Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Spring”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Design of a sample acquistion system for the Mars exobiological penetrator

The Mars Exobiological Penetrator will be imbedded into several locations on the Martian surface. It contains various scientific instruments, such as an Alpha-Particle Instrument (API), Differential Scanning Calorimeter (DSC), Evolved Gas Analyzer (EGA) and accelerometers. A sample is required for analysis in the API and DSC. To avoid impact contaminated material, this sample must be taken from soil greater than 2 cm away from the penetrator shell. This study examines the design of a dedicated sampling system including deployment, suspension, fore/after body coupling, sample gathering and placement. To prevent subsurface material from entering the penetrator sampling compartment during impact, a plug is placed in the exit hole of the wall. A U-lever device is used to hold this plug in the penetrator wall. The U-lever rotates upon initial motion of the core-grinder mechanism (CGM), releasing the plug. Research points to a combination of coring and grinding as a plausible solution to the problem of dry drilling. The CGM, driven by two compressed springs, will be deployed along a tracking system. A slowly varying load i.e., springs, is favored over a fixed displacement motion because of its adaptability to different material hardness. However, to accommodate sampling in a low density soil, two dash pots set a maximum transverse velocity. In addition, minimal power use is achieved by unidirectional motion of the CGM. The sample will be transported to the scientific instruments by means of a sample placement tray that is driven by a compressed spring to avoid unnecessary power usage. This paper also explores possible modifications for size, weight, and time as well as possible future studies.

Thomson, Ron↗
NASA NTRS1989

Space Shuttle Main Engine structural analysis and data reduction/evaluation. Volume 2: High pressure oxidizer turbo-pump turbine end bearing analysis

The high-pressure oxidizer turbopump (HPOTP) consists of two centrifugal pumps, on a common shaft, that are directly driven by a hot-gas turbine. Pump shaft axial thrust is balanced in that the double-entry main inducer/impeller is inherently balanced and the thrusts of the preburner pump and turbine are nearly equal but opposite. Residual shaft thrust is controlled by a self-compensating, non-rubbing, balance piston. Shaft hang-up must be avoided if the balance piston is to perform properly. One potential cause of shaft hang-up is contact between the Phase 2 bearing support and axial spring cartridge of the HPOTP main pump housing. The status of the bearing support/axial spring cartridge interface is investigated under current loading conditions. An ANSYS version 4.3, three-dimensional, finite element model was generated on Lockheed's VAX 11/785 computer. A nonlinear thermal analysis was then executed on the Marshall Space Flight Center Engineering Analysis Data System (EADS). These thermal results were then applied along with the interference fit and bolt preloads to the model as load conditions for a static analysis to determine the gap status of the bearing support/axial spring cartridge interface. For possible further analysis of the local regions of HPOTP main pump housing assembly, detailed ANSYS submodels were generated using I-DEAS Geomod and Supertab (Appendix A).

Sisk, Gregory A.↗
NASA NTRS1989

Fossil life on Mars

Three major problems beset paleontologists searching for morphological evidence of life on early Earth: selecting a prospective site; finding biogenic structures; and distinguishing biogenic from abiogenic structures. The same problems arise on Mars. Terrestrial experience suggests that, with the techniques that can be employed remotely, ancient springs, including hot springs, are more prospective than lake deposits. If, on the other hand, the search is for chemical evidence, the strategy can be very different, and lake deposits are attractive targets. Lakes and springs frequenly occur in close proximity, and therefore a strategy that combines the two would seem to maximize the chance of success. The strategy for a search for stromatolite on Mars is discussed.

Walter, M. R.↗
NASA NTRS1990

Turbomachinery rotor support with damping

Damping seals, damping bearings, and a support sleeve are presented for the ball bearings of a high speed rotor. The ball bearings consist of a duplex set having the outer races packaged tightly within the sleeve while the sleeve provides a gap with a support member so that the bearings may float with the sleeve. The sleeve has a web extending radially between the pair of outer races and acts in conjunction with one or more springs to apply an axial preload to the outer races. The sleeves have a series of slits which provide the sleeve with a spring-like quality so that the spring acts to center the rotor upon which the bearings are mounted during start up and shut down. A damping seal or a damping bearing may be used in conjunction with the ball bearings and supporting sleeve, the damping seal and damping bearing having rotor portions including rigid outer surfaces mounted within the bore of a stator portion having triangular shaped pockets on the surface facing the rotor. Axial gates are provided between adjacent pockets in sections of the stator permitting fluid to flow with less resistance axially relative to the flow of fluids circumferentially between the rotor and the stator.

Vonpragenau, George L.↗
NASA NTRS1991

SMA applications in an innovative multishot deployment mechanism

An innovative Deployment and Retraction hinge Mechanism (DARM) in the frame of a technological program is examined. The mechanism includes two restraint/release devices, which enable it to be stable in its stowed or deployed position while sustaining all associated loads, and to carry its payload by remote command. The main characteristics of the DARM are as follows: deployment and retraction movements are spring actuated; the available amount of functional sequences is almost unlimited; and no use of electrical motors is made. These features were accomplished by: the application of a special kinematic scheme to the mechanical connection between the spring motor and the swivel head arm; and the use of shape memory alloys (SMA) actuators for both release and spring recharge functions. DARM is thus a mechanism which can find many applications in the general space scenario of in-orbit maintenance and servicing. In such a frame, the DARM typical concept, which has a design close to very simple one-shot deployment mechanisms, has a good chance to replace existing analog machines. Potential items that could be moved by DARM are: booms for satellite instruments; antenna reflector tips; entire antenna reflectors; and solar panels.

Stella, D.↗
NASA NTRS1991

Quick application/release nut with engagement indicator (commercial application of an innovative nut design)

This is an assembly which permits a fastener to be inserted or removed from either side with an indicator of fastener engagement. The nut has a plurality of segments, preferably at least three segments, which are internally threaded, spring loaded apart by an internal spring, and has detents on opposite sides which force the nut segments into operative engagement with a threaded member when pushed in and release the segments for quick insertion or removal of the fastener when moved out. When the nut is installed, end pressure on the detents presses the nut segments into operative engagement with a threaded member where continued rotation locks the structure together with the detents depressed to indicate positive locking engagement of the nut. On removal, counterclockwise rotation relieves the endwise pressure on the detents, permitting internal springs to force the detents outward, allowing the nut segments to move outward and separate to permit quick removal of the fastener.

Wright, Jay M.↗
NASA NTRS1992

Quick application/release nut with engagement indicator

A composite nut is shown which permits a fastener to be inserted or removed from either side with an indicator of fastener engagement. The nut has a plurality of segments, preferably at least three segments, which are internally threaded, spring loaded apart by an internal spring, and has detents on opposite sides which force the nut segments into operative engagements with a threaded member when pushed in and release the segments for quick insertion or removal of the nut when moved out. When the nut is installed, end pressure on one of the detents presses the nut segments into operative engagement with a threaded member where continued rotation locks the structure together with the detents depressed to indicate positive locking engagement of the nut. On removal, counterclockwise rotation of the nut relieves the endwise pressure on the detents, permitting internal springs to force the detents outward and allowing the nut segments to move outward and separate to permit quick removal of the fastener.

Wright, Jay M.↗
NASA NTRS1991

GRIS instrument continuum results from SN1987A

Results on the continuum emission from SN1987A from two balloon flights of gamma-ray imaging spectrometer over Alice Springs, Australia, in the spring and fall of 1988 are presented. The durations of the two observations were 11.2 and 11.7 hours, respectively. The measured continuum spectra (95-2560 keV for the spring and 55-2560 keV for the fall) are consistent with Compton scattering of the Co-56 decay lines. The 10HMM model agrees well with continuum data in the energy dependence of the continuum both in the slope of the spectra and the step increases below the 2599, 1238, and 847 keV Co-56 decay lines.

Barthelmy, S.↗
NASA NTRS1992

Power assist EVA glove development

Structural modeling of the EVA glove indicates that flexibility in the metacarpophalangeal (MCP) joint can be improved by selectively lowering the elasticity of the glove fabric. Two strategies are used to accomplish this. One method uses coil springs on the back of the glove to carry the tension in the glove skin due to pressurization. These springs carry the loads normally borne by the glove fabric, but are more easily deformed. An active system was also designed for the same purpose and uses gas filled bladders attached to the back of the EVA glove that change the dimensions of the back of the glove and allow the glove to bend at the MCP joint, thus providing greater flexibility at this joint. A threshold control scheme was devised to control the action of the joint actuators. Input to the controller was provided by thin resistive pressure sensors placed between the hand and the pressurized glove. The pressure sensors consist of a layer of polyester film that has a thin layer of ink screened on the surface. The resistivity of the ink is pressure dependent, so an extremely thin pressure sensor can be fabricated by covering the ink patch with another layer of polyester film and measuring the changing resistance of the ink with a bridge circuit. In order to sense the force between the hand and the glove at the MCP joint, a sensor was placed on the palmar face of the middle finger. The resultant signal was used by the controller to decide whether to fill or exhaust the bladder actuators on the back of the glove. The information from the sensor can also be used to evaluate the effectiveness of a given control scheme or glove design since the magnitude of the measured pressures gives some idea of the torque required to bend a glove finger at the MCP joint. Tests of this actuator, sensor, and control system were conducted in an 57.2 kPa glove box by performing a series of 90 degree finger bends with a glove without an MCP joint assembly, a glove with the coil spring assembly, and with the four fingered actuated glove. The tests of these three glove designs confirm the validity of the model.

Main, John A.↗
NASA NTRS1954

Flight Tests of a Man Standing on a Platform Supported by a Teetering Rotor

Because previous flight tests of a man standing on a jet-supported platform were very successful, a series of flight tests were made to determine the flying qualities of a man standing on a platform supported by a teetering rotor. The rotor was 7 feet in diameter and was driven by air jets at the rotor tips fed by hollow blades and air hoses connected to an external air supply. The machine was tested with a free-teetering rotor and with a spring-restrained rotor, and, as an alternate arrangement, with the rotor and foot platform isolated from the framework by rubber connections to reduce the inertia of the moving parts. The machine was tested indoors in hovering and in limited translational flight and outdoors in light and in strong gusty winds. The stability and controllability with the spring-restrained rotor were uniformly good. The stability with the free-teetering rotor was marginal, but, when an experienced flyer placed his hands on a hand rail, the stability and controllability were good. The stability and controllability with the rubber-isolated frame and spring-restrained teetering rotor were very good and quite like the jet-supported platform.

Paul R Hill↗
NASA NTRS1930

Pressure element of constant logarithmic stiffness for temperature compensated altimeter

The usual type of altimeter contains a pressure element, the deflections of which are approximately proportional to pressure changes. An evenly divided altitude scale is secured by using a mechanism between the pressure element and pointer which gives the required motion of the pointer. A temperature-compensated altimeter was constructed at the Bureau of Standards for the Bureau of Aeronautics of the Navy Department which contained a manually operated device for controlling the multiplication of the mechanism to the extent necessary for temperature compensation. The introduction of this device made it difficult to adjust the multiplying mechanism to fit an evenly divided altitude scale. To meet this difficulty a pressure element was designed and constructed which gave deflections which were proportional to altitude; that is, to the logarithm of the pressure. The element consisted of a metal bellows of the sylphon type coupled to an internal helical spring which was designed so as to have a variable number of active coils. This report presents a description of and laboratory data relating to the special pressure element for the altimeter. In addition equations which apply generally to springs and pressure elements of constant logarithmic stiffness are developed, including the deflection and the spacing between the coils in terms of the constants of the helical spring and pressure elements. (author)

Brombacher, W G↗
NASA NTRS1930

Experimental and Analytical Determination of the Motion of Hydraulically Operated Valve Stems in Oil Engine Injection Systems

This research on the pressure variations in the injection system of the N.A.C.A. Spray Photography Equipment and on the effects of these variations on the motion of the timing valve stem was undertaken in connection with the study of fuel injection systems for high-speed oil engines. The methods of analysis of the pressure variations and the general equation for the motion of the spring-loaded stem for the timing valve are applicable to a spring-loaded automatic injection valve, and in general to all hydraulically operated valves. A sample calculation for a spring-loaded automatic injection valve is included.

Gelalles, A G↗
NASA NTRS1954

On force-deflection diagrams of airplane shock absorber struts : first, second, and third partial reports

This paper, which is presented in three parts, is an analytical study of the behavior of landing gear shock struts, with various types of assumptions for the shock-strut characteristics. The effects of tire springing are neglected. The first part compares the behavior of struts with linear and quadratic damping. The second part considers struts with nonlinear spring characteristics and linear or quadratic damping. The third part treats the oleo-pneumatic strut with air-compression springing without damping and with damping proportional to velocity. It is indicated how the damping factor can be determined by experiment.

LOADS, LANDING - IMPACT, LAND↗
NASA NTRS1994

Torsion And Bending Alleviator

Device couples two shafts while relieving excessive loads between them. Torsion and bending loads between upper and mounting shafts relieved in coupling by ball springs and Belleville springs, respectively. Both sets of springs adjustable so as not to relieve loads below preset limits.

Doebbler, Thomas R.↗
NASA NTRS1993

Mechanical energy absorber

An energy absorbing system for controlling the force where a moving object engages a stationary stop and where the system utilized telescopic tubular members, energy absorbing diaphragm elements, force regulating disc springs, and a return spring to return the telescoping member to its start position after stroking is presented. The energy absorbing system has frusto-conical diaphragm elements frictionally engaging the shaft and are opposed by a force regulating set of disc springs. In principle, this force feedback mechanism serves to keep the stroking load at a reasonable level even if the friction coefficient increases greatly. This force feedback device also serves to desensitize the singular and combined effects of manufacturing tolerances, sliding surface wear, temperature changes, dynamic effects, and lubricity.

Wesselski, Clarence J.↗
NASA NTRS1994

Ground based NO2 and O3 measurements by visible spectrometer at Syowa Base (69 deg S), Antarctica

The column amounts of NO2 and ozone have been measured using visible spectroscopy at Syowa Base (69 deg S) since March 1990. Ozone was also measured at the same location with a Dobson spectrometer as well as ozonesondes being flown regularly. The characteristic features of the seasonal and diurnal variations of NO2 are presented. The column ozone values from the visible spectrometers are compared with the Dobson data. The very low values of NO2 in midwinter and early spring are consistent with the conditions predicted to be needed for heterogeneous ozone destruction in early spring. In late spring and summer of 1991, NO2 amounts were considerably smaller than in 1990, presumably due to the effect of Mt. Pinatubo eruption.

Kondo, Y.↗
NASA NTRS1994

Design of passive piezoelectric damping for space structures

Passive damping of structural dynamics using piezoceramic electromechanical energy conversion and passive electrical networks is a relatively recent concept with little implementation experience base. This report describes an implementation case study, starting from conceptual design and technique selection, through detailed component design and testing to simulation on the structure to be damped. About 0.5kg. of piezoelectric material was employed to damp the ASTREX testbed, a 500kg structure. Emphasis was placed upon designing the damping to enable high bandwidth robust feedback control. Resistive piezoelectric shunting provided the necessary broadband damping. The piezoelectric element was incorporated into a mechanically-tuned vibration absorber in order to concentrate damping into the 30 to 40 Hz frequency modes at the rolloff region of the proposed compensator. A prototype of a steel flex-tensional motion amplification device was built and tested. The effective stiffness and damping of the flex-tensional device was experimentally verified. When six of these effective springs are placed in an orthogonal configuration, strain energy is absorbed from all six degrees of freedom of a 90kg. mass. A NASTRAN finite element model of the testbed was modified to include the six-spring damping system. An analytical model was developed for the spring in order to see how the flex-tensional device and piezoelectric dimensions effect the critical stress and strain energy distribution throughout the component. Simulation of the testbed demonstrated the damping levels achievable in the completed system.

Hagood, Nesbitt W., IV↗
NASA NTRS1995

Evidence of seasonally dependent stratosphere-troposphere exchange and purging of lower stratospheric aerosol from a multiyear lidar data set

Tropospheric and lower stratospheric aerosol backscatter data obtained from a calibrated backscatter lidar at Pasadena, California (34 deg N latitude) over the 1984-1993 period clearly indicate tightly coupled aerosol optical properties in the upper troposphere and lower stratosphere in the winter and early spring, due to the active midlatitude stratospheric-tropospheric (ST) exchange processes occurring at this time of year. Lidar data indicate that during pre-Pinaturbo background conditions, the subsequent purging of the aerosol in the upper troposphere caused a significant reduction in the aerosol content throughout the 8 - 18 km altitude region in the early spring period. The post-Pinatubo evidence of intense exchange in the winter and early spring is a significant increase in the upper tropospheric aerosol content, such that the backscatter levels reach values nearly equivalent to the enhanced backscatter levels existing in the lower stratosphere. The calculated stratospheric mass extrusion rate is consistent with a 45-day lifetime of lower stratospheric aerosol during this part of the year, which implies that midlatitude ST exchange is a significant sink for stratospheric aerosol.

Menzies, Robert T.↗