Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SNL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,549 records · Page 86

Summary of the First Neutron Image Data Collected at the National Ignition Facility

A summary of data and results from the first neutron images produced by the National Ignition Facility (NIF), Lawrence Livermore National Laboratory, Livermore, CA, USA are presented. An overview of the neutron imaging technique is presented, as well as a synopsis of the data collected and measurements made to date. Data form directly driven, DT filled microballoons, as well as, indirectly driven, cryogenically layered ignition experiments are presented. The data presented show that the primary cores from directly driven implosions are approximately twice as large, 64 +/- 3 um, as indirect cores (25 +/- 4 and 29 +/- 4 um and more asymmetric, P2/P0 = 47% vs. -14% and -7%. Further, comparison with the size and shape of X-ray image data from on the same implosions show good agreement, indicating X-ray emission is dominated by the hot regions of the implosion. This work was performed for the U.S. Department of Energy, National Nuclear Security Administration and by the National Ignition Campaign partners; Lawrence Livermore National Laboratory (LLNL), University of Rochester -Laboratory for Laser Energetics (LLE), General Atomics(GA), Los Alamos National Laboratory (LANL), Sandia National Laboratory (SNL). Other contributors include Lawrence Berkeley National Laboratory (LBNL), Massachusetts Institute of Technology (MIT), Atomic Weapons Establishment (AWE), England, and Commissariat `a l’ ´ Energie Atomique (CEA), France.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Long Range Active Detection of HEU Based on Thermal Neutron Multiplication

We report on the results of measurements of proton irradiation on a series of targets at Brookhaven National Laboratory’s (BNL) Alternate Gradient Synchrotron Facility (AGS), in collaboration with LANL and SNL. We examined the prompt radiation environment in the tunnel for the DTRA-sponsored series (E 972), which investigated the penetration of air and subsequent target interaction of 4 GeV proton pulses. Measurements were made by means of an organic scintillator with a 500 MHz bandwidth system. We found that irradiation of a depleted uranium (DU) target resulted in a large gamma-ray signal in the 100-500 µsec time region after the proton flash when the DU was surrounded by polyethylene, but little signal was generated if it was surrounded by boron-loaded polyethylene. Subsequent Monte Carlo (MCNPX) calculations indicated that the source of the signal was consistent with thermal neutron capture in DU. The MCNPX calculations also indicated that if one were to perform the same experiment with a highly enriched uranium (HEU) target there would be a distinctive fast neutron yield in this 100-500 µsec time region from thermal neutron-induced fission. The fast neutrons can be recorded by the same direct current system and differentiated from gamma ray pulses in organic scintillator by pulse shape discrimination.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

COMPOSE-HPC: Software Composition for Extreme Scale Computational Science and Engineering

Software composition is an important aspect of computational science software engineering due to large scale production science codes involving multiple programming languages, execution and concurrency models. To date, programmers must manage the complexity of building and maintaining such systems largely by hand with minimal (if any) automated assistance. As such, a great deal of programmer time is spent generating and maintaining code which leads to a high maintenance and development cost, as well as an increased risk of errors being introduced by hand than would be expected in an automated system. COMPOSE-HPC was a multi-institutional effort, with the Galois contribution focused on a specific area of code analysis and software infrastructure. Specifically, Galois led the design and implementation for the Parser for Annotations in a User-specified Language (PAUL), as well as collaborating with SNL and LLNL on the Retargetable Open Transformation Engine (ROTE). Both components were built on top of the ROSE compiler infrastructure from LLNL. All artifacts developed under the COMPOSE-HPC program are available on the github.com and sourceforge.net open source hosting sites under permissive BSD3 software licenses.

97 MATHEMATICS AND COMPUTING↗

Geologic Assessment of the Damage Zone from the Second Test at Source Physics Experiment-Nevada (SPE-N)

The National Center for Nuclear Security, established by the U.S. Department of Energy, National Nuclear Security Administration (NNSA), is conducting a series of explosive tests at the Nevada National Security Site that are designed to increase the understanding of certain basic physical phenomena associated with underground explosions. These tests will aid in developing technologies that might be used to detect underground nuclear explosions in support of verification activities for the Comprehensive Nuclear-Test-Ban Treaty. The initial project is a series of explosive tests, known collectively as the Source Physics Experiment-Nevada (SPE-N), being conducted in granitic rocks. The SPE-N test series is designed to study the generation and propagation of seismic waves. The results will help advance the seismic monitoring capability of the United States by improving the predictive capability of physics-based modeling of explosive phenomena. The first SPE N (SPE-N-1) test was conducted in May 2011, using 100 kg of explosives at the depth of 54.9 m in the U 15n source hole. SPE-N-2 was conducted in October 2011, using 1,000 kg of explosives at the depth of 45.7 m in the same source hole. The SPE-N-3 test was conducted in the same source hole in July 2012, using the same amount and type of explosive as for SPE-N-2, and at the same depth as SPE-N-2, within the damage zone created by the SPE-N-2 explosion to investigate damage effects on seismic wave propagation. Following the SPE-N-2 shot and prior to the SPE-N-3 shot, the core hole U-15n#10 was drilled at an angle from the surface to intercept the SPE-N-2 shot point location to obtain information necessary to characterize the damage zone. The objective was to determine the position of the damage zone near the shot point, at least on the northeast, where the core hole penetrated it, and obtain information on the properties of the damaged medium. Geologic characterization of the post-SPE-N-2 core hole included geophysical logging, a directional survey, and geologic description of the core to document visual evidence of damage. Selected core samples were provided to Sandia National Laboratories (SNL) for measurement of physical and mechanical properties. A video was also run in the source hole after it was cleaned out. A significant natural fault zone was encountered in the angle core hole between 5.7 and 7.5 m from the shot point. However, several of the fractures observed in the core hole are interpreted as having been caused by the explosion. The fractures are characterized by a “fresh,” mechanically broken look, with uncoated and very irregular surfaces. They tend to terminate against natural fractures and have orientations that differ from the previously defined natural fracture sets; they are common starting at about 5.4 m from the shot point. Within about 3.3 m of the shot point to the end of the recovered core at 1.6 m from the shot point, some of the core samples are softer and lighter in color, but do not appear to be weathered. It is thought this could be indicative of the presence of distributed microfracturing.

SPE, Source Physics Experiment, geology↗

NREL's Water Power Software Makes a Splash; NREL Highlights, Research & Development, NREL (National Renewable Energy Laboratory)

WEC-Sim is a DOE-funded software tool being jointly developed by NREL and SNL. WEC-Sim computationally models wave energy converters (WEC), devices that generate electricity using movement of water systems such as oceans, rivers, etc. There is great potential for WECs to generate electricity, but as of yet, the industry has yet to establish a commercially viable concept. Modeling, design, and simulations tools are essential to the successful development of WECs. Commercial WEC modeling software tools can't be modified by the user. In contrast, WEC-Sim is a free, open-source, and flexible enough to be modified to meet the rapidly evolving needs of the WEC industry. By modeling the power generation performance and dynamic loads of WEC designs, WEC-Sim can help support the development of new WEC devices by optimizing designs for cost of energy and competitiveness. By being easily accessible, WEC-Sim promises to help level the playing field in the WEC industry. Importantly, WEC-Sim is also excellent at its job! In 2014, WEC-Sim was used in conjunction with NREL’s FAST modeling software to win a hydrodynamic modeling competition. WEC-Sim and FAST performed very well at predicting the motion of a test device in comparison to other modeling tools. The most recent version of WEC-Sim (v1.1) was released in April 2015.

16 TIDAL AND WAVE POWER↗

Heating and Cooling System Design for a Modern Transportable Container

Sandia National Laboratories (SNL) has been tasked with the design of a modern transportable container (MTC) for use in high reliability transportation environments. The container is required to transport cargo capable of generating its own heat and operate under the United States’ climatic extremes. In response to these requirements, active heating and cooling is necessary to maintain a controlled environment inside the container. The following thesis project documents the design of an active heating, active cooling, and combined active heating and cooling system (now referred to as active heating and cooling systems) through computational thermal analyses, scoping of commercial system options, and mechanical integration with the container’s structure.

42 ENGINEERING↗

FL V1.3

A library of utility classes for computer vision. Contains implementations of various well-known image processing techniques, such as interest point operators and region descriptors. Includes interfaces to various libraries for image and video I/O, as well as an interface to LAPACK/BLAS. FL was developed at the University of Illinois, Urbana-Champaign (UIUC) and released under an open source license. Version 1.2 was a maintenance release provided by SNL under the LGPL license. Version 1.3 is a maintenance release, containing the following changes: - Improved image format handling. Now handles strided and planar memory layouts and a wider range of pixel formats. - Improved image file I/O, including better support for metadata, a wider range of stored pixel types, and a couple of new file formats. - Improvements to DOG and SIFT, and efficiency improvements in low-level convolution. - Improvements to networking, including a generic TCP listener. - Various improvements to numerical processing. The HISTORY file included in the distribution contains a more detailed description of the changes.

Rothganger, Frederick↗

BRISC v.1.0

BRISC is a developmental prototype for a nextgeneration “systems-level” integrated performance and safety code (IPSC) for nuclear reactors. Its development served to demonstrate how a lightweight multi-physics coupling approach can be used to tightly couple the physics models in several different physics codes (written in a variety of languages) into one integrated package for simulating accident scenarios in a liquid sodium cooled “burner” nuclear reactor. For example, the RIO Fluid Flow and Heat transfer code developed at Sandia (SNL: Chris Moen, Dept. 08005) is used in BRISC to model fluid flow and heat transfer, as well as conduction heat transfer in solids. Because BRISC is a prototype, its most practical application is as a foundation or starting point for developing a true production code. The sub-codes and the associated models and correlations currently employed within BRISC were chosen to cover the required application space and demonstrate feasibility, but were not optimized or validated against experimental data within the context of their use in BRISC.

Source record↗

Algae Biofuels Co-Location Assessment Tool

ABCLAT was built to help any model user with spatially explicit Nitrogen, Phosphorous, and Carbon Dioxide nutrient flux information, and solar resource information evaluate algal cultivation potential. Initial applications of this modeling framework include Algae Biofuels Co-Location Assessment Tool Canada and Australia. The Canadian application was copyrighted November 29th 2011 as the Algae Biofuels Co-Location Assessment Tool for Canada. This copyright assertion is for the general framework from which any country or region with the requisite data could create a regionally specific application. The ABCLAT model framework developed by SNL looks at the growth potential in a given region as a function of available nutrients from wastewater and other sources, carbon dioxide from power plants, available solar potential, and if available, land cover and use information. The model framework evaluates the biomass potential, fixed carbon dioxide, potential algal biocrude and required land area for nutrient sources. ABCLAT is built with an object-oriented software program that can provide an easy to use interface for exploring questions related to aigal biomass production.

Source record↗

Results of Partially-Reflected Critical Experiments in Square-Pitched Arrays of Water-Moderated 6.9 Percent Enriched Fuel Rods

The Seven Percent Critical Experiment (7uPCX) was designed to provide benchmark criticality and reactor physics data for water-moderated pin-fueled nuclear reactor cores. The enrichment of the fuel was chosen to explore the enrichment range above the current 5% ceiling for US commercial pressurized water reactors. The experiment was part of the US Department of Energy (DOE) Nuclear Energy Research Initiative (NERI) Project 01-124 titled “Reactor Physics and Criticality Benchmark Evaluations for Advanced Nuclear Fuel”. The NERI project was a collaboration between AREVA Federal Services, LLC; the University of Florida; Oak Ridge National Laboratory; and Sandia National Laboratories (SNL). The experiments at Sandia are currently supported by the DOE National Nuclear Security Administration Nuclear Criticality Safety Program. Two sets of benchmark experiments have been completed and documented as LEU-COMP-THERM-080 and LEU-COMP-THERM-078. Those experiments were done with the number of fuel rods in the fully-reflected array as the approach parameter. The experiments reported here are similar to those in LEU-COMP-THERM-080 except that the arrays are partially-reflected – the arrays were larger than would be possible with full reflection and the approach-to-critical experiments were done with the depth of the water in the critical assembly as the approach parameter. These experiments are reported as LEU-COMP-THERM-096.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Quantifying the Level of Cross-State Renewable Energy Transactions

This analysis provides first-ever assessment of the extent to which renewable energy is crossing state borders to be used to meet renewable portfolio standard (RPS) requirements. Two primary methods for data collection are Renewable Energy Certificate (REC) tracking and power flow estimates. Data from regional REC tracking systems, state agencies, and utility compliance reports help understand how cross-state transactions have been used to meet RPS compliance. Data on regional renewable energy flow use generator-specific information primarily sourced from EIA, SNL Energy, and FERC Form 1 filings. The renewable energy examined through this method may or may not have actually been used to meet RPS compliance.

small generators, incentive payments, power purcha↗

Wave-particle interactions in nonstationary plasma

Waves have proven to be an immensely useful tool for manipulating magnetically confined fusion plasmas. Our sophisticated understanding of the physics of waves and their interactions with charged particles in such plasmas is aided by the fact that the waves often can be treated as perturbations of an essentially stationary background, simplifying their mathematical treatment. On the other hand, despite the rapid, ongoing advancement of the world's most sophisticated plasma compression experiments, such as NIF (LLNL) and Z (SNL), the phenomenology of wave-particle interactions in the sort of nonstationary plasma environments exemplified by these experiments has gone relatively unexplored. In plasmas undergoing compression, expansion, ionization, and recombination, embedded waves can have very unusual and possibly useful properties. The introduction of explicit time-dependence into some classic problems in plasma wave physics has revealed the nature in which nonstationary processes impact all stages of a wave's lifetime, including its undamped linear and nonlinear dynamics as well as its collisionless and collisional damping. A number of new insights are revealed, including the discovery of an induced, switch-like collisionless damping mechanism capable of producing prescribed bursts of heat, current, magnetic field energy, and/or voltage in time-evolving plasma; a novel method for optimizing plasma-based acceleration of particle beams; enhanced understanding of the effect of waves on plasma compressibility; and the first numerical confirmation of a new, transparent analytical theory of nonlinear wave dynamics. To describe numerically all these effects, novel particle-in-cell simulations were developed. The findings not only stand to expand on the basic physics of waves in plasmas, but they also point toward potentially beneficial applications in the laboratory.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Using Deep Machine Learning to Conduct Object-Based Identification and Motion Detection on Safeguards Video Surveillance

Video surveillance is one of the core monitoring technologies used by the International Atomic Energy Agency (IAEA) Department of Safeguards at safeguarded nuclear facilities worldwide. Current IAEA image-review software has functions for scene-change detection, black image detection and missing scene analysis, but their capabilities are not optimum. The current workflow for the detection of safeguards relevant events heavily depends on inspectors’ laborious visual examination of surveillance videos, which is a time-consuming process and prone to errors. To improve the accuracy of the process and reduce inspectors’ burden, the paper proposes using deep machine learning to detect objects of interest in video streams and to conduct object-based motion detection. The hypothesis of this work is that deep machine learning will reduce the burden on inspectors and reduce errors by automatically locating and identifying objects of interest in video streams. Objects of interest include casks and fuel assemblies that are typically monitored by inspectors. The algorithm being developed in this work is based on a computationally efficient deep machine learning algorithm – You Only Look Once (YOLO) – but is further devised to address specific challenges related to the operation of nuclear facilities. The developed model (which is called YOLO-NSG – YOLO for Nuclear Safeguards) is evaluated with data sets collected at the test facilities at Brookhaven National Laboratory (BNL) and Sandia National Laboratories (SNL). The initial focus of the research is for application at safeguarded nuclear reactors, such as pressurized heavy-water reactors, where video surveillance is broadly deployed, but can be extended to other use cases of nuclear safeguards. The detailed structure of YOLO-NSG model is introduced and the test results are reported in the paper.

36 MATERIALS SCIENCE↗

Silicon Carbide Multilayer Piping for High Temperature sCO 2 Brayton Cycle

Efficiencies of greater than 50% in supercritical carbon dioxide (sCO 2 ) Brayton power cycle systems can be achieved only at turbine inlet temperatures of above 700°C. In support of the push to higher temperatures, a finite element model was developed by Materials Research & Design, Inc. (MR&D) with support from Ceramic Tubular Products, LLC. (CTP) to guide the refinement of CTP’s high temperature ceramic multilayer piping. The multilayer technology combines the advantages of a monolithic silicon carbide (SiC) tube and a SiOC f /SiOC ceramic matrix composite (CMC), the result of which is a material with high-temperature strength and stability, high mechanical and thermal shock resistance, and high corrosion resistance. In addition to fabricating test specimens to refine the finite element model, long-duration, high temperature CO 2 exposure tests were performed by Sandia National Laboratories (SNL) on two varieties of inner monolithic SiC.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Recent Developments in the WEC-Sim Open-Source Design Tool: Preprint

WEC-Sim (Wave Energy Converter SIMulator) is an open-source code for simulating wave energy converters, which has been actively developed and applied to simulate a wide variety of device archetypes and has become a popular tool since its initial release in 2014. WEC-Sim is developed jointly by the National Renewable Energy Laboratory (NREL) and Sandia National Laboratories (SNL) within the MATLAB/SIMULINK environment. Figure 1 illustrates a general wave-to-wire model which begins with a deployment site resource characterization, which is used to complete the hydrodynamic simulation of a single WEC (or array), with the power generation profile imported to a grid simulator to understand the influence on the local electrical network. While modelling the entire wave-to-wire is difficult and encompass multiple time scales and physics, WEC-Sim is focused on the hydrodynamics simulation to predict, analyze and optimize WEC dynamics and power performance. WEC-Sim simulations are performed in the time domain based on the radiation and diffraction method using hydrodynamics coefficients derived from boundary element method (BEM) based-frequency-domain potential flow solvers (e.g., WAMIT, NEMOH, Capytaine, or ANSYS-AQWA). Within this level of modeling fidelity, WEC-Sim can handle floating body hydrodynamics, mechanical and electrical power generation methods, advanced control implementation, mooring systems, and other unique applications such as desalination. Table 1 lists additional WEC-Sim functionalities, which are created using prebuilt Simulink blocks and MATLAB scripts that can simulate a wide range of floating systems and the corresponding auxiliary subsystems.

hydrodynamics modeling↗

Assembly Level Modeling and Transportation Damage Prediction of Used Nuclear Fuel (UNF) Cladding

Under U.S. Nuclear Regulatory Commission (NRC) regulations, UNF must maintain its integrity in such a way that it can withstand the physical forces of handling and transportation associated with restaging the fuel and moving it to a different location such as an interim storage site, a geologic repository, or a treatment/recycling facility. Hence, understanding mechanical performance under cumulative loading stemming from normal conditions of storage (NCS), transfer from storage container to transport container if needed, and normal conditions of transport (NCT) is necessary as it establishes part of the safety basis via maintaining the fuel confining boundary (geometry), maintaining criticality safety, and is one of the critical components to the preservation of retrievability. An initial demonstration of modeling and simulation capabilities was performed as part of a collaborative effort between Pacific Northwest National Laboratory (PNNL), Sandia National Laboratory (SNL), Idaho National Laboratory (INL), Oak Ridge National Laboratory (ORNL), and the Transportation Technology Center Inc. (TTCI). This demonstration completed preliminary deterministic evaluations of moderate-to-high burnup UNF mechanical performance under NCS and NCT conditions. This paper focuses on work performed by PNNL on the assembly level modeling of a UNF assembly and fuel cladding damage predictions under NCT loads. The Finite Element (FE) model created for a 17 x 17 Pressurized Water Reactor (PWR) optimized fuel assembly (OFA) is discussed along with the communications to and from the fuel rod-level and cask-level models. Additionally, the methodology for determining cumulative damage is discussed including the 3000 mile damage prediction from a 10 second simulation. The damage results are shown for five shock and vibration broadened loading histories. It is found that predicted cladding strains were not large enough to cause structural failure, but cyclic strains roughly projected for the entire route were significant in some cases. The total damage from summation of the worst shock and vibration cases evaluated is approximately 18% of the expected fatigue limit. Therefore it is predicted that the fuel rods do not fail during NCT given the assumptions used throughout this initial demonstration.

used nuclear fuel, UNF, trasportation, damage, fue↗

Disassembly and Sanitization of Classified Matter

The Disassembly Sanitization Operation (DSO) process was implemented to support weapon disassembly and disposition by using recycling and waste minimization measures. This process was initiated by treaty agreements and reconfigurations within both the DOD and DOE Complexes. The DOE is faced with disassembling and disposing of a huge inventory of retired weapons, components, training equipment, spare parts, weapon maintenance equipment, and associated material. In addition, regulations have caused a dramatic increase in the need for information required to support the handling and disposition of these parts and materials. In the past, huge inventories of classified weapon components were required to have long-term storage at Sandia and at many other locations throughout the DoE Complex. These materials are placed in onsite storage unit due to classification issues and they may also contain radiological and/or hazardous components. Since no disposal options exist for this material, the only choice was long-term storage. Long-term storage is costly and somewhat problematic, requiring a secured storage area, monitoring, auditing, and presenting the potential for loss or theft of the material. Overall recycling rates for materials sent through the DSO process have enabled 70 to 80% of these components to be recycled. These components are made of high quality materials and once this material has been sanitized, the demand for the component metals for recycling efforts is very high. The DSO process for NGPF, classified components established the credibility of this technique for addressing the long-term storage requirements of the classified weapons component inventory. The success of this application has generated interest from other Sandia organizations and other locations throughout the complex. Other organizations are requesting the help of the DSO team and the DSO is responding to these requests by expanding its scope to include Work-for- Other projects. For example, Pantex personnel have asked the DSO team to assist them with the destruction of their stored classified components. The DSO process is in full-scale operation and continues to grow and serve SNL/NM and DOE by providing a solution to this evolving disposal issue. For some time, SNL has incurred significant expenses for the management and storage of classified components. This project is estimated to save DOE and Sandia several hundreds of thousands of dollars while the excess inventory is eliminated. This innovative approach eliminates the need for long-term storage of classified weapons components and the associated monitoring and accounting expenditures.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗