Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STALLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Experimental investigation of the aerodynamic effects of distributed spanwise blowing on a fighter configuration

The results of wind tunnel tests at NASA Langley targeted at the performance and configurational characteristics of 0.1 and 0.13 scale model spanwise blowing (SWB) jet wing concepts are reported. The concept involves redirection of engine compressor bleed air to provide SWB at the fuselage-wing juncture near the wing leading edge. The tests covered the orientation of the outer panel nozzles, the effects of SWB operation on the performance of leading and trailing edge flaps and the effects of SWB on lateral stability. The trials were run at low speeds and angles of attack from 24-45 deg (landing). Both lift and longitudinal stability improved with the SWB, stall and leading edge vortex breakdown were delayed and performance increased with the SWB rate. Lateral stability was degraded below 20 deg angle of attack while instabilities were delayed above 20 deg due to roll damping.

Huffman, J. K.↗

Handling qualities related to stall/spin accidents of supersonic fighter aircraft

This paper reviews the handling qualities which influence the high angle of attack (AOA) behavior of supersonic fighter aircraft in order to obtain a clearer understanding of the causes of stall/spin accidents. The results show that, because modern fighters suffer more serious consequences when control is lost, good handling qualities are essential for safe operation at high AOA. Relaxed static stability used on some fighter aircraft can result in control problems at high AOA owing to inertia coupling and the difficulty of a recovery from a deep stall. Indications are that the use of departure/spin resistance and an automatic spin prevention system will greatly improve the safety record for modern supersonic fighters.

Anderson, S. B.↗

Helicopters for the future

Technology needed to provide the basis for creating a widening rotary wing market include: well defined and proven design; reductions in noise, vibration, and fuel consumption; improvement of flying and ride quality; better safety; reliability; maintainability; and productivity. Unsteady transonic flow, yawed flow, dynamic stall, and blade vortex interaction are some of the problems faced by scientists and engineers in the helicopter industry with rotorcraft technology seen as an important development for future advanced high speed vehicle configurations. Such aircraft as the Boeing Vertol medium lift Model 360 composite aircraft, the Sikorsky Advancing Blade Concept (ABC) aircraft, the Bell Textron XV-15 Tilt Rotor Aircraft, and the X-wing rotor aircraft are discussed in detail. Even though rotorcraft technology has become an integral part of the military scene, the potential market for its civil applications has not been fully developed.

Ward, J. F.↗

NASA's role in aeronautical research

Past and current research in the aeronautical field conducted by NASA is reviewed. The first national center for aeronautical research, the Langley Memorial Aeronautical Laboratory, was established in 1917 by the then formed National Advisory Committee for Aeronautics (NACA). Two other research centers established later by NACA (Lewis and Ames) were staffed with research cadres from Langley. These three research centers formed the nucleus of NASA when it was established in 1958. Studies conducted today by NASA's research centers include: a concept for commuter-style aircraft, turbofan engines for military supersonic fighter aircraft, strength and durability of man-made fiber materials, and maneuverability problems in high speed aircraft. In addition, at Ames, research is being conducted on short-haul aviation, and short and vertical takeoff while at Lewis studies concentrate on propulsion system and engines. At Langley the emphasis is on basic research, stressing aircraft structure improvements, stall avoidance and noise abatement. Finally, the importance of NASA's educational program is discussed.

Parker, M.↗

Inlet boundary layer effects in an axial compressor rotor. II - Throughflow effects

This paper presents results of an experimental aerodynamic study conducted in the rotating frame of reference downstream of an isolated compressor rotor with both thick and thin inlet endwall boundary layers. The paper focuses on those aspects of the data having particular significance to the assumptions and application of throughflow theory. These aspects include the spanwise distributions of static pressure and blockage, and the radial redistribution of fluid as it passes through the blade row. It is demonstrated that the main contributions to total pressure loss, blockage, and the distortion of the static pressure field were due to the hub corner stall and tip leakage. This is a significant departure from previous conclusions which looked to the endwall boundary layer and to secondary flow as major loss and blockage producing mechanisms.

Wagner, J. H.↗

Extended aeroelastic analysis for helicopter rotors with prescribed hub motion and blade appended penduluum vibration absorbers

The mathematical development for the expanded capabilities of the G400 rotor aeroelastic analysis was examined. The G400PA expanded analysis simulates the dynamics of all conventional rotors, blade pendulum vibration absorbers, and the higher harmonic excitations resulting from prescribed vibratory hub motions and higher harmonic blade pitch control. The methodology for modeling the unsteady stalled airloads of two dimensional airfoils is discussed. Formulations for calculating the rotor impedance matrix appropriate to the higher harmonic blade excitations are outlined. This impedance matrix, and the associated vibratory hub loads, are the rotor dynamic characteristic elements for use in the simplified coupled rotor/fuselage vibration analysis (SIMVIB). Updates to the development of the original G400 theory, program documentation, user instructions and information are presented.

Bielawa, R. L.↗

Experiences with nonsynchronous forced vibration in centrifugal compressors

The high subsynchronous vibrations which are often forced vibrations caused by flow instabilities, such as stage stall were examined. Modifications to improve the rotor stability by changing the bearings or seals have little effects on the subsynchronous vibrations. Understanding of the differences between forced vibrations and self excited vibrations to properly diagnose the problem and to correct it, is recommended. A list of characteristics of the two types of subsynchronous vibration is presented.

Smith, D. R.↗

Influence of stationary components on unsteady flow in industrial centrifugal compressors

An experimental investigation was performed to determine the characteristics of the onset and the growth of rotating nonuniform flow in a standard low specific speed stage, normally utilized in high pressure applications, in relation to change of stationary component geometry. Four configurations, differing only in the return channel and crossover geometry were tested on an atmospheric pressure open loop test rig. Experimental results make conspicious the effect of return channel geometry and give the possibility of shifting the unstable zone onset varying such geometry. An attempt was made to interpret the experimental results in the Emmons - Stenning's rotating stall theory.

Bonciani, L.↗

Full scale experiments into the use of large eddy breakup devices for drag reduction on aircraft

An experimental investigation in flight was performed to explore the feasibility of using LEBU (Large-Eddy-Breakup) devices to reduce the drag of aircraft. Two geometrical shapes of ribbons were used, and the development of local skin friction was monitored downstream. The aircraft was a swept-wing attack aircraft, and the flights covered the entire subsonic regime from M=0.92 down to stall conditions; flight altitudes were 1, 4.5, 7 and 10 km to explore various combinations of angle of attack, Mach - and Reynolds numbers. Some information was obtained concerning the turbulence characteristics downstream, and a discussion of the downstream amplification due to the drag at the device is also presented.

Bertelrud, A.↗

Effects of inlet distortion on a static pressure probe mounted on the engine hub in an F-15 airplane

An inlet static pressure (PS2) probe was mounted on the hub of an F100 engine in an F-15 airplane. Flight test results showed that for low distortion conditions, the ratio of engine-face total pressure to static pressure agreed well with previous altitude facility data. Off-schedule operation of the inlet third ramp angle caused increased distortion of the inlet airflow during steady-state flight conditions. Data are shown for inlet third ramp excursions leading to engine stall. The relationships of inlet face total to static pressure ratio as a function of several distortion descriptors are also described.

Hughes, D. L.↗

Nonlinear problems in flight dynamics involving aerodynamic bifurcations

Aerodynamic bifurcation is defined as the replacement of an unstable equilibrium flow by a new stable equilibrium flow at a critical value of a parameter. A mathematical model of the aerodynamic contribution to the aircraft's equations of motion is amended to accommodate aerodynamic bifurcations. Important bifurcations such as, the onset of large-scale vortex-shedding are defined. The amended mathematical model is capable of incorporating various forms of aerodynamic responses, including those associated with dynamic stall of airfoils.

Tobak, M.↗

DC-10 winglet flight evaluation

The results of a flight evaluation of winglets on a DC-10 Series 10 aircraft are presented. For sensitive areas of comparison, effects of winglets were determined back to back with and without winglets. Basic and reduced span winglet configurations were tested. After initial encounter with low speed buffet, a number of acceptable configurations were developed. For maximum drag reduction at both cruise and low speeds, lower winglets were required, having leading edge devices on upper and lower winglets for the latter regime. The cruise benefits were enhanced by adding outboard aileron droop to the reduced span winglet aircraft. Winglets had no significant impact on stall speeds, high speed buffet boundary, and stability and control characteristics. Flutter test results agreed with predictions and ground vibration data. Flight loads measurement also agreed with predictions.

Source record↗

Performance improvements of a highly integrated digital electronic control system for an F-15 airplane

The NASA highly integrated digital electronic control (HIDEC) program is structured to conduct flight research into the benefits of integrating an aircraft flight control system with the engine control system. A brief description of the HIDEC system installed on an F-15 aircraft is provided. The adaptive engine control system (ADECS) mode is described in detail, together with simulation results and analyses that show the significant excess thrust improvements achievable with the ADECS mode. It was found that this increased thrust capability is accompanied by reduced fan stall margin and can be realized during flight conditions where engine face distortion is low. The results of analyses and simulations also show that engine thrust response is improved and that fuel consumption can be reduced. Although the performance benefits that accrue because of airframe and engine control integration are being demonstrated on an F-15 aircraft, the principles are applicable to advanced aircraft such as the advanced tactical fighter and advanced tactical aircraft.

Putnam, T. W.↗

Calculation of steady and unsteady airfoil flow fields via the Navier-Stokes equations

A compressible time-dependent procedure for the two-dimensional ensemble averaged Navier-Stokes equations has been applied to the isolated airfoil problem in steady and unsteady flows. The procedure solves the governing equations via the linearized block implicit technique. Turbulence is modeled either via a mixing length or turbulence energy approach. The equations are solved in general non-orthogonal form with no-slip boundary conditions applied at the airfoil surface. Results are presented for airfoils at constant incidence, an airfoil in ramp motion and an airfoil oscillating through a dynamic stall loop. In general, steady converged solutions are obtained within 70 time steps over the range of Mach numbers considered. Comparisons with measured data show good agreement between computation and measurement.

Shamroth, S. J.↗

Energy efficient engine. Fan and quarter-stage component performance report

The fan configuration for the general Electric/NASA Energy Efficient Engine was selected following an extensive preliminary design study. The fan has an inlet radius ratio of 0.342 and a specific flowrate of 208.9 Kg/sec/sq. m (42.8 1bm/sec/sq. ft). The design corrected tip speed is 411.5 m/sec (1350 ft/sec) producing a bypass flow total-pressure ratio of 1.65 and a core flow total-pressure ratio of 1.6. The design bypass ratio is 6.8. The aerodynamic design point corresponds to the maximum climb power setting at Mach 0.8 and 10.67 Km (35,000 ft) altitude. The fully-instrumented fan component was tested in the Lynn Large Fan Test Facility in 1981. The overall performance results, reported herein, showed excellent fan performance with the fan meeting all of its component test goals of flow, efficiency and stall margin.

Cline, S. J.↗

Radial migration of preplanetary material - Implications for the accretion time scale problem

Radial drift of planetesimals due to density wave interaction with the solar nebula is considered. The mechanism is most effective for large masses and provides mobility over a size range where aerodynamic drag is unimportant. The process could shorten accretion time scales to O(100,000-1,000,000 years) throughout the solar system. Accumulation stalls down when growing objects are massive enough to open gaps in the gas disk. Implications of this process for current cosmogonic models are discussed.

Hourigan, K.↗

Design parameters for flow energizers

One of the most significant uses of flow energizers, which are small highly swept strakes mounted immediately above a lifting surface, is in flow control over regions where a lifting surface is joined to another body, such as a fuselage or nacelle. In the presently reported systematic wind tunnel test study of flow energizers, 14 different geometric configurations using a 75-deg sweep flow energizer were tested on a light twin-engine general aviation aircraft model. It is found that cambered flow energizers perform better than their flat counterparts. All but two of the energizer installations developed lower L/D at cruise angles of attack, lower maximum lift coefficients, and lower stall angles of attack than the baseline model.

Ward, D. T.↗

Estimation of aerodynamic forces and moments on a steadily spinning airplane

A semiempirical method is presented for the estimation of aerodynamic forces and moments on a steadily rotating airplane model in a spin tunnel. The approach is based on the application of strip theory to determine a part of the aerodynamic coefficient (including rotational velocity) and then estimation of increments to these coefficients because of rotational flow over the stalled airplane. The theory is applied to a light, single-engine, general aviation airplane and the results are compared with the corresponding spin tunnel rotary balance test data.

Pamadi, B. N.↗