Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Scanning Electron Microscopy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Properties of mortars made by uncalcined FGD gypsum-fly ash-ground granulated blast furnace slag composite binder

Highlights: Black-Right-Pointing-Pointer The mortar with uncalcined FGD gypsum has suitable workability. Black-Right-Pointing-Pointer The strength of mortar with uncalcined FGD gypsum is higher than that of mortar without uncalcined FGD gypsum. Black-Right-Pointing-Pointer The dry shrinkage of mortar with uncalcined FGD gypsum is lower than that of mortar without uncalcined FGD gypsum. Black-Right-Pointing-Pointer The leaching of sulfate ion of mortar is studied. - Abstract: A series of novel mortars were developed from composite binder of uncalcined FGD gypsum, fly ash (FA) and ground granulated blast furnace slag (GGBFS) for the good utilization of flue gas desulphurization (FGD) gypsum. At a fixed ratio (20%) of GGBFS to the composite binder, keeping consistency of the mortar between 9.5 and 10.0 cm, the properties of the composite mortar were studied. The results show that higher water/binder (W/B) is required to keep the consistency when increasing the percentage of FGD gypsum. No obvious influences of the W/B and content of FGD gypsum on the bleeding of paste were observed which keeps lower than 2% under all experimental conditions tried. The highest compressive and flexural strengths (ratio is 20% FGD gypsum, 20% GGBFS and 60% FA) are 22.6 and 4.3 MPa at 28 days, respectively. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) results indicate that massive ettringite crystals and C-S-H gels exist in the hydration products. At 90 days the mortars with FGD gypsum is dramatically smaller drying shrinkage (563-938 micro strain) than that without FGD gypsum (about 2250 micro strain). The release of the SO{sub 4}{sup 2-} from the mortar was analyzed, indicating that the dissolution of sulfate increases with FGD gypsum. The concentration of SO{sub 4}{sup 2-} releasing from the mortar with 10% FGD gypsum is almost equal to that obtained from the mortar without FGD gypsum. The release of SO{sub 4}{sup 2-} from the mortar with 20% FGD gypsum is 9200 mg{center_dot}m{sup -2}, which is lower than that from the mortar with 95% cement clinker and 5% FGD gypsum.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Characterization, sintering and dielectric properties of nanocrystalline barium titanate synthesized through a modified combustion process

Nanocrystalline barium titanate has been synthesized through a modified combustion process in a single step for the first time. The as-prepared barium titanate powder is cubic perovskite with lattice constant a = 4.018 A. The phase purity of the nanopowder was examined using thermo gravimetric analysis, differential thermal analysis and Fourier transform infrared spectroscopy. Transmission electron microscopic investigations have shown that the particle size of the as-prepared powder is in the range 20-40 nm. The agglomerate size distribution of the as-prepared powder was studied using atomic force microscopy. The nanoparticles of barium titanate were sintered to 97% of the theoretical density at a temperature of 1350 deg. C for 3 h. The microstructure of the sintered surface was examined using scanning electron microscopy. The dielectric constant and loss factor of the sintered pellets at 1 MHz measured at room temperature were 1223 and 3.5 x 10{sup -3} respectively.

36 MATERIALS SCIENCE↗

Dielectric and ferroelectric response of compositionally graded bilayer and trilayer composites of BaTiO{sub 3} and 0.975BaTiO{sub 3}-0.025Ba(Cu{sub 1/3}Nb{sub 2/3})O{sub 3}

In this paper, we report the dielectric and ferroelectric response of compositionally graded bilayer and trilayer composites consisting of BaTiO{sub 3} (BT) and 0.975BaTiO{sub 3}-0.025Ba(Cu{sub 1/3}Nb{sub 2/3})O{sub 3} (BTBCN). Two types of graded bilayer samples were synthesized, one with same thickness of BT and BTBCN while other with different layer thicknesses. The graded trilayer sample consisted of BT layer sandwiched between two BTBCN layers of equal thickness. Scanning electron microscopy and transmission electron microscopy images showed a sharp interface with needle-shape domains across the interface. The domain size on BT side was found to be larger than that on BTBCN side. The temperature dependence of dielectric response for all composite systems was found to exhibit shifting in characteristic Curie peak compared to constituent material which was associated to coupling between layers. Moreover, the differences in grain size, tetragonality, domain mobility of each layer was found to perturb the electrical response of composite. The polarization mismatch between uncoupled BT and BTBCN established internal electric field in composite specimen and defined new polarization states in each layer by perturbing free energy functional of the composite specimen. Dynamic hysteresis behaviors and power-law scaling relations of all specimens were determined from polarization-electric field hysteresis loop measurements as a function of frequency. All systems were found to exhibit similar dynamic scaling relationships. Hysteresis area <A>, P{sub r}, and E{sub C} decreased with increasing frequency due to delayed response but increased with increasing applied electric field due to enhancement of driving force. Trilayer system was found to exhibit strong internal-bias field and double hysteresis behavior. The coupling effect resulting due to polarization mismatch between layers had substantial influence on the dynamic hysteresis behavior and power-law scaling relations.

36 MATERIALS SCIENCE↗

Deposition and characterization of molybdenum thin films using dc-plasma magnetron sputtering

Molebdenum (Mo) thin films were deposited on well-cleaned soda-lime glass substrates using DC-plasma magnetron sputtering. In the design of experiment deposition was optimized for maximum beneficial characteristics by monitoring effect of process variables such as deposition power (100–200 W). Their electrical, structural and morphological properties were analyzed to study the effect of these variables. The electrical resistivity of Mo thin films could be reduced by increasing deposition power. Within the range of analyzed deposition power, Mo thin films showed a mono crystalline nature and the crystallites were found to have an orientation along [110] direction. The surface morphology of thin films showed that a highly dense micro structure has been obtained. The surface roughness of films increased with deposition power. The adhesion of Mo thin films could be improved by increasing the deposition power. Atomic force microscopy was used for the topographical study of the films and to determine the roughness of the films. X-ray diffractrometer and scanning electron microscopy analysis were used to investigate the crystallinity and surface morphology of the films. Hall effect measurement system was used to find resistivity, carrier mobility and carrier density of deposited films. The adhesion test was performed using scotch hatch tape adhesion test. Mo thin films prepared at deposition power of 200 W, substrate temperature of 23°C and Ar pressure of 0.0123 mbar exhibited a mono crystalline structure with an orientation along (110) direction, thickness of ∼550 nm and electrical resistivity value of 0.57 × 10{sup −4} Ω cm.

36 MATERIALS SCIENCE↗

Rapid thermal annealing effect on amorphous hydrocarbon film deposited by CH{sub 4}/Ar dielectric barrier discharge plasma on Si wafer: Surface morphology and chemical evaluation

The effects of rapid thermal annealing (RTA) on amorphous hydrogenated carbon-coated film on Si wafer, deposited by CH{sub 4}/Ar dielectric barrier discharge plasma (at half of the atmospheric pressure), was examined. Bubbles-like structures were formed on the surface of the deposited carbon-coated film. The surface morphology studied by scanning electron microscopy (SEM), which showed that the effect of RTA on the film changing the morphological property drastically at 600 deg. C and most of the bubbles started evaporating above 200 deg. C. The inbuilt energy dispersive x-ray in SEM gives the quantitative analysis of the annealed surface. X-ray photoelectron spectroscopy results of the as-deposited films agree with the IR results in that the percent of Si-CH{sub 3}, Si-O-Si and C-O(H) stretching vibrational band in the film. Most of these bands disappeared as the sample was annealed at 600 deg. C in Ar medium.

36 MATERIALS SCIENCE↗

Corrosion-induced microstructural developments in 316 stainless steel during exposure to molten Li 2 BeF 4 (FLiBe) salt

The microstructural evaluation and characterization of 316 stainless steel samples that were tested in molten Li 2 BeF 4 (FLiBe) salt were investigated in this study for evaluating its performance in high-temperature molten fluoride salts. Recently, 316 stainless steel and FLiBe salt are being actively considered as the main structural alloy and primary coolant of fluoride salt-cooled high-temperature reactor (FHR), a leading nuclear reactor concept for the next generation nuclear plants (NGNP). In support of the materials development for the FHR, high-temperature corrosion tests of 316 stainless steel in molten FLiBe salt at 700°C have been conducted in both bare graphite crucibles and 316 stainless steel-lined crucibles in an inert atmosphere for up to 3000 hours. The microstructure of the tested samples was comprehensively characterized using scanning electron microscopy (SEM) in conjunction with energy dispersive x-ray spectroscopy (EDS) and electron backscatter diffraction (EBSD), and scanning transmission electron microscopy (STEM) with EDS. In addition to the noticeable intergranular corrosion attack on surface, the corrosion in terms of the Cr depletion along high angle grain boundaries (15-180º) extended to 22µm in depth after 3000-hour exposure to molten FLiBe salt in graphite crucible. The coherent Σ3 grain boundary appeared high resistance to the Cr depletion. The substantial Cr depletion from the near-to-surface layer induced phase transformation from γ-martensite to α-ferrite phase (FeNi x ) during corrosion at 700ºC. Furthermore, the presence of graphite in the molten salt doubled the corrosion attack depth and led to the formation of round Mo2C, hexagonal Cr 7 C 3 and needle-like Al 4 C 3 phase within the alloy as deep as 50 µm after 3000-hour corrosion testing. Based on the microstructural analysis, the corrosion mechanisms of 316 stainless steel in molten FLiBe salt in different corrosion crucibles were illuminated through schematic diagrams. Additionally, a thermal diffusion controlled corrosion model was developed and validated by experimental data for predicting the long-term corrosion attack depth.

36 MATERIALS SCIENCE↗

Effect of anodization parameters on the structural morphology of titanium in fluoride containing electrolytes

In the present work, formation of titania nanopores on titanium substrate was investigated in aqueous (sulphuric acid) and neutral organic (glycerol) electrolytes containing different concentrations of HF (0.1-0.2 M). The surface morphology, topography and phase structures were analyzed using scanning electron microscopy, atomic force microscopy and X-ray diffraction techniques, respectively. Under optimized electrolyte conditions, titania nanopore is obtained with the average pore diameter of 64 nm and 84 nm for aqueous and organic electrolytes, respectively. Atomic force microscope investigation shows that the porous layer forms under a competition of titania formation and oxide dissolution up to a limiting thickness of {approx} 75 nm and 100 nm respectively for aqueous and organic electrolytes. The porous structure was observed at 0.15 M HF concentration. It was found that depending on the electrolytes the pore diameter alters and also its concentration effected the porous structures formation. Compared to aqueous electrolytes, organic electrolytes showed larger diameter pores. From the X-ray diffraction measurement it is evident that the as prepared titania nanopores are amorphous in nature, whereas the anodized heat treated titania nanopores are in anatase phase. - Highlights: Black-Right-Pointing-Pointer Aqueous and organic electrolytes were used to synthesize nanoporous titania. Black-Right-Pointing-Pointer The surface morphology varies with various concentrations of HF. Black-Right-Pointing-Pointer Nanopores were formed at optimum HF concentration of 0.15 M. Black-Right-Pointing-Pointer Nanopore diameter was found to be affected by the electrolyte used.

36 MATERIALS SCIENCE↗

Synthesis and characterization of brownmillerite SrFeO{sub 2.5} in nanostructured form

Synthesis of bulk polycrystalline and nanocrystalline oxygen-deficient SrFeO{sub 2.5} compounds, with potential applications as oxygen membranes, has been explored by chemical route to optimize an easy and reproducible method for high yield. The structure of the samples was investigated by X-ray powder diffraction followed by structural refinement. Both bulk and nanocrystalline SrFeO{sub 2.5} crystallize in Imma space group. X-ray powder diffraction pattern corresponds to the brownmillerite structure in which the Fe cations exist in an octahedral or tetrahedral configuration in alternate layers along the b axis. Brunauer−Emmett−Teller (BET) surface area is found to be 0.40m{sup 2}/g and 14 m{sup 2}/g for bulk and nanocrystalline SrFeO{sub 2.5} respectively. The morphology of these materials was also investigated by scanning electron microscopy and transmission electron microscopy.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Preparation and luminescence properties of Ce{sup 3+} and/or Tb{sup 3+} doped LaPO{sub 4} nanofibers and microbelts by electrospinning

Ce{sup 3+} and/or Tb{sup 3+} doped LaPO{sub 4} nanofibers and microbelts have been prepared by a combination method of sol-gel process and electrospinning. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), photoluminescence (PL), low voltage cathodoluminescence (CL) and time-resolved emission spectra as well as kinetic decays were used to characterize the resulting samples. SEM and TEM results indicate the as-formed precursor fibers and belts are smooth, and the as-prepared nanofibers and microbelts consist of nanoparticles. The doped rare-earth ions show their characteristic emission under ultraviolet excitation, i.e. Ce{sup 3+} 5d-4f and Tb{sup 3+5}D{sub 4}-{sup 7}F{sub J} (J=6-3) transitions, respectively. The energy transfer process from Ce{sup 3+} to Tb{sup 3+} in LaPO{sub 4}:Ce{sup 3+}, Tb{sup 3+} nanofibers was further studied by the time-resolved emission spectra. Under low-voltage electron beam excitation, LaPO{sub 4}:Ce{sup 3+}, Tb{sup 3+} microbelt phosphors have a higher intensity than that of nanofiber phosphors. - Graphical Abstract: Ce{sup 3+} and/or Tb{sup 3+} LaPO{sub 4} nanofibers and microbelts have been prepared by electrospinning. A systematic study on the optical properties of LaPO{sub 4}:Ce{sup 3+}, Tb{sup 3+} samples has shown that they are good green-emitting phosphors in fluorescent lamps and field emission displays. The energy transfer process from Ce{sup 3+} to Tb{sup 3+} in LaPO{sub 4}:Ce{sup 3+}, Tb{sup 3+} nanofibers is further studied by the time-resolved emission spectra.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Tailoring oxidation of aluminum nanoparticles reinforced with carbon nanotubes

In this report, the oxidation temperature and reaction enthalpy of Aluminum (Al) nanoparticles has been controlled by reinforcing with carbon nanotubes. The physical mixing method with ultrasonication was employed to synthesize CNT/Al nanocomposite powders. The micro-morphology of nanoconmposite powders has been analysed by scanning electron microscopy, energy dispersive spectroscopy, Raman spectroscopy and X-ray diffraction techniques. The oxidation behavior of nanocomposite powders analyzed by thermogravimetry/differential scanning calorimertry showed improvement in the exothermic enthalpy. Largest exothermic enthalpy of-1251J/g was observed for CNT (4 wt%)/Al nanocomposite.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Surface modification and optical properties of metal doped indium sulfide thin films

Indium sulfide (In{sub 2}S{sub 3}) thin films were prepared by chemical bath deposition method in same deposition conditions, and then doped by metals including Ag, Al and Cu. Produced films post annealed at 400 °C temperature about 1 h. The effects of different metal-doping on structural, morphological and optical properties of the films were investigated by means of X-ray diffraction, scanning electron microscopy, atomic force microscopy and UV–Vis spectroscopy analyses. Produced indium sulfide thin film was amorphous and doping process lead to shifts peaks in lower angles. Morphology and nanostructure of doped films changed completely. Compact doped films have been formed. Optical constants of the produced thin films were calculated using Kramers–Kronig relations on reflectivity curves. Different doping impurities changed optical curves and band gaps.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Electron microscopy study of the microstructure of Ni–W substrate surface

The surface microstructure of Ni–W alloy tapes, which are used as substrates to form films of high-temperature superconductors and photovoltaic devices, has been studied. Several samples of a Ni{sub 95}W{sub 5} tape (Evico) annealed under different conditions were analyzed using scanning electron microscopy, energy-dispersive X-ray microanalysis, electron diffraction, and electron energy-loss spectroscopy. NiWO{sub 4} precipitates are found on the surface of annealed samples. The growth of precipitates at a temperature of 950°C is accompanied by the formation of pores on the surface or under an oxide film. Depressions with a wedge-shaped profile are found at the grain boundaries. Annealing in a reducing atmosphere using a specially prepared chamber allows one to form a surface free of nickel tungstate precipitates.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Dependence of catalytic properties of Al/Fe{sub 2}O{sub 3} thermites on morphology of Fe{sub 2}O{sub 3} particles in combustion reactions

Three Fe{sub 2}O{sub 3} particle samples with the same crystal structure but different morphologies were prepared by the hydrothermal method and then combined with Al nanoparticles to produce Al/Fe{sub 2}O{sub 3} thermites using ultrasonic mixing. The properties of Fe{sub 2}O{sub 3} and Al/Fe{sub 2}O{sub 3} were studied using a combination of experimental techniques including scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and differential scanning calorimetry (DSC). The influences of the three Al/Fe{sub 2}O{sub 3} thermites on the combustion properties of the AP/HTPB (ammonium perchlorate/hydroxyl-terminated polybutadiene) composite propellant were investigated in comparison to those of Fe{sub 2}O{sub 3}. The results show that the Al/Fe{sub 2}O{sub 3} thermites are better than Fe{sub 2}O{sub 3} in enhancing the combustion performance of AP/HTPB. Furthermore, the surface area, which depends on size and mophology, of Fe{sub 2}O{sub 3} particles was found to play a vital role in improving the burning rate of the thermites-containing propellant formulation, with the smallest particles with the largest surface-to-volume (S/V) ratio performing the best. The enhanced catalytic property of the granular-shape Fe{sub 2}O{sub 3} and the corresponding thermite is attributed to the large specific surface area of Fe{sub 2}O{sub 3}. The different thermal behaviors of these three superthemites were supposed to be attributed to the surface site of Fe{sub 2}O{sub 3} particles. This work provides a better understanding on the catalytic properties of thermites that are important for combustion applications. - Graphical abstract: Effects of Fe{sub 2}O{sub 3} and Al/Fe{sub 2}O{sub 3} have been compared for the first time by analyzing combustion properties of formulations containing them, suggesting their potential application in AP/HTPB composite propellant systems. - Highlights: • Three Fe{sub 2}O{sub 3} particles with different morphologies (polyhedral, oval and granular) were prepared by the hydrothermal method. • Thermal behaviors of thermites Al/Fe{sub 2}O{sub 3} are studied upon DSC data. • Effects of Fe{sub 2}O{sub 3} and Al/Fe{sub 2}O{sub 3} on the combustion properties of the AP/HTPB composite propellant are first investigated.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Facile fabrication of rutile monolayer films consisting of well crystalline nanorods by following an IL-assisted hydrothermal route

In this study, rutile films consisting of rectangular nanorods were facilely deposited on glass substrates from strongly acid solution of TiCl{sub 4}. The highly ordered array of nanorods was realized in presence of ionic liquid (IL) of [Bmim]Br by following a hydrothermal process. In this process, Degussa P25 nanoparticles served as seeds that were pre-deposited on the substrates to facilitate the array of rutile nanorods. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Raman spectrum were used to characterize the obtained nanorod films. The measurements showed that the nanorods were rectangular with width of 100-200 nm and length of more than 1 {mu}m, and grew up typically along c-axis to form the arrays against the substrate. The presence of IL was found vital for the formation of rutile nanorods, and the suitable molar ratio of [Bmim]Br to TiCl{sub 4} ranged from 500:1 to 1500:1. The excessive [Bmim]Br may hinder the precipitation of rutile particles. - Graphical abstract: The rutile film consisting of rectangular nanorods is successfully deposited on glass substrate in presence of ionic liquid (IL) of [Bmim]Br. The nanorods were rectangular with width of 100-200 nm and length of more than 1 {mu}m, which grew up typically along c-axis to form the arrays against the substrate.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Template Synthesis Of Copper Nanowires Via Electrodeposition Technique And Their Characterization

Copper nanowires have been synthesized successfully using template assisted electrodeposition technique. Commercial polycarbonate membrane (Whatman, Japan) having pore diameter 100 nm, thickness 10 {mu}m and pore density 10{sup 7} pores/cm{sup 2} was used as template. Scanning electron microscopy and X-ray diffraction techniques were used to characterize the synthesized copper nanowires. XRD and SEM results reveal that polycrystalline copper nanowires were obtained with fcc lattice structure having diameter equal to the diameter of the template used.

36 MATERIALS SCIENCE↗

Synthesis of uniform CdS nanowires in high yield and its single nanowire electrical property

Large-scale high quality CdS nanowires with uniform diameter were synthesized by using a rapid and simple solvothermal route. Field emission scan electron microscopy (FESEM) and transmission electron microscopy (TEM) images show that the CdS nanowires have diameter of about 26 nm and length up to several micrometres. High resolution TEM (HRTEM) study indicates the single-crystalline nature of CdS nanowires with an oriented growth along the c-axis direction. The optical properties of the products were characterized by UV-vis absorption spectra, photoluminescence spectra and Raman spectra. The resistivity, electron concentration and electron mobility of single NW are calculated by fitting the symmetric I-V curves measured on single NW by the metal-semiconductor-metal model based on thermionic field emission theory. - Graphical abstract: Large-scale high quality CdS nanowires (NWs) with uniform diameter were synthesized by using a rapid and simple solvothermal route. The reaction time is reduced to 2 h, comparing to other synthesis which needed long reaction time up to 12 h. In addition, the as-prepared CdS nanowires have more uniform diameter and high yield. More importantly, the I-V curve of present single CdS nanowire has a good symmetric characteristic as expected by the theory.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Nanoheteroepitaxy of gallium arsenide on strain-compliant silicon-germanium nanowires

Heterogeneous integration of high-quality GaAs on Si-based substrates using a selective migration-enhanced epitaxy (MEE) of GaAs on strain-compliant SiGe nanowires was demonstrated for the first time. The physics of compliance in nanoscale heterostructures was captured and studied using finite-element simulation. It is shown that nanostructures can provide additional substrate compliance for strain relief and therefore contribute to the formation of defect-free GaAs on SiGe. Extensive characterization using scanning electron microscopy and cross-sectional transmission electron microscopy was performed to illustrate the successful growth of GaAs on SiGe nanowire. Raman and Auger electron spectroscopy measurements further confirmed the quality of the GaAs grown and the high growth selectivity of the MEE process.

36 MATERIALS SCIENCE↗

XRD, Electron Microscopy and Vibrational Spectroscopy Characterization of Simulated SB6 HLW Glasses - 13028

Sample glasses have been made using SB6 high level waste (HLW) simulant (high in both Al and Fe) with 12 different frit compositions at a constant waste loading of 36 wt.%. As follows from X-ray diffraction (XRD) and optical and scanning electron microscopy (SEM) data, all the samples are composed of primarily glass and minor concentration of spinel phases which form both isometric grains and fine cubic (∼1 μm) crystals. Infrared spectroscopy (IR) spectra of all the glasses within the range of 400-1600 cm{sup -1} consist of the bands due to stretching and bending modes in silicon-oxygen, boron-oxygen, aluminum-oxygen and iron-oxygen structural groups. Raman spectra showed that for the spectra of all the glasses within the range of 850-1200 cm{sup -1} the best fit is achieved by suggestion of overlapping of three major components with maxima at 911-936 cm{sup -1}, 988-996 cm{sup -1} and 1020-1045 cm{sup -1}. The structural network is primarily composed of metasilicate chains and rings with embedded AlO{sub 4} and FeO{sub 4} tetrahedra. Major BO{sub 4} tetrahedra and BO{sub 3} triangles form complex borate units and are present as separate constituents. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗