMA systems are described, and the optimization of the dynamic FDMA links in a severely fading environment is investigated. A solution is derived which takes into account: (1) transponder intermodulation distortion, (2) cochannel and cross-polarization antenna interference, and (3) rain fade characteristics. The sample system configuration presented shows that such systems reach availability levels approaching 0.9999 at Ka-Band.

Rautio, J. C.↗
NASA NTRS1986

Advanced ATC - An aircraft perspective

The principal operational improvements desired by commercial aircraft operators in the United States are efficient aircraft operations and delay reductions at the major terminals. This paper describes efforts underway within the Advanced Transport Operating Systems Program at the Langley Research Center to provide a technology basis for reducing delay while improving aircraft efficiency. The principal thrust is the development of time-based traffic control concepts which could be used within the framework of the upgraded National Airspace System and which would allow conventionally equipped aircraft to operate in a manner compatible with advanced aircraft.

Credeur, L.↗
NASA NTRS1986

Advanced ATC: An aircraft perspective

The principal operational improvements desired by commercial aircraft operators in the United States are efficient aircraft operations and delay reductions at the major terminals. Efforts underway within the Advanced Transport Operating Systems Program at the Langley Research Center to provide a technology basis for reducing delay while improving aircraft efficiency are discussed. The principal thrust is the development of time-based traffic control concepts which could be used within the framework of the upgraded National Airspace System and which would allow conventionally equipped aircraft to operate in a manner compatible with advanced aircraft.

Credeur, Leonard↗
NASA NTRS1987

Data capture and processing

A systems concept developed in response to the specific requirements imposed by the Space Station and affiliated instrumentation is described. Particular attention is given to those subsystems associated with initial data capture, handling, routing, and distribution control for return link data via the Tracking and Data Relay Satellite System. The conceived approach, designated the Customer Data and Operations System, includes a data interface facility and a data handling center whose functions are data capture, demultiplexing and routing, early preprocessing, and ancillary data handling.

Lyon, John↗